Search Documents

By James D. Cooper

Long range projections of demand for nonmetallic minerals are presented, together with data on the domestic resources which are available or which can be made available to meet the requirements through the balance of the century. Past successes in solving nonmetallic mineral requirement problems are briefly reviewed to illustrate the capability for solving present and future problems of a similar nature. Major problems threatening the future supply of specific industrial minerals are described together with possible methods for assuring the necessary raw materials for future needs. The growing importance of environ- mental degradation, land use conflicts, and other important factors which affect several or all of the nonmetallic mineral industries is covered, and the necessity of planning for efficient and orderly extraction and rehabilitation of mineral deposits is stressed. The present Bureau of Mines methods and tools for long range planning are briefly discussed.

Jan 1, 1969

By M. T. Ityokumbul

Flotation columns and their variations are increasingly replacing conventional cells in mineral processing circuitry. While the operational characteristics of columns differ from those of conventional cells, the same scale-up methodologies are being employed in design. This practice may be attributed to poor understanding of the factors controlling throughput. The use of tall flotation columns is frequently justified on the requirement for increased particle residence time. It is shown that longer particle residence times in the column cell alone do not translate into increased recoveries. Throughput data from several industrial flotation column installations is presented. An attempt at using dimensional analysis to provide scale-up methodology for the factors controlling column throughput is made.

Jan 1, 1995

By J. Moreno, P. Sinton, R. Vogwill

Groundwater models are often used to estimate and optimize dewatering volumes, locations, and rates, as well as water supply production for mines. Projections of future dewatering rates are highly dependent on the conceptual model used as a basis for the numerical model. This paper presents an audit of modeled dewatering rates versus actual data and an examination of the reasons for discrepancies. The setting is a gold mine, in a collapsed volcanic crater breached by the ocean. Mining will occur to about 200m below sea level within a remnant geothermal system. A detailed hydrogeologic investigation was conducted to support dewatering and geothermal depressurization design for future mining operations. These studies included development of a three-dimensional model to simulate heat and density-coupled groundwater flow, using software developed by URS/Dames & Moore. In this paper, the groundwater modeling results prepared 5 years previously by others was audited using operational dewatering data. This model was then extended using the new mine schedule and actual locations for dewatering wells to predict future dewatering requirements. In addition, a comparison between “hot” and “cold” model results was used to assess the need to use a heat-coupled versus a standard groundwater model for dewatering predictions.

Jan 1, 2003

By Todd Minoski, Matthew McElhinney, Mark Mazzella, Morgan Sears, Craig Compton

The National Institute for Occupational Safety and Health (NIOSH) is staffed with Engineers, Geologists, and Field Technicians conducting a variety of ground control research. The mission of the ground control teams within the Mine Systems Safety Branch (MSSB) is to eliminate ground failures leading to mineworker injuries and fatalities. Advancing the science behind ground control relies heavily on conducting mutually beneficial research at participating mines which is detailed in specific references throughout the paper. The ground control teams have several types of field instruments at their disposal to measure the ground response in underground mines. These include borehole pressure cells (BPCs), vibrating wire stress meters (VWs), hollow inclusion cells (Hi-Cells), roof and rib extensometers, load cells, and convergence meters. These instruments are used to measure changes in pressure, strain, and displacement within the underground environment. Instrumentation data is collected automatically using intrinsically safe or MSHA permissible dataloggers if required. Information is transmitted to the dataloggers using approved cable to distances of 200–1,000 ft. depending on the type of datalogger being used. Once mining is completed, the dataloggers are retrieved and brought to the surface, providing in-mine data to mine management and engineers for the conditions currently being encountered in a particular mine. This data, in conjunction with geologic data and stress mapping, can be used to validate numerical models. The practical application of these models is extremely important for mine management and engineers, particularly when faced with more challenging mine environments. Insight gained from applying these models can be used to make better engineering-based judgments for areas that will be mined in the future. The impact of such applications can result in a reduction of ground-fall accidents and injuries as well as generally safer working conditions.

