Search Documents

By H. Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in BOLTs) has been recently developed at McGill University. The device is essentially an alternative to the load cell, it permits the monitoring of bolt axial load in the field. The SAFEBOLT system consists of a portable readout unit, a connecting cable and the SAFEBOLT device, which is installed in the bolt head. The new device can be installed on any industry standard rockbolt or rebar. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electric wires. Pilot tests at two underground Quebec mines were carried out and helped improve the initial design of the device head.

Jan 1, 2002

By J. Drelich

The highly-efficient and economically-feasible technology for bitumen recovery from US oil sands using a water extraction approach was developed at the end of the last century. This water-based bitumen extraction process has been optimized based on observations and analysis of microscopic mechanisms of bitumen release from oil sands and the bitumen transfer to a froth product as well as measurements of interfacial properties of bitumen. The wetting mechanisms that occur in the diluent-assisted water-based processing of US oil sands include bitumen film rupture and recession on sand grains and bitumen transfer to nucleated and injected gas bubbles. These mechanisms are reviewed in this contribution.

Jan 1, 2007

By David E. Thompson, Andrew F. McKown, Herbert H. Einstein, Amr S. Azzouz

INTRODUCTION Design of supports for underground chambers in rock has undergone considerable development. This becomes evident when comparing support dimensions of subway station caverns built in the U.S. over the past fifteen years. The Porter Square Station cavern, which is a part of the Massachusetts Bay Transportation Authority (MBTA) Red Line extension, is the latest in this series. It is approximately 168 m (550 ft) long, 21 m (70 ft) wide, and 14 m (45 ft) high, and has a permanent support of light steel ribs imbedded in a 0.4 m nominal (15 in) shotcrete lining. An extensive construction control instrumentation program made it possible to evaluate the performance of the cavern and its support. This evaluation, which is presented in this paper, was the objective of a research project sponsored by the Urban Mass Transportation Administration (UMTA) and jointly conducted by Haley and Aldrich, and MIT. The actually used design procedure was compared with other approaches, notably procedures based on Finite Element analyses and empirical rock mass classification methods. Support dimensions predicted with all these approaches were compared to the actual support and its performance.

Jan 1, 1983

By P. D. Chamberlain, R. M. Nadkarni, D. J. Kinneberg

Introduction The relationship between precious metal miners and gold refiners has been uneasy over the years. Reasons for this uneasiness and lack of trust include technical factors, economics of scale, and cultural differences. Technical factors take two forms. First, concentrates, precipitates, and sponge produced at the mine site are notoriously difficult to sample. A nonrepresentative sample can be the cause of misunderstanding and distrust. Dote, however, is relatively homogeneous and can be correctly sampled and analyzed with greater reliability. Second, the technology and chemistry of fine gold and silver production is complex and quite different from dote production. Most mining companies are content not to be involved with additional processing steps. From the standpoint of process economies, it is easy to see why miners and refiners are separate groups. Mine location is dictated by the natural occurrence of ore bodies. Heavy capital investment requirements for infrastructure in remote locations usually limits companies to produce the first marketable product from a mine. Beyond that point, the economies of scale and large capital investments for refineries generally dictate that the outputs of several mines be combined to feed a single refinery. The refin¬ing process is so complex that refineries are generally built in larger cities with a skilled labor pool. Therefore, only the largest mines can afford to refine their own output. Lastly, there are cultural differences between the miner and the refiner. The miner, particularly the small gold miner, is by definition a risk taker in a risky business. Refineries, on the other hand, have historically been operated under legal or implied monopolies approved by the government. The government is interested in owning gold, either for currency reasons or because many national mints are major users of gold coins. It is not surprising, then, to find that miners may regard refiners as part of an unresponsive government bureaucracy or, worse, as "city slickers." It is easy for the two groups to distrust each other with these different backgrounds. The interface between miner and refiner does exist and affects nearly all precious metal mining companies and most refineries. This paper discusses the technical and economic aspects of the interface. It points out how both parties can improve the relationship. Technical interface Precious metals selectively dissolve to produce a pregnant solution. They are then recovered from solution by zinc precipitation (Merrill-Crowe process) or by absorption onto activated carbon. This is followed by stripping and electrowinning. At this point, the mining company must decide whether to ship precipitates (or sponge) to refiners or to produce a dote. Some factors the company must consider are the ability to sample precipitates, concentrates or sponge, security of storage, and production rates. An important factor is the incremental cost (capital and operating) of converting precipitates or sponge into dote at the mine. Generally, mines prefer to melt precipitates or sponge to dote to avoid prob¬lems associated with sampling them. There are three types of fur¬naces used by mining operators to melt precipitates to dote. The first and most widely used is a sil¬icon carbide crucible heated ex¬ternally with a gaseous liquid fuel. The crucible is easy to use and slag can be skimmed before pouring dote. This simple system is capable of handling 1 t/a (32,000 oz per year) gold. It could cost as little as $20,000. More complex systems could cost up to $200,000. The second type of furnace is the gas- or propane-fired rever¬beratory furnace. This is usually used only by large-scale opera¬tors in the silver business. Precip¬itates in reverberatory furnaces come in direct contact with the flame. The large volumes of flue gas can carry significant amounts of dust and fume that must be re¬moved from the gas before dis¬charging it to the atmosphere. In the days when the Rand re¬finery in South Africa used reverberatory furnaces, the silver leaving the furnace in the form of vapor and fume was estimated at 2.2% of the total silver charged to the furnace. The gold in the gases was about 0.03% of the gold charged. Most of this silver and gold was recovered in the exhaust gas scrubber system. These scrub¬ber systems can be more costly than the furnace itself.

