Search Documents

By W. G. Pariseau

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mine in the Coeur d'Alene Mining District of northern Idaho. The present study uses rock deformation measurements to validate and calibrate a geomechanical model of the experimental Lucky Friday underhand longwall (LFUL) stope on the 5,100-ft level of the Lucky Friday Mine, Mullan, ID. The calibrated three-dimensional, finite-element model and measurements of rock mass displacement show a correlation of 0.795. The calibration reduces rock mass modulus to 14 to 17 pet of laboratory values and rock mass strength (with an energy rule) to 37 to 41 pet of laboratory values. This model suggested that stress-related ground control problems would be encountered west of the stope where the vein makes a right-angle turn and then splits. Rock burst activity was concentrated in this area during mining of the LFUL stope.

Jan 1, 2010

By L. C. George

Addition of an acid waste to an alkaline cyanide waste was investigated for five different combinations of electroplating wastes. At the optimum final pH values of the mixtures, metals and cyanides were almost quantita¬tively precipitated. No evolution of hydrogen cyanide was detected by a few additional processing steps, significant amounts of variable metals were recovered for recycling the waste-plus-Waste step is attractive because no reagents are required, metals arc concentrated, and a relatively harmless effluent that meets most water quality Standards for cyanide content is produced.

Jan 1, 1970

By A. F. Cohen

When location guidelines are followed in choosing sites for fixed point velocity transducers for use in underground coal mine monitoring, mine air turbulence intensities <11% are generally expected at those sites. The objective of this Bureau of Mines investigation to determine the effect of turbulence intensities <11% on vortex shedding sensors and transducers. Measurements were made at velocity levels of interest for underground coal mine monitoring use (?200, ?500, ?1,000, ?1,500 ft/min). The effect of grid-produced turbulence intensities (2% to ?14%) on the output of vortex-shedding air-velocity transducers was less than ±10%.

Jan 1, 1985

By R. V. Ramani, V. T. Burgos, J. A. McClay

General The underground mining environment has traditionally been hostile and as early mines were developed, coal seams with particularly difficult natural conditions were bypassed in favor of those more easily exploited. Barring the discovery of new and novel sources of energy, the depletion of petroleum and natural gas reserves will eventually force the United States back to the use of coal as its primary energy source. Figure 1 illustrates the trend away from coal which has taken place over the past half century. Today, the demand for coal requires a re-evaluation of all coal seams to meet the needs of the energy market. Difficult mining conditions may result in an increase in the consumption of roof control materials, require greater investment in pumping and ventilation systems, and increase the need for in-depth engineering of far greater safety in production plans. They may also cause delays in mine development and curtail production, all of which combine to drive up the unit production cost. It is reasonable to expect that conditions will continue to deteriorate as current reserves are depleted, thus bringing this factor into greater prominence in the future. For several years now, it has become apparent that in addition to economic objectives, coal companies must set and achieve several concomitant objectives to accomodate society&apos;s interest in the conservation of natural resources. Government action to meet this interest has taken the form of two categories of Federal legislation, environmental protection and employee health and safety. The effects of both of these have not been fully evaluated with respect to the total economic picture, although preliminary evidence indicates that an immediate increase in

Jan 1, 1975

By Foster Fraas

Calculations based on data related to the electrostatic precipitator illustrate the variation in the electric forces on a particle with change in position in the ionized field. The feeble forces in some separators are explained by the low field intensity at midpoint locations between the electrodes. When the particles are in contact with the exterior surface of a rotating cylindrical electrode, a high field intensity at the electrode surface combined with the image charge results in large electric forces. The permissible feed velocity increases as the square root of the electrode diameter, providing high values in efficiency and feed rate capacity, particularly in surface-to-mass ratio separations such as are encountered in secondary materials recycling operations.

Jan 1, 1971

By James V. Kelly

During the winter of 1946 and the spring of 1947, the Bureau of Mines conducted an investigation and drilling program in the vicinity of the village of Fairplay, Wis. Fifteen diamond drill holes totaling 2,457.6 feet of bore were completed. This work was part of a general study of the zinc-producing area of southwestern Wisconsin and had the particular purpose of investigating a structural trend, determined by the Federal Geological Survey, in an area some distance from known ore bodies or active mines.

Jan 1, 1948

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide bauxite production capacity by mine and country, including bauxite substitute materials in countries of the former Soviet Union, The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1994. Capacity data represent announced installed and planned capacities and do not necessarily reflect a U.S. Bureau of Mines judgment of actual mine operating levels or timing of planned expansions. The year-end capacity is the ?in place? capacity or estimated production capacity, whichever is larger.

Jan 1, 1994

By J. D. Marchant

The Bureau of Mines studied solid-state electromigration to determine the value of the technique as a method of purifying cerium metal. Cerium metal in bars 6 inches long and 1/2 inch in diameter was refined at 600° C by solid-state electrolysis to remove iron, copper, and manganese. Iron and manganese were electrotransported to the anode and copper was electrotransported to the cathode. The concentration of iron at the anode of a cerium bar was 800 times greater than the concentration at the cathode. The concentration of manganese at the anode was twice the value at the cathode. The concentration of copper was 170 times greater at the cathode than at the anode. A radiotracer technique was used to follow the iron migration in the cerium metal. Molybdenum, silicon, and aluminum impurities were not electrotransported.

