Search Documents

By E. A. Johnson

As part of its effort to reduce the environmental impact associated with mining and metallurgical operations, the Bureau of Mines used a modified form of the Environmental Protection Agency's Extraction Procedure toxicity test on copper reverberatory slags that contained low, medium, and high levels of the impurity elements As, Pb, Sb, Bi, and Zn. All tests resulted in extracts that did not exceed those limits published in the May 19, 1980, Federal Register; there-fore, these solid wastes were designated as nonhazardous for most landfill disposal situations. However, arsenic and lead levels disturbingly close to the allowable limits--and even higher levels of copper and zinc, for which there are no established limits--leached from the high-impurity-element granulated slags. These slags should be handled in such a way so as to minimize the possibility of water contamination. One baghouse dust was tested according to the EPA procedure and found to exceed the extract limits by a factor of 10. This solid waste may be considered hazardous.

Jan 1, 1982

By M. W. Von Bernewitz, E. H. Denny

The use of oxygen breathing apparatus during rescue and recovery operations at both coal and metal mines has become so commonplace that there is a tendency for the industry not to give such apparetus the full measure of credit that it deserves in any particular disaster , therefore , the data presented herein should give some idea of what has been done in this regard during the past 15 years that is , up to 1910 by the Technologic Branch of the U. S. Geological Survey , and thence ( to the end of 1922) by the U. S. Bureau of Mines .

Feb 1, 1923

By Edward Cogan

Equilibrium phase diagram studies of zirconium- rare earth metal alloys by the Bureau of Mines at its Albany Metallurgy Research Center prompted the development of a rapid gravimetric method for determining rare earths in zirconium in which the rare earths are absorbed from sulfuric acid solution of the alloy on a cation exchange resin . The sample in 10 percent H2SO4 is introduced into the column , the zirconium is eluted with 10 percent H2SO4 , and the rare earths are eluted with (NH4 )2SO4 solution and precipitated with NH4OH . A tracer technique was employed to determine the efficiency of the procedure . Y203 and europium 154 - 152 (Oak Ridge ) were added to 10 g of zirconium and taken through the entire procedure . Recovery averaged 97.6 percent on 0.002 μg europium in the rare earth fraction . Rare earths were determined in the range 0.10 to 90 percent .

Jan 1, 1964

By Thomas J. Fisher, John J. Sammarco, Gary L. Mowrey, Edward F. Fries

This report (Safety File 3.0) is the fourth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2002

By John J. Sammarco, Edward F. Fries

This report (Independent Functional Safety Assessment 4.0) is the fifth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2003

By F. E. Armstrong

The Bureau of Mines has conducted a research program to systematize the art of locating uncharted and lost oil and gas wells that penetrate coal seams; this publication presents a preliminary summary of its findings. Although no method or combination of methods will guarantee finding all uncharted and abandoned wells in a particular area, at least 75 percent of such wells can be located by compiling and applying all available information and using modern metal detectors.

Jan 1, 1973

By BUREAU OF MINES

Atentative Draft of a standard smoke abatement ordinance has been prepared by a joint committee made up of representatives of the American Society of Heating and Ventilating Engineers, the Stoler Mamufacturers Association, the American Civic association, and the Fuels Division of the American Society of Mechanical Engineers. The Committee is desirous of obtaining helpful criticism and suggestions about this ordinance, which should be mailed to the chairman, Dr. O. P. Hooi, Bureau of lines, ashington, D. C. Te personnel of the committee is as follows: Dr. O. P. Hood, chairman, and Henry Kreisinger, representing the Fuels Division of the American Society of Mechanical Engineers; P. J. Dougherty, representing the American Society of Heating and Ventilating Engineers; Lloyd R. Stowe, representing the Stoker Mam- facturers Association; Everett L. Hillard, representing the American Civic Ascociation; and Osborn Monnett and Harry 3. Meller, members at large.

Mar 1, 1930

[ ]

