Search Documents

By Willie Hefer

Contents ?Purpose ?Introduction ?Deviation of bias results ?Operational correctness ?Maintenance and Costs ?Conclusion ?Acknowledgements

Jan 1, 2005

By H. P. Carlisle

The significance of the mineralogical and surface characteristics of gold grains in the recovery process by C. E. FEATHER and G. M. KOEN Published in the Journal. February 1973. DISCUSSION H. P. Carlisle. B.Sc. (Eng.) Rand (Fellow) The authors are to be congratulated on drawing attention to the importance of surface characteristics in the treatment of gold grains. I must, however, confess to considerable doubts about the validity of the distribution of gold in "free" and "locked" form set out in Tables I to IV.

By A. Vogelzang

The paper describes how the level of the water-table was reduced as a result of increased pumping of water from the mine. Because such a condition in an area where there is compactable material above solid dolomite results In surface movement, steps were taken to restore the water-table to its former level. These included the return of water underground via a sinkhole and boreholes, and the piping of water from another mine.

Jan 1, 1978

The possibility that type 430 stainless steel can become sensitized during annealing after hot-rolling was studied by simulated cycles of continuous-annealing heat treatments, and by calculation of the carbon solubility. It was found that the lower-carbon steel could be sensitized at lower annealing temperatures than the higher-carbon steel, which is in line with plant experience. The difference in sensitization behaviour is ascribed to the lower rate of recovery of the lower-carbon steel during cooling, since recovery is sensitive to the grain size. At practical heat-treatment temperatures, austenite formation does not play a role.

Jan 1, 1996

By P. R. Jamisch

The limitations of gold-mine evaluation by P. R. JANISCH, B.Sc. (Sur.) (Natal) (Visitor) Inherent uncertainty in the choice of parameter values places theoretical and practical limitations on the interpretation of a gold-mine valuation that are not necessarily removed by comparison of two valuations on the same assumptions. These limitations arise mainly in the estimates made of cost inflation and gold-price escalation, and lead to inconsistencies in the 'league table' method of investment analysis. The choice of discount rate is also critical in many cases. An approach to the overall problem that takes these limitations into account is suggested.

Jan 6, 1976

By J. E. Forbes

Oxygen enrichment of the converter air at Rustenburg Platinum Mines by J. E. FORBES (Associate Member)* An account is given of the adoption of oxygen enrichment to accelerate converting operations and so permit the handling of larger quantities of feed materials. In addition to achieving its object, the use of oxygen-enriched air (6 per cent oxygen by volume) results in an increase in the concentration of sulphur dioxide in the converter off-gas. The slags have the same composition as those produced without oxygen enrichment, and the operation of the converters is easily controlled.

Jan 1, 1977

By J. W. S. Koel, T. R. Twidle, P. C. Engelbrecht

The process flows of the three flotation circuits at the concentrator of the Black Mountain Mineral Development Company (Pty) Ltd are described. Because of the complexity of the circuits and the associated reagent regime, the plant is equipped with a comprehensive range of control equipment. The different process-control strategies are discussed, and the modifications that have been necessary to the stabilizing control loops in the copper, lead, and zinc flotation circuits are shown in detail. It is concluded that the control strategies have continued to bring about benefits and improvements to the process.

Jan 1, 1986

By Allan Jansen, Robin Bissett

[Power-Point Presentation]

Jan 1, 2005

By D. A. Fenton

The structural design of large grinding mills, with reference to shell-mounted bearings by D. A. FENTON*, P. Eng. (Visitor) The paper outlines the advantages of shell-mounted grinding mills over mills having a conventional trunnionsupported shell. The growing use of larger mills in the past decade has led to a significant number of mechanical and structural failures, the most common being those at the junction of the head and the shell. Larger mill diameters favour the use of shell-mounted bearings. The elimination of castings, which have an inherent weakness to fracture, makes the shell-supported mill lighter and stronger than a conventional mill of the same shell thickness.

Jan 9, 1976

By J. A. L. Napier

The application of excess shear stress as an aid to the design of mine layout is reviewed, and the critical parameters required to describe slip on a plane of weakness are noted. A design procedure that is required to model the cyclic build-up of excess shear stress is described. A number of simple examples of mine layouts on two reef planes intersecting a fault plane are then considered to illustrate the application of the design concept and to highlight some of the pitfals that may be encountered

Jan 1, 1987

By C. O. Beale

This paper is the first part of a two-part review on the subject. , , .. Here reference is made to the place of copper among the elements, Its properties, Its historical significance, and its 'end uses both in general and in South Africa. Its current market situation and its prospects are dealt with briefly. Some account is then given of the mining and metallurgical techniques employed. in South Africa in the production of copper, together with the names of the companies at present Involved and brief descriptions of their operations, ,... . .. The operations of these companies are described In greater detail In Part 11(Apn11985 Issue of the Journal).