Jan 1, 1967

By A. W. Newberry

The Virginia copper district is situated in North Carolina and Virginia. It contains many mines and prospects that were active at the turn of the nineteenth century. The Bureau of Mines, as part of the strategic-minerals program, began a project in September 1942 to investigate and explore the most promising of the mines in the district. The Seaboard, High Hill, Durgy, and Blue Wing mines were the sites of the main project activity. This report deals principally with these four mines. Drilling did not discover any new ore shoots but indicated the persistence of known ore shoots in depth. There appears to be no indication of impoverishment of copper with depth.

Jan 1, 1948

By Stephen P. Holt, John A. Bowsher

A preliminary examination of the mica deposits in Culberson and Hudspeth Counties , Texas , was made in September 1942 by A. B. Needham, district engineer of the Bureau of Mines . The deposits were reexamined by R. C. Redfield , associate mining engineer of the Bureau in November 1942, at which time he was accompanied by Philip S. Hoyt , geologist , and J. C. Moore , foreman of the Texas Mica and Feldspar Company . Exploratory work was started on February 16 , 1944 , and terminated on April 30 , 1944. A crew of 4 to 10 men was employed under the supervision of the authors .

Feb 1, 1947

By Joseph J. Wallace

1. From the standpoint of known recoverable reserves, the following is the order of importance of the beds: Upper Kittaoning, Lower Kittanning, Upper Freeport, Lower Freeport, Middle Kittaning, Clarion, Pittsburgh, and Redstone. 2. mown measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, me estimated at 1,859 million short tons as of January 1, 1952. Of this, 1,351 million short tons me in beds 28 inches and more thick. Areas in each bed were omitted from the estimates because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By B. K. Shibler

During the investigation of the occurrence of manganese deposits in the Western United States, examining engineers of the Bureau of Mines collected 2-ton samples from five manganese properties near Golconda, Nev. Extensive laboratory tests were made to determine the amenability of these ores to standard ore-dressing methods of concentration. The Tom Major property, one of those sampled, is situated 12-1/2 miles south of Golconda, Humboldt County, Nev. The deposit is described as a bed about 5 feet thick in a thinly bedded shale and dolomite formation. The sample tested was obtained from the manganese bed, but the examining engineer reported: "The mining of an appreciable tonnage at reasonable cost would perhaps cut in half the grade represented by the sample."

Jan 1, 1951

By James C. Cawley

This National Institute for Occupational Safety and Health study was conducted to focus future research on the most significant electrical problems in the mining industry. Data from 1,926 mine electrical accidents (including 75 fatalities) that occurred between 1990 and 1999 were studied. Coal and metalnonmetal operator- and contractor-reported data are presented. All data used in this analysis were MSHA closeout data, except 1999, which were preliminary data.

By L. L. Rethi

The U.S. Bureau of Mines summarized injury data for independent contractor employees working at all locations of coal and metal-nonmetal mines from 1983 through 1990. During the eight years, the greatest contrast in degree of injury between independent contractor and operator employees was in fatalities. From 1983 through 1990, there were 132 independent contractor employee fatalities in the mining industry. In 1988 though, independent contractor employees accounted for nearly one-fourth of all mining fatalities. The fatality incidence rates of independent contractors were consistently higher than those of operators during the eight years. For instance, in 1990, the contractors&apos; rate was twice that of operator employees in coalmining and nearly five times that of operators in metal-nonmetal mining. Three other salient facts highlight the independent contractor employees&apos; fatality injury data during these years. First, 82% of the independent contractor employee fatalities occurred at surface locations. Second, two job classifications?truck driver and equipment operator?represented 37% of the fatalities throughout the 8-year period. And finally, four accident classifications?powered haulage, slips and falls, machinery, and electrical?accounted for 71% of all independent contractor employee fatalities.

Jan 1, 1993

By G. W. Grove, H. R. Burdelsky, F. E. Griffith

"INTRODUCTION The work of using a system of air locks in unsealing a mine in Ohio following a fire probably was one of the outstanding jobs of its kind in a medium-thick coal bed.The fire in this mine, thought to have been of electrical origin, was discovered at about 1:30 a.m. on December 11, 1941. Forty-four men were working in the affected section at the time; 5 escaped unassisted, and 37, who had barricaded themselves, were rescued. The bodies of two men, who had succumbed after breathing fumes given off by the fire, were brought part way out of the mine before it became necessary to seal the mine.Direct attempts to extinguish the fire with water were abandoned when hazardous amounts of 'carbon monoxide, methane, and other inflammable gases were detected in return air passing through the main haulageway and escape-way of the mine.The mine was completely sealed on the surface at about 8 p.m. on December 12, 1941, with the two bodies remaining in the mine. Sixteen days after the mine had been sealed, the two bodies were recovered. This was accomplished by air-locking through a partitioned-off stairs compartment of a ventilation shaft. This work was done under adverse barometric and atmospheric conditions.A method for collecting representative air samples from the immediate fire area was used successfully by utilizing a vacuum pump on about 10,000 feet of existing water line that had been broken near the fire area.The immediate fire region was sealed, and confined to a relatively small area; the remainder of the mine was recovered, and operations were resumed February 9, 1942, or 59, days from the time of sealing the mine on the surface. This recovery was made by air-locking the main entries inby from the shaft and No. 2 right-face entries.The distance between air locks averaged about 500 feet, and as each new set of seal stoppings and air locks was completed, the old or outby seals were taken out and the area between was ventilated. In ventilating this area, it was often necessary to use line curtains to direct the air into dead-end places."

