Search Documents

By S. Jayson Ripke, Shane Hoff

Cleveland-Cliffs’ Northshore Mining Company operates a magnetic iron ore (taconite) concentrator and pelletizer in Silver Bay, MN. These are two recent cost reduction projects: 1. Rougher Magnetic Separators were upgraded throughout the concentrator; throughput and recovery were simultaneously improved. 2. Green Ball Roll Screens on one agglomeration circuit were upgraded from 3.5-inch to 2.5-inch rolls. Throughput improved by 24% from 62 to 77 LTPH. Green ball size distribution improved as an added benefit.

Jan 1, 2005

By S. Coats, G. Norton, A. Benham, P. Ková

The Aynak copper deposit, located 30 km south of Kabul in Afghanistan (Figure 1), was discovered by Soviet geologists in the 1970s. Extensive exploration undertaken in the area between 1974-80 included several hundred boreholes, seventy trenches and nine exploratory adits. This work identified a “drill-indicated resource” of 240 Mt at 2.3% Cu (ESCAP, 1995).

Jan 1, 2007

By E. C. Robertson

D.G. Wilder I found the suggestion that the amount of displacement of a fault can be numerically related to the thickness of gouge or breccia to be both intuitively satisfying and intriguing. I have long agreed that there is some type of relationship between the amount of gouge and the amount of displacement of faults. I congratulate the author for developing a numerical relationship between them. However, I am concerned that the limits for applying this relationship be fully understood. An underlying assumption in this approach is that there is either a uniform thickness of gouge or breccia along a given fault or the thickness does not vary widely. Since it is not always possible to confirm this, the displacements derived by this method should be viewed with caution unless significant fault extent can be observed. At the Nevada Test Site, in drifts constructed in granite for test emplacement of spent nuclear reactor fuel, we found a fault with 0.3 to 0.4 m (12 to 16 in.) of clay gouge. Within a few meters of this location, the fault had no clay gouge, but rather consisted of a highly fractured zone with significantly altered rock and some slickensides. Based on Fig. 1, the 0.3 to 0.4 m (12 to 16 in.) thickness of gouge would indicate a displacement in excess of 30 m (98 ft). However, no gouge thickness would indicate essentially no displacement. Based on a quartz vein that terminated on the fault, and is not identified nearby, an estimated displacement of more than a few meters was made. This estimate is consistent with that obtained using the regression line proposed in the paper if the 0.3 to 0.4 m (12 to 16 in.) thickness for the gouge is used. However, using the regression curves with zero thickness would not yield results consistent with what was observed in the field. Therefore, it is important to recognize that the suggested procedure would properly yield a range of probable displacements. ? *Work performed under the auspices of the US Department of Energy by the Lawrence Livermore National Laboratory under Contract W-7405-Eng-48. Reply by E.C. Robertson It is certainly true that the t (thickness) of gg-bx (gouge and breccia) on a fault does vary along the fault. My observations have been that near the termination of a fault, the displacement d is small and the t is also small, whereas the maximum d and t will usually be found in the central part of the fault. The information on gg-bx and t of the fault found in granite in the NTS tunnel by Mr. Wilder could be interpreted somewhat differently than he does. He speaks of the fault changing within a few meters from 0.3 to 0.4 m (12 to 16 in.) of clay gg to "a highly fractured zone with significantly altered rock and some slickensides," but no gg. The highly fractured rock may be taken to be bx, rock not so finely ground as gg but still crushed by the fault movement, equivalent to the gg in my usage, and probably occupying about the same t. Mr. Wilder's estimates for the fault in the NTS tunnel for t of 0.3 to 0.4 m (12 to 16 in.) and for d of a quartz vein, in excess of "a few meters," would place the point on the low side of the central trend line in my Fig. 1, at the lower limit. There is, of course, a problem with determining d using displacement of only one planar surface. It would be greater or lesser depending on the rake of the movement. Finally, estimating the d of a fault from its t should be made with awareness of our present uncertainties, as pointed out by Mr. Wilder. Although the central trend line in my Fig. 1 has a ratio of d/t of 100, I have put the limiting ratios at 10 and 1000. Understanding of the values of the ratio will be improved only with collection of more data, for which the discussion of Mr. Wilder is much appreciated. G.C. Waterman E.C. Robertson's paper provides significant information to a geologist attempting to deduce fault offset by noting the products of structural dislocation. However, considerable mapping in underground and open-pit mines, and examination of structures produced in different geological settings, have convinced me that gouge and breccia thickness are controlled by geological conditions and fault movement. The following paragraphs suggest geological variables that control them. 1. Depth of Loading A near-surface fault resulting from tensional stress has more breccia/gouge than is produced by a similar stress at considerable depth. A deep-loaded compressional stress may produce a linear zone of schist, or structural dislocation may occur along an earlier formed belt of schist. Such "shear zones" are common in Canadian mines in precambrian rocks. In neither case can offset be directly deduced by an analysis of the minimal gouge/breccia in the shistose rocks. At greater depth, stress may be partially to wholly relieved by flowage. I vividly recall first noting the regional "Midas Thrust" in the Lark mine, Bingham Mining District, UT (where we called the structure the North Fault). My recorded notes, as I remember them, showed a narrow gouge streak separated the `Jordan" and "Commercial" limestone units from impure, muddy limestone beds of uncertain stratigraphic position. The visible structure did not indicate the great importance of this premineral fault

