Search Documents

Illinois has the largest reported bituminous coal resources of any state and is one of largest coal-producing states in the nation. Coal-bearing rocks underlie about 65 percent of Illinois, including all or part of 86 of its 102 counties. An estimated 18 1 billion tons of coal resources are still in the ground. Using present mining methods, more than 30 billion tons of coal are classified as recoverable. This represents almost one-eighth of the total recoverable reserves of all types of coal in the United States. The state's surface mining regulatory program was conditionally approved June 1,1982. It received full approval October 25,1988. The Abandoned Mine Land Program was approved June 1, 1982, and the AML emergency authority June 11, 1984.

Jan 1, 1992

By P. Coleman, J. C. Kerkering, S. Iverson

Fault tree analysis is a systematic safety analysis tool that proceeds deductively from the occurrence of an undesired event (accident) to the identification of the root causes of that event. One recurring mine safety problem—a dozer falling into a void over a drawpoint on a coal surge pile—was analyzed using available, inexpensive fault tree programs on a personal computer. The analysis identified basic and intermediate events that led to the burial of the dozer and graphically depicted the interrelationship between these various subordinate events as well as the various chain of events leading up to the primary event. A sensitivity analysis on these probabilities showed which events had the greatest influence on dozer burial in a coal surge pile.

By E. G. Davis

The flash reduction of fine iron ore in a dilute-phase system was investigated at 500° to 900° C within a heated stainless steel tubular coil. Alabama brown iron ore and Mesabi semitaconite ore were fed into the coil concurrently with reducing gases of hydrogen and reformed natural gas, so that the velocity of the gas at the reaction temperature was sufficient to entrain and pneumatically transport the solids through the coil. Reduction is very rapid with retention time of the ore in the coil varying from 4 to 15 seconds. Variables affecting reduction are temperature, ore feed rate, and gas flow or velocity. Results of the studies show that a partially reduced product (10-to 25-percent reduction) can be made which, on subsequent magnetic concentration, yields a concentrate containing 64 to 70 percent iron with a 90-to 94-percent iron recovery. Maximum reduction of 77 percent was obtained when hydrogen was used in a four-stage reduction test to yield a product containing 61 percent metallic iron.

Jan 1, 1972

By Maria I. De Rosa

Table 10 and figure 4 show the number of fires and fire injuries occurring at the surface of underground coal mines by state during 199&1999. Table 10 also shows by state the risk rate, employees' working hours, and lost workdays. A total of 65 fires occurred in 10 states. Thirteen of those fires caused 12 injuries and 1 fatality (the yearly average was 6.5 fires and 1.2 injuries). Four fues and one fire injury involved con- tractors. The Ewhr value was 97 x l O6 hr (Irr = 0.025); the LWD value was 6,206. Pennsylvania had the most fues (20 fues and 5 injuries), followed by West Virginia (1 6 fires and 1 fatality) and Kentucky (1 5 fires and 3 injuries). Among these states, Pennsylvania had the highest injury risk rate value (Irr - 0.095). Table 1 1, partly illustrated in figure 5, shows by time period the number of fires, fire injuries, and fire fatalities; risk rates; employees' working hours; and lost workdays. The number of fires and fire injuries show a decrease followed by an increase during the five time periods, accompanied by a decline in employees' working hours throughout the periods (see table 11 and figure 5). The Irr values follow patterns similar to those shown by the injury values. Tables 12- 17 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 6 shows the major variables during 199&1999. Table 18 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Noel N. Moebs

This report summarizes 10 selected Bureau of Mines research contract reports produced from 1970 to 1980 which consist largely of geologic studies of coal mine roof support problems. Significant highlights from the contract final reports are discussed and presented in practical terms. The selected reports focus on the Appalachian and Illinois coal mining regions. In the Appalachian coal region, two geologic structures, roof rolls and slickensides, predominate over all structures as features that directly contribute to roof falls. Studies of these and other structures are reviewed, and improved methods of utilizing drill core and core logs to prepare hazard maps are presented. Among the reports described are several on the weakening effects of moisture on shale roof, as determined from both laboratory and underground measurements, and an assessment of air tempering as a humidity-control method. Also summarized are findings concerning the time lapse between roof exposure and permanent support installation as a factor in the effectiveness of roof bolting.

Jan 1, 1984

By J. M. Kuchta

Ignition and flammability test methods were developed by the Bureau of Mines for use in the classification of flammable solids by the Department of Transportation. A rotating disk ignition apparatus and a flame-spread-rate apparatus are proposed for determining the ignitability and flammability, respectively, of most flammable solids. Extremely flammable solids, such as pyrophoric materials, are evaluated by determining their ease of spontaneous ignition in an environmental chamber at high-humidity conditions. Data are presented for various representative solids to show the reliability of the test methods for classifying the materials. A classification system is also proposed for use in government transportation regulations.

