Search Documents

By B. Strohmeier

An account is given of the use of a computer to control the performance of three ultra-high-powered electric-arc furnaces in Iscor 5 steelmaking plant at Vanderbijlpark, South Africa. Several of the reports and graphs printed by the computer are reproduced.

Jan 1, 1985

By J. A. Drummond

The duties and efficiencies of a number of main and auxiliary fans were determined by standard and thermal methods. Some observations on the effect of water and dirt accumulation on fan performance were made.

By W. A. Hustrulid

CONTENTS PART I The theory of percussive rockdrill operation. Blow frequency Piston impact velocity and blow energy Thrust requirements Prediction of penetration rate Drillsteel life Bit wear PART II Measurements of percussive rockdrill performance Thrust-penetration rate measurements Blow frequency Piston impact velocity and blow energy Prediction of penetration rates The effects of hole diameter Thrusts applied by men Bit wear Appendix I Experimental procedure and rockdrill and drill steel specifications Appendix II Piston impact velocities and energies PART III Practical implications. Provisions of adequate thrust Conclusions INTRODUCTION In South African gold mines some 100 million tons of rock are broken each year by drilling and blasting. Only minor improvements to this method of rockbreaking have been made since the general introduction of pneumatic rockdrills for stoping 50 years ago and, more recently, of drillsteels tipped with tungsten carbide. The combined total cost of drilling and blasting amounts to almost R0,50 per ton of rock broken, which is just short of one quarter of the direct cost of stoping or development. Rockdrilling accounts for about R0,25 of the total cost of rockbreaking, of which RO,12 represents labour costs and R0,13 the cost of drillsteels, rockdrill spares and power. Mine air compressors use over 7 X 108 kWh of electric energy a year, amounting to 7 percent of the total electric power used by the gold mining industry. The efficiency of percussive rockdrilling is, therefore, of considerable significance to mining costs. Over the past four years the Mining Research Laboratory of the Chamber of Mines of S.A. has been engaged in experimental studies of percussive drilling. These experiments were conducted at test sites on Robinson Deep Gold Mine and Vlakfontein Gold Mine, made available by Gold Fields of South Africa, Limited. Three rockdrills, designated types A, Band C, of different manufacture, were used in the experiments which involved the measurement of the following operating characteristics: 1. Throttle air pressure 2. Applied thrust 3. Penetration rate 4. Air consumption 5. Blows per minute 6. Drill steel revolutions per minute. The results of these investigations are presented in three parts. Part I, "The theory of percussive rockdrill operation" which provides a concise, mathematical description of the performance of a percussive rockdrill in terms of its principal mechanical dimensions and operating conditions, and an analysis of the bit and gauge wear of drillsteels. Part II, "Measurements of percussive rockdrill performance" in which the experimental results are presented in terms of thrust-penetration rate curves at different throttle air pressures and throttle pressure-air consumption curves, which are shown to agree well with the predictions of theory. In addition, data relating gauge wear on the drillsteel and penetration rate to the distance drilled are discussed. Part III, "Practical implications" in which an analysis of the status of thrusting devices is made and the benefits that would derive from using uptimum thrusts are discussed.

By D. H. C. Griffiths, D. R. Davis, D. B. Paterson

Consolidated Murchison Limited is the only primary producer of antimony in South Africa, producing approximately 18 per cent of the total world production. This paper gives a technical review of the history, occurrence, mining, and metallurgy of antimony at Consolidated Murchison. World antimony markets are also discussed, together with the end-uses.

Jan 1, 1986

By H. L. Monro

CONTRIBUTION BY J. R. F. HANDLEY Mr Monro is to be congratulated on his concise treatment of a very complex subject. As a graduate with only Mathematics I in my curriculum, I am unable to comment on the mathematical treatment of the factors affecting his supply/demand model, but the logic does not escape me. The main conclusion is that any excess of supply to the spot gold market will depress the price in a normal market, and particularly in a falling market.

Jan 1, 1993

An investigation into the stability of large open stopes at Premier diamond mine, Culinan, South Africa, is described. The open stopes are located in a weak kimberlite orebody, directly underneath a 75 m-thick sill of gabbro. Two and three-dimensional stress analyses were carried out in a back-analysis of the stresses and failure around the first open stope created under the sill. The results were used in the prediction of the future stability of the planned open stopes, intervening pillars, and sill.

Jan 1, 1987

The increasing transportation of solids by pipeline, in South Africa and internationally, replacing the conventional transportation methods of rail, road, and conveyors, has resulted in much research into this area of solids transportation. Pipeline wear continues to be an area of specific concern, since it constitutes a major cost during the life of a pipeline installation. Wear data from an accelerated wear test and actual pipeline tests are presented. Trends in the performance of the pipeline materials tested are discussed, and possible solutions to the problem of pipeline wear are presented.