Jan 10, 1986

By Robert M. Semple, Harvey W. Parker

INTRODUCTION Two promising innovative tunnel support systems are being developed by the Civil Engineering Department of the University of Illinois. One of these is a lining which can be placed by a slipform located immediately behind and contiguous with a tunneling machine. Recent advancements in construction materials appear to provide the breakthrough required to make such a system feasible and practical. The lining material which permits this construction scheme is wire fiber reinforced concrete made with high, very early strength regulated-set cement. Parts I and II of this paper relate to this slipformed liner. Part I discusses the material and equipment required to install the liner. The "Extruded Liner System" (ELS) has been devised to place the lining. This ELS concept is briefly described and a tentative development program is outlined. In Part II, the physical properties and practical construction aspects of the liner material are discussed and a program for structural testing of 10-ft diameter prototype tunnel supports is presented. Part III contains descriptions of improvements to conventional steel-rib tunnel supports. It is shown that square tubular box sections are structurally superior to wide flange sections for complex loading conditions often encountered in rock tunnels. Analytical studies and tests on connections have been performed to evaluate their structural behavior. These are presented along with a program for comparative large-scale tests on horseshoe-shaped frames with a 10-foot span. This research is being conducted by the Department of Civil

Jan 1, 1997

By E. Tulcanaza

M.S. Azun I do not at all agree with the basic points of the author's conclusion. The use of lognormal or normal model to respond to the attribute distribution function should be carefully questioned. If fitting a distribution function of regionalized variables is the main purpose, one may employ one of certain well-known families of distributions, such as Tukey's lambda functions. For instance, the distribution function of gold assay values studied by Krige (Krige, 1978) may fit the lognormal model well, but one should not exclude that the basic idea of using the distribution function of observed data is to have insight of the physical mechanism that gives rise to the regionalized variables. In Applied Geostatistics, there are many examples considering only lognormal or normal model for the distribution function of geostatistical data even if the observed distribution function has more than one mode. Of course, using lognormal or normal model always brings easy computation for the statistical properties of attribute under investigation. Still, I object to adopting any of those models without having any "statistical inference." As seen from the author's paper, lognormal and normal model produce the same average grade (0.746% copper) and almost the same sample variance. Therefore, which model explains the probabilistic behavior of ore deposit is always an important question that should be replied by the geostatistician using not the common sense but the statistical and probabilistic methods. For kriging procedures, such as linear kriging, one should describe either second order stationary properties or bivariate properties of regionalized variables. Second order properties, such as correlogram function or semivariogram function, are the inputs of the so-called kriging equations. Selecting one of any useable models for the observed second order properties, such as spherical model, is not easy since the models are not based on the correlations structure of the regionalized variables. How those models being used in Applied Geostatistics can be distinguished is another important problem. One may develop many fitting models to respond to the observed second order properties of regionalized variables. However, I suggest that the model should be based on the probabilistic behavior of geologic process. The author used spherical model for copper, wolfram, and silver grades from isotropic sector (Fig. 2, 4, 3b) and exponential model for silver grades obtained along raises in isotropic sector (Fig. 3a). It seems that those semivariograms given in Fig. 3b for isotropic sector and Fig. 4 may be described by the random model implying that regionalized variables do belong to renewal process (Azun, 1983). If I knew the total number of data points used in estimation, I may prove that my conclusion is correct. Recalling the test for the first order sample correlogram value, the test procedure is introduced such that the independence is rejected if [ ] where Za/2 is the a/2 percentile of standard normal random variable and N is the total number of samples used in estimation (Azun, 1983). For the other observed semivariogram functions I suggest the author might try to use the so-called "Markovian model" describing not only the correlation structure of regionalized variables, but also the physical mechanism that produces the regionalized variables. The Markovian model for correlogram function is, [ ] The Markovian model for the other second order properties of ReV are also derived. T ve B, in the above equation, show, for example, structural change and mineralizational variation in a considered deposit, respectively (Azun, 1983). In selecting any model, it is not easy to search for the "best" response to the observed second order properties of ReV's. The Markovian model, based on a theoretical understanding of underlying mechanism, gives more information about the occurrence of regionalized variables and respond to all properties. Random model and the so-called hole effect structure can be easily defined as a special form of the Markovian model (Azun, 1983). An estimation of any second order properties of regionalized variables may be computed through (N-1) lag. However, the dependency between the regionalized variables may be deemed to have "died out" after the so-called stationarity width (range). In practice, the estimation is carried out through 25% of the total number samples available. Therefore, the large fluctuations around the zero level and variance for correlogram or covariogram function and semi-variogram function, respectively, cannot be observed. Since the number of pairs involved in the estimation of higher second order properties is small, the estimation variance at those lags is large. There is no need to show higher order estimated second order properties. After using one of any kriging procedure for block estimation, the distribution function of average grades has the same mean as the drilling sample grades but

