Search Documents

By W. C. Yates

Lack of visibility from large, open-pit haulage truck cabs has become a serious safety problem. Anaconda conducted a research program to develop a low cost system to alert haulage truck operators to small vehicles present in blind areas. Several systems were developed and tested. As open-pit haulage truck size has increased, so has the size of the blind areas. Mine utility vehicles, pickup trucks, and cars are concealed within these blind areas and become safety hazards. Figure 1 shows the typical blind areas of a 136 t (150-ton) haulage truck. The areas of greatest concern are at the rear center and front right corner of the truck. In these "no visibility" areas many small vehicles have been crushed by large haulage trucks at various mine sites. In most instances, the occupants escaped the vehicle before it was destroyed. But injuries and death have occurred. In most cases, the accidents were attributed to negligence or carelessness by the small vehicle driver. The limited visibility problem still exists, though, and a solution is needed. Initial Solution The usual plane mirror on the driver's side and the convex mirror on the right front of the haulage truck allow only limited rear visibility. The typical, right side convex mirror is generally small and difficult to locate at a glance. This convex mirror also presents an image that distorts distance perception. These mirrors are of¬ten broken and immediate replacement not demanded or made. The US Bureau of Mines, in a contract with M.B. Associates, San Ramon, CA, developed an improved visibility system. It consisted of a larger, left view mirror and unique, blind area viewer. The large 230 x 690 mm (9 x 27 in.) left mirror has a small convex spot mirror near the bottom. The entire unit can be quickly replaced if broken. The large size provides a full view of driver orientation features such as the rear tire and the top of the load bed. The right 300 x 410 mm (12 x 16 in.) mirror has a convex surface and is quite rugged. The 510 mm (20 in.) spherical radius presents the operator with some distance distortion, but objects in its view are easily seen. The "blind area viewer" consists of a modified fresnel lens that allows the driver to "look around the corner." Installation of three of these lenses on the front of each haulage truck is rec¬ommended for adequate blind area coverage. This system significantly increases an operator's field of view and allows viewing of objects within about 3 m (9.8 ft of the truck. Many open-pit mines are nor mounting on smaller vehicles a long whip with a flag and lamp or both. This increases vehicle visibility to haulage truck operators. The whip is permanently attached to the mine vehicle. It can also be magnetically attached to transient vehicles. The whip system. though, is inadequate for visibility in the critical rear and right front blind areas. Alternate Solutions All of these visibility aids as¬sume an attentive driver. In addi¬tion, areas such as the rear blinc, area are not covered. Based on the inadequacy of existing visibility systems, Anaconda made a com mitment to further the truck de¬tection technology. The best ap¬proach was considered to be ar active system. It would notify the haulage truck operator that an en¬croaching vehicle is present. Sev¬eral systems were considered, in¬cluding ultrasonics and elec¬tromagnetics. For the ultrasonic system, com mercial and in-house design were looked at. Designing an( building transducers with the spe cific beam shape to match the haulage truck blind spots re¬quired a major technological breakthrough. False alarms ap¬peared difficult to prevent en¬tirely. They were caused by pass¬ing, trailing, or leading vehicles a., well as nonthreatening objects. As a result of these problems, the ul¬trasonic technique was not pur sued. An alternative, an electro

Jan 7, 1982

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., under contract to the Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1986

By P. W. Conrad, C. Todd, N. West, R. Kramer

"Surface subsidence caused by both underground room-and-pillar mining operations and solution mining operations have each been studied separately, but never combined. In 2008, FMC Minerals began using solution mining at its Westvaco Mine as a secondary extraction method in an area that had been previously mined using the room-and-pillar mining method. Mining regulations require that subsidence associated with underground mining activities be monitored and measured annually. Researchers at Montana Tech were able to develop a relationship between measured surface mine subsidence and solution mining that can be used at the Westvaco Mine to estimate the production of trona from solution mining operations. PROJECT BACKGROUND FMC Minerals (FMC) has increased the production of trona from its Westvaco Mine near Green River, Wyoming, using solution mining as a secondary extraction method in an area previously mined using the room-and-pillar method. The area of interest was mined until 2001 with the use of a borer miner at a depth of approximately 1,600 feet. Currently, FMC determines the amount of trona produced using its solution mining operations by measuring the dissolved solids pumped from the mine. This approach, however, does not account for the location from which the trona was removed. The location from which the trona was removed and the size of the cavern created by the solution mining operations is important to FMC’s mine planning. FMC believed that with proper investigation of the subsidence at the Westvaco test site, a correlation might be found that would allow for the use of surface subsidence measurements to estimate the amount and location of trona production from the solution mining activities. The primary goal of this project, conducted by Montana Tech, was to find a relationship between the measured subsidence and the solution mining activities. The project attempted to model the relationship between the measured subsidence and the solution cavern using Salt_Subsid, an existing subsidence software package from the Solution Mining Research Institute (SMRI), to determine the program’s usefulness for locating and developing the cavern created by solution mining activities. The project also attempted to develop an equation that could be used to predict solution trona production based on measured subsidence. The data used in this study were collected over a seven year period, 2008 through 2014."

