Search Documents

By J. M. Singer

The objective of this investigation was to determine minimum air velocities and entrainment rates for coal and rock dust dispersion in wind tunnel experiments under conditions that simulate dispersion from surfaces in coal mines where airflows are induced by weak gas explosions. Dust deposits were bed-or ridge-shaped; particle sizes were 6 to 80 microns (cohesive deposits) or 100 to 150 microns (free-flowing deposits); and wind tunnels were 7.62 cm wide by 5.08 cm high by 300 cm long, and 2.4 m wide by 1.5 m high by 215 m long. The investigation showed that minimum air velocities (directed at mid-height) of separate, layered, or mixed piles of coal dust and rock dust were within the range 5 to 30 m/sec, independent of size of wind tunnel. This finding considerably facilitates scaling of data to mine-size passageways. Free-flowing deposits dispersed relatively slowly by single-particle detachment; cohesive dusts dispersed faster by the breaking and lifting of large clumps along weak failure flames; particle dispersion occurred in flight. Layered or mixed deposits of coal and rock dust did not disperse selectively. Semiempirical expressions were derived relating minimum air velocities and dispersion rates to dust-pile geometry, cohesion, porosity, and bulk density.

Jan 1, 1972

By T. F. Tomb

Past experience has shown that the penetration characteristics of the 10-mm nylon cyclone used on approved personal sampling equipment are significantly different from those determined in the laboratory using a nonpulsating flow source. The Bureau of Mines has developed and recommended a modification to presently approved equipment that will alleviate this difference. However, as a result of this modification, a new relationship for converting respirable dust concentrations measured with approved personal sampling equipment to equivalent concentrations as measured with an MRE instrument will have to be established. This Bureau of Mines report describes the underground sampling program conducted to establish a new factor for converting respirable dust concentrations measured with personal sampling equipment, modified with a recommended pulsation damping device, to an equivalent concentration as measured with an MRE gravimetric dust sampler.

Jan 1, 1973

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By B. R. Eichbaum

To develop technology to assure an ample supply of zinc and to reduce environmental pollution, the U.S. Bureau of Mines investigated alternatives to the roast-leach process for treating complex sulfide concentrates. Previous studies proved that low-grade zinc sulfide (ZnS) concentrates could be leached using chlorine-oxygen to produce zinc chloride (ZnCI2). The process involves high energy requirements for evaporating the pregnant solution to produce anhydrous ZnCl2 needed for electrolytic cell feed. An efficient hydrometallurgical process would facilitate treatment of lower grade ores than can be used in conventional processing and would render roasting unnecessary. An alternative method was devised for recovering ZnCl2 from solution. Zinc diammine chloride [Zn(NH3)2CI2] was precipitated from solution by adding ammonium chloride (NH4CI) and sparging with ammonia (NH3) to a pH of 6 to 7.5. The spent solution was treated with calcium hydroxide [Ca(OH)21 at 60° to 80° C for 1 to 4 h to remove remaining zinc and NH3. The Zn(NH3)2CI2 was heated to 300° to 400° C to remove NH3 and produce anhydrous ZnCI2. A possible flowsheet was devised and is included.

Jan 1, 1991

By R. K. Franklin, S. T. Reese, J. J. Forbes

"INTRODUCTION It is a recognized fact that in the coal-mining industry coal dust must be allayed to promote the safety and health of underground workers. The Bureau of Mines has been cognizant of the hazards of coal dust for many years, and the necessity of controlling such dust was acknowledged when the Federal Mine Safety Code was formulated. Accumulations of coal dust increase the explosion hazard in a bituminous-coal mine and facilitate the propagation of an explosion. Some of the coal dust produced in mining is inhaled by the workers and contributes to respiratory infection. Impairment of vision and personal discomfort resulting from working in dense clouds of coal dust reflect unfavorably on the efficiency of workmen. Considerable coal dust, originating at the working face, is carried in the ventilating current and deposited elsewhere in the mine, thereby increasing the explosion hazard. It is apparent, therefore, that if coal dust could be allayed effectively at its points of origin, the dust-explosion hazard in bituminous-coal mines would be reduced greatly.Although dust control is practiced in many bituminous-coal and lignite mines, the extent and effectiveness of control for the, entire industry-is not generally known. The purpose of this circular is to present such information clearly, and to encourage coal-mine operators to install dust- allaying equipment.Factual data on dust-allaying practices at working faces in a large number of the bituminous-coal and lignite mines in the United States were .compiled from reports on recent Federal inspections of these mines, The information is presented in tabular form to permit review of the dust-allaying practices of a substantial part of the industry, by States, and also according to employment, and loading practice."

