Search Documents

By Glenn Boyce, Paul Gribbon, Gary Irwin, Greg Colzani, Jim McDonald

This paper discusses the process utilized by the City of Portland Oregon’s Bureau of Environmental Services (BES) to procure and compensate Impregilo-SA Healy (I/H)for the West Side Willamette River Combined Sewer Over?ow (CSO) Project. The contract method is a three-phase process consisting of qualifications based contractor procurement, pre-construction phase design assistance/construction planning, and facility construction where the contractor is compensated on a cost reimbursable-fixed fee basis. The paper focuses on pre-construction phase lessons learned from the development of the contract general conditions, establishment of a construction budget and cost control program, incorporation of contractor recommended design changes, and development of a subcontractor procurement program for construction.

Jan 1, 2003

By R. L. Lewis

The White Pine Mine is the second largest active underground copper mine in the United States, covering an area of approximately 34 km2 in the Upper Peninsula of Michigan. A numerical flow model of the White Pine Mine was constructed to evaluate engineering controls that would reduce the rate of mine water discharge after closure. Of the passive controls evaluated, the placement of low-flow bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35 percent.

Jan 1, 1996

By O. M. Bishop

Large reserves of copper are contained in waste dumps which have been created by open-pit mining of porphyry-type copper deposits in the Western United States. Nearly 6 billion tons of copper-bearing material exists in the waste dumps at present, and another billion tons will be added each three to four years as additional material is stripped from the present mines and new open-pit mines are developed. The dumps constitute an enormous resource containing some 7 to 10 billion dollars worth of copper. Increased attention is being given to the recovery of copper by leaching from these dumps as attested by the fact that in 1968 approximately $175 million of copper was recovered by leaching operations. During the leaching process, however, numerous problems exist which prevent complete extraction of the copper from the dumps. Probably the most important problem encountered is the incomplete contact of the copper-bearing materials by the leaching solutions. This problem is mainly created by the formation of physically compacted and chemically cemented layers within the dumps which prevent solution flow to many sections of the interior of the dumps.

