Search Documents

By Frank J. Foster

This Paper will deal with Bucketwheel Suction Dredging and its particular relationship to mining applications. There will be comparisons with other methods of suction dredging and descriptions of two recent bucketwheel installations in the mining area. The Directory of World Dredging Fleets published in the `larch 1984 edition of World Dredging magazine shows that there are about 1.000 conventional Cutterhead Dredges listed throughout the world with 289 in the United States. There are 242 Bucketline Dredges listed throughout the world of which only 6 are in the United States. These figures are not completely accurate because several units are known to the author that are not on the list and, of course, there may be others.

Jan 1, 1984

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata

"Rock tunnels suffered severe damage from recent large earthquakes in Japan, despite the empirical knowledge that tunnels tolerate earthquakes better than surface structures. Seismic design for rock tunnels have therefore become a fascinating subject for many tunnel engineers. However, even basic behavior, including deformation mode and loading magnitude for hard-rock TBM tunnels and conventional ones during earthquake, has not been fully understood due to lack of actual seismic data; while EPB and slurry TBM tunnels take account of seismic design in Japan if needed. This study conducted a dynamic measurement in an actual road tunnel constructed in rock. The strongest aftershock of “the 2011 off the Pacific coast of Tohoku Earthquake” (Mw = 7.1) occurred during the measurement, providing precious data to examine deformation mode of the tunnel. Considering the acquired data, numerical analysis was also performed to calculate loading magnitude to cause fatal fracture of tunnel lining during earthquake.INTRODUCTIONLarge earthquakes can pose serious risks even for rock tunnels, as evidenced by large earthquakes in the past. In the large earthquake in Japan in 2004 (Mw = 6.6), some tunnels suffered severe damage including collapse of their permanent lining (Mashimo 2005), even though the tunnels were constructed in ordinary ground conditions except for fault, fracture zone, portal area, etc. To mitigate such risks, mechanical behavior of tunnel lining during earthquake should be clarified; however, even basic mechanical behavior including load-bearing capacity of the tunnel lining against earthquake is not fully understood.Numerous damage modes were actually observed due to various ground conditions (eg. Wang et al. 2001; Mashimo 2005). Among them, major tunnel damage caused by earthquakes can be grouped into three main modes as shown in Figure 1, excluding extremely unusual conditions such as a tunnel located on a stratum boundary where the stratum stiffness varies significantly. TYPE-I shows flexural failure or crack by bending moment at shoulders; TYPE-II indicates compression failure or flexural compression failure at crown; and TYPE-III illustrates compression failure at sidewall, mainly observed on tunnel that was constructed using steel ribs and lagging method. These damage modes, Type-I, II and III, are predominantly caused by shearing, horizontal compressing and vertical compressing deformations of the surrounding ground, respectively (Kusaka et al. 2011; Asakura et al. 2001)."

Jan 1, 2016

By Robert Blair, David L. Fey, Stanley E. Church

Determination of the pre-mining geochemical baseline in bed sediments in watersheds impacted by historical mining activity is important in establishing watershed restoration goals. We have developed methods to solve this problem in the Animas River watershed, southwestern Colorado, using geomorphologic mapping to identify terraces that contain pre-mining sediments. Following a systematic evaluation of possible sites, we collected samples of pre-mining sediments in gravel deposits from 21 sites throughout the watershed. Geochemical analysis of individual layers has produced a chemical stratigraphy that can be tied to the historical record through geochronological and dendochronological studies. Analysis of geochemical data, when coupled with the historical record, clearly shows that there has been a major impact on the geochemistry in bed sediments in the active stream channel by past mining activities. Historical mining has resulted in a substantial increase in metals in the very fine sand to clay-sized component of the bed sediment of the upper Animas River, and Cement and Mineral Creeks, which are the major tributaries of the Animas River. Enrichment factors for metals in modem bed sediments, relative to the pre-mining sediments, range from 1 to 6 for arsenic, 1 to more than 10 for cadmium, 1 to about 15 for copper, 1 to more than 25 for lead, 1 to more than 10 for silver, and 1.6 to more than 12 for zinc. The pre-mining bed sediment geochemical baseline is high relative to average crustal abundance values of many metals. The Animas River watershed above Silverton, Colorado would be readily identified as a highly mineralized area suitable for mineral exploration if it were not disturbed by mining.