Jan 1, 1992

By J. H. Bulloch

A short review is given of the effects of corrosion fatigue on the materials used in pressurized water-reactor vessels. Selected topics such as testing procedures, test data, and mechanisms in simulated environments are discussed. The main fact that emerges is that most of the data on the growth of fatigue cracks reside below the ASME X1 1980 High-R 'Wet' design-code lines, Le. they fall within that specification. Finally, some recent advances in the understanding of the corrosion-fatigue behaviour of such materials in pressurized water reactors are highlighted.

Jan 1, 1987

By Johanna van Deventer, Sean Scott, Rene du Preez, Steven R. Izatt

In order to meet the stringent specifications associated with the production of LME Grade A cobalt cathode, producers need to ensure that a number of impurities, including Cd, are removed from the advance electrolyte to ppb levels (~0.1 mg/L). Conventional options include ion exchange using amino methyl phosphonic acid resin and solvent extraction using D2EHPA. More recently a Cd-selective resin, employing Molecular Recognition Technology (MRT), became available from IBC Technologies, Inc. These three potential unit operations were evaluated in parallel at Mintek. MRT was identified as the most technically feasible option. Results obtained on a cobalt advance electrolyte, containing 55 g/L Co, 6 mg/L Cd and 60 g/L Na2SO4, are presented in this paper.

Jan 1, 2007

By S. Budavari

On the one-hundredth anniversary of the founding of the South African School of Mines, this paper presents a historical review of the tertiary mining education carried out by the School of Mines in Kimberley and the subsequent institutions in Johannesburg. In addition to recording and evaluating a century of mining education, it describes the current activities of the Department of Mining Engineering at the University of the Witwatersrand, which is believed to be the natural successor to the School of Mines. The comparison of earlier and contemporary academic mining activities reflects a gradual transition from the educational philosophy and objectives of a school of mines to those of a modem university department. In the conclusions, some aspects of the educational effort expended during the past hundred years are briefly highlighted.

Jan 1, 1996

Two column flotation cells have been installed as single-stage rougher cleaners at Batu Hijau. The objective was to provide additional residence time in the cleaner circuit to maintain maximum recovery during high mill throughput and high feed grade periods. Installation of the columns has allowed the relatively coarse, well-liberated rougher concentrate and the relatively fine, low-grade scavenger concentrate to be treated separately, improving metallurgical performance in the cleaner circuit. Plant results show that the columns produce a high-grade concentrate at an average stage copper recovery of approximately 80 per cent. There is also indication of increases in both overall plant copper recovery and final concentrate copper grade. In addition, the operability and stability of the cleaner circuit has greatly improved.

Jan 1, 2007

By D. S. Loubser

The technique of backfilling in the gold mining industry is dependent on the dewatering of slurry to form a solid support system. In many cases flocculants are added to the slurry to increase the rate of dewatering. To ensure that a stable support is obtained it is important that the chemistry, application and limitations of these flocculant additives are understood. Flocculant additives have to be added at a point where minimum shear will occur. (Shear occurs when a flocculant is exposed to excess energy resulting in breakdown, of the floc.) To ensure that optimum results are obtained it is important that personnel involved are trained to use the flocculant additives and dosing equipment correctly.

Jan 1, 1988

By M. I. Brittan

SYNOPSIS The key reactions of the copper segregation process have been studied with a view to establishing the kinetics of the system. The investigation was carried out using two refractory copper ores from the Zambian Copperbelt in a small-scale, fluidized bed, chloridization reactor. The rate of chloridization of the copper in the ores is compared with the rate of volatilization of the cuprous chloride produced and with the rate of reduction of the cuprous chloride to form segregated metallic copper. In conjunction with available data on the rate of production of hydrogen chloride in a segregation system and with due regard to the conditions applicable in a TORCO reactor, it is concluded that the chloridization reaction is the major rate limiting step of the process. Factors influencing the rate of this extraction step and aspects of its mechanism are examined. The findings have confirmed the validity of the existing theory of segregation and provide insight as to the viability of the system of reactions involved in the copper segregation phenomenon. Experimental results which relate to observations made in the course of TORCO plant operation and segregation studies are discussed.

By H. A. D. Kirsten

The effects of the mining of deep-level tabular reefs are usually evaluated by use of continuum, elastic mining simulation analyses. This paper gives the results obtained from a series of analyses in which stopes of limited span are considered to be excavated in a non-linearly non-elastic, jointed and fractured rockmass. In particular, the theoretical influence of soft backfill in these conditions is evaluated. It is shown that the stress distribution and behaviour of the rockmass, alternately taken as an intact-elastic and as a fractured non-elastic medium, are completely different. The relevance of the energy-release rate commonly calculated in mining-simulation analyses, and the efficacy of its correlation with seismicity and the associated rockbursts, are reviewed. In deep-level mining operations, it is not practically feasible to obviate releases of seismic energy. The fact of their occurrence should therefore be accepted and, rather than considering the reduction of energy release as the primary objective, efforts should be concentrated on minimizing the effects of such release. Analytical results are given to demonstrate that this approach is not only correct, but also the only feasible solution to the rockburst-seismicity problem in deep mines.