Jan 1, 2016

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants indicated having processes in place for what should be done once an imminent danger situation is identified. Critically, however, they report having no systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. While this is important for all imminent danger situations (e.g., failure to lockout/tagout), it is especially important for those situations that are not immediately recognizable as imminent danger. In this paper, we identify and describe, three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication, and specialized training to increase awareness of imminent danger situations. INTRODUCTION In recent years, the metal and nonmetal (M/NM) mining sector, as categorized by MSHA, experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured; that is twice the number of fatalities that occurred in each of the previous two years (MSHA, 2015a). As a way to address this increase, the Mine Safety and Health Administration (MSHA) issued a program policy letter (P15-IV-01) suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners (MSHA 2015b).” The goal of workplace examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 1, 2018

By Per H. Fahlstrom

The story of the Aitik mine begins in the early thirties. At that time blocks of low grade chalcopyrite impregnations were found in Swedish Lapland not far from the present mine, some 40 miles north of the arctic circle in the vicinity of the iron ore field at Gällivare. The ore prospect was viewed upon several times. By means of geophysical studies and an extensive diamond drilling programme during the end of the fifties and the beginning of the sixties a huge low grade ore body was discovered under the muskeg overburden. In 1965 55 million tons of ore with 0.5 % Cu was known to a depth of 160 ft. In 1970 the ore reserves had increased to 165 million tons with 0.40 g, Cu at a depth of 400 ft. Decision to develop the mine and to start production at an annual production of 2,2 million tons was made in 1965. A mine and concentrating plant, the A section, went on stream in 1968. In 1970 decision was made to expand the production with 3,3 million tons pr year. A second section of the plant, the B section, went on stream during the end of 1972 and the beginning of 1973 The production in the initial plant has been increased to 3,1 million tons pr year and during 1974 the combined A and B sections are expected to treat' about 7,2 million tons of ore. The two sections will treat 10,000 and 13,000 tons per day.

Jan 1, 1974

By Caroline L. Herzenberg

Recently, neutron-induced gamma spectrometry has been introduced and gained provisional acceptance as a method for continuous automated analysis of coal. Instrumentation based on this technique has been under development for and in testing at coal preparation plants and a coal gasifier. To provide a deeper understanding of, and extended capability in applying this method, theoretical calculations have been performed of the absorption of thermal neutrons by various coal compositions, and the thermal neutron capture prompt gamma emission spectra produced by these compositions have been calculated. Selected results of these computer calculations and the computer generated spectra are presented.

Jan 1, 1984

By D. Naden

Sulphuric acid leaching is the most common method of recovering uranium from its ores and in the following discussion various alternative low cost routes are investigated for recovering uranium from milled ore acid leach liquors. Historically uranium has been recovered from dilute impure leach liquors by packed bed ion exchange (IX), solvent extraction (SX) or a combination of both. All three process routes as commonly practised require complete separation of leached solids and liquids, as well as extensive solids washing in order to reduce soluble uranium losses to a minimum. Separation and washing are costly and often require equipment covering large areas of land. The size and capital cost of the post leach solids washing operation is controlled by the ease of washing the slimes fraction of the ore and the key to the problem of cost reduction, as many others have realised, lies in the ability to separate the slimes fraction of the ore from the more easily washed sands, to wash the sands in low cost equipment and to recover uranium from the slimes stream. Sands and slimes are usually defined in this context as the material larger than, and smaller than, 325 mesh (44 microns). The proposed flowsheets which minimise solid-liquid separation and washing have usually incorporated ion exchange (Refs 1,2,3), and resin in pulp is in fact practised in several mills in the USA (Ref 1). The resins used in these flowsheets and [cranium] recovery throughout the world have been strong base resins which load rapidly and are moderately selective for the uranyl sulphate complex anion over the range of pH which is conveniently achieved in an acid leach operation. Strong base resins are, however, not as selective as weak base resins and weak base liquid reagents owing to the adsorption of competing anions, some of which find their way into the product while others act as resins poisons. Ion exchange using strong base resins must therefore be followed by a more selective weak base SX purification step if pure yellow cake is required.

