Search Documents

By Richard J. Mainiero, Harry C. Verakis

The Bureau of Mines has conducted research to determine whether the total elapsed delay time for blasting bituminous coal in underground mines could be safely expanded beyond the present 500-ms limitation without igniting a methane or methane-coal dust atmosphere. The results indicated that the increase of total delay from 500 to 1,000 ms had no detectable effect on safety relative to incendivity as long as permissible practices were observed in all other aspects. Research was also conducted to evaluate the safety of 18-in hole spacing for delay blasting in coal relative to misfires. For a variety of permissible explosives, misfires were observed for about 50 pct of the holes at 18-in spacing. Based on this observation, the Bureau has recommended that the new regulations prohibit hole spacings of less than 24 inches in underground coal mines. Misfires were also observed for 24-in spacing, but the number of misfires and test shots was too small to sup- port any firm conclusions.

By Paul E. Loustaunau, Devah Galloway, Catherine Wetherby

This report describes a project in which Development of a Supervisory and Management Training Program for the Underground Coal Mining Industry was developed and evaluated. The project was carried out in two phases. The first phase was a research effort to develop specifications for the program. The second phase was a development and evaluation effort. In the second phase, training programs for first-line supervisors (section foremen) and for middle managers (mine/shift foremen and mine superintendents) were prepared in accordance with the specifications and evaluated by members of the industry. This report describes the project and presents the conclusions drawn there from.

Jan 5, 1983

By J. S. Browning

The physical properties and specific gravity ranges of various liquids and salt solutions used for laboratory sink-float separations of rocks or minerals are presented. The test equipment and techniques employed by the Bureau of Mines in making sink-and-float separations of particles as coarse as 3 inches to as fine as 400 mesh are described. Also discussed are methods of recovering and reclaiming the liquids or salts from the minerals and wash solutions, as well as the hazards encountered and precautions to be followed while working with the materials. The laboratory use of various liquids for separating minerals of different specific gravities has been recognized for many years. During this time, laboratory sink-float procedures have proven their utility as a rapid and moderately accurate means for determining the mineral content of ores, test products, and plant products in certain nonmetallic concentrating operations, such as those producing mica, spodumene, kyanite, and so forth. These procedures also have been used as analytical tools for determining the mineral content and associations of other metallic and nonmetallic ores.

Jan 1, 1961

Identify abnormal low-frequency blast vibrations. Develop blast design procedures for such adverse vibration cases, including the selection of delay times based on ground conditions, vibration frequency, and structural response. The Problem Research by the Bureau of Mines and others has demonstrated how structural response and the potential for cracking and other damage depends on blast vibration frequency in addition to particle velocity amplitude. The Bureau has published recommended criteria for blasting near low-rise residential-type structures; criteria that specified frequency-dependent amplitudes. The typical vibration frequency from surface mine and quarry blasting is 20 hertz (Hz). Sites have been found, however, that regularly produce ground-roll-type waves with frequencies as low as 4 Hz. The most serious cases arc those where vibration frequencies fall in the natural frequency range for structures of 4 to 12 Hz. Such vibrations have a higher potential for causing, damage to residential structures, particularly at the low end of this frequency range, because of the resulting high strains these frequencies produce in structural materials.

Jan 1, 1990

By C. A. Rhoades

A major contributor to the problem of short life expectancy for blade-type conveyor belt cleaners is uneven wear along the blade edge. Uneven wear results in the formation of channels in the blade edge, which allow material to be carried back between the blade and the belt. In an effort to reduce the uneven wear problem, the U.S. Bureau of Mines has studied the mechanisms responsible for effective belt cleaning. From this study emerged a design for a cleaner blade that would greatly reduce uneven edge wear. The design consists of a standard cleaner blade incorporating air passages that allow for the expulsion of air along that part of the blade edge in contact with the conveyor belt surface. The results of 18-h tests indicated that the expulsion of air on the blade edge prevents scratches from developing into deep grooves. These tests showed that effective blade cleaning life can be extended 25 times using the pneumatic cleaning blade, compared with solid metal cleaning blades.