Oct 1, 1947

By E. Shekarchi

The mineral industry of Afghanistan improved substantially in 1976 as asbestos production was begun and feasibility studies were made of possible copper and iron and steel industries. The remarkable event of the year was the introduction of Afghanistan&apos;s 7-year economic and social development plan which covered the years 2976-82. The 7-year plan established ambitious goals for a gross national product (GNP) annual growth rate of 6.3% during its duration. To achieve this target, large increases in expenditures for economic development were programed in virtually every sector of the economy. Foreign assistance, in particular, was expected to finance a large share of new development projects. The major components of the plan were the development of transportation (highways and railroads), oil and gas exploration, construction of a copper smelter to exploit the copper deposits near Kabul, and development of an iron and steel industry to exploit the rich iron ore deposits in the central part of the country. Exports during the plan period were to continue to be principally agriculture products and natural gas to the U.S.S.R.

Jan 1, 1980

By R. W. Lewis

Spectrochemical procedures were developed using dc arc excitation for the determination, in parts per million, of 18 impurity elements in electrorefined beryllium and high-purity beryllium oxide. The metal samples were dissolved in dilute hydrochloric acid, evaporated to dryness, and converted to the oxide in a muffle furnace at 900° C. Germanium oxide was added as an internal standard for the determination of 15 of the elements, copper oxide for boron and molybdenum, and neodymium oxide for calcium. The average coefficient of variation was 11 percent with the exception of copper, which averaged about 43 percent.

Jan 1, 1962

By S. M. Molloy

The postwar demand for insulating material such as mineral wool, in-creased in proportion to the rapid construction of new buildings, placing an enormous burden on the existing mineral-wool industry both in known sources of raw materials and in available plant facilities. In view of the increased demand on the industry, the Bureau of Mines in its Mississippi Valley Experiment Station" Rolla, Mo., undertook an investigation to aid the industry by establishing resources of raw materials through actual laboratory wool-blowing tests and by developing certain methods for evaluating the physical proper-ties of a mineral wool. As material was received from the public, laboratory-evaluation technique had to be developed, the results of which would reflect in the mineral-wool-industry standards. The methods of testing used by the mineral-wool industry, not only would have required a pilot-plant installation capable of producing a large tonnage of mineral wool, but each wool-blowing campaign would have been very expensive and necessitated considerable personnel and equipment. The present laboratory wool-blowing equipment can produce as high as eight wool-blowing campaigns a day. The nature, simplicity, and size of the physical testing equipment permit testing as small a sample of wool as 25 grams and give information as reasonably accurate as in a 40-pound bag of wool. The purpose of this report is to describe the laboratory method of production and the evaluation of the physical properties of small quantities of mineral wool. Considerable work has already been done, and the interest of the public and industry is measured in the number of samples being submitted for testing.

Jan 1, 1948

By L. B. Pankratz

Present-day interest in the rare-earth elements and their compounds, for both metallurgical and ceramic uses, makes it highly desirable to accumulate basic thermodynamic data that can be applied to theoretical considerations of the processing of these substances. Such data still are seriously lacking. This Bureau of Mines paper reports the results of high-temperature heat content measurements of the sesquioxides of four rare-earth elements--europium, gadolinium, neodymium, and samarium--and of the closely related element, yttrium. The temperature ranges covered by the measurements are as follows: Monoclinic Eu2O3, 298°-1,802° K. Cubic Eu203, 298°-1,350° K. Monoclinic Gd203, 298-1,802° K. Cubic Gd203, 298°-1,550° K. Hexagonal Nd203, 298°-1,795° K. Monoclinic Sm203 298°-1,798° K. Cubic Sm203, 298°-1,149° K. Cubic Y203, 298°-1,799° K.

Jan 1, 1962

By Chase E. Sutton

The porosity of a sand is usually the measure of its capacity for holding fluid, although porosity is sometimes selective; that is, a small percentage of the actual pore space (voids), particularly in fine-grained sandstones, may be isolated by the cementing material which prevents the entrance of fluids under normal conditions. Obviously, however, porosity determinations are essential to an engineering study of underground conditions of an oil field, and a simple and reliable method of obtaining a reasonably accurate figure for average porosity is desirable. This report describes a method suggested by Ruasell,3 which was used by the writer in the preparation of a report on the Texhoma-Gose pool, Archer County, Tex.4 The conditions in this pool were particularly favorable for obtaining an average porosity figure, in that some 30 to 35 core samples of the pay sand were available for analysis.

Jan 1, 1928