Jan 1, 1972

By M. J. Friedel, D. F. Scott, T. J. Williams

In an effort aimed at monitoring mining-induced stress changes that may influence ground failure, the US Bureau of Mines conducted a series of active 3-D seismic tomographic surveys at the Homestake (Lead, South Dakota) and Lucky Friday (Mullan, Idaho) mines. Existing rock bolts were used to mount geophones and as strike points for introducing seismic energy using a 3.6 kg sledge hammer. Travel time measurements were recorded spanning up to 160 m between drifts at several levels. The tomographic uncertainty was minimized by computing iso-velocity surfaces of constant probability based on statistics from multiple reconstructions and a threshold criteria. Periodic imaging using tomographic velocity surfaces demonstrated that temporal and spatial changes in the local stress field occurred in response to ground failure and stope advancement at a gold and silver mine, respectively. Keywords: Temporal imaging; Mine-induced stress; Seismic tomography; Geophysics

Sep 9, 1996

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global plate-tectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20° in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed.

By R. H. Sprute

This report describes a feasibility study to consolidate coal waste sludge in a 100-acre pond by applying direct current between floating and buried electrodes. The study was conducted by the Bureau of Mines under a cooperative agreement with Washington Irrigation and Development Co., located near Centralia, Wash. Part 1 covers results of laboratory tests at the Bureau's Spokane Research Center and a small-scale field test at the cooperator's coal preparation plant in western Washington. The process is efficient and cost-effective when power is applied at low current density. A proposed system, fully described in part 2, has electrodes covering 21 acres of pond surface radially arranged around a central power platform. Densification of pond contents would require 2 to 3 years of treatment. Total cost of equipment, labor, and material is approximately $500,000.

Jan 1, 1982

By H. E. Peterson

This report revises an earlier publication by the Bureau of Mines on tungsten analytical procedures and expands the coverage by including appropriate procedures for the critical impurity elements that commonly occur in tungsten ores and concentrates (13).3 The basic methods described are not original, but many of the modifications to improve reliability and sensitivity were developed by the Bureau. Gravimetric and colorimetric methods currently used for the determination of tungsten in ores, mill tailings, and concentrates are described. Colorimetric procedures are preferred for low concentrations of tungsten, whereas either procedure is satisfactory for moderate concentrations. Conversely, a gravimetric method is preferred for the determination of tungsten in concentrates.

Jan 1, 1963

By Richard F. Hewlett

This report describes a comparison of methods for computing grade and tonnage of ore, leach, and waste material for a mined-out portion of the Silver Bell Oxide porphyry copper deposit, and these computed values are compared with the actual tonnage of these classes of material produced during mining operations. Comparisons with production records have been made by using both exploration drill-hole assays and development blast-hole assays. The polygonal method is the most accurate for this deposit, because it more closely represents the lateral mineral distribution in the deposit. This is demonstrated by plots of the total-copper assay distributions of the development blast-hole assays for a specific bench. The investigation also shows that the smaller vertical assay interval (based on a 5-foot vertical churn-drill-hole sample) yields a more accurate estimate of both grade and tonnage than the 40-foot composite assay interval (based on the average of eight 5-foot assay values). This can be attributed to the fact that selective mining within a bench can separate out much of the waste and leach material that is included as ore in the 40-foot composite assay computations.

Jan 1, 1970

By M. L. Whisman

Radiotracer techniques were developed for stoichiometric studies of photochemical reactions associated with atmospheric smog formation. Stock blends of separate hydrocarbon and oxygenated compounds were prepared and calibrated. 14C-labeled reactants and products in reaction systems involving hydrocarbons and nitrogen oxides at the ppm level were analyzed for qualitative and quantitative data. Precision and accuracy of these methods developed by the Bureau were determined by replication and statistical treatment of data, and these methods are described.

Jan 1, 1969

By Jay D. Dixon

The Bureau of Mines has developed structural design data for unreinforced concrete tunnel linings for drifts used in block caving stopes. Design data are given that consist of moment, thrust, and deformation coefficients from which bending, axial, boundary stresses, and structural deformations can be determined at any point on the lining. Data is given for circular, horseshoe, and rectangular linings, each with two different thicknesses and subjected to eight different loading conditions for drifts excavated in hard and soft rocks. The structural analyses performed are based on procedures that account for both the structural behavior of the lining and that of the drift and take into consideration deformational interaction that occurs between them.

Jan 1, 1973

By Paul J. Barrett

The Bureau of Mines evaluated a sulfurous acid-sulfuric acid process for recovering alumina from clay, in which clay is leached. successively with sulfurous acid and sulfuric acid. The resulting aluminum sulfite and aluminum sulfate solutions are combined and heated to produce a basic aluminum sulfate and sulfur dioxide. Alumina is extracted from the basic aluminum sulfate as sodium aluminate by leaching with dilute sodium hydroxide. After desilication, sulfuric acid is used to precipitate alumina as alumina trihydrate, which is then calcined to alpha-alumina. The estimated fixed capital cost for a plant producing 1,000 tons per day of alumina is about $74 million on a 1971 basis. For comparison with previous alumina-from-clay evaluations, the estimated fixed capital cost for the plant is about $67 million on an M and S Chemical Equipment Index basis of 24.0.0, which is equivalent to a 1960 cost level. Because the operating cost is highly dependent on fuel and electric power costs, graphs are included to show the effect of these items on the operating cost. On a 1971 basis, with natural gas costing 35 cents per million Btu and operating labor costing $4 per hour, the estimated operating cost is about $100 per ton of alumina. On a 1960 basis, with labor costing $2.30 per hour and natural gas costing 25 cents per million Btu, the estimated operating cost is about $86 per ton of alumina.