Jan 12, 1984

By James W. Stewart, A. C. Colvine

Introduction Precambrian shield terrains the world over are experiencing an unprecedented level of concerted exploration for lode gold deposits. Reasons for this include: • The increase in the price of gold (following 40 years at $1.13/g or $35 per oz) has transformed targets that were once unattractive into viable exploration propositions. • The relatively suppressed market for other metals produced from shields (base metals, nickel, iron, and uranium) has further focused exploration attention on gold. • The preeminence of gold production from rocks of early Precambrian age, as shown in Fig. 1. • The relatively high grade of gold in these mines (averaging about 10 Wt or 0.29 oz per st) permits profitable extraction even under depressed gold prices. A number of these mines have been in continuous operation for more than 50 years. • The recent discovery of the major Hemlo deposit, in well exposed rocks adjacent to the Trans Canada Highway, has had a world-wide impact. This demonstrates that a major new deposit can be found even in an accessible, well exposed area of a shield; gold mineralization is susceptible to rational exploration; and new target types for gold exploration exist. This paper reviews exploration activity for gold in shield terrains worldwide (Fig. 2), excluding Early Proterozoic paleoplacers of the Witwatersrand type. Emphasis is on the Archean, which is traditionally the most productive part of the Precambrian shields. There is also an emphasis on the Canadian shield (Fig. 3) because of its vast areal extent and exceptionally broad range of mineralization styles. Geological Approach A basic problem exists in gold exploration when compared to exploration for base metal massive sulfides that predominated during the 1960s and 1970s. Gold concentrations cannot usually be detected by airborne geophysical instruments. The majority of massive sulfide deposits were detected using airborne electromagnetic detectors and magnetometers. A full 75% of Canadian gold discoveries can be credited to surface prospecting. The percentage is even higher in other countries. This observation allows for great optimism for two reasons: • Large areas of shield terrain are obscured by either surficial deposits (glacial tills, clays, and desert sands) or deep surface weathering. This makes them inaccessible to prospectors. Logic dictates that such obscured areas should have the same potential for gold concentration as has exposed bedrock. • The Hemlo style of mineralization, a roughly tabular ore body where gold is associated with disseminated sulfides, is different from the traditional prospecting target. The gold is hosted by discrete quartz veins. While it is true that limited discoveries were made at Hemlo more than 30 years ago, and this style of mineralization is present elsewhere, recent