Jan 1, 1976

By R. L. Eppley

The Blacklick Creek Watershed Association was awarded a $158,000 Growing Greener grant from the Pennsylvania Department of Environmental Protection in 2002 for the design and construction of a sulfate reducing bioreactor (SRBR) cell to treat acidic discharge from the Judy 14 abandoned underground coal mine near Indiana, PA. The vertical flow SRBR was designed to treat 38 liters per minute of MIW containing elevated concentrations of aluminum and iron. Other treatment systems at this site plugged due to aluminum precipitates; this problem did not occur in the SRBR. The bioreactor has been periodically overloaded with flows up to six times the design rate. To date, the only maintenance performed on the unit has been the addition of hay to the surface of the unit in response to less than expected performance. The periodic hay additions appear to have restored the SRBR to nearly post-construction levels. Since construction, the SRBR has treated about 136,000 cubic meters (36 million US gallons) of MIW.

Jan 1, 2010

By Luis Yacher

CONTAC Engineers is a Chilean based company which works on process control and automation, principally for the minning industry. Jointly with other local and international engineering firms, CONTAC has participated in most of the last expansion and modernization plans being carried out at the Chilean pinning industry. At presente, CONTAC is involved on a research and development plan for the design and implementation of new instrument and process control procedures for mineral process automation. One of these efforts is the design of an ore size analyzer for coarse ore being transported over a conveyor belt. A feasibility and prototype study was made at a SAG Mill Plant and currently a high resolution, high speed analyzer is being developed. It will became available on early 1986.

Jan 1, 1986

By Thon T. Gin

The lithologic, mineralogic, and magnetic beneficiation characteristics of the iron formation at U. S. Steel's Atlantic City Ore Mine, Fremont County, Wyoming, have been determined. The iron formation averages about 30 percent Fe content, and varies from 125 feet to about 500 feet in thickness. It is composed of interbedded magnetite-rich quartzites, magnetite-quartz-amphibole schists, and amphibole-chlorite schists. Quartz, actinolite-tremolite, chlorite, and magnetite are the essential mineral constituents. These rocks are differentiated into four major ore types on the basis of their relative quartz and amphibole content. The iron content of the magnetic concentrate decreases and the silica content increases with decreasing grain size and increasing amphibole content in each ore type at the same fineness of grind. Criteria were developed to enable the mine operator to recognize the ore types and to blend them to produce a more uniform concentrator feed. This results in less variation in product quality and requires fewer changes in operating conditions-in the concentrator.

Jan 1, 1965

By Donald E. Ralston, V. Rajaram, Michael N. Greeley, John W. Peters, Terry J. Laverty, F. S. Kendorski, Peter G. Chamberlain, J. Brent Hiskey, William C. Larson