Jan 1, 1989

By John L. Hill

"The Bureau of Mines is conducting research on the causes and methods for control of cutter roof failure in underground coal mines. This hazardous ground control problem exposes miners to the danger of falling roof rock and frequently results in massive roof failure. This report outlines the probable causes of cutter roof failure, which are proposed based on field investigations, numerical model analysis, and in-mine observations. Traditional methods of control are presented, as well as innovative methods based on mining concepts developed during earlier years of coal mining history. The report can be useful to a mine operator for assessing the causes of cutter roof failure on a site-by-site basis and for predicting the probability of its occurrence. A process is presented for selecting an optimum control method that includes both traditional and innovative control techniques for each of the various causes of cutter roof failure. INTRODUCTIONGround control research conducted by the Bureau of Mines is designed to develop technology that will aid in reducing the frequency of accidents associated with poor ground control conditions. Cutter roof failure often poses a safety hazard to miners and causes delays in production while massive roof falls are cleaned up and unstable roof is resupported. Implementation of control measures reduces the threat of injury to miners and prevents production delays.The definition of cutter roof failure used in this report separates this unique type of failure from other ground control problems, to aid in the analysis of the causes and in the development of control methods. The definition is as follows:Cutter roof failure in mine roof rock is a failure process that initially begins as a fracture plane in the roof rock parallel to, and located at, the roof-rib intersection. The fracture propagates upward into the roof over the mine opening at an angle usually steeper than 60° from the horizontal.The mappable extent of cutter failure may range in length from only a few feet to several hundred feet and may traverse entry-crosscut intersections without change in direction. Once initiated along the roof-rib line, a cutter may propagate away from the roof-rib line of one side of a room, cross the roof span, and continue along the other side of the room. It is important to note that this definition excludes a similar type of failure (sometimes referred to as ""kink roof') that has comparable characteristics but occurs in the center of the entry. (The reasons for this distinction are discussed in the ""Background"" section.) Researchers refer to the cutter failure discussed in this report as ""classic"" cutter roof failure; except for short deviations across intersections and entries, initial failure is confined to the roof-rib intersection."

Jan 1, 1986

By David E. Emerson

The Bureau of Mines has developed a mass spectrometer method for deter-mining the helium-3 content of high-purity helium. The work was performed to evaluate experimental methods for removing helium-3 from high-purity helium and to better determine the composition of pure helium used in research. This was accomplished by increasing the inlet sample pressure, ionizing current, and amplification of the current produced by the ions collected on a conventional mass spectrometer that had been modified. With these modifications, the helium-3 content was determined in the parts-per-million and parts-per-billion range in helium-4.

Jan 1, 1976

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

The computer program has been developed in conjunction with the rest of the project to evaluate evacuation capabilities of the mines and develop guidelines for the escape systems. There are several problems associated with predicting evacuation performance of a mine. First, the mine has many interconnected passages, shafts, hoists and a number of miners in varying positions. To be able to predict evacuation time requires processing a hugh amount of data. A simplistic approach of determining the miner farthest from the exit and calculating evacuation time for him knowing his walking speeds and hoisting times is not realistic, since the waiting time for the hoist is neglected. The second problem is being able to repeat the calculations for a number of configurations. It may be possible to spend enough time to hand calculate the evacuation parameters for a single mine for a single configuration, but to evaluate capabilities of the evacuation

Jan 1, 1976

By Philip W. Holland

The Bureau of Mines has developed a trace helium analyzer for deter-mining helium-4 in the parts-per-billion range. The instrument is used for analyzing pure gases, laboratory-prepared standards, and atmospher-ic samples. Accuracy at the 95-pct confidence level in the 50-to 20,000-ppb range is within ±2 ppb or ±0.4 pct, whichever is greater. The minimum detectable helium-4 concentration is calculated to be 5 ppb. The analyzer consists of a modified helium leak-detector mass spec-trometer, a laboratory-built sample inlet system, and a liquid-nitrogen-cooled charcoal trap. A programmable integrator and event-control module make automatic operation possible. The portability of the analyzer allows it to be used in the field.

Jan 1, 1984

By Fred Leighton

The least squares method of rock noise source location presented is shown to be more accurate and reliable than standard direct solution methods. This method is particularly effective in improving solutions from rock noise locations outside of geophone array boundaries. A least squares solution for a medium .in which the seismic velocity is the same in all directions is also presented. In this special case, one can solve for both the source coordinates and the velocity.

Jan 1, 1972

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume- percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

SCOPE AND APPLICATION The rules cover the installation and use of electrical equipment in coal mines.- For generating stations, substations, lines, and equip¬ment aboveground, reference is made to existing rules covering such locations, viz, the National Electrical Code and the National Electrical Safety Code and any existing State or municipal regulations. The purpose of the rules is to set forth methods for safe electrical installation. In preparing the rules five basic measures for safe¬guarding the use of electricity in mines have been followed, viz 1. Remove the contributory causes of accidents or danger. 2. Remove from the vicinity of electrical apparatus all elements susceptible to the influence of electricity. 3. Keep the electric current where it belongs, if possible; if not, limit the area of its activity by protective devices. 4. Use a. large factor of safety in the selection, installation, and in¬ spection of equipment. 5. Have full control of the operation of electrically driven machines. Each rule that is given is proposed as necessary or helpful to the accomplishment of one or more of these measures. DEFINITIONS OF TERMS USED Alive.-See definition of " live." Approved.-The term " approved " means accepted as suitable by a competent committee, board, or organization designated by those adopting the rules. Authorized person.-The term " authorized person " means a per¬son appointed or permitted by the official designated by the State mining laws as the one in charge of the operation of the mine to carry out certain duties incident to the generation, transformation, and distribution or use of electric energy in the mine, such person be-

Jan 1, 1926

By S. R. B. Cooke

Certain saturated and unsaturated fatty acids and a variety of resin acids were used as collectors for specular hematite, magnetite, and goethite. Vacuum flotation tests were used with each collector and mineral to delimit the fields of flotation and nonflotation as functions of concentrations of collector and of hydrogen ion. The experimental results of these tests lead to the following conclusions. The respective fatty and resin acids exhibit characteristic fields of flotation and nonflotation for the three iron oxides. The fields are somewhat similar, and specular hematite apparently is the most floatable mineral. The insolubility of some of the organic acids may seriously restrict flotation at low pH, although the saturated fatty acids, caprylic and capric, collect minus-100, plus-150-mesh specular hematite only in acid pulp. The presence of a lower "critical pH" is explained on the basis of the dissociation and hydrolysis of dilute soap solutions.