Jan 12, 1984

Narrow vein mining, with enough challenge and also where the cutting edge technology can be applied, is still a very important and exciting portion of the mining industry. Based on the deposit characteristics, the most flexible mining method, cut and fill, has been being tested mining this high grade Northern Nevada property, Hollister, since the year of 2008. In the last three years, 254,000 tons of ore were hauled out of the portal and 23,000 feet of development were excavated underground with the winning of several safety and environmental awards. Together with mine geology, the essential segments include mining cycle, ground control, ventilation, grade control and backfill method in cut and fill stopes were covered in this paper.

Jan 1, 2012

Column flotation has been successfully implemented on a production scale in the Athabasca oil sands. In this application, bitumen is recovered and mineral matter is simultaneously rejected from a middling stream originating from a primary separation vessel. Exploiting the natural hydrophobicity of bitumen, the middlings streams have traditionally been processed utilizing conventional, mechanical flotation cells. Although these cells offer adequate bitumen recovery and mineral rejection rates, operating costs are high due to the required maintenance of the wetted mechanical components. In comparison, column flotation provides superior metallurgical performance while offering a lower maintenance demand. Both metallurgical and mechanical characteristics of column flotation are discussed to demonstrate the benefits of this technology for the recovery of bitumen from oil sands.

Jan 1, 2012

By Robin J. Batterham

We still need to innovate, but it is getting harder. The real price of metals is declining, return on shareholder value is lower than other industries, and there is a shorter-term focus on staying viable in a capital-intensive industry where timeframes for implementation of new technologies can be long (+I5 years). In this environment, the levels of R&D spent by major minerals companies are remaining steady at around 0.2%-0.5% of revenue. This is not large and to remain viable in the future, we need to be smarter about the way in which we do R&D. The mining industry is a knowledge-based industry. Driving down the cost curve demands innovation, which demands knowledge. To be smarter and more effective in our approach to innovation, a new paradigm is required Generating, capturing and using knowledge has evolved from Mode 1 (discipline based and clear distinction between basic and applied research) to Mode 2 (multidisciplinary, team-based approached with flow between basic and applied activities). Mode 2 is now seen to be much more efficient and to deliver better appropriability (Tegart 2003). To survive, we need to innovate, and the best way to do this is collaboratively. Some examples and pointers for the future will be given in this paper. THE CURRENT SITUATION The Rand report and other recent studies have painted a grim outlook for the mining industry. The real price of metals continues to decline (Figure 1) and profit margins remain thin. This is reflected in shareholder returnwhich are well below other industries (Figure 2)-and current management strategies-which reflect something of a "survival mode." The current focus for most mining companies is on short-term, incremental gains

Jan 1, 2004

By Andrew Kaczmarek

The mining industry is enjoying a much needed and long awaited increase in demand for natural resources. However, consolidations in the mining and mining service industries, along with a generational departure of experienced industry professionals, is challenging today’s mining companies. These challenges are not only in maintaining their existing operations, but also in securing qualified resources for developing new projects. These challenges are compounded for junior mining companies. They oftentimes lack for operating properties to draw experienced professionals from. Also, juniors have to compete with the majors’ “mega-projects” for experienced project personnel from the reduced ranks of engineering companies. This article discusses some strategies developed by Anatolia Minerals Development (Anatolia) in developing its Çöpler gold project in central Turkey.

Jan 1, 2006

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By N. P. Widodo

The ventilation measurements by tracer gas method at Pongkor gold mine show that effective diffusion coefficient, E, at straight airways indicated a similar range of measured one by the laboratory experiments which can be estimated by Taylor equation. On the other hand, E of the curved airways in the mine was estimated as larger than that of the straight ones (1.5 to 32 times than that obtained by the Taylor equation and these have been compared with the data measured in Kushiro coal mine, Japan). The curved mine airways, with small curvature against airway radius and complex velocity profile, possibly give concentration ? time curves with long tailings, thus those airway conditions could make larger E. Laboratory experiments of gas diffusion by a pulsed injection of small amount gas, into straight and curved airways, have been conducted in order to investigate a range of E in mine airways. The plots of E against Reynolds number show that the present laboratory results of straight-long airways are almost close to one calculated by Taylor equation. On the other hand, the values of E measured at curved single-direction airways were smaller than that of the straight airways, which may be due to effects by secondary vortexes flow in the curved airways.