Jan 1, 2011

By A. Wahab Khair

"Geologic materials emit transient noises when stressed /1/. The rate and pattern of these transient noises or acoustic emissions (A.E. hereafter) depend on the stages of deformation of the material /2/. It has been demonstrated that rock/coal fracture processes under stress consist of three distinctive stages--crack initiation, propagation and ultimate fracture--and that coalescence of numerous cracks leads to ultimate failure rather than the propagation of a single crack /2,3/. This paper presents an analysis of fracture formation in rock/coal specimens subjected to straight wedge indentors using A.E. technique.The effect of specimen geometry, wedge indentor angle, confining pressure, and material anisotropy on fracture type (tension, extension, and shear crack), fracture length, and fracture intensity were studied. Two types of material mainly Berea sandstone and Coal Berg No. 2 coal were used in this study. Prior to the experiment the mechanical properties of both sandstone and coal were determined using rectangular specimen (Figures 1 a) in standard compression tests and are given in Table 1. In this study cylindrical and rectangular specimens were first prepared to proper dimensions of 2 in. x 1.5 in. and 3 in. x 1.5 in. x 1.5 in. (5.08 cm x 3.81 cm and 7.62 cm x 3.81 cm x 3.81 cm), respectively and then instrumented with SR-4 strain gages as shown in Figure 1. The instrumented specimens were then tested under four distinct load boundary conditions as illustrated in Figure 2. During a typical experiment the instrumented specimen was placed in a specially designed loading jig (Figure 3) where a predetermined lateral pressure was applied mechanically to the specimen by adjusting the inner plate of the confining chamber via screw while monitoring strains in the specimen. Using rock/coal elastic constants and measured strains, a predeter¬mined lateral pressure was applied to the specimen. Then a vertical load was applied by the straight edge of a wedge indentor attached to the upper platen of the universal loading machine via ball and socket arrangement (Figure 4). The arrangement allowed uniform application of load in a straight line manner on the surface of the specimen. During the test a number of parameters namely strains, load and A.E. rates were recorded (Figures 5a-b)."

Jun 1, 1988

By C. A. Herbert

Timber decay is due largely if not wholly to a fungus growth on the timber from which it derives' food; a warm, moist atmosphere is necessary for rapid growth. The decay is spread from infected timber to sound timber by countless microscopic spores or seeds given off by the fungus growth and carried by air currents or by long, cottonlike threads, which spread from timber to timber. Haulage roads in most mines in the central coal fields are also return aircourses; hence moisture and temperature conditions are ideal for the rapid decay of mine ties and mine timber. Possibly the return air, which contains a higher percentage of carbon dioxide than normal outside air, also stimulates the growth of fungi. Those familiar with coal mining have observed the more pronounced growth of fungi and decay of timber in poorly ventilated worked-out sections of mines where the air is moist and where usually the percentage of carbon dioxide in the air is considerably above normal.

Jan 1, 1934

By S. P. Kinney, A. C. Fieldner, S. H. Katz

"1 Introduction The regrettable death of James S. Cunningham, Foreman Miner, attached to Bureau of Mines Rescue Car No. 2, while wearing a half-hour type oxygen breathing apparatus in a gasoline storage tank at Trinidad, Colorado, raised the question as to the possibility of gasoline vapors permeating the rubberized fabric of the breathing bags of such apparatus.It is known that most gases and especially certain organic vapors permeate rubber, by solution or a similar process. The rubber becomes saturated with the gas and if a concentration of gas is maintained on one side of the rubber sheet it slowly gives off gas from the other side. It of course takes some time for the gas to diffuse through the rubber and the length of time before it reaches the other side is proportional to the thickness of the rubber. The amount of gas that passes through per unit of area in unit time increases with the concentration of gas and also varies with the structure and composition of the rubber.It has been suggested that the gasoline vapor could not have penetrated into the interior of an oxygen breathing bag because the pressure is greater on the inside, but this is not true as the process of permeation by solution in the rubber is affected only by the difference in the partial pressures of gasoline vapor on the inside and outside of the bag. The positive oxygen pressure on the inside can only prevent the entrance of gasoline vapor through measurable holes, and has no effect on permeation by diffusion through the rubber."

Dec 1, 1919

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Computer input data for an operating mine is developed on the basis of a detailed ventilation survey which includes air quantity, air quality, pressure loss and fan performance measurements. Quantity measurements must be reviewed extensively and assumptions made about leakage quantities and airflow paths. Pressure measurements must be reviewed and developed into a pressure gradient for the mine system. Air quality measurements are used to determine methane sources and amounts. Finally, the fan test data is used to develop the correct fan characteristic curve. Quantities and pressure losses for each branch in the system are used to calculate the branch resistances which are then utilized in the ventilation simulator to model the mine system. QUANTITY BALANCE The quantity of air coming into a mine based on field measurements will rarely equal the quantity exiting the mine, even if allowances are made for methane or compressed air input to the system. The same statement can be made for airflow through any isolated part of the mine ventilation system such as individual working section or main aircourses leading to an area isolated from the rest of the mine. The reason for the apparent discrepancies is the accuracy of the indicated quantities which in turn is based on the accuracy of the individual velocity and area measurements. Even with measurements following the guidelines described in the previous section on quantity measurement, this error can only be minimized but not eliminated. As a result the ventilation system must be carefully balanced so that, for any loop, the quantity in plus any methane or compressed air injection will equal the quantity out. The continuity of flow described by the balanced system must approximate the

Jan 1, 1977

By George J. Conroy

Techniques for locating trailing-cable faults are discussed, particularly those techniques suitable for use in underground coal mines, which have been the subjects of Bureau of Mines research. The discussion concerns precautions and suggestions for locating faults, rather than detailed descriptions of apparatus.

