Search Documents

By Stephen Krickovic

A methane emission rate study was conducted in 1969 on a longwall section of a Lower Kittanning coalbed mine in central Pennsylvania. The longwall face was mined with a drum shearer between developed headings on the head end and headings on the tail end that were driven with a ripper-type continuous miner as needed. The study was conducted over 22 consecutive shifts (7-1/3 days). The average methane emission rate from the Lower Kittanning coalbed during mining at the face and developing the headings at the tail end of the face was 34 Am. Caving of the gassy overlying strata as the result of mining at the face increased the methane emission to rates ranging from 702 to 1,049 cfm.

Jan 1, 1971

Develop methods of enhancing and measuring the high-temperature softening and melting properties of iron oxide pellets reduced under simulated blast furnace smelting conditions. Approach Add dolomite and Limestone flux and a low-cost organic binder, such as starch, carboxyl methylcellose (CMC), or waste papermill sludge, to the iron oxide concentrate to produce hematite (ferric oxide) pellets with superior high-temperature metallurgical properties. Simultaneous increases in softening temperature, gas permeability, and enhanced metallization rates are sought to improve blast furnace productivity and energy efficiency. Background In the past, bentonite, an inorganic binder, was the only additive (binder) used in the production of pellets made from iron ore concentrate. Research has shown that the reducibility of conventional (acid) pellets can be increased by the addition of flux or an organic binder. The increase in pellet reducibility results in less wustite in the center of the pellet at high temperatures, such as those obtained in the cohesive zone of the blast furnace.

Jan 1, 1990

By Noel N. Moebs

The Bureau of Mines measured surface subsidence above four small coal mine room-and-pillar sections in southwestern Pennsylvania, to obtain preliminary information on the magnitude and character of selected parameters, such as angle of draw and maximum subsidence, which are essential to the development of subsidence prediction methods. Data varied widely at the four sites; this is attributed to local geologic and mining conditions. Surface deformation at each site was of a magnitude normally associated with severe structural damage.

Jan 1, 1982

By E. K. Stanek, P. Kantabutra, R. A. Wolf

This paper summarizes the cause and effect of induced voltages in multiple conductor cables supplying alternating current power to equipment in under- ground coal mines. The investigation of this phenomenon revealed that the electrical energy produced by the resultant electric arcing between the frames of mobile electric face equipment was of a sufficient magnitude to ignite explosive methane-air mixtures. The results of laboratory tests and field tests made between equipment frames during actual operation in numerous coal mines are discussed. Several methods of eliminating or suppressing the induced voltages to nonincendive levels are also described. It is the purpose of this paper to convey to the mining industry a knowledge of this problem and to recommend methods of eliminating or reducing these induced voltages or arcing currents to safe levels.

Jan 1, 1975

By C. E. Jordan

The Bureau of Mines conducted tests on seven samples of Florida phosphate operations.slimes to develop a method to recover phosphate presently being discarded because of its small grain size. A system of hydrocyclones and hydroseparators was used to recover up to 96 pct of the plus 400-mesh material from the slimes. This plus 400-mesh material was subjected to fatty acid flotation, and concentrates containing up to 33.4 pct P205 were produced. As much as 88 pct of the phosphate (P205) was recovered from the plus 400-mesh material, and up to 29.6 pct was recovered from the total slimes.

Jan 1, 1982

Lower the respirable dust exposure of longwall shearer operators by keeping the dust cloud confined to the face. Approach Change the location of face-side machine cooling, water sprays. How It Works The dust breathed by the longwall shearer operator is usually produced by the shearer itself. The dust cloud originates at the face, and the exposure of the operator depends largely on how quickly this cloud spreads into the walkway. Water sprays on the shearer body can have a large effect on dust cloud spreading. Results to date indicate that sprays can help confine the dust cloud to the face if they are carefully placed. Otherwise they can make dust levels far worse. The worst offenders are often face-side sprays used to discharge cooling water from the cooling jackets of the shearer motors. These face-side sprays set up an air circulation pattern as illustrated in the drawing. Air induced by the sprays to flow towards the face, raises the air pressure in front of the face, which causes the air flow to turn and then move back over the shearer, bringing dust with it into the walkway.

Jan 1, 1981

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

By Ivette E. Torres

Bulk carriers, freighters, and tankers are the three classes of seagoing vessels engaged in transporting mineral commodities. However, vessels in these classes are not exclusively devoted to mineral commodity transport. Bulk carriers move considerable tonnages of agricultural products as well as crude minerals, their concentrates, mineral fertilizers, and the like. Freighters, owing to their great variety, can be devoted wholly to hauling mineral products or wholly to nonmineral goods, as well as carrying mixed mineral commodities and nonmineral commodities. They include general cargo ships, full container ships, partial container ships, roll-on/roll-offships, and barge carriers. Tankers, although largely engaged in moving crude oil and refinery products, also transport liquid chemicals, molasses, wine, liquefied natural gas, and other fluids. Although physical characteristics of vessels such as size, draft, crew requirements, type of propulsion system, ratio of gross tonnage to cargo tonnage, and fuel costs have undeniable influences on shipping industry performance, problems of and changes in the quantity and types of materials moved also significantly affect the shipping sector of the world economy, and thus have a bearing on the minerals sector of that aggregate. Unfortunately, comprehensive global data reflecting changes in these critical variables are not published.

