Search Documents

By Robert G. Lundquist

REAM (for Rapid Excavation And Mining) is a method of rock fragmentation by high-velocity projectile impact developed by Physics International Company. This paper reports the results of field testing over the last two years. The success of the method is based on the fact that the amount of rock broken per shot scales nonlinearly with projectile impact energy. Thus, high energy impact yields spectacularly low specific energies for rock breakage. The field work reported used 90- and 105-mm military guns to accelerate 8-1/2 and 10-pound concrete and steel projectiles to velocities of 5000 to 5500 fps. All tests were performed in a competent 25,000 psi granodiorite at Hope Valley, California. During the first year of field testing 26 feet of 13-foot-diameter tunnel were produced with the 105-mm gun. The first 20 feet of this tunnel were line-drilled to aid in producing a stable portal. During the second year the tunnel was extended an additional 29 feet using the 90-mm gun. The 55-foot tunnel was produced by 590 shots. Between 1-1/4 and 1-1/2 tons of granite were broken by each shot. A silenced 90-mm gun was placed underground and the tunnel portal closed with a steel barrier. Overpressures of less than 1 psi were measured on the inside of the barrier, corresponding to an impulse noise of about 170 db. The muck produced was similar to drill and blast muck. Overbreak and ground support problems appeared to be less than with drill and blast. The contour of the tunnel was easily controlled using the 90-mm gun; the tests were also conducted using a 57-mm gun for trimming. Projections indicate that advance rates with REAM will be three to seven times faster than drill and blast, at less than two-thirds the cost. This is based on the development of a fully integrated continuous system and an inexpensive propellant giving a total expendables cost of less than $3 per shot. Other applications of the REAM technology are found in secondary breakage for open pit mining, in drilling large diameter holes, and in underground mining for longwall mining, overhand stoping, and raising.

Jan 1, 1974

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

Disruption in critical minerals supply chains has resulted in the evaluation of various types of mineral deposits for critical minerals potential. Much of the study on critical minerals focuses on occurrence and characterization, but little research has addressed what concentrations of critical minerals in a mineral deposit are required to make an exploration target into an operating mine. Understanding the cut-off grades of ore deposits being actively mined is one criterion to determine if concentrations in an exploration target are high enough. Cut-off grade is defined as the minimum amount of mineral contained in a ton of ore that is sent to the processing plant. Among many factors, cut-off grade depends upon the size and type of the deposit and mining operation, the processing technique, and market prices. This research does not aim to define cut-offs for determining if a mineral deposit is economic. Rather, it defines estimates of concentrations of critical minerals that could be considered good enough for further exploration. For example, ~2% total rare earth oxide (TREO) is the cut-off grade for Mt. Pass carbonatite, but 500 ppm TREO could be an exploration target for coals.

Feb 1, 2025

By J. MCGUIRE, E. J. Haas, B. Demich

Near misses can enhance awareness of the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, the value of these reports and how they influence subsequent actions or controls to reduce on-the-job risks are unclear. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. The analysis provides insight into ways that risk-communication and management programs can be improved to reengage workers and their situational awareness on the job.

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy's program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By C. L. Kosmoski

In recent years, coal mining safety has attained national attention due to several highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with 42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year (National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture,? and can be defined as the characteristics of the work environment (such as the norms, rules, and common understandings) that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to present the aggregated results from those five safety culture assessments conducted at underground coal mines. Additionally, some general recommendations for areas where coal mines might focus their attention as part of their attempts to improve safety culture are offered.

Feb 23, 2014

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes.Water is routed to the roof bolter fromthe main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/ m3, and during the cleaning of the dry box, the average respirable dust concentration was 1.188 mg/m3, a 60% reduction in respirable dust concentration. The quartz content of the roofmaterialwas high, ranging from 28.9 to 52.7%during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60% when cleaning the collector boxes.

Aug 26, 2020

By David Mast, Amanda Foote, Mina Shinouda

The Michigan DOT’s I‑75 Modernization Project, Segment 3, is a 30-year, $1.2 Billion design-build-finance-maintain project in Southeast Michigan. The scope includes building a nearly 4-mile long, 14.5-foot ID stormwater storage tunnel. The tunnel and pump station are being built concurrent with new roads and bridges, requiring multiple levels of design and construction coordination. Underground risks include the poten‑ tial for encountering granular soils, groundwater, and explosive gases. The new tunnel will be mined by a new open-face TBM and lined with a one-pass steel-fiber-reinforced precast concrete segmental lining. Shaft construction began in early 2020 and tunnel mining in July 2020.

