Search Documents

By Charles C. Myers, Robert M. Doerr

The apparatus described was developed for determining the kinetics of gas - solid reactions at high temperatures by measuring the volume of gas consumed with respect to time . This apparatus consists essentially of a horizontal precision- bore glass tube connecting a small reaction chamber in a furnace to a large constant - temperature reservoir . A drop of mercury in the tube separates the two sides of the system and serves as an indicator that moves at a speed proportional to the rate of gas consumption . The sensitivity of the apparatus depends inversely on both the density of the gas in the system and the cross - sectional area of the tube ; with a tube having an area of 0.079 cm² , the sensitivity for oxygen at 308 ° K and 0.5 atm is 20 cm/mg . The reproducibility of data with the volumetric apparatus is good .

Jan 1, 1964

By Roy L. Wilfong, LeRoy R. Furlong, Louis P. Domingues

The bulk and apparent densities , particle size , and surface area of ceria powders derived from the ammonium sulfate , carbonate , nitrate , oxalate , and sulfate salts and heated at 950 ° to 1,500 ° C for 1 to 24 hours were studied . The bulk and apparent densities and particle size generally increased , and surface area decreased with increase in temperature and time of heating ; surface area was more sensitive to changes in temperature and time than the other properties studied . These properties of the ceria powders had a marked dependence on temperature and a lesser dependence on duration of heating at a given temperature ; and the source of oxide and thermal treatment cannot be considered optional in the preparation of refractory powders by thermal decomposition . The ammonium sulfate and sulfate salts heated at 950 ° and 1,200 ° C produced oxide powders with the lowest bulk density , the smallest particle size , and the highest surface area . The highest apparent densities were achieved for oxides resulting from the carbonate and the sulfate but the carbonate - derived material was considerably coarser . The surface areas of ceria powders derived from cerium salts decrease in the order of sulfate , ammonium sulfate , nitrate , oxalate , and carbonate . The observation of these physical properties are useful in predicting the sintering behavior of various oxide powders .

Jan 1, 1964

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, Which in Many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over wide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals now being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the same for all of the tars studied. Also, it mast function equally well for both low and high temperature tar permit accurate fractionation, and reduce adventitious decomposition to a minimum. The authors are aware that certain types of distillation analysis which do not meet the above requirements may give results comparable with those of the large stills of a by-product coke-plant where one type of tar is produced. These may be simpler and shorter and entirely suitable for control work, but at the same time have little value in a fundamental investigation.

Jan 1, 1932

By D. Harrington

"In order to stimulate general interest in mine safety among their employees the mining companies of Butte, Mont., instituted in 1918 a Miners' Field Day, and this field day has since been held annually about the end of July, the last one being on July 25, 1921. The mining companies of the Butte district finance this meet in proportion to the number of men employed at the time of the meet, the contributing companies with number of working force, end proportional contributions for the opening field day in 1918 being given below:COMPANY NUMBER EMPLOYED AMOUNT CONTRIBUTEDAnaconda Copper Mining Co.,12,500,$ 1,078.53Butte & Superior Mining Co.,1,800,155.32North Butte Mining Co.,,1,294,111.67East Butte Copper Co.,,850,73.36W. A. Clark Interests,,600,51.78Davis-Daly Mining Co.,,340,29.35,,,,17,384,$ 1,500.00*Note: In many mining districts it is now the custom to hold an annual Miners' Field Day. The field day, as a rule, is financed principally by the mine operators, and was instituted primarily to promote interest among miners in the ""Safety First"" movement. Usually demonstrations or contests in first aid and mine rescue are the leading feature of the day's events, which include games, races, dancing, and all the other amusements usual to a gala holiday. Thus the field (ley serves the double purpose of stimulating interest in mine safety and promoting cordial relations and community fellowship. This paper is an interesting account of the way in which the Miners' Field Day in the Butte district is organized, with data on costs, plan of organization, method of conducting, and the practical benefits derived from it. - Ed"

Oct 1, 1921

By M. M. Tilman

The purpose of this investigation was to determine the effects of small amounts of cobalt in nickel on the tensile properties and hardness of representative types of austenitic stainless steels . Cobalt substitutions for nickel up to 2 weight - percent were made in types 302 and 309 stainless steels . Data were obtained at room temperature for tensile strength , yield strength , percentage elongation , percentage reduction in area , and hardness . In type 302 steels , tensile strength and hardness increased with increased percentages of cobalt , percentage elongation and reduction in area decreased , and yield strength showed little change . Property changes were largely due to the reduction of nickel content rather than to the addition of cobalt . In type 309 steels , only minor variations were observed for the properties investigated ; the effects of the relatively snall cobalt substitutions and nickel reductions were somewhat reduced by the higher total alloy content .

