Search Documents

By J. F. Morrison, C. H. Wyndham, N. B. Strydom

INTRODUCTION The shovelling of rock in stopes is still a basic and important operation in many gold mines in the removal of gold-bearing rock from the stopes. There is, however, little factual knowledge of the factors which influence the the rates of energy expenditure and work output, and of the way in which variations in these factors, individually or in combination, affect the mechanical efficiency of the mine workers. What for example is the influence of different rates of shovelling, shovel loads and distances of throw? How does stope width and dip of the stope affect the mechanical efficiency of men shovelling rock? Recently a simple physiological test was introduced into the gold mining industry for classifying Bantu recruits into those capable of hard, moderate and light work. If this test is used to select only those Bantu mine workers who are capable of hard work for the task of shovelling rock in stopes then the rate of energy expenditure which could be expected from these men is 1.5 litres/min for the entire period of the shift. With an adequate knowledge of the influence of the various factors which affect the rate of energy expenditure of men shovelling rock in stopes it would be possible to set work standards for Bantu mine workers in stopes. This should be done in terms of the rate of shovelling, the shovel load and the distance of throw for any combination of width of stope, dip of stope, condition of foot wall and grade of rock in such a way that the resultant energy expenditure would be the 'optimum' that could be expected from the men but would be within their capacities for physical work of an endurance nature (that is, 1. 5 litres/min from the 'average' Bantu mine worker). Work standards could thereby be determined for the different stopes of a mine on a sound and systematic basis. In order to supply the information required a study was carried out by the Human Sciences Laboratory in which the work output and energy expenditures (in terms of oxygen consumption in litres/min) were measured on six highly trained Bantu mine workers under the following conditions: (a) rates of shovelling of 3, 4, 5, 6, and 10 shovels per minute. (b) loads of from 9 to 18 lb on the shovel. (c) distances of throw from 8 to 20 ft. (d) stope width of 28 in., 42 in. and 72 in. (e) dip of stopes of 0°, 15° and 30°. (f) rough and smooth footwalls and various grades of rock size. This paper gives the main results of practical importance of this study. Method The experiments were designed and conducted in conjunction with the Work Study Department of one certain underground conditions such as variable stope widths, stope angle, etc., were made available in a mine Surface Training School and suitable subjects were selected from the large number of labourers being put through the training school. Subjects Bantu recruits who had returned to the mine for a new contract and who had previous underground experience on shovelling were considered to be suitable as subjects for the experiments. The particulars of the subjects are given in Table I. TABLE I PHYSICAL CHARACTERISTICS OF SUBJECTS Weight Height Surface area Max O2 capacity Subject (Kg) (cm) (sq meters) (Litre/minute) A 71.5 167.3 1.80 3.5 B 61.5 162.3 1.65 2.8 C 63.0 164.1 1.69 2.4 D 66.5 167.4 1.75 2.8 E 70.2 164.6 1.77 3.0 F 77.8 173.1 1.92 3.8 Training The method of shovelling, accepted by the Work Study Department, was demonstrated to the subjects who then practised the movements with empty shovels, under the supervision of an instructor. After the technique was mastered, the men started shovelling rock and were trained for at least four hours per day to work at the higher shovelling rates. Training was continued for three weeks to enable the subjects to achieve a reasonable degree of physical training and conditioning. Shovelling method In both the kneeling and standing positions the subjects faced the pile of rock, grasped the shovel in the accepted manner and pushed the blade of the shovel into the base of the pile of rock, sliding the blade between the rock and the concrete floor. In the standing position (72 in. wide stope) the back leg assisted in the movement by pushing the knee against the back of the hand holding the shovel handle. In the kneeling position the elbow was tucked into the side of the body so that the muscles of

By A. G. W. Knock

Logistic curves are used in the prediction of the primary production of tin metal from estimated worldwide resources. Such curves are asymptotic to the total cumulative reserves, which are a function of prevailing metal prices and total resources. The figures for tin resources are based on the findings of Robertson and of Brobst and Pratt, the latter authors including estimates of undiscovered deposits. It is suggested that tin production will slump from the present level to 100000 long tons per annum by the end of the century, but will reach a new peak of 200 000 long tons some thirty years later. It appears that production will never exceed 300000 long tons per annum unless substantial new resources, excluding those predicted, are discovered.

Jan 1, 1979

COLLOQUIUM PRACTICAL APPLICATIONS OF INSTRUMENTATION IN THE MINING AND METALLURGICAL INDUSTRIES Rapporteur: J. Laschinger A colloquium and general meeting of the Institute held jointly with the Instrument and Control Society of Southern Africa at Kelvin House, Johannesburg on 18th October, 1972, had as its theme "Practical Applications of Instrumentation in the Mining and Metallurgical Industries" Dr J. P. Hugo (President) was in the chair and about 200 members and visitors were present.