Jun 13, 2021

By Jianbo Hu, Gang Han, Tao Zheng, Junfeng Jiang, Rui Su, Qihua Zhao

The rock quality designation (RQD) is a commonly used index for the classification and evaluation of rock mass quality and is widely adopted in mining and geological engineering. The traditional method of obtaining RQD still requires manual measurement of core length and calculation of RQD, which is inefficient. To address this problem, we propose a framework for drilling core image segmentation and RQD estimation from digital images of cores in core boxes based on the deep learning algorithm. The proposed framework is generated by combining the Mask Region-Based Convolutional Neural Networks (Mask R-CNN) instance segmentation algorithm, the U-Shaped Convolutional Neural Networks (U-Net) semantic segmentation algorithm, and the image processing functions of the Open Source Computer Vision Library (OpenCV). To demonstrate the accuracy of the proposed method, seven boreholes in the Xiushuihe vanadium-titanium magnetite mine, located in the Sichuan Province, China, were used as the case study. According to the comparison of the manual measurements and calculations of the cores taken from seven boreholes used to conduct this study, the framework can record the length of the drill cores and calculate RQD within an average error rate of 3.42%, while it saves about 85% of the working time. The results illustrate that the proposed framework enhances the efficiency of RQD calculation while satisfying the engineering requirements.

Jul 31, 2023

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining health and safety of miners. The authors evaluate potential real-time monitoring solutions for detecting and reducing diesel particulatematter, mine fires, and dust in situ, and examined the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limit. Authors review relevant documents, including research papers, trade publications, and manufacturers’ website-based information, to identify research gaps. The authors also evaluate contemporary sensors (airflow, gas, dust, silica), control system and software technologies, data transport systems, Industrial Internet of Things, ventilation network simulators, and control devices to identify potential health and safety research gaps. In this study, examples of some mines from Canada, Australia, and the USA are included where ventilation monitoring and controls have been applied. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

May 12, 2020

By W. C. Hellyer

In an autogenous grinding circuit in which feed at approximately nine inches top size is reduced to a size suitable for subsequent processing, the build- up of a "critical size" fraction in the media causes problems. A "critical size" fraction has been defined as, "media too small to effect reduction by impact grinding of ore coarser than a quarter of an inch and too large to be broken by the largest size of media in the charge. 9, (1) The buildup of a "critical size" fraction reduces the capacity of the mill, increases the grinding power requirements per ton of finished product, and generally produces a finer grind than is desired. It is general practice to overcome this problem by the addition of large diameter steel balls to the grinding charge. This has certain disadvantages, such as; (i) an increase in mill liner wear; (ii) wear on the steel balls, and; (iii) some loss in flexibility in grinding circuit operations resulting from difficulties in removing the steel balls by means other than by grinding out.

Jan 1, 1970

By Thomas E. Finch

Engineering mine design encompasses a range of situations, and each situation has its own range of detail and fineness. The most time consuming, and perhaps repetitive design situation involves evaluation of new or alternate mining methods. Many man years are consumed examing alternatives conjured up at all levels of the design team, from the number crunching engineer to the engineering manager. Many alternatives are intuitively disregarded, some are briefly evaluated and thrown out, and many others are started but not completed due to time constraints. All alternatives have similar input characteristics and evaluation procedures. In the design process, production requirements are known and equipment production capabilities are generated to determine the numbers and costs of an equipment type required to match a given situation. The end result is some comparative figure, typically cost per ton or yard upon which a decision is built. The similarity of input data and problem solving techniques lends design to computer solution. Computer aided equipment evaluation is not new to the mining industry. An existing and accepted technique is exemplified with the programs used by truck manufacturers. Given a haulage profile and production requirements, the number of anyone capacity, horsepower, tire size, gear ratio or similar characteristically identified truck can be determined. This information can be outputted in varying degrees of complexity and the results used with equally varying percentages of credibility by design or production engineers. Most engineers are willing to accept-the computer's effort with relief and a desire for belief. Although inherently more complex, the ultimate end of computer manipulation should be total mine design. This is an extremely large step in the evolution of mine design, and not many engineers, including the authors, believe the results would be directly applicable or necessarily correct. As with computer simulations of an operation, total computer design of mines requires such complex and lengthy input that each mine might be manually designed more quickly and cheaply. The existence of computer programs which initially evaluate a mining system or part of the system is upon us, however.