Jan 1, 2000

By G. M. Smith

Several significant past and present producers of high grade and bulk tonnage gold ore from southeastern California and southwestern Arizona can be empirically and genetically linked to regional peraluminous magmatism which occurred during the late Cretaceous and early Tertiary. Geological relationships and geochemical characteristics from the Fortuna Mine area will be described and compared to those of the Tumco Mines area. Each of these historical gold producers is viewed as a morphologic end member in otherwise genetically linked metallogeny. Cold-quartz veins at Fortuna can be directly linked to peraluminous pegmatites both physically and mineralogically. Silica-magnetite±spidote±garnet rock which occurs as relatively barren, discontinuous, foliation- parallel horizons at Fortuna, but as high grade gold ore at Tumco, is interpreted as replacement of calcareous units during the same episode of peraluminous magnatism responsible for the gold vein mineralization. Whole rock and trace element data from pagmatites and aplites of the Fortuna and Tumco areas, together with data from the Gunnery Range batholith of southwestern Arizona, indicate that the magma series (after Keith, 1984) responsible for the gold metallogeny is peraluminous calcic, and is quite rich in sodium.

Jan 1, 1987

By K. M. O’Connor

Time Domain Reflectometry (TDR) is a pulse testing technique developed by the telecommunications and power industry for use in locating breaks in cables. Variations of this principle have been utilized in applications pertinent to closure and reclamation of coal operations. This paper focuses on applications of TDR technology in the mining industry including monitoring of slope movement, abandoned mine subsidence, ground water levels and subsurface LNAPLs, landfill cover performance, and consolidation of mine tailings. TDR technology has been particularly effective for remote automated monitoring, and alarm systems have been implemented for monitoring subsidence.

Jan 1, 2003

By J. V. Calara, J. D. Miller

The sign of the surface potential for complex non-reactive ionic solids cannot be predicted solely from consideration of the hydration energy of gaseous ions which constitute the ionic lattice. Accurate analysis of these systems must involve the hydration energy of surface ions, which requires knowledge of the crystal structure, the identification of cleavage planes, and the calculation of binding energies of surface ions. Surface binding energies for ionic solids can be deter- mined if the Surface Madelung Constant is known. A computational technique was developed for the calculation of Madelung Constants for infinite lattices which gives excellent agreement with the values calculated by other more complicated methods reported in the literature. Extension of this technique permits the calculation of Surface Madelung Constants and binding energies of surface ions, ?Us, for semi-infinite solids. The hydration free energy of gaseous Ions, ?Fh, together with the calculated binding energy of surface ions, ?Us, allows calculation of the hydration energy of surface ions, ?Gh, as for the case of the ionic solid, MX:

Jan 1, 1976

By Anthony G. Fonseca

The acid leach-solvent extraction processing of oxide copper ores can be improved when selected cation additives are utilized. Bench scale testing showed improvements in both sulfuric acid leaching and solvent extraction processing. Treatment with the method to be described shows improvement in copper recovery in the acid leaching section as well as reduced acid consumption and reduced iron and aluminum dissolution. Processing the copper bearing leach solution with LIX-64N shows increased loading of the LIX reagent which relates to reduced aqueous and organic flow rates, reduced organic loss and inventory as well as a reduction in the size of mixer-settlers. The use of selected monovalent cations controls fluctuations within the pro- cessing system to accomplish the above named improvements. Additionally, these cations are totally compatible throughout the processing system and are quite inexpensive. Bench scale recycle data will be presented both for the leaching section and the continuous solvent extraction processing section up to (but not including) processing the loaded electrolyte. Material balances as well as major solution component monitoring will also be presented.