Jan 1, 1970

A Directory of Computer Programs Applicable to US Mining Practices and Problems. A. L. Sanford, T. L. Myers, and J. F. Stiehr. USBM OFR 131-78, Nov. 1977. A Master Environmental Control and Mine System Design Simulator for Underground Coal Mining. Tape MDS-5. Pennsylvania State University. USBM CT 1.77, Dec. 1975. Contains computer programs on a dynamic general purpose computer simulation model for underground coal mining. A Method for Computing Stabilization Pressures for Excavations in Incompetent Rock. J. D. Dixon and M. A. Mahtab. USBM RI 8128, 1976. Describes technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. Accident Cost Indicator Model to Estimate Costs to Industry and Society From Work-Related Injuries and Deaths in Underground Coal Mining. Vol. I.III. D. G. DiCanio, A. H. Nakata, D. Colvert, and E. G. LaVeque. OFR 39(1)(3)-77, Dec. 1976. Describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents In underground coal mines. An Interactive Computer System for Evaluating Coal Mine Illumination. R. Goldstein. USBM OFR 110-80, March 1980. Computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights. Analytical Modeling of Mine Roof Behavior Using Statistical Material Properties. R. T. Langland and F. J. Tokarz. USBM UCRL-51876, Aug. 1975. Analytical study of coal mine roof behavior using a computer model of a room-and-pillar mining method. Application of a Total System Surface Mine Simulator to Coal Stripping. Vol. I-VII. Pennsylvania State University. USBM OFR 33(1)(7)-78, Aug. 1978. Describes model development, input and output documentation, three case studies of an open-pit materials handling simulator, and development of two equipment selection models and a cost model. Characterization of the Structural Behavior of Rock Masses. Vol. I-II. L. R. Herrmann and M. A. Taylor. USBM OFR 67(1X2)-75, Sept. 1974. Computer subroutines for characterization of rock behavior, Including variability of properties within the rock mass, planes of weakness orthotropy, strength criteria, and post-failure behavior. Coal Mine Electrical System Evaluation. Vol. I-VII, L. A. Morley, et al. USBM OFF! 61(1)(7)-78, 1977. A concept to improve underground coal mine electrical system safety and availability. This proposed technique is based upon the ability to predict incipient failures in the mine power system. Prediction is made possible by a new method which uses a minicomputer to implement pattern recognition algorithms. Computer Modeling of Fluid Flow During Production and Environmental Restoration Phases of In Situ Uranium Leaching. R. D. Schmidt. USBM RI 8479, 1980. Describes development and application of a computer model for simulating the hydrological activity associated with in situ leaching. Interpretation of Rock Mechanics Data, Vol. II (A Guide to Using UTAH2). W. G. Pariseau. USBM OFR 47(2)-80, June 1978. Brief description of a two-dimensional elastic-plastic finite element program intended for mine stability analysis. Iterative Approximation Techniques for Microseismic Source Location. G. H. Dechman and Meng-Cherng Sun. USBM RI 8254, 1977. Iterative approximation method for microseismic source location developed to adapt microseismic techniques for rock structure analysis to investigations of surface problems such as slope failure in an open-pit mine. Limits and Cost Sensitivity of Alternative Parting Handling Methods. Vol. I-II. T. E. Finch, D. R. Haley, and C. J. Speaks, Jr. USBM OFF! 117(1)(2)-77, March 1977. Programs to examine alternative methods of handling the parting between two coal seams in a surface mining operation. Alternative methods consist of equipment implementation in either a stowing or haulback technique. Methane-Water Flow in Coalbeds. H. S. Price. USBM CT 1-79, April 1972. This computer program calculates transient, two-dimensional, gas¬water flow in a porous medium. Plastic Canopy-A Computer Program for the Structural Analysis of Protective Canopies. K. D. Winters, G. A. Gavan, and J. C. Ault. USBM IC 8795, 1979. Presents a FORTRAN IV program for the structural analysis of protective canopies used In underground mines and rollover protective structures used in surface mines. The Three-Dimensional Structural Analysis of Double-Entry and Single-Entry Coal Mines. Vol. I-III. Agbabia Associates. USBM OFF 16(1)(3)-80, Oct. 1978. Describes the computer program designed to perform a three-dimensional finite element analysis of an instrumented section of double- and single-entry coal mines. Underground Mine Evacuation Plans Analyzed by Computers. D. Tesarik, D. Nicholson, and A. B. Boghani. MSHA, Vol. 4, No. 5, Oct. 1979. USBM has developed a computer program to evaluate and construct mine evacuation procedures and plans.

Jan 11, 1981

By A. Bruynesteyn

Procedures are discussed to determine if a waste material can become acid producing when left exposed to the environment. When wastes proves to be acid producing, methods are described that can be used to determine the characteristics of the effluents produced from a commercial size waste dump, taking into consideration that large quantities of pollutants can accumulate inside a waste dump during dry periods. The length of such dry periods and the quantity of rainfall greatly affect effluent characteristics.

Jan 1, 1980

By Harry Perry

The Bureau of Mines is glad to have this opportunity to discuss its present Coal Research Program and its significance to the industry with a group which has for many years been representative of the coal producing community. We believe we have a dynamic program that will help our vast coal resources to find their proper place in the U. S, economy. The present coal research activities of the Bureau are conducted in three organizational subdivisions: Minerals Research, Mineral Resource Development, and Health and Safety. All investigations are carried out in Bureau research facilities located in different sections of the country, Since its creation by the Organic Act of 1910 and subsequent amendments, the Bureau has worked closely with the coal industry--first by providing assistance in mine safety for anthracite and bituminous coal mining, and since that time, in providing information on conservation, safety, mining, preparation, and utilization.

Jan 1, 1966

By Michel Dagbert

The determination of the precision of reserve estimates (tonnage, grade, quantity of metal) for an entire deposit or a large block in a deposit has received some attention in the early developments of geostatistics. A general formula to derive the estimation variance of any linear combination of a large number of sample values can be found in any geostatistical textbook like David (1977) or Journel and Huijbregts (1978). A particular case of this general formula is of course the kriging of the entire deposit. However, besides the technical difficulty of dealing with many samples the application of this formula necessitates the knowledge of the covariance between any two samples in the deposit. This is quite unrealistic in the usual case of limited stationarity where the assumption of a covariance or a variogram just function of the distance vector between two samples is only valid for samples within the same area of restricted size.