Jan 1, 1979

By E. E. Remmenga

Often a collection of analytical data, which should reasonably be expected to follow the normal distribution, contains too many extreme values, which the experimenter is inclined to eliminate according to some arbitrary procedure. The stepwise computer procedure described for this purpose is similar to many other truncation procedures; however, because truncation of a basically normal distribution causes a downward bias in the estimated variance, this procedure provides a graphical method to compensate for the bias.

Jan 1, 1971

By Henry M. Harris

The Bureau of Mines investigated a glass containing approximately 17 percent lithia and 83 percent silica to establish a method of devitrifying cast and rolled shapes. Glass shapes with high strength were made by melting, forming, and rapid cooling of the composition, and the shapes subsequently were converted to a crystalline condition by heat treatment. The best devitrification schedule included rapid cooling of the glass to below 300° C, followed by reheating at a rate of 50° to 400° C per hour, depending on the size of the shape, followed by a of 60 to 70 hours at 500° C and another period of 15 hours at 800° C. attempts to use faster heating rates or slow cooling to accomplish devitrification in deformation of the shapes. The crystalline shapes had flexural strengths that averaged over 33,000 psi, achieved with an annealing time of 60 to 70 hours at 500° C.

Jan 1, 1965

By J. N. Tomlinson

Trailing-cable splices are evaluated for moisture exclusion abilities after repeated travel over shuttle-car sheave wheels. Tests are conducted on cables with jackets made of neoprene, cholrosulphonated polyethylene (CSPE), and nitrile butadiene-polyvinyl chloride (NBR-PVC) to 50° C. The results show that some splice kits are effective as received, others are improved with minor but significant changes, and still others must be redesigned to be effective in underground applications. Laboratory results are compared with actual underground splice results. Recommendations for cable preparation prior to splicing are presented.

Jan 1, 1979

Provide a central source of subsidence reference in formation for industry, academia, and government agencies interested in improving subsidence prediction and analysis under U.S. mining conditions. Approach Develop a comprehensive bibliography about mining related surface subsidence and store this information in a computer file. Make specific references accessible through a key word retrieval program. Supplement these key word identifiers by entry of author's name, title of publication, subject of text, or sponsor of publication. How It Works Requests for subsidence in-formation are made by phone or mail to the Bureau of

Jan 1, 1982

By D. J. Bauer

Solvent extraction separation of light group rare-earth elements in a quaternary ammonium compound-chelating agent system was demonstrated in single-stage studies, Typical separation factor values obtained were 93 for lanthanum-praseodymium, 5.4 for praseodymium-neodymium, and 11.6 for neodymium-samarium. These values are significantly higher than those obtained using organophosphate extractants. Further studies in a 20-stage countercurrent mixer-settler resulted in the production of 99 percent lanthanum (oxide basis) at 96-percent recovery. Subsequently, 88 percent of the neodymium with a purity of 92 percent was recovered in the raffinate.

Jan 1, 1971

By Harry Dobroski, Larry G. Stolarczyk

A medium-frequency (MF) communication system has been built and has been tested in underground mines. It provides radio coverage to vehicles and personnel anywhere in the mine via parasitic coupling into existing mine conductors. The system consists of base stations, repeaters, and vehicular and personnel transceivers. Air-core antennas for vehicles and clamp-on antennas for base stations and repeaters were designed for maximum coupling efficiency using existing mine wiring. Personnel transceivers are of a unique vest design that features a low physical profile, good user comfort, and efficient antenna design. In-mine tests show impressive results. Range between rubber-tired vehicles and base stations is often measured in miles. With repeaters, greater range is possible.

By Edwin M. Thomasson

Helium shipments for 1965 exceeded the volume shipped during the previous year for the 16th successive time. Shipments from Bureau of Mines helium plants were 698.6 million cubic feet, 2 about 4.7 percent more than in 1964. Production at Bureau of Mines plants totaled 757.4 million cubic feet, and an additional 3,549.6 million cubic feet was produced by private companies participating in the helium conservation program and purchased by the Bureau of Mines and stored underground for future use. The Bureau of Mines continued to sell helium at $35 per thousand cubic feet, the price established in 1961. Production and sales of helium increased from the one private plant operating entirely outside the Government's helium program. A second private plant was virtually complete at yearend, although actual production had not commenced.

Jan 1, 1967