Jan 1, 1975

By Richard L. Bullock

INTRODUCTION TO COAL MINE PRACTICES To illustrate the trends and the proportions of the various methods used to mine coal underground, Fig. 1 is useful. However, of all the underground coal mining practices in the US, room-and-pillar mining still accounts for 96.5%. This percentage is divided as follows: conventional, machine cut-33.0%; conventional, hand cut -1.7% : and continuous mining-61 .8%. As was stated in Sec. 1, Chap. 7, the term "development" means different things to a coal miner and a metal miner. Though some of the ideas and concepts presented in the first two chapters of this section are valid for all types of mines, they apply particularly to mines using noncoal methods. In coal mines (and many other mines using coal mining systems) development refers to that phase of the mining cycle which advances several entries through the virgin seam, forming pillars by cross- cutting between the parallel entries. Because in the past, coal seams (as well as seams of potash, trona, oil shales, gilsonite, salt, and some uranium) have been much more uniform in their thickness, continuity, and quality, and because they often cover large areas, it has been possible to develop the room-and-pillar mine completely from a preplanned, systematic approach with a minimum of surface drilling information. As the better coal seams of the midwest and east are being depleted (or eliminated because of high sulfur), seams of poor quality and continuity will have to be mined. Also, seams that are not nearly so well known at greater depth will have to be taken as well as some of the steeply pitching and folded seams of the west. The American coal miner is only now feeling the need to do a much more complete job of prospecting the geology of the coal seams than he has ever done before. This is the only way that the risk of unknown rock conditions can be minimized. In many ways, surprises in the rock or coal seams are much more of a disaster to the coal miner developing a room-and- pillar mine than to his metal mining counterpart. Be- cause of the multiple entries, the complex set of the Federal Coal Mine Health and Safety regulations, and the totally dedicated design of coal mining equipment, coal mining systems do not have the flexibility to easily overcome changes in the seams mined or the rocks around them. Thus, if a wide parting of rock shows up unexpectedly in the middle of a coal seam entry being milled away by a continuous miner, it will either have to slowly "chew" through it, convert to a conventional mining system, or stop that particular entry. Likewise, if suddenly the coal disappears completely and in its place are the remains of an old creek bed, the "want" or "wash out" as it's called will usually have to be mined right along with the coal, by the same methods and with the same soft rock equipment, or the entry will have to be abandoned. For reasons such as these, coal seams today should be drilled from the surface just as thoroughly as the ore bodies in metal mines. Having once determined a more precise location of where the coal seams are located and which are suitable for mining, the engineer must still take a systematic approach to planning the mine as completely as possible. The initial series of entries must be planned to be driven either from the side hill portal or from the bottom of the shaft or slope. In either case, they should usually intersect the area close to the midpoint of the mass to be mined.

Jan 1, 1982

By Carlos Kovacs-Figueroa

Because of air pollution control regulations in the early 701s it became necessary to clean effluent gases from the Morenci Reduction Works Smelter. Feasibility studies indicated that this could be accomplished most efficiently by using the smelter gaseous effluent to feed a sulfuric acid plant. Complying with air pollution control regulations thus created the need to dispose of relatively large amounts of concentrated sulfuric acid. Typical Morenci ores contain substantial amounts of oxidized copper minerals which are not recoverable by flotation. In addition, there is low sulfide, high oxide material which can be leached, but is not suitable for flotation concentration. Early in 1971 sufficent data had been accumulated to show that a leaching plant for the Morenci tailings could use a large portion of the sulfuric acid produced by the Smelter. It was determined that for all practical purposes leaching of the available copper was complete in two hours or less. Capital expenditures could not be justified for more than two stages of counter current decantation for recovery of the leached copper, and the plant was designed with these criteria in mind.

Jan 1, 1976

By R. L. Michalowski

The operation of mobile mining equipment near the crest of stockpiles and wastedumps is a potentially hazardous practice which often results in localized slope failures. A limit plasticity approach to determine the total admissible weight for moving loads near slope crests is presented. A three-dimensional analysis provides an upper bound solution to the load that can be applied to the top of the slope (dump point), and it also provides the critical distances of the load from the slope crests. The analysis accounts for the inertial forces generated by the deceleration of a moving load (e.g., a dump truck), and it also includes the drag resistance of the front wheels if the brakes are engaged. The results can be utilized to determine the safe operating distances for mobile equipment from the slope edge. This presentation will discuss the application of limit plasticity to the development of the local three-dimensional collapse mechanism. An example with realistic parameters also will be presented.