Jan 1, 1982

By William P. Walsh

In December 1983 the author undertook an investigation in east Texas which was organized to learn the feasibility of applying geophysical techniques over shallow lignite deposits. The work embraced experimental high resolution seismic reflection and offset Wenner resisitivity sounds over three 4 to 4 mile test sections. This site also was sponsored by Woodward-Clyde Consultants (WCC) and a consortium headed by North American Coal Corporation. The principal objective of this investigation was to learn whether the aforementioned geophysical techniques could be applied over shallow lignite deposits (i.e. located at approximately 100' to 300' in depth) and consequently provide structural and stratigraphic information useful for resource and reserve characterization. A secondary objective was to determine if these same techniques could disclose the nature of the overburden and the distribution of ground water therein.

Jan 1, 1985

By S. B. Hildebrand

One of the highest costs associated with insitu leaching of copper is electric power. The ReGeneration Project addressed this cost issue with a research and development project for BHP Copper. The project involved the installation of a reverse pump/turbine for the removal of excessive fluid pressure and the production of useful electric power. The motivation for the project was that a reverse pump/turbine unit could not only remove the excess hydraulic pressure, but when connected to an induction .generator, would produce electric power, which could be easily connected to the local power gird, thus reducing operating costs. The project was successful in removing excess fluid pressure and producing electricity. The unit is operating today, producing useful 2,300 volt power at a rate of approximately 128 kilowatts.

Jan 1, 1998

By Richard C. Corson

Modern microprocessor systems make it possible to use several variables to anticipate changes in the process and to react with responses before upsets can be magnified by the process or by control action. Through tighter control, "insurance" can be eliminated from process set points without affecting product quality. In actual operation with a traveling grate furnace this control philosophy has produced savings of up to 20% in fuel consumption and 8% in fan power usage while producing a more consistent quality product.

Jan 1, 1982

By Martin Valeri

The operation described in-this paper will be confined to the Nemacolin Mine of The Buckeye Coal company, Nemacolin, Pennsylvania.' This mine is-located on the Monongahela River approximately sixty miles south of Pittsburgh. The mining is in the Pittsburgh seam that has an average thickness of 88 to 90 inches. The current practice is to mine approximately 80 inches, leaving 8 to 10 inches of roof coal. All of the coal produced is used solely for by-product coking by the parent Youngstown Sheet & Tube Company, Youngstown, Ohio. Eight to ten inches of top coal are left by the miners to prevent air slacking of the draw slate. In addition, this top coal which will float at the washing gravity has a very high ash and sulphur content, and when mined, seriously affects the quality of the clean coal product.

Jan 1, 1961

By M. Javier

"Mining is the main activity that supports civilization. Actual mining presents contradictory concept to the health of the planet. Its business model is linear, fragmented and characterized by inefficiencies in the utilization of water, energy and mineral resources which generate waste and pollution. Before mining begins, it is critical to determine the vulnerability of the ecosystem and after mining, it is critical to determine the depletion of nature. Attending to these vital matters will require quantifying and measuring them. The purpose of this study is to provide and establish the metric to assess the performance and manage a sustainable future for our existence and that of our planet. This index is defined to measure and control Nature Friendly Sustainability (NFS) based on understanding nature. This index will determine the condition of nature constructed on the measurement of physical, chemical and biological equilibrium. Proposing a new mindset for mining design to satisfy nature’s needs would be to offer the same opportunities to future generations. Hence, sustainability is synonymous with equilibrium under a limited ecosystem. Nature is interconnected. Finally, this index of NFS is readable, standardized and relevant to keep nature’s needs in equilibrium. Establishing and NFS index is the next metric for humanity. INTRODUCTION There are a multitude of definitions of what sustainability is. Most of them are defined in terms of the corporate entity from which they emanate. The classical definition of management states that, “if we do not measure it, we cannot manage it.” Management of ecosystems is the definition of sustainability. Indicators of quantity and quality of sustainability are vital in order to create a metric for sustainability. These indicators will measure the depletion and degradation of nature as they occur through human intervention. The first step is to create a metric of sustainability to simplify its definition. The definition of sustainability is based on whether or not you consider nature to be finite or infinite, which is described in Nature Friendly Sustainability (NFS) [1]. The definition of NFS applies to any anthropogenic activity with an understanding of the equivalent activity in nature. That is to say, human activity with nature requires balance and equilibrium in order to be sustainable. The importance of this equilibrium is quantified in a set of metrics in order to establish measurement and acknowledge indicators for our dependence on nature. Sustainability is synonymous with equilibrium in any ecosystem that is limited and fragile. In the graph is the explanation of sustainability definition. See Graph 1"