Jan 1, 1985

It is shown that, when a flat-bottomed indentor is pressed into the surface of a strong rock, the normal force necessary to cause failure of the rock is reduced substantially if a shear force is applied to the indentor. A mathematical analysis is described, which shows that higher stresses are induced in an elastic material close to the free surface of the material ahead of a punch when a shear force together with a normal force is applied to the punch. Therefore, failure of the material would occur with lower forces applied to the punch. Stress trajectories show that fractures develop in the rock along lines of maximum principal stresses.

Jan 1, 1978

By H. J. S. Kriek

Methods are described by which increased production is achieved whilst retaining full availability of equipment and decreased refractory cost. Refractory materials have certain limitations, and when these limitations are known the variables in operating practice having the greatest impact on refractory life can be controlled. The most important factors to be closely controlled are porosity, chemical constitution of refractory materials, slag basicity, slag volume, FeO content of slag and temperature at which the process is operated. Knowledge of the process is invaluable in deciding on the type of refractory to be used. The types of refractories used in and the operating variables of the ironmaking, steel making and steel finishing units are described.

By R. R. Mankowski

The work described here attempts to underscore the importance of the time lag between the end of a loading phase and the instant a winding drum begins its acceleration phase. Traces generated from a computer-simulation model show that the amplitude of the stress oscillations occurring in mine hoisting cable during the constant velocity-of-ascent phase is a direct result of the temporal sequence employed between the loading and the raising phases. While current and early literature indicates that extensive work has been undertaken on the isolated effects of these two independent sequences, the literature does not appear to contain any documented evidence to suggest an optimal control or interfacing between these two dynamic regimes.

Jan 1, 1995

The 96th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room of the Transvaal Automobile Club in Johannesburg on Wednesday, 11th August, 1993. OBITUARIES The President announced the deaths of the following members of the Institute during the past year. Life Fellow E.F. Laschinger. Other Members R.K. Boright, J.S. Jacobi, R.D. Power, J.H. Cannon, C.J. du Plooy, L.B. Mcrae, C.P. Rossouw, A.L. Sillars, A.W. Heugh, R.K. Briggs, P.J. Stark, and C.S. Stott. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1993

By M. J. Nicol

The results are reported of experiments on the influence of a number of variables on the rate of loading of gold cyanide onto activated carbon and the equilibrium capacity of the carbon. These variables include the concentrations of gold and free cyanide in solution, the pH value and ionic strength of the solution, the concentration of organic compounds in the solution, the temperature, the particle size of the carbon, and the mixing efficiency. The experiments were carried out under approximately steady-state conditions to simulate the conditions in a countercurrent carbon-in-pulp absorption plant. In addition, the results are reported of experiments to establish whether the absorption of gold cyanide onto activated carbon is a reversible process.

Jan 1, 1983

By G. E. Blight

The load-compression characteristics of mine supports are usually evaluated by means of relatively rapid tests, whereas in the mine they are subjected to much slower strain-controlled compression. The effects of slow strain rates on the load-bearing properties of mine supports were explored by means of straincontrolled tests on model timber packs and timber-filled steel telescopic props. It is shown that the load-compression characteristics of these supports are considerably influenced by the rate at which they are compressed. The species of timber influences the behaviour, but to a relatively minor extent. Preloaded supports are shown to lose a significant proportion of their preload by relaxation.

Jan 1, 1978

By D. D. Marsden

This paper discusses the concentrations of sulphides and total sulphur in widely spread regions around mine residue deposits, from which rain-water run-of can enter the Vaal River system. Analyses of borehole samples from several deposits are used to establish typical sulphur head grades. It is shown that a high percentage of al the oxidizable, and hence leachable and pollution-causing, sulphur has already been removed. When the residues were fresh, water that came from the deposits was highly polluted, but the dissolved solids from these residues are today of very minor significance. The data are supported by analyses of the drainage streams.

Jan 1, 1986

By A. L. Painting

A study of the end effects in specimen cores under compression tests, with a view to the elimination of these effects by A. L. PAINTING (Student) It is well known that a cylindrical rock specimen tested under uniaxial compression in conventional fashion is subject to end effects; that is, towards the end of the core, the stress and strain distribution becomes non-uniform. The experiment described illustrates such end effects with an aluminium core between steel platens. An attempt was then made to nullifythese effects by compressing the core between pads of mercury. The resulting stress and strain distribution was significantly more uniform, but a slight over-correction was introduced.

Jan 4, 1974

Blasting in a gold mine has to satisfy the following set of techno economic conditions: good fragmentation, minimum stopped width, minimum number of rock falls, cost effectiveness. Results of a comparative study of the performance of a Low Density Anfo (LDA) and a conventional Anfo (ANFEX) are discussed. LDA appears to be more cost effective. The same borehole volume can be charged with material of reduced specific gravity. The velocity of detonation (VOD) is increased in the case of LDA resulting in more breakage as a result of shock energy than from the energy in the gas phase. This leads to less damage to the excavation and more favourable breakage of the excavated rock. As a result the overall economics of the mining operation is improved.

Jan 1, 1995