Jan 1, 1991

By D. Bahrami, G. Danko

Spatial and temporal temperature and humidity variations for 5000 years are simulated in an emplacement airway within the conceptual, high-level nuclear waste repository proposed to be built at Yucca Mountain, Nevada. A multi-scale model is configured using MULTIFLUX, a thermohydrologic-ventilation code. The predicted surface temperature of most waste packages during post-closure exceed 140oC, the threshold limit known for likely localized corrosion for Alloy 22 waste package material. Small amounts of infiltration airflow through the mountain in Panel 5 are found to transport liquid water condensate to some of the waste packages emplaced along the peripheral section of the drift due to edge cooling.

Jan 1, 2004

By K. Verghese, H. M. Lee, R. P. Gardner, K. Boateng

Results of work on the development of a phenomenological model for the continuous flotation process wing short-lived radioactive tracer techniques for determining model parameters is reported. A model that incorporates a flotation first-order rate constant and a residence time distribution based on the cross-flow finite-stage (CFFS) model has been derived and investigated. The short-lived radioactive tracer techniques and the nonlinear search methods necessary to extract the model parameters have been developed. The conditions under which all the model parameters can be extracted from a single radiotracer experiment are detailed and illustrated. A micro- computer-based unique data logging system has been designed, assembled, and implemented for collecting the necessary transient radiotracer data. Results are reported for a continuous laboratory flotation process for the two systems, mica ore and coal.

Jan 1, 1987

By Martín A. Encinas-Romero, GUILLERMO TIBURCIO-MUNIVE, María M. Salazar-Campoy, Patricia Guerrero-Germán, José R. Parga-Torres, Luis S. Quiróz-Castillo, JESÚS L. VALENZUELA-GARCÍA

Pressure oxidation is a hydrometallurgical oxidative pretreatment for refractory ores, such as sulfide ores. Here, simultaneous alkaline pressure oxidation and sodium cyanide leaching treatments were carried out on a pyritic ore from the Mulatos Mine located in Sahuaripa, Sonora, Mexico. Mineral characterization, agitation leaching, hot cyanidation under atmospheric pressure conditions, simultaneous moderated pressure oxidation and leaching, and kinetic testing results are shown. The modified variables were temperature, pressure, and cyanide concentration. Characterization indicated that pyrite was the main mineral. Simultaneous pressure oxidation and leaching experiments were conducted at a temperature range of 40–80 °C, oxygen pressure of 87.5–200 psi, and cyanide concentration of 0.8–1.2 wt% in a 2-L Parr pressure reactor. A dissolution rate of 81–86% was achieved under the following conditions: 87.5 psi, 80 °C, 0.8 wt% NaCN, for 1 h.

May 7, 2020

By Richard P. Killmeyer, Carl P. Maronde, W. W. Wen, Peter J. Suardini

Under a cost-shared Department of Energy contract, awarded as part of the Coal Preparation Program&apos;s High Efficiency Preparation subprogram, Custom Coals International will be installing and testing a 227 kglhr micronized-magnetite cycloning circuit in PETC&apos;s Coal Preparation Process Research Facility. The project includes the design, construction, testing, and decommissioning of a fully integrated circuit complete with feed coal classification to remove the minus-30-micron material, dense-medium cycloning of the 300 by 30 micron feed coal using micronized magnetite (<10 microns), and medium recovery via drain & rinse screening and various stages and types of magnetic separation. This paper will describe the micronized-magnetite beneficiation technology and the scope of work for this project including an update on the status of the project, the circuit, and the proposed test plan.

Jan 1, 1995

By G. Stephan Derrickson

Any type of agitation within a confined vessel is primarily concerned with two parameters: 1) A level of agitation describing the homogeneity of the constituents (whether it be suspension or mixing) and, 2) the energy efficiency with which this level of agitation is accomplished. The following is an attempt to present a solution to the problem of adequately defining and optimizing these properties. First included is a discussion of the application of good design practices to the determination of a mechanically efficient shape to the blade elements of the propeller. These practices, excluding several appropriate modifications, have been known, but not well understood, in aircraft fluid mechanics for a number of years. Secondly, having optimized the direct impartation of energy to the medium being agitated, attention is turned to one of the more perplexing phenomena of multi-phase systems - definition and prediction of agitation levels. The result of recent study and testing is a method of scaling which the authors feel provides a lucid understanding of governing physical parameters within the agitator itself, allowing one to scale up and down with confidence.