Jan 1, 2009

By Steve Kral

Improved metals and other commodity prices have caused the mining industry to open new mines, re-evaluate development opportunities at potential mines and increase production at existing ones. This sense of renewed optimism is being seen at operations and development projects around the world. Except in the United States. The regulatory structure there has not allowed the domestic industry to share much in mining’s resurgence. It can still take up to 10 years to permit a new mine. And, while Clinton-era regulations regarding mill sites have been put on hold, existing mines that wish to expand operations still face significant regulatory and environmental hurdles. But things may begin to improve in the United States.

Jan 1, 2005

By J. C. Schneider, G. Van Weert

Hydrochem Developments Ltd. has developed and put into full scale operation a novel type of vertical flotation column incorporating a multiplicity of mechanically agitated stages. Characteristics of this flotation column include a low height to diameter ratio, high upgrading factors and the possibility of modifying geometry and operation to specific flotation requirements. A commercial unit is currently handling up to 100 tpd rougher concentrate at Dickenson Mines Limited, Balmertown, Ontario. Design parameters and plant performance will be discussed.

Jan 1, 1988

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which makes completely new designs of shell and tube configurations possible. Further, self-cleaning fluidized bed heat exchangers show a strong shear thinning effect in non-Newtonian liquids. All the above characteristics make the self-cleaning fluidized bed heat exchanger an ideal tool for the indirect heating of laterite nickel slurry in High-Pressure-Acid-Leach (HPAL) plants. Preliminary tests and evaluations of these heat exchangers have shown that the performance and price of these heat exchangers used for the production of nickel and cobalt from a laterite slurry, cannot be matched by existing conventional heat exchange systems. This article explains the principle, design, lay-out and enormous advantages of the self-cleaning fluidized bed heat exchange technology in a plant suitable for an annual production of approx. 45,000 ton nickel and 4,500 ton cobalt from laterite slurry through high pressure'acid leaching.

Jan 1, 2002

By Wern-ping Chen

To mitigate and control the combined sewer over-flows from 17 outfalls in Detroit, MI, three outfalls in Dearborn Heights, MI and eight outfalls in Redford Township MI, the Detroit Water and Sewerage Department (DWSD) completed the preliminary design of a storage tunnel in 2005. In 2006, a final design revised the alignments and the inside diameter (ID) of the tunnel. The revised tunnel system includes an 11.28-km (7-mile) 9.14-m (30-ft) ID tunnel, a 24.4-m (80-ft) ID pump station, two work shafts about 15.2-m (50-ft) ID each and 14 drop shafts with various IDs. A small portion of combined sanitary and storm sewers serve the majority of the Rouge Valley water-shed. This includes Detroit, MI and most of the western suburbs. The Northwest Interceptor (NWI), that extends between Eight Mile Road and Ford Road and roughly parallel to the Rouge River, intercepts sanitary sewage and some wet weather flows from trunk sewers in the tributary areas for transport to the wastewater treatment plant (WWTP) for treatment. During extreme storm events, when the capacity of the NWI is exceeded, the excess combined sewer and overflow (CSO) over-flows into the Rouge River through 17 outfalls to local rivers. The purpose of the Upper Rouge Tunnel system (URT) is to capture and significantly reduce the uncontrolled CSO from these 17 outfalls in Detroit, three outfalls in Dearborn Heights and eight outfalls in Redford Township. When implemented, the