Jan 3, 1985

By F. Habashi

The changes that took place in China between 1984 and 2004 are remarkable. Visits were made to universities, research institutes, metallurgical industry, and many cultural centers within five trips during this twenty years period. The impressions of these visits are outlined.

Jan 1, 2007

By Hans Janzon, Ernst Buechi

INTRODUCTION The headrace tunnel in Amlach is part of a hydro electric power scheme near the city of Lienz in south west Austria. The project is owned and developed by Tiroler Wasserkraftwerke AG, the regional electrical supply utility. The construction work was divided into seven contracts for the entire scheme. The power output will be 60 MW, this being developed from a head of 370 m and water flows of 20 m3/s. The water will be tapped from the river Drau and lead through a 22 km long headrace on the south side of the Puster valley through the Lienzer Dolomiten mountain range. Contract No. 4, which is a joint venture between Mayreder, Züblin, Strabag, Rella and Innerebner, involves the construction of 13.5 km of the headrace. It was decided to bore this from one single adit, which probably makes it the longest pressure tunnel driven from one side by a TBM. (See Fig. 1.) For the tunnelling an Atlas Copco Jarva MK 12 TBM was chosen. The excavation diameter is 3.90 m, with the final lined diameter being in the range of 3.20 to 3.40 m. The back-up is a 145 m long single track rail system supplied by Mühlhäuser (Germany). Side-tipping cars with a capacity each of 8.2 m were used for removing the muck. One California switch was attached to the back-up after 3,000 m, and a second fixed switch was installed after 8,000 m of boring. 3 m long

Jan 1, 1987

By S. Dessureault, Z. Gavelan

As globalization continues, sustainability and social responsibility has become essential in foreign mining investment. However this global trend and the increasing acceptability toward the globalization process, viability and sustainability are not always achieved. Viability and sustainability of mineral projects is dependant on the social and political environment of the region where the mining venture is located and is based on the interaction between the mining entrepreneurs, national-local government representatives, communities, grass-roots groups and independent civil organizations. These are the organizations, which play the acting roles on the viability of mining projects and are the main source of socio-political risks for the project. Throughout the decision-making process to invest in a mineral project, socio-political risks are quantified using a set of measurable variables. Nevertheless, these risk measures should be dependent on specific industries. Two mineral projects, even in the same mining district, may have significantly different political risk profiles based on their own socio-political variables. This paper describes a methodology that takes into account local social and political variables in defining a project-specific’s political risk profile. This contrasts with more typical political risk measures that focus on the country’s overall risk profile. Mining operations must operate on a local scale necessitating the development measure that considers more local variables.