Jan 1, 1982

By S. N. Groudev

A process for the combined chemico-biological removal of iron present as oxide minerals in different mineral raw materials (quartz sands, kaolins, clays, etc.) was developed. In the process, mineral raw materials are leached at about 90 °C with lixiviant containing microbially produced oxalic and hydrochloric acids. The leaching is carried out in mechanically stirred acid-resistant reactors for periods of from 1 to 6 hours, depending on the iron content and the forms of iron in the raw materials being leached. The iron contents of some sands treated by this method were lowered from levels that were in the range of 0.035% to 0.088% Fe2O3 to less than 0.012% Fe2O3, making them suitable for the preparation of high-quality glass. The iron contents of different kaolins were lowered from levels that were in the range of 0.65% to 1.49% Fe2O3 to levels in the range of 0.44% to 0.75% Fe2O3. As a result, the whiteness was increased from values of 55% to 87% to values of 86% to 92%. The iron content of clay was lowered from 6.25% Fe2O3 to 1.85% Fe2O3, and this increased the “fireproofness" of the clay from 1,670°C to 1,750°C. A similar process was used for the leaching of aluminum from aluminosilicates, mainly clays and kaolins. However, in this case, the microbial fermentation fluid containing citric acid was acidified by means of sulfuric or hydrochloric acid or by means of different mixtures of mineral acids. For enhancing aluminum solubilization, the aluminosilicates were heated before leaching at 600° to 650°C for 1 to 2 hours. Over 90% of the aluminum present in different clays and kaolins were leached within 3 to 6 hours. "Silicate " bacteria related to the species Bacillus circulans were used to leach silicon from low-grade bauxite ores containing aluminosilicates as impurities. The bacterial action was connected with the degradation of the mineral structures (by means of microbial metabolites such as organic acids and exopolysaccharides), as well as with the selective separation of the rich-in-aluminum fine fractions, which were retained by the mucilaginous capsules of the bacteria. The solid residues after treatment were characterized by higher values of alumina and silicon module (A1203: SiO2 ratio), and they were suitable for processing by means of the Bayer process for recovering aluminum. The bending strength and other ceramic properties of kaolins were improved by contact with well-developed cultures of "silicate" bacteria. The improvement was caused mainly by bacterial metabolites (exopolysaccharides) that acted as resins during drying.

Jan 1, 2000

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat absorption capacity of individual particles, which differs for different species of mineral. When a mixture of fine material is exposed to a radiant energy source, the various solids components present in the mixture will absorb heat energy depending on their composition and there will be difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal and quartz of 6 x18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating and system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Mar 2, 2022

By Sadatoshi Ohmori, Karen Shinoda, Nobuharu Isago

Method of tunnel excavation is generally classified such as full-face excavation, bench-cut excavation, diaphragm with center pillar excavation, center drift advancing excavation and so on. These excavation methods should be selected properly in terms of ground condition, the area of tunnel section, the arrangement of construction. Center drift advancing excavation method in mountain tunnel construction, is often applied under quite weak ground condition, prior to the main tunnel widening excavation. Recently, the advancing drift is for the excavation of extreme larger section in main tunnel to confirm the stability of face. In addition, we make advancing deformation occur in drift when the construction was done in poor ground like squeezing and swelling ground, and the force occurred in main tunnel was expected to reduce by the effect of ‘dodging’ for support structure. Mechanical relation between drift and main tunnel has been mainly grasped on past experiences in Japan. However, the characteristic of tunnel enlargement was partially discussed by using the three dimensional analysis and the result was grasped by past experiences on the basis of each tunnel construction. It is considered that the natural ground stress is normally released as the advance displacement, but it was released after the main tunnel widening, causing a displacement and deformation increase. Up to now, the construction practice has shown the reduced displacement during the main tunnel widening excavation by the drift, and the numerical analysis agreed with above observation. However, there is no report found that the displacement and deformation at the time of widening excavation of the main tunnel become larger in case of a drift application. In Kyusyu area, western part of Japan, the northern part of Yoshinomoto tunnel was applied an advancing bench-cutting method for a center drift for the purpose of obtaining the geological information for support selection of the main tunnel in widening excavation. The shape of center drift was a perfect circle with a diameter of 4.0 m or 6.0 m and the same temporary support regardless of the geological situation. As a result, the displacement and deformation of the main tunnel after widening excavation were larger than the section where the center drift was not applied. Furthermore, the displacement and deformation of the main tunnel after its widening excavation was considered larger in the section where the cross-section of the center drift with 4.0 m diameter was applied than one with 6.0 m. Therefore, the center drift with a high rigidity support structure had the effect of suppressing the advancing deformation prior to the main tunnel widening excavation.