Preliminary figures from the US Mine Safety and Health Administration show 801 underground metal mines and 490 surface metal mines, at the end of 1981, up from 663 and 383, respectively, in 1980. Preliminary MASH figures also show 207 underground nonmetal mines and 1070 surface nonmetal mines at the end of 1981, compared with 167 and 1092, respectively, last year. In addition, preliminary MASH figures show there were 14,676 mineral extraction operations on the surface and 3845 underground at the end of 1981, versus 14,951 and 3675, respectively, for last year. The number of mines, then, in three of four categories increased significantly, while having a lower net total of just 2% in the other category. And the number of underground extraction operations increased nearly 5% for the year, while surface operations were down less than 2%. But despite operations totals that mostly held their own or showed significant increases, it was a tough year for the nation's mining industry. The nonferrous segment of the industry had a bad year and 1982 may be no better, according to Business Week (Jan. 11, 1982), which adds that a turnaround is impossible unless the general economy recovers. Even then, with diminishing markets and overcapacity plaguing its products, the mining industry's condition "will be far from robust," the magazine says. The basic problem is that nonferrous metals-aluminum, copper, lead, molybdenum, nickel, and zinc-are tied to the most troubled sectors of the US economy. As recently as 1979, for example, more than 40% of all aluminum shipments went to the construction and transportation industries. Last year, these markets were down to 35% of aluminum shipments. And molybdenum sales to steel producers dropped by nearly 15% last year. Moreover, nonferrous products ended 1981 at disastrously low prices. Molybdenum oxide sold at $8.77/kg ($3.98/lb), half its $17.63/kg ($8/lb) price earlier in 1981 and aluminum was listed at $1.08/kg ($0.49/lb), compared with $1.54/kg ($0.70/lb) a year earlier. The Comex price of copper was $1.54/ kg ($0.70/lb), down from $3.11/kg ($1.41/lb) in early 1980, in real terms the worst copper price in 30 years. Lower prices led operators to cut their output and increase layoffs, shut down mines, and defer capital spending projects. In December, Duval Corp., a Pennzoil Co. subsidiary, shut all four of its US copper mines until March. Aluminum Co. of America had laid off 7.3% of its work force, shut nine of its 38 smelting lines, and entered 1982 operating at only 68% of capacity. Inco Ltd., the Free World's largest nickel producer, lost money in 1981, an estimated $11 million, for the first time since 1932. And, like Falconbridge Nickel Mines and other major nickel producers, had cut back on nickel production and was operating at only 63% of capacity (Forbes, Feb. 15, 1982). Amax, the country's largest molybdenum producer, had cut production by 20%. And Hanna Mining Co. sold lead for $5.07/kg ($2.30/lb), about $1.54/kg ($0.70/lb) below what it cost to produce. Another problem is that copper companies in the next few years must come to terms with problems of aging smelters. Some companies are simply closing them. In 1980, Anaconda closed its 75-year-old Butte, MT, smelter and is shipping concentrates to Japan, rather than modifying the smelter to meet environmental requirements. And oth Phelps Dodge Corp. and Asarco Inc. have antiquated smelters on which they will have to make decisions. The most troubled metal in 1982, Business Week said, will be molybdenum, with no real recovery in sight until the mid-1980s. High molybdenum prices in the late 1970s, caused in part by shortages, triggered overexpansion that will take years for the US market to soak up. On a more upbeat note, 1981 mergers might help stabilize the industry by providing funds for mining companies. Standard Oil Co. (Ohio) said it plans to spend $7 billion on Kennecott during the next 10 years for modernization and expansion. And Atlantic Richfield Co. said it will spend $500 million on Anaconda Copper Co. during the next five years. Another positive note was sounded by T. H. Adams of the United Banks of Colorado Inc. He said he expects the mining industry to experience moderate growth in 1982, led by "interest rate sensitive" demand from energy, electronics, and defense markets. And mining will be helped by "weak, but improved" construction and auto markets. The mining industry will be operating in an economy stronger than 1981, but still relatively sluggish by postwar standards, Adams predicted. Iron Ore Estimated US iron ore production in 1981 was 75.2 Mt (74 million long tons), up 6% from 70.7 Mt (69.6 million long tons) in 1980, though down from the 87.1 Mt (85.7 million long tons) produced in 1979. The mine value of usable iron produced from domestic mines was estimated at $3 billion. US iron ore was produced by 28 companies operating 35 mines, 26 concentration plants, and 16 pelletizing plants. The mines included 34 open pits and one underground mine. Byproduct ore recovered from copper- and titanium-mining operations accounted for less than 1% of total iron ore production. Fifteen mines operated by nine companies accounted for 94% of total

Jan 5, 1982

By Elmer H. Citron

The Monterey Coal Company, a wholly owned subsidiary of The Carter Oil Company of Houston, Texas, recently awarded a contract to build the Monterey No. 1 Preparation Plant, which will be located near Carlinville, Illinois, to the McNally Pittsburg Manufacturing Corporation. The preparation plant will be one of the most modern jig preparation plants in the State of Illinois. Illinois No. 6 coal will be delivered by a 48" slope belt having 35-degree carrying idlers, operating at 650 FPM and operating on an incline of nearly 17 degrees. The slope belt is driven by two 450 BP motors and will deliver the mined coal at the rate of 1800 TPH to a stationary step-type ' screen having six-inch openings. The overproduct from the stationary screen will discharge into a 10' x 24' McNally Rotary Breaker and the underproduct will bypass the rotary breaker. The rotary breaker is equipped with heavy manganese screens with 6 ½" diameter openings. The sized 6" x 0 coal from the stationary step screen and the rotary breaker will be discharged by gravity to a 4%" raw coal incline storage belt. The 48" raw coal storage belt will deliver the 6" x 0 sized coal at the rate of 1800 T?H to an 8000 ton concrete raw coal silo, 70 feet in diameter and 1x7 feet high. The 6" x 0 sized coal will be drawn from the concrete storage silo by seven (7) 36" wide reciprocating plate feeders. Five feeders are to have constant speed drives at a rated capacity of 145 TPH each. Two (2) feeders will have remote con- trolled variable speed drives, to provide a varying feed.