Jan 1, 2004

By Michelle Lostra, Red Blanchette, Jan Babendererde, Greg Colzani

The City of Portland’s Westside CSO Project is constructing a deep tunnel system to reduce combined sewer overflows (CSO) from entering the Willamette River. Several kilometers of microtunneled pipelines connect the existing system to the new tunnel. The alignments encountered a variety of ground conditions, including fill, manmade obstructions (wood, steel piles, debris), fine-grained to dense coarse-grained materials, cobbles and boulders, all below groundwater. A slurry MTBM convertible to varying diameters, equipped with mix shield capabilities, was selected to cope with the conditions. This paper will discuss access shaft construction,

Jan 1, 2005

By W. Randall, Robert M. Leary

Twin 1250 m (4100 ft.) long highway tunnels through Cumberland Mountain near Middlesboro, Kentucky are planned to be completed in the early 1990's. The tunnels will be excavated in sandstones, limestones, and shales, dipping at 35 to 50 degrees and striking nearly perpendicular to the tunnel alignment. In 1985-86 a pilot tunnel was excavated as a crown drift along the alignment of the southbound tunnel. The benefits of the pilot tunnel in reducing uncertainties for main tunnel construction are discussed. The cost-benefits of the pilot tunnel are examined in view of estimated main tunnel costs.

Jan 1, 1987

By Charles A. Bankston, John C. Rowley, Robert J. Hanold, Joseph W. Neudecker

The basic concepts and processes of soil and rock melting as applied to excavation technology are reviewed. The electrically heated, small diameter prototype penetrator development sequence is presented. Emphasis is placed on the different methods of handling the fluid rock and soil melts and their significance in providing new solutions in hole support and debris handling problems. The refractory materials requirements, penetrator life and electrical heater technology are presented. Consolidating penetrators, which form stable glass-lined holes in low density rocks and soils, require no debris removal and will find applications in horizontal holes for utilities, cables, and pipeline installations. Extruding penetrators are being developed to make holes in dense, hard rocks. Melt is conditioned into a variety of debris forms, i.e., glass rods, pellets or rock wool, selected to match appropriate debris handling systems. Unique use in drilling into very hot rock or magma for geothermal exploration or production wells is projected. Some of the results of laboratory and field tests of these devices are compared with theoretically derived operating performance. Coring-consolidating penetrators for geological sampling in alluvium are projected to larger diameter self-propelled and guided coring devices for prospecting along proposed tunnel alignments. Application to the melting of annular shafts for pipeline support piles in difficult conditions such as permafrost has been scoped. Conceptual design studies of large diameter tunneling equipment have indicated the system contributions and economic aspects of rock melting relative to material comminution, wall and roof support and materials handling.

Jan 1, 1974

By R. Adsero

"A high altitude review of the state of the mining industry provided by a study of multifactor productivity shows a continuation of lower output year on year for the capital and labor inputs applied. The story is sadly similar for both U.S. mining and the Australian mining sector. In fact, according to PwC analysts, the world’s mining equipment productivity has declined 20 percent during the past seven years (Lumley, 2014). Although the reasons for the continuing decline in mining productivity are varied, the need for improvement is clear.The world’s mining industry fleet of more than 400 large draglines moves billions of tons of overburden and ore (phosphate, limestone, etc.) annually. This discussion will review a few of the tools available for improved productivity in dragline operations.Benchmarking equipment performance exposes the possibilitiesIn the September 2013 Mining Engineering cover story Graham Lumley and R. Adsero suggested that analyzing best practice equipment performance from an industrywide database for specific equipment performance improvement goals would be beneficial (Adsero, 2013). Benchmarking equipment performance by normalizing differences and then comparing specific measures of performance will provide a road map to improvement for those following the leaders. For those already performing at best practice levels, a benchmark confirms and bolsters what has already been achieved. As described in the SME February 2014 paper by this author, best practice is the average of the top 10 percent in annual output. Filling performance gaps identified by a comparison to best practice by investigating the details of the why and taking action to change, makes all the difference. This is true for all major mining equipment. Given the large gap between average performance and best practice performance most mining operations can benefit. Best practice performance provides a view of what is possible to the 90 percent majority of mining operations that are performing below the top 10 percent.For dragline mining operations, identifying specific characteristics and practices of leading dragline performance will provide a reference for comparison."

Nov 1, 2016

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,500 tons of ore per day with an average gold grade of 0.34 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, a long-hole stope and cut-and-fill mining methods are used at the deposits which are divided into several mining zones. Cemented rock fill (CRF) is used as the backfill in the open stope. CRF design includes the aggregate design, the ratio of cement and fly ash design, and strengths for the long-hole stope and cut-and-fill. In the aggregate design, the particle size distribution is one of the most influential aggregate characteristics in determining how it will perform as a basic backfill material. Gradation helps determine durability, porosity, cement and water requirements, strength, and shrinkage. To cut the backfill cost, fly ash usually is added into the binder to replace some part of cement. However, adding fly ash can affect the strength of the backfill. The reasonable percentage of fly ash is also important for making a good and low cost backfill. Based on the different mining method, the different backfill with different strength is designed. A systematic quality control procedure for aggregate and backfill is followed. After four yeas application, CRF system in Leeville achieved very good results.