Jan 1, 1959

By H. B. Carroll

The Bureau of Mines investigated the adaptability of the Meteorology Research Inc.2 (MRI) nephelometer and the Sinclair-Phoenix smoke meter for use in routine, analytical, smog-chamber experiments and to compare their responses to aerosol during these experiments. Both instruments' sampling systems were modified--smaller size sample input systems were studied using the nephelometer and a secondary sample system was added to the smoke meter to allow measurement of Aitken or condensate nuclei. Both instruments were easily adapted for use with small smog chambers and both displayed good precision and sensitivity to aerosol. A correlation was shown to exist between the two instruments' responses to aerosol. This correlation makes it possible to report the Sinclair-Phoenix measurements in visibility and/or mass units if desired.

Jan 1, 1973

By Thys B. Johnson

A three-dimensional dynamic programing method is presented for determining the optimal ultimate open pit limit. The method given is based on the block concept and is an extention of the two-dimensional Lerchs-Grossmann approach. The three-dimensional technique presented herein is fast and simple and may be used for an initial open pit evaluation when only limited data are available or as a more refined model when the entire deposit is well delineated. The method is illustrated by simple numerical examples and is also presented in algorithmic form. A computer program was written in Fortran IV which implements the three-dimensional algorithm and some computational aspects are discussed.

Jan 1, 1971

By G. R. Friggens

A nuclear method for continuously monitoring the coalbed and ash levels and void formation in commercial-scale, fixed-bed, pressurized gas producers is proposed. Measurement of gamma ray transmission through the coalbed is the basis of the method. The coalbed level is monitored by detecting the trans-mission of gamma rays from a 1 to 2 Ci Co-60 source positioned on the outside wall of the vessel. Coal bridging or, alternatively, ash level is monitored by a 10 Ci Co-60 source at the center of the coalbed. Source activities and geometries are calculated for a 12-foot-ID producer designed to operate at 350 psi. Source capsule and detector specifications and operational safety are also discussed.

Jan 1, 1973

By John D. Sullivan, Edward P. Barrett

The experimental work on the utilization of tin-plate scrap at the North- west experiment station of the U. S. Pireau of Mines in cooperation with College of Mines, University of Washington, necessitated the selection of a simple method for the determination of tin in the iron produced. Some of the standard methods for the determination of tin which were tried are given below: 1. Dissolving in acids and precipitating the tin as sulphide, igniting and weighing as Sn02. 2. Dissolving in aciis, reducing with nickel, cooling in an atmosphere of carbon dioxide, end titrating with standari iodine solution. 3. Dissolving in acids, precipitating the tin as sulphide, dissolving this sulphide in H3 and H2S04, heating until fumes of 503 are evolved, reducing with nickel or sheet lead, cooling in an atmosphere of carbon dioxide, ani titrating with a standard iodine solution.

Mar 1, 1923

By John C. Franklin

The Bureau of Mines conducted extensive laboratory and limited field tests to determine whether a polymeric material could effectively reduce the emanation rate of radon gas from uranium ore. In the laboratory 46 different single-coat materials and 14 two-coat applications were tested. The laboratory tests showed that up to 100 percent of the radon gas could be sealed into the rock. Materials tested in the laboratory were polyesters, furan resins, epoxies, latices, and totally inorganic coatings. From the laboratory work six different materials were selected for field testing. The first test was single-coat materials in five static chambers; the second test used two-coat applications in an open chamber. Both tests were conducted in the Dakota mine at Grants, N. Mex. During the second test, the amanation rate of radon gas was reduced up to 62 percent.

Jan 1, 1975

By M. D. Schlesinger

Experimental data for coal hydrogenation are presented to show that when a vehicle oil produced from coal is present, coal is hydrogenated to the same high conversion whether molybdenum catalyst is impregnated on the coal or intimately mixed with the slurry. Differences in product distribution could be related to the severity of operating conditions. No minimum mixing time was established, but 2 hours was sufficient. Longer periods of mixing, to 14.75 hours, had no effect on the results. The hydrogenation conditions were in the pressure range of 8,500 to 10,000 p,s,i. at 400° to 500° C. Most of the experiments were made in duplicate. The results were obtained with molybdenum concentrations of 0.01, 0.1, and 1 percent. Al the mentioned pressure range and a time at temperature of 15 to 60 minutes, coal conversions higher than 98 percent were obtained.

Jan 1, 1962

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The periphery of longwall panels in the Pocahontas No. 3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray sys tem.

Jan 1, 1974