Jan 1, 1989

By W. Wilmans

Electrokinetic dewatering of kimberlite slime under constant direct curents of 0,5 to 2 A and dewatering under constant applied potentia Is of 16,5 to 46,5 V are considered. The combined efects of electrophoresis and the addition of 8,3 x 10-3 M Mg2+ ions on the one hand, and 1 to 10 p.p.m. of the anionic polyacrylamide flocculant Praestol 2935 on the other, were investigated in a 3-litre Perspex electrophoretic cel. .The electro-osmotic dewatering experiments were conducted in a 3-litre Perspex electro-osmotic cel at various electrode spacings, as well as with a moving anode (top electrode). During electrophoretic dewatering, the zeta potential of the kimberlite particles did not change significantly, whereas the pH and temperature showed marked increases with time. The addition of Praestol 2935 enhanced the setling of the sludge bed owing to the additional effect of flocculation. The addition of electrolyte Mg (CIO4)2 retarded the separation process, partly as a result of gel formation in the slurry. During the electro-osmotic experiments, the rate of dewatering was found to be approximately proportional to the applied constant direct current, and to be independent of the electrode spacing. In general, electro-osmotic dewatering seemed to be more energy-efficient than electrophoretic dewatering.

Jan 1, 1987

By S R Grano

A fundamental model, which considers the subprocesses of particle collection by bubbles in flotation, is applied to two comprehensive flotation surveys in the rougher stages of C3 concentrator, PT Freeport Indonesia. The flotation surveys focused on the collection of: ? cell-by-cell and size-by-size metallurgical, ? cell hydrodynamic, and ? pulp and surface chemistry information. The two surveys were conducted at significantly different feed tonnages, giving rise to significantly different feed particle size distributions, pulp densities and mean pulp residence times. A series of model simulations are performed with the aim of quantifying changes in copper recovery, on both a size-by-size and unsized basis, with changes in values of the hydrodynamic parameters and hydrophobicity of the copper sulfide mineral. This was carried out in an effort to identify the most promising route to increase overall copper recovery in roughing. It was found that by increasing the hydrophobicity of the copper sulfide mineral surfaces it became possible to optimise cell hydrodynamics, which targeted increased fine (-12 µm) copper sulfide mineral recovery but without adversely affecting coarse (+150 µm) copper sulfide mineral recovery.

Jan 1, 2007

By Q. G. Reynolds

The dual-electrode DC arc furnace, an alternative design using an anode and cathode electrode instead of a hearth anode, was studied at small scale using computational modelling methods. Particular attention was paid to the effect of two key design variables, the arc length and the electrode separation, on the furnace behaviour. It was found that reducing the arc length to brush arc conditions was a valid means of overcoming several of the limitations of the dual-electrode design, namely high voltages and arc deflection.

Jan 1, 2012

By Y. Lizotte

This paper describes the design and implementation of the dispatching system at LAB Chrysotile Inc.'s Black Lake Mine Operation, Quebec, Canada. The initial system uses a computer in a passive role, to record and display information in ongoing operations. Simulation studies were undertaken at McGill University to assess various heuristic dispatching rules which can be program- med and inserted into the dispatching system. The computer can then suggest to the operator where a truck should be sent to maximize productivity or improve fleet efficiency. The study stresses the importance of considering the effects of implementing computerized systems on those individuals who must use these systems in their daily work. The roles of individuals from the industry and the university in this joint project are also highlighted.

Jan 1, 1987

Orebody modelling and reserve estimation are now subject to sophisticated procedures, but folded stratiform and stratabound deposits present particular problems in transforming coordinates of samples and blocks into their correct relative positions prior to deformation. In this paper an approach is taken whereby a geologically interpreted reference plane is used as a control. The study area is the Rio Tinto Minera copper mine near Santiago de Compostela, Spain. The transformation procedure on the 'unfolded' state is described, its limitations assessed and advantages considered.

Jan 1, 1987

By J. O. Claassen

A study was initiated and solutions implemented to address the root causes of a 30%?40% lower than predicted product yield achieved at a Mpumalanga coal mine. A holistic MRTM approach, which focused on improving exploration, geological sampling and analysis, geological modelling, planning, mining, and beneficiation practices, was used. The study indicated that deviations in the planned versus actual yields at the DMS plant were caused mainly by incorrect geological yield predictions, high and variable levels of dilution, and near-dense material, as well as the textural properties of the ore. Keywords MRTM, mining value chain improvement, Witbank coalfields, complex geology.

Oct 1, 2013