Jan 1, 1994

Continuously monitor air-borne radon daughters that are a hazard to underground miners. Approach A beta detector continuously counts beta activity collected on a filter paper to allow calculation of exposure in working level units. How It Works At each Site a constant flow pump draws mine air through a fiberglass filter located in front of a beta detector (pancake type Geiger Mueller tube), Radioactive particles (products of the radon 222 gas emanating from the mine walls) collect on the filter and decay, releasing alpha and beta particles as well as gamma rays. A portion of the beta particles penetrate the Geiger tube window and create electrical pulses in the tube. These pulses are then amplified and sent by a coaxial type or shielded electrical cable to a central monitor located some distance from a working level detector. At the central monitor incoming Signals are amplified and fed into two channels, (See the block

Jan 1, 1979

Hang ventilating air curtains so that they can be installed, moved, opened and closed more easily than curtains that are spadded or nailed in place. Approach Low-leakage plastic curtains fitted with grommets along the top were threaded onto a steel cable which is suspended from roof bolt plates. The system was tested in two mines. How It Works The curtains are threaded onto a steel cable which is suspended from roof bolt plates by S-shaped hooks. See Figure 1. The outby end of the cable is reeled off a hand operated winch; the inby end of the cable is anchored to a roof bolt plate by means of a cable grip and an S-shaped hook. To install the curtains the following procedure is used. First, the winch is located at least 5 feet outby the last open cross-cut. The base of the winch can be secured to the mine roof with short roof bolts, only about a foot long.

Jan 1, 1978

By D. B. Gawthrop

"In connection with the proposed use of Cordeau-Bickford to fire L.O.X. (liquid oxygen explosives) in well drill holes, the question has arisen as to the effect of very low temperatures on (1) the rate of detonation of Cordeau-Bickford; (2) the sensitiveness to detonation of its TNT filling; and (3) the lead covering of Cordeau-Bickford.The Cordeau-Bickford used in this investigation was the standard 6 mm. size, such as is regularly used in blasting, and was manufactured and furnished by the Ensign-Bickford Company, Simsbury, Conn. All pieces tested were taken from rolls, all of which were from the same melted batch of TNT in order that all the pieces tested might be as nearly identical as possible.Different portions of this Cordeau-Bickford were tested plain (not countered), countered, and double countered. The countering and double countering was carried out by the manufacturer prior to shipment.The determination of the temperature at the instant of making a test was accomplished by the use of a Leeds and Northrup potentiometer and copper constantan thermocouples. Each couple was made from No. 28 B & S gage wire with short junctions. One junction was inserted in a hole drilled by a No. 60 drill through one lead wall of the Cordeau-Bickford to approximately the opposite wall, so that this junction was in the center of the TNT filling while the other junction was immersed in ice water. The potentiometer readings in millivolts were converted to °C. from the calibration curve of the thermocouple wire,"

Jun 1, 1924

By B. T. Brady

Results of a study are presented of the effect of low radial reinforcement pressure on the postfailure characteristics of two types of granite, a sandstone, and marble. The low radial reinforcement pressure is applied to the rock surface by a gooch rubber sleeve. The gooch rubber sleeve provides a radial pressure of less than 1 psi pressure to the rock surface. This method of support gives an average strength increase of approximately 8 percent to the fractured rock sample.

Jan 1, 1973

By H. M. Lawrence

The recovery of phosphate rack from the ores in the land-pebble district of Florida is a simple washing and screening operation. In the gashing plants coarse phosphate only is saved. Log-Washer overflows and screen-undersize products containing an appreciable content of fine phosphate are discarded. The phosphate grains in the material discharged to waste are generally finer in size than the mesh--14 to 20 mesh or 0.346 to 0.03 inch--of the finest screen in the washer. The operators state that the washers ordinarily recover from 50 to 60 per cent of the phosphate content of the matrix mined. Any increase that can be effected in the recovery of phosphate would be of advantage to the industry and would conserve the mineral resources of the country. In considering possible methods that might increase the recovery obtained in phosphate-washing plants the application of flotation, if it could be successfully developed, seemed to warrant investigation.

Jan 1, 1928

Provide an operator cab to assure protection, comfortable use of controls, and good visibility. Approach A cab which raises and lowers by pivoting about d horizontal axis was Installed on two S&S cleanup tractors and tested in two underground working mines. How It Works Hydraulic cylinders actuated by a lever inside the cab cause the cab to pivot about a horizontal axis. This action raises or lowers the cab height. The total cab excursion is 14 inches. A release valve in the hydraulic system allows the cab to lower automatically if struck by a roof load or overhead obstruction. The pivoting action of the cab is engineered so that the operator maintains comfortable use of all controls at all cab heights. The movement is such that the angular relationship of the operator's ankles With the tram and brake foot controls IS consistently within 90 to 100 degrees. Figure 1 outlines the approximate position of the operator at three cab elevations.