Jan 1, 1964

By Irving Hartmann

The record of safety in the use of permissible explosives in United States coal mines has been excellent, due in great measure to the persistence with which research has been carried on in the Bureau of Mines, to the development of permissible explosives, and to the cooperation of mine operators and workers in using permissibles in a recommended manner and in the effective though gradual replacement of black powder and other nonpermissibles. The demand for increased rate of coal production, changes in mining conditions and minim methods, and introduction of new mining machinery have resulted in modified or new blasting practices. To keep abreast of these developments the Bureau of Mines conducts investigations under actual mining conditions at the Experimental coal mine near Pittsburgh, Pa. Several years ago an extensive study was complete to determine conditions under which the allowable charge limit for permissible explosives per shot hole might be raised from 1.5 to 3 pounds without undue risk of gas or coal-dust ignitions. As a result of the study, this increase in the charge limit was authorized under certain specified conditions in 1948,5/ greatly facilitating production schedules.

Jan 1, 1954

By A. J. Kraemer

"During the past several years a great deal of discussion has centered around the question of the permissible limit of sulphur content in fuels for automotive and aviation motors. Under certain conditions of operation, sulphur in motor fuels causes the formation of corrosive substances which attack bearings, wrist pins, and other parts of engines. On the other hand, in making gasoline from certain stocks, the gasoline fraction normally contains a relatively large proportion of sulphur compounds. By the generally used processes of reducing the sulphur content, a significant part of the gasoline fraction is lost as motor fuel, and added expenses are entailed for chemicals, labor, and other process costs. This condition has been an economic burden to some refiners of high-sulphur crudes. In some instances the treating losses have been rather severe and the treating costs relatively high, but the data presented in this paper indicate that the reduction of sulphur content of motor fuel is a problem to a relatively small number of refiners and of little or no concern to the remainder; in fact, more than 90 per cent of the 153 samples analyzed passed the Federal specification requirement, Which limits the sulphur content to 0.10 per cent. 3This report is based upon the results of an examination for sulphur content, Doctor test, copper strip corrosion, and color of the samples collected during January, 1930, for the twenty-first semiannual gasoline survey of the Bureau of Mines. The results of the gravity ad distillation tests of the survey were published as Report of Investigations 2995. The numbering of the samples given in this report is the same as in Report of Investigations 2995; for example, No. 25 of this report is the same sample as No. 25 of Report of Investigations 2995."

Jun 1, 1930

By R. E. Kennedy

The presence of combustible gases and vapors in air can constitute n extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and. allied industries, the U. S. Bureau of Mines has investigated the explosive properties of a number of gaseous and liquid compounds; the results of these investigations have been published in various government papers and journal articles. The increased use of liquefied, petroleum gases has intensified interest in the effect of high pressures on the explosibility of propane-air mixtures. The limits of flammability of natural gas-air mixtures have been determined at pressures ranging from 50 min. Hg to 3,000 p.s.i. As it is known that a combustible. gas or vapor cannot burn or explode when the oxygen content of the atmosphere is less than a certain value, critical values were determined for the oxygen content of atmospheres to which nitrogen had been added as a diluent. In this connection limits of flammability were determined for ethane in atmospheres containing added. nitrogen or carbon dioxide at pressures up to 900 p.s.i.g.