Jan 1, 1978

By S. Lu, J. P. Barta, T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate : 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3)Azospirillum had no effect on canopy cover.

Jan 1, 1999

By D. Parks, A. Miller, M. McNinch, R. Jacksha, H. Nickerson

Each year hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s implementation of an IoT-based intelligent machine monitoring system to improve safety during operation and maintenance at a concrete batch plant. INTRODUCTION Of the hundreds of machinery-related accidents occurring every year in the mining industry, incidents involving stationary machinery at surface mines continue to be amongst the most frequent [1]. A National Institute for Occupational Safety and Health (NIOSH) study showed that the majority of fatal accidents involving stationary machinery at surface mines occurred at sand and gravel (38%) and stone (26%) operations. Of these accidents, entanglement in conveyor components were the most common cause of fatal accidents (48%) [2]. The same study stated that one-third of these accidents involved improper lockout/tagout (LOTO) procedures as a contributing factor. The U.S. Mine Safety and Health Administration (MSHA) acknowledged this problem, stating in a recent request for information (RFI) [3]: “Since 2007, there have been 17 fatalities related to working near or around belt conveyors, of which 76 percent were related to miners becoming entangled in belt drives, belt rollers, and discharge points. Factors that contribute to entanglement hazards include inadequate or missing guards, inadequate or an insufficient number of crossovers in strategic locations, and/or inappropriate lock out/tag out procedures. Systems that can sense a miner's presence in hazardous locations; ensure that machine guards are properly secured in place; and/or ensure machines are properly locked out and tagged out during maintenance would reduce fatalities [3].” In response to this problem, NIOSH’s Spokane Mining Research Division (SMRD) is exploring the potential application of Internet of Things (IoT) technologies to provide cost-effective intelligent machine monitoring systems for improved worker safety [4, 5]. SMRD partnered with Central Pre-mix CRH Company (Central Pre-mix) to develop and install a proof-of-concept wireless IoT solution to monitor machinery and conveyors during operation and maintenance. The primary goals of the system were to provide real-time monitoring of access points and facilitate the planning and execution of LOTO procedures

Jan 1, 2019

By Albert R. Rule

Beneficiation studies were made by the Bureau of Mines to develop a process for concentrating phosphate minerals from the altered rock of the Phosphoria Formation. This report describes research on intermediate - and marginal-grade ores from southeast Idaho, The process developed consists of attrition scrubbing and sizing to produce a coarse concentrate; desliming at about 800 mesh (18.5 microns); flotation of the fine sands; roasting of the combined concentrates for removal of organic carbon and combined water; and leaching with SO2 for removal of magnesium and nonapatitic calcite. Results of continuous tests on three different ore types showed that approximately 80 percent of the available phosphate can be recovered at a grade suitable for phosphoric acid production. While leaching with SO2 is not necessary for all ore types, it is an important step in purifying concentrates containing excessive magnesium.

Jan 1, 1966

By V. K. Gupta

The experimental results of some wet batch and continuous grinding experiments carried out in a 40 x 40 cm grate discharge ball mill have been analyzed for the variation of the grinding rate parameters, Si, with various operating conditions using a linearized population balance model. The wet grinding tests were carried out under conditions which were very similar to those encountered in the actual practice in plant operation. Well distributed -4 and -20 mesh feeds of two complex pyritic ores were used. The volume-percent solids in the pulp ranged from 30-40, the particle load from 5-8 kg, and the solids feed rate from 70-1 10 kg/hr.

Jan 1, 1981

By Dirk van Zvl

The design of cover systems for reclamation schemes in tailings requires estimation or determination of tailings materials properties such as compressibility, shear strength and consolidation characteristics. It is very difficult and expensive to obtain truly undisturbed tailings samples for laboratory testing. In situ testing methods have been developed for economically obtaining large amounts of information. Two of these methods are described, the piezocone and the flat plate dilatometer. Both of these methods provide a rapid means of detailed material identification in a nearly continuous fashion for the entire depth investigated. The equipment is described and typical data from a uranium tailings impoundment is presented. The results are compared and the advantages and disadvantages of these methods are discussed.