Jan 1, 1970

By Orlando Oliveros

The Los Bronces Mine and Concentrator, one of the three operating units of Compania Minera Disputada de Las Condes S.A. (an Exxon Minerals Co. affiliate), is located in the high Andes of East-Central Chile approximately 70 kilometers northeast of Santiago at an elevation of 3,650 meters above sea level. (Figure 1). Santiago, the capital city of Chile, is located at an elevation of about 500 meters above sea level and enjoys a very mild climate, similar to some areas of California. At the mine site, however, extremely heavy winter conditions prevail occasionally, with very heavy snow and the resulting snow avalanches endangering installations and people. At the same time, ideal skiing conditions are found at the nearby ski resort of Portillo and Farellones. Mount Aconcagua, the highest mountain in the western hemisphere is only about 55 kilometers further to the northeast of the Los Bronces mine.

Jan 1, 1983

By W. Blake, J. Whyatt

Sixty years of rock bursting in the Coeur d'Alene district has taught painful lessons and led to a number of practical advances in controlling rock-burst hazards. This paper summarizes these lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rock-burst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rock-burst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d'Alene district experience.

Jan 1, 2003

By C. J. Bise

Virtual reality (VR) is a concept in which the human experience of perceiving and interacting with a computer-modeled environment is achieved through the use of sensors and effectors. It is an advanced form of computer graphics. The images are generated based on where the user looks and how the user moves. As personal-computer-based (PC) instruction gains acceptance as an innovative approach to providing safety training, VR can provide a multisensory, rather than merely a multimedia, mode of presentation. New technology continues to be introduced into the mining industry to meet the productivity needs of coal and noncoal producers. There is also an increased need for more innovative training of mine workers. New technology and equipment designs often affect the basic causes of accidents. For example, the development of cabs and canopies for underground coal-mine equipment has reduced the number of accidents related to roof falls and rib rolls. However, safety-training specialists then had to focus on the machines themselves, because the modifications had the potential for causing "pinch-point" accidents. In fact, although the overall physical demands on mine workers have diminished, there has been an escalation in the concerns about trauma from repetitive physical activity. Thus, health-and-safety training specialists have shifted their atten¬tion to the recognition, evaluation and control of workplace hazards (Hancock and Hill, 1995). Recognizing that the spatial relationships of a workplace convey more information about hazards when experienced rather than described, trainers agree that simulation is the method of choice. Unfortunately, until recently, simulation systems were either simple software programs that did not come close to portraying the real experience or were complex hardware systems (such as flight simulators) that did, but at a cost of millions of dollars (Fritz, 1991). However, researchers and training specialists are excited about an emerging approach to work-force education based on virtual reality. VR is also described as cyberspace, immersive simulation, artificial reality, telepresence, virtual environment or virtual world (Meyer and Dunn-Roberts, 1992; Peterson, 1992). It represents a group of concurrent advances in computer and interface technologies. They enable an individual to interact in a multisensory way with a computer-generated environment. To achieve this, a typical VR system incorporates a computer that contains the necessary databases for producing realistic images and audio; a head-mounted display (HMD) or screen for viewing the images; and a three-dimensional controller, joystick or data glove for interacting with the computer-generated environment. If virtual reality is to become an effective tool for the safety training of mine workers, its attributes will have to be measured against other forms of delivery. Accordingly, Carr (1992) listed the following areas in which VR should be considered the method of choice: ? When training mistakes would be costly. ? When the necessary environment cannot be experienced in the real world. ? To build interfaces that are sensible and can be manipulated. ? To make training situations really "real." ?To make perceptible the imperceptible.