Jan 1, 1973

By Frank G. Schwartz

The Bureau of Mines developed a rapid test method for predicting the stability of motor gasoline during long-term storage. The amounts of gum and inorganic residue formed in 13 gasolines during a l6-hour oven test at 200° F were compared with the amounts formed in the same gasolines stored at 110° F, and analyzed following 8-, 16-, 32-, 44-, and 52-week storage periods. Satisfactory methods were developed for predicting gum and inorganic residue formation during fuel storage periods as long as 32 weeks at 110° F, the approximate equivalent of 5.7 years at 80° F. The only data required to apply the methods are the amount of gum and inorganic residue formed, and the amount of oxygen that reacted, during a l6-hour oven test. A direct relationship existed between inorganic residue formed during the oven test and during 110° F storage. Statistical treatment of the data showed predicted values were as reliable as determined values. By use of a modified Arrhenius equation, the 110° F storage time can be extrapolated to equivalent time at any temperature below 110° F. Thus by combining the stability prediction method with the mathematical extrapolation, the storage performance of motor gasoline for extended periods can be estimated at any temperature up to 110° F.

Jan 1, 1968

By S. J. Page, W. R. Reed, J. A. Organiscak

NIOSH continues to conduct respirable dust control research for surface mine blasthole drilling operations. Research areas have included testing variables (shroud leakage area, drill deck cross-sectional area, shroud height, collector-to-bailing airflow ratio, etc.) that have the most impact on respirable dust control, development of a dust collector inlet hood, development of a dust collector dump point shroud, and testing of a small diameter water separating sub. This paper summarizes the results of the aforementioned research that has been completed. Additionally, past dust control research for drilling operations of both underground and surface mines completed by the U.S. Bureau of Mines, created in 1910 and incorporated into NIOSH in 1997, is reviewed.

By Nicholas G. Theofilos

Ecuador's real gross domestic product (GDP) increased 6% in 1976 despite persistent shortages of electrical power and essential fuels, which caused factory slow-downs and shutdowns. Petroleum export earnings, which made up more than 50% of total export value in 19716, totaled $565 million, a 9% increase over those of 1975. A new 60,000-barrel-per-day oil refinery at Esmeraldas was scheduled to go on- stream in mid- 1 97 7, operating entirely on Ecuadorean crude. Corpración Estatal Petró1era Ecualtoriana (CEPE) started construction of a 600-kilometer network of product pipelines which was scheduled to be completed in 1977 to coincide with the completion of the refinery.

Jan 1, 1980

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines(USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two formulations resulted in stable gels that lasted for at least 12 months in the mine. Semi continuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both interms of productivity and enhanced mine safety.

Jan 1, 1995

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

Data or input files are used to describe the mine's ventilation system and physical characteristics necessary for ventilation calculations as well as the physical or mechanical disturbance to be modeled and simulated Data files are organized into lines of categories or groups of information Each line contains multiple sets of information or data items Data lines are read by the program, and the data items provide information to the program variables The data file is in American Standard Code for Informa¬tion Interchange (ASCII) format, sometimes called a DOS text format Creation or modification of a data file is accomplished with text editor software Most word pro¬cessors are also capable of making the required ASCII type files A sample data file and its associated output are included in appendix B. When selecting software for editing the data files, the user should be aware that the software will also be used for viewing the output of the simulation The output file can be quite large (several megabytes), if a lengthy simulation is performed The output can be sent to a printer for a hardcopy fisting, however, the user should also be aware that most printers currently used with PC's print at rates of 100 to 300 characters per second and large output files may take several hours to print Viewing the output with a text editor can save much time and paper DATA FILE MANAGEMENT The data files describing the event and mine to be simulated can reside either on a floppy disk or in a directory on the hard disk drive When the program starts, the user is prompted for the data file location and name The user response is in the form of a standard DOS path and file name For example, if the data file is on a floppy disk located in drive B and the disk has a directory MYMINE with the data file MYDATA DAT in that directory, then, at the prompt

Jan 1, 1990

By T. G. Carnahan

The Bureau of Mines investigated a flotation-nitric acid leach procedure as part of the goal to maximize minerals and metals recovered from primary and secondary domestic resources. Studies were conducted on an ore that contained carbon-bearing and sulfide mineralization that rendered a portion of the ore refractory (resistant) to conventional leaching technology. The procedure investigated for treating the ore consisted of the following: (1) separation by flotation of the carbonaceous and sulfidic components from the ore, (2) leaching the flotation concentrate with nitric acid at 100° to 110° C, (3) leaching the flotation tailings with sulfuric acid, and (4) processing the combined leached slurries in a conventional manner to recover yellow cake. In step 2, HN03 is converted to gaseous products from which it is regenerated by reacting these products with air and water for further leaching. An overall uranium extraction of 96 pct was achieved by this procedure.

Jan 1, 1979