Jan 1, 2017

By Donald Towse

Portland cement is a basic building material in every country in the world, and, fortunately, the raw materials required in its manufacture are widely distributed. It is a low-priced bulk commodity (price one cent a pound or less, with a density of 100 pounds per cubic foot.) Table 1. Approximate price per pound of selected mineral products. Copper 48 cents per pound Aluminum 27 Lead and zinc 15 Asbestos 3 to 18 Pumice 6 Sulfur 2 Bauxite (abrasive) 1.8 Barite 1 to 1.6 Cement 1 Primitive regions may get along without any Portland cement, but most countries use some, and it is one of the most widespread building materials, even if used in small quantities. Use of cement begins early in a country's development, and, because of local availability of raw materials, cement manufacture is one of the first heavy industries many countries desire. Use and manufacture of cement usually precedes other industrial materials such as steel and heavy chemicals, and consumption levels off for a long period during development of infrastructure and an economic base. With a mature economy comes a very high consumption. Per capita consumption varies ten times or more between nations (Figure 1).

Jan 1, 1970

By Francesco Chiappalone, Daniele Nebbia, Lance Waddell, Greg Colzani

As part of the 3RPORT Project, a 5-mile tunnel is being excavated underneath the three rivers of Fort Wayne using a 19-foot diameter Slurry Tunnel Boring Machine. The groundwater pressure at the tunnel axis ranges from 4.5 to 5.3 bar. The rock mass hydraulic conductivity is very high with water inflows up to 10,000gpm imposing significant challenges to the project. After excavating 1,550-feet of the TBM tunnel, major leaks between the tailskin and the segmental lining were observed, indicating the potential deterioration of the tailskin brushes and the need for inspection and eventual replacement. The first part of the paper describes the planning of the intervention, including the design of the polyurethane grouting campaign, the procedures developed for the execution and the controls established during construction to timely assess the presence of potential hazards. The second part of the paper focuses on the experience gained during execution and lesson learned to prevent future occurrences of this nature.

Jun 13, 2021

By Frank P. Traczyk

INTRODUCTION The process of solid-liquid separation can be an important decision in plant design. It is very important that one must consider not only the most effective means of solids-liquid separation, but also to consider the effects on upstream and downstream processes. A solid-liquid separation is done either to remove the solids £ran the liquids as in copper concentrates or rave a liquid from the solids as in uranium operations. In either case, washing can be an important consideration to clean the solids or recover the liquids. This section will deal with solid- liquid separation other than thermal, sedimntation processes, or hydro cyclones. The three major areas discussed are pressure filters, vacuum filters, and centrifuges that are most cannon in the minerals industry. PRESSURE FILTERS Pressure filters are one common type of solid-liquid dewatering devices. There are my different types of pressure filters that are both continuous and batch operations. They are characterized by using an external pressure to push or force the slurry through porous media to force the liquids out of the solids. Whereas vacuum filters are limited to one amsphere or bar working pressure, some types of pressure filters operate as high as 16 bars pressure. Pressure filters are also effective for hot slurries where a high boiling point can be a problem or precipitation occurs under vacuum. The types of pressure filters most common in the mineral processing industry include plate and frame and recessed plate filters. Some of the new technologies including automatic pres- sure filters and belt presses are also discussed. Plate Frame Filters Plate and frame filters are one of the oldest and most effective means of both dewatering solids and clarifying liquids. Plate and frame filters consist of a skeleton that is used to hang or support alternate plates and frames that are pressed together to form chambers. The filter plates consist of a drainage grid that is covered by sane type of filter media through which a liquid is