Jan 1, 1997

By T. P. Meloy

Current coal cleaning technology uses heavy media (HM) for the recovery of coal in particles larger than 1/16 of an inch. Through the use of float sink measurements of the feed and products to commercial HM unit operations, a selection function, sometimes called Tromp curve in the coal industry, can be computed. Since the selection function is a plot f the probability of a particle appearing in the float versus the particle density, the slope of the curve will be sharper at the point where the particle has a 50% chance f appearing in the float. Thus, the separation will be better. Fine-tuning a unit operation or a circuit of unit operations requires that the selection function be accurately known. By current practice, it is difficult to obtain an accurate measure of the slope because, when the selection function is plotted versus density, the data forms an S-shaped curve which lacks data points near the 505 point of the curve. This lack of sensitivity in measuring the slope means that small recovery improvements cannot be detected; thus, only large improvements are measurable. Since most engineering improvements are small when individually considered, but large when aggregated ever many small improvements, this lack of measurement sensitivity rules out the slew march toward improved efficiency. This paper presents a method of analyzing heavy media selection functions resulting in a far more effective measure of the selective function slope. Furthermore, this improved method is applied to a number of industrial coal cleaning plants for both heavy media and heavy media cyclones. Using the work of Hudy (1968), and Deurbrouck and Hudy (1972), selection functions for individual unit operations in each plant are calculated as a function f particle size as well as density.

Jan 1, 1982

By A. Griffiths

The? use of hydrogen peroxide to detoxify gold mill waste waters containing cyanide and other toxic substances is already an established technology. Recent advances have extended the range of application of hydrogen peroxide treatment to include the removal of complex iron cyanides, the simultaneous removal of cyanide and toxic metals down to very low levels and treatment of barren bleeds, CIP' pulps and tailings pond discharges. Three treatment plants are described here. Each was installed at a gold mine in North America in 1987 and each illustrates a different application of hydrogen peroxide. The need for individual design of the detoxification plant to fit particular requirements is shown by the examples chosen.

Jan 1, 1988

By James M. Griffin

Ladies and Gentlemen, There have been no less than ten major coal project financings in the last eighteen months. Each of these has been in the order of $100 million to $1 billion for the development of a coal property and its associated infrastructure. It is appropriate at this time to review the nature of these past financings. Why has there been so much activity? There are primarily two reasons. The first is due to the large number of contracts which were signed as a result of OPEC oil shocks. High projections were made for increased coal consumption particularly in world trade. This is distinct from domestic coal mine/power plant projects which often tap a government source of funds. Second is the high cost of coal development in the 1980's compared with a typical company's corporate borrowing capacity.

Jan 1, 1984

By N. Kuroda

A realistic simulation model has been used for designing longwall mining, especially for solving operational problems. This paper describes background, development, validation and some applications of the simulation model for mining people who are unfamiliar with O.R. or computer technique, as a simple planning tool. The following items were established: logical analysis and algorithmic design for practical longwall mining, structure of hypothesis behavioral organism, input parameters, using practical knowledge and operational statistics of the mechanized longwall system experienced for many years.

Jan 1, 1982

By William G. Holroyd

In January 1992, the Office of the US Trade Representative announced that the People's Republic of China had agreed to protect US intellectual property, including computer software, sound recordings, agrichemicals and pharmaceuticals. Under the agreement, China will make significant improvements in its patent, copyright and trade-secret laws. Ambassador Carla A. Hills, the US trade representative, said "this agreement should create significant opportunities for US firms interested in marketing high valued-added products to China." Principal beneficiaries will include the agrichemical and computer industries, as well as pharmaceutical, entertainment. The agreement will safeguard these industries' intellectual property, stimulating new exports to China and helping to generate additional growth in the US. Refractory grade bauxite was included in the mineral category of the $1.5 billion of Chinese products on which the US government threatened to impose an immediate 100% trade tariff. Refractory bauxite is available from Guyana and Brazil at higher cost and in different grades. However, refractory brick manufacturers would have had little choice but to pass on the costs to their consumers. Although the United States and China are separated by political ideology and internal governing structures, this agreement recognizes the importance of a $19 billion trading relationship. Consequently, the renewal of China's most favored-nation trading status in the US congress in -June 1992 was all but assured. Many US companies doing business in China and Hong Kong have been quietly increasing their investments since 1989. These companies can now concentrate on developing sales to the domestic Chinese market. This market is expected to surpass 1.2 billion people in 1995 and approach 1.3 billion by the end of the century.

Jan 1, 1993