Jan 1, 1951

By L. Allan White

Instrumental analysis is an indispensable tool to many phases of research on rare-earth metals and their compounds; therefore, the development of new and improved instrumental techniques is essential. This report describes an emission spectrometric analytical method using direct-current carbon-arc excitation of various rare-earth-oxide mixtures. Lanthanum oxide serves the dual purpose of an internal standard and a constant major constituent. The versatility of the method was demonstrated by three different applications: (a) Analysis of complex rare-earth concentrates; (b) determination of impurities in high-purity rare-earth oxides; and (c) detection of rare-earth elements in other types of matrices, such as those resulting from beneficiation of rare-earth ores. The average error of analysis in the concentration range of 0.2 to 10.0 percent was 14.6 percent for a group of complex synthetic mixtures of rare-earth oxides. An average error of analysis in the concentration range of 0.05 to 0.50 percent was 21 percent for a group of high-purity rare-earth oxides.

Jan 1, 1959

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By H. P. Greenwald

"INTRODUCTION In the course of its studies of the explosibility of various coal dusts in the Experimental coal mine, the Bureau of Mines has tested coals representing the entire range of volatile content found in the United States. In connection with their work the Bureau's field engineers some¬times meet operating officials who are not impressed by the fact that there is an explosion hazard in mines working low—volatile coals. Actually the difference in explosion hazard between high—volatile and low—volatile coals is one of degree and not of kind. The purpose of this paper is to set forth briefly the experimental evidence that has been accumulated on the explosibility of coal dusts containing 8 to 31 percent volatile matter on a dry, mineral—matter—free basis.There have been numerous dust explosions in mines in which coals were worked that have compositions within this range. Those explosions are listed in an appendix, together with a bibliography of Bureau of Mines papers describing explosion tests in the Experimental coal mine."

Jan 1, 1940

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, which in many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over vide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals nor being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the sane for all of the tars studied. Also, it must function equally well for both low and high temperature tar, permit accurate fractionation, and reduce adventitious decomposition to a minimum.

Jan 1, 1932

This volume summarizes the contract work performed over a nine-month period by Westinghouse Electric Corporation on a Cost Plus Fixed Fee Contract for the Department of Interior's Bureau of Mines. The contract has been extended primarily to carry out improvements recommended for equipment produced under the contract for communicating with and locating trapped miners. These improvements will enhance the performance and utility of this equipment for operational use in actual mine emergencies. An additional complete set of the equipment will also he furnished to the Bureau under this extension. The work of the basic contract was to design, produce and test hardware in accordance with the Westinghouse response to a Bureau of Mines Request for Proposal which was based technically on recommendations of a study performed for the Bureau by the National Academy of Engineering (NAE). The NAE study made suggestions for new equipment in three areas of need:

Jan 1, 1971

By Robert D. O'Brien

"INTRODUCTION The Miscellaneous Minerals Division of the War Production Board requested the Bureau of Mines to investigate the Gallatin corundum property as a possible source of corundum, which was in short supply due to the war. The Gallatin corundum property, also known as the ""Fuller mine"", the ""Montana Corundum mine"", and as the ""Old Qorundum mine"" was first examined by a Bureau of Mines engineer 2/ in July 1943. Bureau of Mines work on the property started October 11, 1943, was recessed May 5, 1944, and was resumed in October 1944 when the diamond-drilling program started. The project was completed February 7, 1945. The data obtained are given in this report.The Federal Geological Survey made a reconnaissance survey in the spring of 1943 and mapped the area the following autumn. The results of these surveys are contained in a memorandum report prepared in December 1943.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Aug 1, 1947

By G. R. Hopkins

According to reports received by the United States Bureau of Mines, Department of Commerce, as of January 1, 1929, there were 2,205 cracking units completed or being built in the United States, with a total daily charging capacity of 1,476,874 barrels. A similar survey of a year ago showed 2,334 units of 1,288,000 barrels total capacity. This indicates that despite a decrease in. number of units, there was a material increase in capacity. The year 1928 was, in general, an important one for the cracking branch of the industry. Gasoline consumption reached record levels, prices were higher than in 1927, and it is probable that in the late months of the year the cracking plants were operating very close to capacity.