Jan 1, 1984

By Mike Ghassemi

It is clear that precise overground and under-ground mapping is an important factor for all designers. Due to rapid changes in underground construction, tunnel designers are increasingly in need of updating project information. This article explains the latest techniques for detecting under-ground utilities as well as underground mapping. Global Positioning System (GPS) is a very ac-curate and popular navigation and mapping system that has been used extensively above ground, but is not used for underground mapping as signals are not strong enough to pass through ground or water. Most underground techniques were developed for military applications during the first and second world wars. Later, the techniques became public. For example, ground penetrating radar was developed for the military in 1970 to be used for locating tunnels under the demilitarized zone between North and South Korea. Later, the same technique was used for detecting unexploded ordinance such as plastic land mines.

Jan 1, 2011

By Z. Hyder, M. D. Cleason

"INTRODUCTION Mine Ventilation has come a long way over the years. The main purpose of mine ventilation is to keep conditions in the mine safe for the worker so that the mine will be productive and profitable. Technological developments to the mine ventilation system itself and the development of mining techniques have helped improve the safety and productivity of the miners and the mine. Most of the developments to mine ventilation and to safety devices came as the result of serious mining disasters. Another effect of those mining disasters, especially in the late 19th century and after, was legislation to set specific safety standards for mines, especially in the underground coal mines. This paper will focus on the connection between mines disasters and the mine safety legislations promulgated because of those disasters. A BRIEF HISTORY OF MINE SAFETY LEGISLATION Mine legislation has a long history in the U.S. dating back well in the 1800’s. However, mine safety legislation is considerably newer. In 1891, the U.S. Congress passed the very first version of mine safety legislations setting up minimum safety standards. By today’s standards, the 1891 legislation was incredibly basic (7). It took a series of horrific mining disasters for Congress to take action a second time. In 1910, Congress established the Bureau of mines. The role of Bureau developed and changed over next 60 years. In 1995, Congress voted to disband it (27). Initially the Bureau was only charged with investigating and coming up with ways to reduce accidents in coal mines. It was not until 1941, when Congress formally allowed Bureau of Mines’ Inspectors into the mines. In 1947, the Congress enacted and adopted a set of federal safety regulations for the inspectors to follow (1). Finally, in 1952 Congress granted the Bureau of Mines the authority to inspect the mines and to issue citations and/or orders of withdrawals. This act was known as the 1952 Coal Act and the penalties were limited to civil penalties. It would take a couple more iterations of mine safety legislation for monetary and criminal penalties to be introduced (10). Up until 1966, mine safety legislation was directed primarily at underground coal mines and surface coal mines. Congress passed the Federal Metal and Nonmetallic Mine Safety Act of 1966, thus providing a set of standards for all mines to follow (1). The 1952 Coal Act was amended again to be the Federal Coal Mine Health and Safety Act of 1969. This amendment was the beginning of modern mine safety legislation (13). In 1973, Congress created what can be considered the first ‘version’ of the modern day MSHA (Mine Safety and Health Administration). The initial version was the Mining Enforcement and Safety Administrations or MESA. Congress created MESA to act as the enforcement agency, relieving the Bureau of Mines of that responsibility so they could focus on their initial purpose, the development of countries natural resources (14). As mining industry grew, mine safety and health became a greater concern and priority. More efforts were put in legislating the industry. The Federal Mine Safety and Health Act of 1977 provided the platform for today’s mine safety and health legislation. Under the Federal Mine Safety and Health Act of 1977, also known as the Mine Act, MSHA came into being (1)."

Jan 1, 2016

By David Wright, Jerome Chamfray, Anthony Harding, Brian Boye

Conway’s Law states that unless we intentionally design automation tools around what we need, we will simply replicate our existing processes. While we may achieve some savings this way, there is an opportunity for greater benefits if we re-imagine the way we, as an industry, perform design. This paper examines current technology and shows how even small departures from merely encoding what we currently do could reap significant benefits. From these examples a framework is developed for a new and innovative approach tvo automation that will allow us to design more quickly, to a higher quality, and communicate outcomes more effectively.

Dec 1, 2022