Jan 1, 2011

By Michael J. Lehnen

Slurry diaphragm walls are commonly used as both temporary excavation support walls, and permanent structural walls, for circular shafts and long rectangular structures (such as underground subway stations); however, they are not commonly used for more compact rectangular or square shafts. In these instances, a second wall is typically cast inside the slurry walls to form the permanent structure. This paper discusses the approach used on the Silicon Valley Rapid Transit Project in California to analyze these compact rectangular types of structures for static and seismic loading, and to determine whether or not slurry walls can be confidently used as both the temporary and permanent walls for two tunnel ventilation shafts.

By Laurens de Jonge, Wiebe Boomsma, Rodney Norman, Stanislav Verichev

"Earth provides natural resources, such as fossil fuels and minerals that are vital for human life. As the global demand grows, especially for strategic minerals, commodity prices rapidly rise. Thus there is an identifiable risk of increasing supply shortage for minerals. Hence a major element in a long-term economic strategy must be, to ensure security of supply for these strategic minerals. In this rapidly changing global economic landscape, deep sea mining has gone from a distant possibility to a likely reality within just a decade.Although deep sea minerals extraction was investigated in the 1970’s, it was abandoned because of changing commodity economics, advances in on-land exploration techniques, growing concern on environmental impact, and political and legal aspects with regard to ownership issues. The developmental data from those days, if still available, are not adequate to allow engineering and building of an integral system for extraction of deep sea minerals without additional R&D work. Thus, deep sea mining is yet to attain a Technology Readiness Level (TRL) sufficient to successfully undertake deep sea mining operations, from resource discovery to resource assessment and to resource exploitation [Blue Mining, 2014]."

Sep 1, 2014

By R. E. Chaves

San Martin Mine is an open pit, gold heap leach operation located approximately 70 kilometers from the Honduran capital of Tegucigalpa. Mining operations commenced in 2000 and were completed late in 2007, while heap leaching operations continue. Reclamation was executed concurrently with operations to the extent practical. The area has distinct rainy and dry seasons and closure objectives include: prevention and mitigation of acid rock drainage, sediment and erosion control, and mitigation of visual impacts. Final closure is well underway at San Martin and this paper describes the closure processes conducted to date, problems encountered, and the subsequent lessons learned.

Jan 1, 2009

By J. S. Stachulak

The Diesel Emissions Evaluation Program (DEEP), a research consortium formed in 1997 by Canadian mining companies, labour unions, and provincial and federal government departments, completed its work by mid-2006. This program, in which Vale Inco participated with both direct funding and in-kind contributions, investigated the ability of currently available technology to significantly reduce underground concentrations of diesel particulate matter (DPM) with high efficiency and low maintenance over a long-term period (years of life).While DEEP?s testing showed that engine maintenance is a critical component for lowering DPM, it was clear that reduction of DPM to the very low target levels of ~0.05 mg/m3 was not possible with maintenance alone. The best candidate technology for achieving low DPM levels was particulate filter systems. Furthermore, successful deployment of such systems was highly dependent on removing them from having to rely on human intervention for their regeneration. The search continues within Vale Inco to identify a reliable and rugged system.

Jan 1, 2009

By O. A. Bascur

The lack of integration of mining and metallurgical information with sufficient detail for analysis causes inefficient operation and hence sub-optimal energy and water use. It is difficult to analyze the performance of mining and metallurgical processes without an integrated view of mine transactions, stockpile inventories, process flows and assays. To take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. This paper presents an infrastructure with advanced tools that sift through available data, identify and eliminate gross errors, and transform the data into business information for continuous improvement and optimization. Collaboration is a key component of improving efficiency of energy and water use, and the evolution of Web technology enables collaboration and troubleshooting of plant information to more quickly act on issues to reduce wasteful operation. Keywords: Mine Concentrator Optimization, Real Time Performance Management, Data Unification, Integration of Operational and Business systems, Mass and Energy Balances, Real Time Web Services, Equipment Availability, Efficiency.

Jan 1, 2009

By Joel Darmstadter

The position of the coal industry in America’s fuel and power picture remains one of prime importance. Measured in Btu terms, the industry is the country’s leading energy producer and an important exporter. Foreign coal sales yield annual proceeds of about $4 billion. Coal’s one-fifth share of the nation’s energy consumption is nearly as high as that of natural gas. Coal is the electric utility sector’s principal fuel supplier. It accounts for about55% of the electricity generated at power stations.

Jan 1, 1999