Jun 13, 2021

By Scott G. Britton

This chapter discusses the necessary construction techniques for installing coal mine ventilation devices. Included in the discussion are the major air controlling devices called over- casts, regulators, stoppings, and doors. Under-casts, although a valid device, are used infrequently in coal mining and are not discussed here. Typically, coal mines require a great many ventilation devices to control the air movement. Post-I969 mines have had to design their air systems to comply with the Federal Coal Mine Health and Safety Act (CMHSA) as discussed in Chap. 1. Pre- 1969 mines have had to redesign major portions of their systems to comply with the basic components of the law such as separation of air courses, single unit split ventilation, and minimum air quantities. It is not uncommon, therefore, to find a large mine (2.0 Mt/a) requiring several hundred overcast installations (permanent, as well as repeat construction), plus doors and regulators placed among a thousand or more stoppings. When each of these devices is subject to leakage from installation and weathering defects, the importance of effective construction becomes evident. An historic rule of thumb for average mine ventilation says that about 70% of all the air pressure generated by the mine fan is lost between the portal and the working faces. Of course, this rule is subject to many factors, but the message is clear: there is a tremendous inefficiency in controlling leakage through common air devices. This chapter strives to present a standard approach and design alternatives which can go a long way in reducing this leakage, and hence, ventilation costs. Historically, mine ventilation has progressed from natural, or draft ventilation, to fire-induced ventilation (Fig. l), furnace-fired centrifugal fans and finally, to today&apos;s modem mine fans. Underground controlling devices have been in use in the coal mines since the late 1600s, but the CMHSA of 1969 was the real turning point for mine ventilation. Minimum quantities and velocities of fresh air were required for mining, forcing coal operators and engineers to reevaluate and improve their systems. As a consequence, the cost for ventilating air increased. Today, companies face a variety of choices among design alternatives, materials, labor, and costs of ventilating devices for their mines. The best approach for any individual company or mine is determined by (1) the needs of the mine, and (2) the local design parameters. In my discussions of ventilation construction I shall be fairly general in terms of device installation steps, where specifics are warranted for clarification, I will include this information.

Jan 1, 1983

By P. Schilizzi

The increased impact of mining subsidence in the U.S. coalfields and the recent regulatory constraints legislated by government and state agencies have provoked an intense research effort on this topic by government agencies, coal companies and academic institutions. Subsidence and horizontal strain predictions are a basic requirement if subsidence and its associated effects are to be controlled and contained within acceptable environmental levels. As a result, several such prediction techniques have been proposed or are currently under development to assist coal operators in minimizing the detrimental effects of these surface deformations. VPI&SU has been actively involved in this research effort in the past few years, with particular emphasis on the Appalachian coalfield. During the initial stages of this research a large number of subsidence case studies were collected from the literature, the coal industry and government agencies. In total, data from 32 longwall panels and 60 room and pillar panels were collected. This data bank was used to determine relationships between the basic mining and subsidence parameters, in order to allow the evaluation of the various prediction methods for the Appalachian coal region. Based on this data two subsidence prediction techniques, one based on profile functions and the other on influence functions have been developed. Profile function methods provide a tool for a fast calculation of subsidence on a line across a mine panel. Influence function methods, on the other hand, allow for a more detailed calculation of ground movements, in any mode and at any depth, on a grid or at any specific point. The limitations of the data of the collected case studies, i.e. accuracy of surveys, frequency of monitoring, lack of horizontal movement measurements, etc, led VPI&SU to the initiation of a detailed subsidence and strain monitoring program above a number of active mines, located in three major coal producing counties of Virginia. The aim of this program was to enhance the data base with accurate and complete measurements of surface movements and to allow, therefore, the refinement of the prediction techniques. This paper presents this monitoring program, discusses in detail the results obtained from three specific case studies and provides recommendations for the implementation of the field data in the general prediction methods.

Jan 1, 1986