By P. C. Seligmann

The theory of firing of electric detonators is developed insofar as it affects the design of blasting circuits. Practical values for the firing conditions suited to detonators of local manufacture are tabulated. The design principles of blasting circuits are outlined. This information can be used by mine management to ensure that electric blasting will be done efficiently and economically.

Jan 1, 1979

By K. R. Johnson

Changes in the pattern of computer systems for mine planning and geologic evaluation are occurring as a consequence of the introduction of 3-D high performance graphics terminals. The VULCAN system is described and an outline of its functionality is discussed. Increasingly, the integration of both database systems and graphics and databases will occur, allowing a greater degree of information access to mine operators. The system covers areas of database, drillhole graphics, mine design and layout, surface and solid modelling as well as reserve inventory generation. The design of the software is such that it is fairly commodity-independent and entirely menu-driven, to enable non computer-trained personnel easily to access the system.

Jan 1, 1987

By T. R. Marshall

SAMREC (The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves) Clause 7 notes that ‘Documentation detailing Exploration Results, Mineral Resources and Mineral Reserves from which a Public Report is prepared must be prepared by, or under the direction of, and signed by a Competent Person.’ Similar statements with respect to Competent Valuators (CVs) and Qualified Reserves Evaluators (QREs) are contained in the SAMVAL (South African Code for the Reporting of Mineral Asset Valuations) and SAMOG (South African Code for the Reporting of Oil & Gas Resources) codes respectively. What does it mean to be a Competent Person (CP) in the context of compiling/signing-off on SAMCODE (South African Mineral Code) compliant documents? What do the registration and experience requirements mean? Who is ultimately responsible for the report and what does such responsibility prescribe?

Sep 1, 2021

By D. J. de Clerk

Global trends stipulate the need to optimize existing assets while reducing environmental impacts. This paper illustrates the procedure that was followed to achieve such goals at one of the coal burning flash dryer units at an Anglo American smelter. An in-depth study of the process and related literature led to the development and installation of a revised control philosophy. This system includes modifications to the existing regulatory control structure as well as a hybrid rule-based and model-predictive advanced process control (APC) layer. Since commissioning of the APC, this flash dryer?s average throughput has increased by more than 6%, despite higher feed moistures. Furthermore, even though coal consumption has increased slightly, operating efficiency has improved by close to 5%. This was made possible by improving stability of the drying column outlet temperature by approximately 40%, which in turn enabled selection of a more optimal setpoint. Recent data has shown that APC utilization now exceeds 95%. This is indicative of a successful controller installation with good site acceptance. The same philosophy has therefore since been rolled out to most of the other flash dryers in the group.

Jan 1, 2012

By M. G. Atmore

As is usual when preparing for this type of occasion, I looked back at the subjects covered by my predecessors when they assumed the presidency of this Institute. You will appreciate that, in the eighty odd years since the Institute was founded, the diversity of subjects has been very great. In almost all cases it is quite natural that the speaker should have chosen a topic of special interest to him and one in which he was particularly knowledgeable.

Jan 1, 1979

By J. D. Koch

A 'project' is defined here as a process in which an idea is developed from its inception until either it is discarded or the product of the idea has been accepted by the ultimate user. The phases in a project, particularly the early phases, are examined, and project organization is described and contrasted with a functional line-management type of organization. Emphasis is placed on comprehensive definition, which is vitally important to the achievement of the goals of time, cost, and quality set for a project.

Jan 1, 1981

SACPE has asked the Journal to bring the following points to the notice of members who are about register with SACPE. When to Apply There is no set time to apply for registration. Engineers should apply when they believe that their training has met all the requirements of Policy Statement No. 1/3. Pitfalls Remember that it is the applicants' training that must be evaluated, and this requires the avoidance in the application of vague generalities such as 'My duties were design plant including its economic evaluation' or 'I was engaged in . . Requirements An example of what is required can perhaps best illustrate the point.

Jan 1, 1982

By R. W. O. Kersten

It was decided that Anglovaal should conduct a course on technical computing to help middle and upper mine management (40 years and older) to use computers. Background This decision was taken against the background of perception that various people have of computers and computer-related processes. People of the older generation Book review Rock mechanics for underground mining, by RH.G. Brady and E. T. Brown. London, George AlIen & Unwin, 1985. 527 pp. Reviewer: S. Budavari Mine safety awards The mining challenge of our time is the maintenance of the very highest safety standards, says a Chamber of Mines Executive. Haulage in surface mines An international symposium on 'Of-highway Haulage in Surface Mines' is to be held in Edmonton, Canada, from 15th to 17th May, 1989.