Jan 1, 1977

By Charles L. Kimbell

This study is intended to serve three roles. First, it is the second annual edition of this study in a separate volume that represents a global overview and summary to supplement and complement the five regional volumes that now constitute the U.S. Bureau of Mines international, geographically arranged studies. In this regard, it also extends previous works under this title that appeared in the inter-national volume of the Minerals Year-book from the inception of that volume (the 1963 edition) until it was subdivided into six separate volumes in 1989. Following the traditional format of past chapters under this title, the basic statistical presentations herein deal chiefly with 1990, and in a few instances with 1988 or 1989; these latter two only because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting on the world's mineral industry that have occurred between the end of 1990 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

Assist in controlling or extinguishing fires that occur in abandoned mine lands (AML) by providing a compilation of information on past fire control projects, the estimated extent of the current problem, and factors affecting the occurrence, propagation, and extinguishment of AML tires. Conventional fire control methods and their probable effectiveness are evaluated. Background Fires that occur in abandoned coal mines, waste banks, and coal outcrops constitute a serious health, safety, and environmental hazard from toxic fumes, deterioration of air quality, and subsidence. Although fires on AML occur in every coal-producing State, the severity of the problem varies, with most underground fires occurring in Kentucky, Pennsylvania, and Wyoming. Surface fires are prevalent in Kentucky, Pennsylvania, and West Virginia. Methods to extinguish or control AML fires, including excavation, fire barriers, and scaling, are generally expensive and have a relatively low probability of success (see figures 1 and 2). Bureau of Mines Study The Bureau compiled information from a variety of sources and found that the problem of AML fires is a serious one. Such fires can involve a high degree of hazard and can be difficult and costly to control. AML fires usually involve smoldering combustion in outcrops, waste banks, or abandoned mines. Given the nature of these fires, it is unlikely that the extent of the problem or the cost of solutions will decrease in the near future.

Jan 1, 1992

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

Validate the premise that there is measurable seismic activity associated with abandoned mint lands and that this activity can be used to determine stability of the abandoned mine openings, failure cycle of these openings, and susceptibility of the area to surface subsidence. Approach The U.S. Bureau of Mines conducted field investigations at two geologically contrasting sites, Colorado Springs, CO, and the Allegheny Portage Railroad Historical Site near Cresson, PA, to demonstrate that developing monitoring technology can be applied to any site. An array of seven geophones (velocity-measuring sensors) were strategically located to encompass an area at each site where failure in the underground mine openings could be expected, based on historical, geological, and engineering information. How It Works Bureau research has effectively demonstrated that stress changes within a rock mass can stimulate the development of cracks and fractures, resulting in the release of strain energy that generates seismic waves. These seismic waves, traveling outward from their source, can be detected, and the point of origin can be located in three-dimensional space. Furthermore, these seismic signals contain information that defines the source mechanism and the conditions between the source and the receiving sensor.

Jan 1, 1992

By Ann G. Kim

The Bureau of Mines investigated factors that influence the formation of methane and other hydrocarbon gases in coal, which is an integral part of the coalification process. Coalification begins with a biogenetic stage in which plant debris decomposes and peat is formed; methane and CO2 are the predominant gases produced during this stage. During the diagenetic stage of coalification hydrogen and the hydrocarbon gases methane, ethane, ethylene, propane, propylene, butene, iso-and normal butane, and pentane are formed by dissociation of the organic material. Methane may also be produced by a secondary reaction of hydrogen with unsaturates or by the reduction of CO2. The gas contained in coalbeds is a mixture of methane, C2 through C5 alkanes, CO2, O2, N2, H2, and He; its heating value is equivalent to that of natural gas. The gas content of coal depends on many variables, but an empirical relationship between adsorptive capacity, rank, and depth has been observed.

Jan 1, 1978

By Edward Thomas

"HISTORYThe origin of roof bolting as a means of roof support is obscure. During the past 23 years a method was developed by the. St. Joseph Lead Co: at its mines in southeastern Missouri, ranging from occasional use of single bolts with small bearing plates to systematic networks of bolts utilizing continuous bearing plates. Officials of this company are not certain which of its employees suggested their use. Many instances of occasional use of roof bolts have come to light during the past few years in widely separated mining districts, such as in West Virginia, Alabama, Illinois, Colorado, and Wyoming bituminous coal mines, and in Pennsylvania anthracite, Lake Superior iron, and Colorado lead-zinc mines. A few of the known installations have boon in place as long as 40 years.These installations usually were made to supplement wooden timbering in mine openings whore space was constricted, although it had been reported that roof bolting was started as a systematic moans of roof support in at least three instances but was abandoned because the cost of installation was excessive. The extra expense above that of conventional timbering could not be recaptured through economies resulting from increased efficiency, such as would be gained through mechanized mining.Roof bolting was first mentioned in mining literature in an article by W. W. Weige 3/ in Engineering and Mining Journal of May 1943, in which he described the use of bolts with 4-inch channel bearing plates in mines of the St. Joseph Load Co."

Sep 1, 1950