Jan 1, 1986

By Ki Chun

Optimizing ore processing requires a thorough understanding of not only the process itself but the economic constraints which influence business decisions. No single modeling technique is able to model all the different processes running in today's mines. The solution then is to use a number of different model­ing techniques, each competing with the others to best correlate the data. Among these modeling techniques are: Neural Networks, Genetic Algorithms, Fuzzy Logic, Crisp Logic, Statistics, First Principal Models, and System Identification models. Once a model has captured the behavior of the process, a numerical optimization determines the optimal operating point and set point parameters. A single step is then taken in the direc­tion of the optimal location by changing all the process parame­ters to the setting recommended by the optimization system. As the process begins to re-stabilize, the models are updated, the new optimal determined and another step is taken in the direction of the optimum. Through the use of multiple competing models integrated into a numerical optimization the process can achieve the optimal running condition even if the ambient conditions fluctuate dynamically.

Jan 1, 1998

In late 1993, Inco Ltd. completed a $600-million environmental improvement project at its Sudbury, Ontario operations -the largest single environmental project ever undertaken by a Canadian corporation. Efficient new facilities and innovative technologies installed during the course of the project have also significantly improved Inco's productivity and competitiveness. In early May 1994, a panel of 18 Inco authors contributed to a Technical Forum, "Environmental Programs at Sudbury," presented at the 96th Annual General Meeting of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) in Toronto. Their papers have been published in CIM's Toronto `94 Proceedings Volume, pp. 62-77. The following report draws primarily on discussions of Inco's milling and smelting operations published in the Proceedings Volume. The Proceedings Volume also includes papers on the acid and oxygen plants and on engineering, construction and commissioning of the project. The 222-page Proceedings Volume is available from CIM, $C27 plus shipping. To order, contact: V. Ward, CIM, Xerox Tower, 1210-3400 de Maisonneuve Blvd W, Montreal, Quebec, Canada H3Z 3B8; phone 514-939-2710, fax 514-939-2714. Lane White, Publisher.

Jan 1, 1994

By Roger A. Kauffman, Dean Van Dyk

Feldspar is the earth's most abundant mineral group. The feldspars are aluminum silicate minerals belonging to the tectosilicate class. Feldspars are the most widespread of any mineral group and are estimated to constitute 60% of the earth's crust. They make up a large percentage of the exposed rocks as well as soils, clays, and other unconsolidated sediments. Feldspars are widely used in the glass and ceramic industry and are principal components in rock classification schemes. Feldspar minerals and their production are important contributors to the domestic and world economies and standard of living. In 1990, the United States produced 630 kt of feldspar minerals, and world production was estimated to be more than 5 Mt. Feldspar mineral production in the United States has a long and interesting history (Feitler, 1967, Rogers Jr. et al., 1983). The first commercial production in the United States occurred in about 1825 and came from pegmatite bodies located in Connecticut, where feldspar was mined, hand sorted, and shipped to England. Feldspar production grew during the 19th and 20th centuries with important developments in production location, integrated mine and processing facilities, and the development of the flotation process for feldspar by the US Bureau of Mines and the feldspar industry. The first commercial feldspar flotation plant began operations-in Kona, NC, in 1946, some six years after this process had been developed. In 1990, the domestic feldspar industry consisted of 12 operating companies with mines and processing plants located throughout the United States (see Table 1). During the last 25 years, the domestic feldspar industry has been dynamic, marked by new plant construction and capacity expansion at older plants. The industry has also seen plant closures, changes in ownership of existing operations, the consolidation of the Canadian nepheline syenite industry, and the increase of imported feldspar products. The industry has been affected by contractions in its major end-use markets brought about by economic cycles, product substitution, and environmental effects, such as recycling, land-use controversy, and air and water pollution. Despite problems, the industry remains mature and highly competitive. GEOLOGY Mineralogy The common feldspar group of minerals form a single crystalline phase or solid solution series of minerals. Fig. 1 is a ternary phase diagram that shows the feldspar mineralogy-KAlSi,O8, NaAlSi3O8, and CaAl2Si2O8. The end-member compositions are also referred to as potassium, sodium, and calcium feldspar. The feldspars whose chemistry ranges between the potassium and sodium end-members are known as alkali feldspars, while those between the sodium and calcium end-members are plagioclase feldspars. These feldspar groups can be further subdivided based on structural and compositional features within the alkali or plagioclase feldspar series. The distinction between and the proportion of members of the two feldspar groups are important to the classification of igneous rocks (Deer et al., 1966). Perthites are the exsolution product of an initially homogeneous potassium-sodium feldspar solid solution which forms (in an environment of decreasing temperature) a heterogeneous intergrowth of sodium-rich feldspar lamellae in a host crystal of potassium feldspar. Antiperthites are exsolution products in which the host mineral is sodium-rich plagioclase feldspar and the intergrowths are potassium-rich feldspar.