Jan 1, 2007

By A. B. Cecala

Over the past decade, a substantial effort has been made to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment to reduce respirable dust exposures to the equipment operators. As part of this effort, the National Institute for Occupational Safety and Health, (NIOSH) completed a comprehensive laboratory study which determined the significant factors for cab filtration and pressurization systems. From this information, a major underground mining equipment manufacturer designed a filtration and pressurization system which was incorporated into the enclosed cabs of its equipment. A long-term evaluation was performed on the effectiveness of this filtration and pressurization system to improve the air quality in the enclosed cabs of two different pieces of equipment, being a face drill and a roof-bolter machine, at an underground limestone mine. This long-term evaluation demonstrated a significant reduction in dust levels comparing outside to inside cab respirable dust concentrations. During this evaluation, a modification to remove one of the filters on the roof-bolter machine simplified the design without sacrificing the system?s efficiency. Testing using particle count instruments performed during non-production time periods on both pieces of equipment indicated Protection Factors greater than 100 when comparing respirable-sized dust particles inside the enclosed cab relative to outside.

Jan 1, 2012

By Franz Walchshofer, Mark Kuchta, Nobuharu Isago, Ugur Ozbay, Wolfgang Dolsak

A series of in situ pull test were performed on a new design friction stabilizer bolt with the objective of determining its performance characteristics. The bolt is installed while drilling, thus improving safety and significantly reducing the installation time. An optional expansion element can be inserted into the bolt to provide an end-anchorage, which further increases the bolt’s capacity. In situ tests show that the pull capacity of the 2 m long new design bolt is about 15 tons. When installed with an expansion element, the pull capacity of these bolts becomes as high as 30 tons.

Jan 1, 2005

By H. Do, R. Yoon

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 to 100 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2007

By Tim Q. Haldane

The ability to efficiently process lowgrade ores has allowed the Gold Fields Mesquite Mine in Imperial County, CA to expand from a 2.1 Mt/a (2.3 million stpy) rate in 1986 to its present 7.3 Mt/ a (8 million stpy) processing rate. Increased tonnage demands led to the 1989 construction and startup of a dump leach pad to supplement the existing heap leach operation. This resulted in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. Gold Fields' Mesquite Mine is a gold heap leach facility located about 55 km (35 miles) east of Brawley in southeastern California. Five open-pit mines will be developed over the projected life of the property, covering a total area extending to a maximum of 5.5 km (3.4 miles) to the east and west, and 2.4 kin (1.5 miles) to the north and south. Mesquite will process 7.3 Mt (8 million st) of ore and produce more than 6.2 t (200 000 oz) of gold in 1990.

Jan 1, 1990

By Paul D. Tomlingson

There are huge benefits for mining operations that have a well-defined maintenance program that is understood and followed across the total operation. But for operations lacking a quality maintenance program, there is equal assurance that nearly every major maintenance problem can be traced to this omission. Few problems will be permanently corrected until such a program is implemented. Definition The maintenance program re-quires the interaction of all mine departments. Initially, the production department will request work and the maintenance department will identify work, principally through preventive maintenance inspection and testing efforts. Maintenance will then classify the new work to determine the best way to respond. Maintenance will plan selected major jobs to enable its crews to carry them out more effectively. Maintenance will schedule the planned work with operations. Supervisors will assign all types of work to their crews then, control the work through effective supervision. As work is completed, maintenance will measure the work using an accurate information system. Next, it will assess overall accomplishments against goals such as performance standards or budgets. In addition, the pro-gram would prescribe a means to evaluate every aspect of the operation as it affects maintenance so that necessary improvements or changes can be identified, prioritized and acted on. Such evaluations should be part of a mine-wide continuous improvement effort. A well-defined maintenance program is one of the best investments a mining operation can make to assure its profitability. Educating the total operation on the pro-gram assures long-term dividends from the investment.

Jan 1, 2008

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003