Feb 1, 2024

By R. Schipper

Two bench scale biochemical reactors (BCRs) were operated over a period of 3 months for the removal of uranium, radium, and selenium from mining influenced water (MIW). A BCR is an anaerobic reactor comprised of organic and inorganic substrate including woodchips, straw, sawdust, and limestone. Uranium and selenium are removed in a BCR by biological reduction of oxidized species (i.e., selenite, selenate) to less soluble forms (Pahler et al. 2007, Blumenstein et al. 2008, Rutkowski et al. 2013). It is believed that radium may be removed through absorption to the biomass in the BCR. The bench scale BCRs were constructed of 6 inch PVC columns with a top to bottom flow configuration. The bench influent water consisted of three different water ratios from two adit seeps. BCR hydraulic retention times of 24 to 36 hours were targeted during the study. Influent concentrations ranged from 19 ug/L to 1.86 mg/L for dissolved uranium, 12 ug/L to 270 ug/L for dissolved selenium, and 4.9 pCi/L to 24 pCi/L for radium 226. The average and maximum dissolved uranium removal was 93.6% and 98.5% respectively, the average and maximum dissolved selenium removal was 93.3% and 98.9% respectively, and the average and maximum radium 226 removal was 89.5% and 100% respectively.

Feb 23, 2014

By R. G. Benson

The San Luis deposit of Costilla county, Colorado contained 11,021,000 tonnes (12,149,000 tons) of ore at 1.4 g/t (0.040 oz/st) gold in two minable zones. Gold mineralization is associated with silicification and quartz-sericite-pyrite alteration localized in breccias along a low-angle detachment fault zone in Precambrian gneiss. Gangue minerals include chlorite, specular hematite, chalcopyrite, chalcocite, and fluorite. Mineralization is mid-Tertiary in age and has a direct genetic relation to the emplacement of felsic intrusions. Portions of the ore body are unconformably overlain by sedimentary rocks of the Tertiary Santa Fe Formation. The deposit formed during the early stages of extensional tectonism along the eastern edge of the present day Rio Grande rift.

Jan 1, 1994

By R. Mittler

Over 100 saprolite samples from Turkey Hill Gold Mine, Lumpkin County, Georgia, were analyzed (-80 mesh) for As, Au, and Sb. Maximum values are 16.2 ppm As, 7.9 ppm Au, and 29.1 ppm Sb. Results show trace element content of saprolite varies with topography: ridge top samples show a pronounced decrease in Au and Sb, and to a lesser degree in As, whereas, slope and valley samples have anomalous Au and Sb concentrations, with no discernable pattern for As. Statistical analysis shows strong correlation between Au and Sb and none between Au and As. This study will serve as a model for gold exploration in deeply weathered terrains with variable relief.

Jan 1, 1987

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By Yoginder P. Chugh

The mining methods used at many opencast brown coal mines in Poland and the German Democratic Republic are not used in the US to any extent. Using bucketwheel excavators, bucket chain excavators, and mobile conveyor bridges, the mining techniques may offer efficient, economic alternatives for operators in the US. These mining methods were observed during visits to several open-cast brown coal mines in Eastern Europe over the past two years. Some of them may be particularly attractive for the large lignite mines being planned in North Dakota and Texas.

Jan 11, 1980

By Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides: chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 1000 to 150°C. The rate of dissolution of chalcopyrite becomes so rapid under these conditions that the rate of recovery is no longer limited by the rate of chalcopyrite dissolution, but by the degree of exposure and other factors. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, size of sulfide particles, and fraction of sulfide exposed to solution.

Jan 1, 1972

By J. W. Breen

ASARCO Incorporated has upgraded or is in the process of upgrading the Galena mine electrical, pumping, refrigeration, compressed air, ventilation, hoisting and rockburst monitoring systems to allow continued mining and development work on the 1 589-m (5,200-ft.) level and to provide services for projected deeper mining and development. Additionally, a separate lead-silver milling circuit has been added to the silver-copper mill to process lead-silver ore reserves. This paper describes completed and planned improvements made to date on these systems.

Jan 1, 1991

By A. Durnan

Barrick Goldstrike Mines Inc. (Goldstrike) operates a six circuit (train) pressure oxidation plant for the pretreatment of gold bearing sulfide ores. The property is located 27 miles north of Carlin, Nevada. Since the commissioning and start-up of the first circuit in 1990 until the present total plant availabilities have exceeded 90%. The discussion that follows will detail the maintenance practices employed to consistently achieve this goal.

Jan 1, 1994

By P. Jonsén

Understanding mill charge motion is important. In the charge, the centre of gravity is shifted from the rotational centre of the mill system, and its motion is induced by rotation of the mill, while at the same time the charge creates a torque into the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to the motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty to measure in a tumbling mill. Experimental measurements in a lab mill were done for diverse load cases: varying feed materials, mill fillings, mill speeds and pulp liquids. The mill is set up to directly measure the charge-induced torque. The accuracy is good with relative uncertainty smaller than ±2% for relevant load cases. A full three dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill start-up behavior for torque and mill power. This proves that the model is physically correct, and can be used for full-scale mills.