Jan 1, 1988

By W. J. Cruise

This paper reports on a test that was conducted underground in a mine for two years on the following: pipes coated with paint, fusion-bonded powder, metal, or impregnated tape; and aluminium, stainless-steel, 3CR12, and plastic pipes. It was found that the degree of corrosivity and mechanical damage increases substantially from the shaft of a mine towards the stope. Thus, the range of coatings that can be used successfully is fairly large in the shaft and haulageways, but corrosion-resistant materials, especially corrosion-resistant steels, need to be used close to the stope. A study of the relative costs involved showed the costs of pipes of low-carbon steel and unplasticized polyvinyl chloride to be lowest, and those of epoxy-coated steel pipes to be highest.

Jan 1, 1985

By P Clive Hart

DRA - BACKGROUND [MULTI MINERAL DESIGN & BUILD COMPANY FOUNDED 1984 ENGINEERING FOCUSED CORE ENGINEERING DISCIPLINES INCLUDE: ?PROCESS ?MECHANICAL ?E&I CONTROL PRIVATE COMPANY, INDEPENDENT & INTERNATIONAL]

Jan 1, 2006

By J. S. Freer

Two very successful schools on 'The design and operation of plants for the recovery of gold by activated carbon', were held from 14th to 18th October, 1985, and from 24th to 27th February, 1986, at Mintek. They were arranged by the Institute in close co-operation with Mr. Peter Bailey of Gencor, who was course leader. Computers and mathematics APCOM 87, the 20th International Symposium of the Application of Computers and Mathematics in the Mineral Industries, is to be held in Johannesburg from 19th to 23rd October, 1987. Interested people are invited to submit titles and synopses in any of the following topics or others. Papers can cover theoretical developments, practical applications, case studies, and software and hardware systems. Tunneling '88 The Institution of Mining and Metallurgy is pleased to announce the holding of 'Tunneling '88', the fifth international symposium and exhibition in the series, from 17th to 22nd April, 1988, at the Kensington Rainbow Exhibition Centre, London, England. Centenary exhibition and conference The major trade show to take place in the year of Johannesburg's centenary will be the 7th International Mining and Electrical Engineering Exhibition- ELECTRA MINING 86. The Exhibition, which is also the third-largest mining exhibition in the world, wil take place from 15th to 19th September, 1986, at the National Exhibition Centre, Crown Mines, Johannesburg. Mining electro technology The Eighth WVU International Mining Electro technology Conference is to be held in Morgantown, West Virginia, U.S.A., from 29th July to 1st August, 1986.

Jan 1, 1986

By T. A. Claasen

Exceptionally low yields in the coking-coal fields of the Soutpansberg area in the northern Transvaal, are taxing the skill and ingenuity of preparation engineers. The coals are highly intergrown, and a series of crushing and washing steps may be required to extract the maximum usable tonnage. In addition, novel preparation techniques may have to be employed. This paper, which is a case study of work recently undertaken, gives a general account of raw coal properties, emphasizing those related to maximum recoveries, and outlines the steps involved in the design of appropriate flow sheets based on laboratory studies.

Jan 1, 1980

By S. Z. Shkundin

An evaluation of the accuracy of tachometric and hot-wire anemometers in mine workings and gas-media ducts is given. The acoustic means of gas flow rates measurement is considered with particular reference to the equations of acoustic waves propagation in aerodynamic fields. The paper defines how it is possible to minimize the error of integrating acoustic anemometers.

Sep 1, 2001

By G. F. Balderson

In response to the written contribution made by G. J. C. Young to the above paper, I would like to make the following points. Paragraph 1 The build-up of oxidized coatings on cone surfaces has not been a problem in other applications similar to that at President Steyn. The following companies have commented.

Jan 1, 1982

By M. G. Spengler

A new type of pack has been developed primarily for the support of narrow stopes. It was shown in the laboratory that it has characteristics that very closely approximate the optimum required by underground support to achieve hangingwall stability.

Jan 1, 1978

By R. Watts, R. A. Laybourne

This paper describes how a 'mined out' coalfield is being mined successfully by opencast methods. The coalfield is that at New Vaal Colliery, which is situated in the Vereeniging-Vanderbijlpark-Sasolburg industrial complex. Al three coal seams at New Vaal had been mined previously, when the better-quality coal had been removed. The coal-preparation plant at New Vaal, which is also described, supplies coal to the 3600 MW Lethabo Power Station. The Colliery has been designed to supply 600 million sales tons of coal over its forty-year life.

Jan 1, 1990

Infacon 74 Members are reminded of the International Ferro-Alloys Congress that is to take place in Johannesburg between 22nd April and 1st May, 1974. The Congress is being held jointly by the National Institute for Metallurgy, the Ferro Alloy Producers' Association of South Africa, and the South African Institute of Mining and Metallurgy. Correspondence and enquiries should be addressed to The Secretary, Organizing Committee, INFACON 74, Private Bag 7, Auckland Park 2006. The gold deposits of the farms Lisbon and Berlyn in the Eastern Transvaal by v. c. H. R. BRERETON. Published in the Journal November 1973. AUTHOR'S CORRECTIONS The following amendments should be made.

Jan 2, 1974