Jan 1, 1994

By Randhir Sehgal

Heavy media processes have been used for cleaning +28 mesh coals for a number of years, Two applications, i.e., the vessels and the cyclones are widely used in the U. S. for this purpose. The basic reason for the popularity of these systems is their extremely high efficiencies for particle sizes above 28 mesh, However, application of heavy media technology to fine coals below 28 mesh, has been limited due to the following reasons: o Inability to make size separations effectively at sizes below 28 mesh o Necessity of feeding large quantitites of magnetite to the separators o Difficulty of recovering magnetite in the presence of large quantities of coal o High levels of coal contamination in the recovered media, leading to high circulating loads and ineffective control of media gravity

Jan 1, 1981

By P. Bevilacqua, M. C. Williams, T. P. Meloy

We will bet you that, without prior programming within 10 minutes, we can design and simulate a 10,000 unit operation separation circuit. We will even do it at your place. We do it all the time. [ ] There are no tricks; we do it in a spreadsheet. We do it in those user friendly spreadsheet such as Quattro Pro. Spreadsheets must be user friendly. Accountants use them as do managers, business men, lawyers, doctors and salesmen. What these users seldom realize, is how powerful a mathematical tool a spreadsheet is. Among their other capabilities, spreadsheets can do a finite element analysis. That is why they are useful for accounting. That is also why they are more useful to engineers in the mineral industry. Spreadsheets are ideally suited for the engineering problems in the mineral industry. We have used then for solving problems in: a) mine ventilation; b) circuit design and optimization of dense media, flotation and sizing; c) comminution circuit design; d) shaking tables; e) Humphrey spirals; f) sluice ways and channel flow; g) lock particle and liberation problems; h) tunnel and shaft stress problems; i) cascadograph simulation; j) complex heat transfer problems; k) flow in porous media; and sheet flotation (Figure 1). Mineral industry problems presented on or with a spreadsheet are an excellent teaching instrument, problem statement and solution tools and sales devices. Spreadsheets answer easily, quickly and reliably many mineral industry engineering problems. What makes spreadsheets so useful to the mineral industry. The short answer is: they are easy to use; mineral industry problems fit the spreadsheet format. Those reasons are part of the answer. The real answer lies with the structure of the spreadsheet itself. Essentially, a spreadsheet is a "finite element analysis" form of computer software. Many mineral industry problems are readily solved by finite element analysis techniques. While some in the mineral industry may think they have never heard of finite element analysis, most use it weekly if not daily. Any profit and loss statement is essentially a finite element instrument. In fact, any array of numbers where one number is related to another may be construed as a finite element analysis product. Finite element analysis is a common daily activity. To get an appreciation of a finite element analysis, think of a monthly sales forecast for the next year. For each product and for each month, there exists a dollar figure for the forecasted amount of sales. In the forecast statement, for a given product in a given month, there is a "box" where the forecasted figure is presented. The forecast figure in that box was arrived at through some type of formula. The formula probably required some information from other neighboring boxes in the master forecast statement. Voila, one has a finite element analysis. Today the analysis would be done in a spreadsheet. A typical mineral industry problem is ventilation in an underground mine. Think of a rectangular room and pillar mining operation. Each room has air entering at a given pressure and velocity and air leaving at another pressure and velocity. During steady state, the air entering and leaving the room is determined by conditions in the adjacent rooms. One can readily model the room and pillar mine layout in a spreadsheet, and then find the flow in and out of each room at steady state. Change the flow by moving a brattice cloth or blocking off a path way and one gets a new air flow profile. Change the numbers on the spreadsheet that reflect

Jan 1, 1993