Feb 27, 2013

By Peter N. Calder

The selection of a slope angle for an open pit in rock has often been made without the benefit of a comprehensive engineering study. This is largely due to the fact that the hardware and procedures necessary for such a study have not been available. Recently this situation has been reversed. The application of borehole television and terrestrial photogrammetric devices has made possible the accurate determination of rock joint structure, on which stability calculations can be based. Another important aspect is the evolution of practical methods of conducting in-situ rock joint strength tests.

Jan 1, 1971

By G. B. Amicucci

A Denver Autometrics Particle Size Monitor, PSM-400, was installed at Golden Sunlight Mines, Inc. in October 1988. The PSM-400 measures the grind product's particle size and percent solids. The particle size is used to control grind size by automatically adjusting mill feed rate. The PSM's continuous response to ore changes has improved grind product uniformity and mill throughput. Metallurgical testing has shown the PSM's accuracy to be +/-1 % + 150 µm (100 mesh).

Jan 1, 1991

By P. D. Chamberlin

Agglomeration for the heap leaching of gold and silver ores can be defined as the process of attaching fine ore particles (less than 100 mesh) to coarser particles so the fines are immobilized and uniformly distributed throughout the heap, thus making the heap more porous and uniformly permeable to the flow of a leaching solution. Agglomeration techniques and equipment to be described include drum and disc agglomerators, stockpile and belt agglomeration, and the use of vibrating deck and reverse running conveyors.

Jan 1, 1986

By M. D. Bishop

Early solvent extraction circuits in the uranium industry utilized bona fide kerosenes as diluents for extractant chemicals. These kerosenes were used successfully in the uranium industry; however, at least one plant was destroyed by fire resulting from the use of a low flash point kerosene. Although the term "kerosene" is used throughout the solvent extraction industry, the authors have been unable to find any use of kerosene in copper solvent extraction circuits. A term that is occasionally used with reference to diluents is "metallurgical kerosene." Such a term is unrecognizable in the petroleum industry. Kerosene [or kerosine] is a flammable hydrocarbon mixture that is less volatile than gasoline. It is produced for combustion purposes and may have variable compositions of organic compounds including alkanes, alkenes, alkines, and aromatics. Diluents are constant composition hydrocarbon mixtures developed specifically for use in solvent extraction processes. These products usually have much lower vapor pressures and higher flash points than kerosene. In solvent extraction systems, they typically comprise 70 to 95 v/o percent of the circuit organic. The primary purpose of the diluent is to adjust the extractant concentration to the working range of the operation. The diluent and extractant must be completely soluble or miscible with each other. Secondary diluent effects are to promote transfer kinetics, optimize phase disengagement, and minimize both organic in aqueous and aqueous in organic entrainment.

Jan 1, 1996

By Gregory M. Rumbaugh, Todd Kostecki, Christopher Mark

From 2015 to 2021, five massive pillar collapses occurred at four underground stone mines in the eastern United States. These events resulted in powerful airblasts that damaged mine infrastructure and mobile equipment, seriously injured miners, and disrupted underground travelways. Each of these pillar collapses propagated through the overlying strata, causing a subsidence basin on the surface. Pillar collapses are particularly hazardous for miners because they can occur with little warning and can affect miners that are far from the pillar collapse area. The following case studies show that certain factors may increase the likelihood of a pillar collapse. For instance, each of the five events involved the collapse of at least twelve benched pillars with width-to-height ratios (w/h) of 0.8 or less. This study elaborates on

By D. A. Lowrie

Environmental concerns and increasing mine development costs have created a need for early information on gold recovery from its host environment. The habit, association, and approximate abundance of minerals which contain unacceptable metallic ions which may be released during process of concentration of gold should be identified in exploration drill core. One case of a "clean" gold orebody is described to show that early petrographic studies contributed to a rapid decision to mine a small deposit by open pit and to custom mill the ore in an already restricted effluent environment. A second example describes identification of an undesirable mercury content and resulting action taken.

Jan 1, 1985

By F. F. Peng

Fine Coal Cleaning Processes including froth flotation, aggregative flotation or oil agglomeration, depend upon the wettability of coal particles in the aqueous solution. The wettability of coals of various ranks, hydrocarbon oil treated coals and oil-agglomerates have been measured using film flotation, induction timer, and froth flotation. Various hydrocarbon collector dispersion techniques are used to alter the surface wettability of coal particles. Change in wettability behaviors, measured by flotation responses, due to various ranks with or without of hydrocarbon collector modification are explained in terms of surface chemistry modifications as analyzed by induction time, film flotation as well as DRIFT Spectroscopy. The relationship between the wettability of coals and collector treated coals, and floatability are discussed.

Jan 1, 1993