Jan 1, 1929

By K. K. Kershner

The purpose of this investigation was to develop methods on a laboratory scale for recovering tin from metallurgical slime, Tin chlorides were volatilized using mixtures of hydrogen chloride and reducing gases, such as hydrogen, carbon monoxide, hydrogen sulfide, ethane, propane, and butane. Optimum conditions were found to be n mixture of 3:1 of hydrogen and hydrogen chloride at 475° C. Over 95 percent of the tin was volatilized as chlorides. Low temperatures and relatively rapid rates of reaction are distinct advantages of the chloride volatilization process. Research is being continued with various slimes and will be extended to tin ores, where the method offers interesting economic possibilities in comparison with current tin-smelting practice.

Jan 1, 1957

By Richard C. Ballance

Fly ash from four sources and in certain proportions was shown to assist chemical coagulation of turbid water and settling of chemically induced floc. Fly ash reduced the time required to form the first visible floc, promoted more uniform flocs about 2 mm in diameter, and increased the mean settling rate of floc particles. Also, the addition of fly ash produced denser sludges than those obtained with alum alone. Final turbidities were independent of fly ash particle size and carbon content. Optimum proportions of fly ash additive are given.

Jan 1, 1966

By Eric R. Bauer

This U.S. Bureau of Mines study was conducted to gain a basis for recommending methods to predict and prevent the occurrence of cutter roof failure, a common ground control problem in mines of the Northern Appalachian Coal Basin. This was accomplished by determining the geologic and engineering factors responsible for cutter development at six mines affected by cutter roof failure. Three distinct factors were found to be initiators of cutter roof failure: (1) high horizontal roof stress, (2) surface topographic variations, and (3) geologic anomalies. Effective control of cutter roof was obtained through improved bolting techniques, entry and mine reorientation, and entry and pillar size modifications, but only when selected based on the actual cause of failure.

Jan 1, 1990

By Hugo E. Camargo

In an effort to reduce Noise Induced Hearing Loss (NIHL) in the mining industry, the National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for mining equipment whose operators exceed the Permissible Exposure Level (PEL). The process involves three steps: 1) Noise source identification (NSI), 2) development of noise controls, and 3) evaluation of the developed noise controls. For the first and third steps, microphone phased array measurements are typically conducted and data are processed using the conventional beamforming (CB) algorithm. However, due to the size and complexity of the machines, this task is not straight forward. Furthermore, because of the low frequency range of interest, i.e., 200 Hz to 1000 Hz, results obtained using CB may show poor resolution issues which result in inaccuracy in the noise source location. To overcome this resolution issue, two alternative approaches are explored in this paper, namely the CLEAN-SC algorithm and a variarion of an adaptive beamforming algorithm known as Robust Capon Beamformer (RCB). These algorithms were used along with the CB algorithm to process data collected from a horizontal Vibrating Screen (VS) machine used in coal preparation plants. Results with the array in the overhead position showed that despite the use of a large array, i.e., 3.5-meter diameter, the acoustic maps obtained using CB showed "hot spots" that covered various components, i.e., the screen deck, the side walls, the I-beam, the eccentric mechanisms, and the electric motor. Thus, it was not possible to identify which component was the dominant contributor to the sound radiated by the machine. The acoustic maps obtained using the RCB algorithm showed smaller "hot" spots that in general covered only one or two components. Nevertheless, the most dramatic reduction in "hot" spot size was obtained using the CLEAN-SC algorithm. This algorithm yielded acoustic maps with small and well localized "hot" spots that pinpointed dominant noise sources. However, because the CLEAN-SC algorithm yields small and localized "hot" spots, extra care needs to be used when aligning the acoustic maps with the actual pictures of the machine. In conclusion, use of the RCB and the CLEAN-SC algorithms in the low frequency range of interest helped pinpoint dominant noise sources which otherwise would be very hard to identify.

Jan 1, 2009

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-MM-scfd, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 mi 11 ion tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of May 12, 1974, under the terms of the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 and early 1974 indexes . Initial capital investment varies: $45,358,600 for the 4.8-million- ton-per-year (MM tpy) mine in the Eastern province, $54,603,000 for the 6.72 MM tpy mine in the Interior province, and $29,871,000 for the 9.2 MM tpy mine in the Northern Great Plains province. Total capital invest-ments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $61,070,000, $76,753,000, and $56,286,000, respectively. Corresponding selling prices for the coal, per ton, are $4.79, $4.23, and $2.66, assuming a 12-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1974