May 1, 1950

By Robert S. Schechter

A minitest of the new potassium chloride-potassium carbonate two-stage in-situ uranium leach process has been carried out at the Intercontinental Energy Corporation (IEC) Zamzow project site in South Texas. Substantial quantities of high concentration uranium were produced indicating the viability of the leach solution. The test results yield information regarding the reservoir dispersivity, the average cation-exchange capacity of the formation, and the distribution coefficients describing cation-exchange reactions. The test also indicates permeability anisotropy and the existence of disturbed flow fields.

Jan 1, 1985

By A. L. Johns, M. V. Healey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of tie laws of Ecuador has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State..

May 1, 1930

By Francis Church Lincoln, Paul Zinner

"Attention of the Bureau of Mines was first directed to the Gray farm area by the results of several exploratory churn-drill holes completed by the New Jersey Zinc Co., and later by Roland J. Teske and by Judge H. L. Heer.When the Bureau of Mines initiated its investigation of the area, all drilling on the Gray farm had been discontinued, and no mining had resulted from the exploratory work. However, in the opinion of the Illinois Geological Survey, the Federal Geological Survey, and the Federal Bureau of Mines, this drilling,with the preliminary geological studies, was considered sufficient evidence to justify continued exploration to the southeast along a projection of the trend of mineralization developed in the mines to the northwest, or the so-called Black Jack Trough.This report describes the work done and presents the data obtained during the period of Bureau of Mines exploratory work.In its program of exploration of mineral deposits, the Bureau of Mines has as its Primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision or Dr. R. S. Dean, assistant director.Special acknowledgment is due Paul Herbert, geologist, Illinois Geological Survey, for his studies of cores, which greatly influenced the planning and progress of the exploratory work. Acknowledgment is also made to A. F. Agnew and A. V. Heyl, geologists, Federal Geological Survey, for their invaluable aid; to 0. W. Terry, F. C. Lincoln, M. H. Berliner, A. M. Cummings, project engineers; and to E. P. Barrett, district engineer, Minneapolis, and E. D. Gardner, regional engineer, Rolla, Mo., for supervising the program.The Gray ore body is on the Gray farm 5 miles south of Galena in Jo Daviess County, northwestern Illinois. The location with respect to adjoining properties is shown on figure 1. Galena is a city of 4,000 population on the banks of the Galena River, a stream that was formerly navigable by Mississippi River steamers but has now shrunk to the dimensions of a small creek. A gravel road leads from the city to the Gray farm and onward to the Bautsch and Boevers farms to the south of it."

Sep 1, 1946

This final report summarizes the effort on a very aggressively scheduled and demanding development program undertaken by Westinghouse for the U.S. Bureau of Mines under Contract No. H0101262. The objective of this program was to produce hardware and test it to determine the efficacy of certain concepts of Coal Mine Rescue and Survival as established by the request for proposal and the study performed for the U.S. Bureau of Mines by the National Academy of Engineering (NAE). (These are stated in paragraph 1. 1 for reference.) In carrying out this program, Westinghouse provided specific hardware designs in consonance with the objectives of the concepts outlined in the NAE study final report. Though this contract did not require producing final design hardware ready for introduction to the coal mining community, components of the CMR&SS - as delivered - have some value in disaster situations and are to be kept on standby alert. Additional design and production development is required and should be undertaken on most of the subsystems and components before they can be used in the competitive coal mining community.

Jan 1, 1971

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they arc required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by G. E . Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By B. K. Shibler

A highly flexible laboratory-scale fluidized-bed reactor was designed, constructed, and successfully operated continuously at temperatures up to 1,300° C during an investigation of thermal methods for decomposing gypsum. This report discusses briefly the many problems encountered in developing the 10-inch-diameter reactor and describes its design and construction in sufficient detail to enable other research organizations to build a comparable unit. The reactor consists of a 10-inch-inside-diameter vertical tube which can be varied from 6 to 10 feet high; it is formed from 2-and 3-foot sections of silicon carbide pipe. The tube is surrounded by a 3-inch heating space formed by an outer 4.5-inch-thick circular wall of insulating firebrick. A cone-shaped fluidizing chamber is bolted to the bottom of the reactor. Fluidizing gas enters through the bottom of the cone, and ore is introduced by means of a screw feeder connected to an inlet located just above the gas port. A silicon carbide overflow tube of 1.25-inch inside diameter extends upward into the reactor. The depth of the bed is controlled by substituting different lengths of overflow tube. Twin dust-recovery systems, each composed of a cyclone and Fiberglas filter, are attached to two gas outlets at the top of the reactor tube. The reactor is designed for research on both exothermic and highly endothermic reactions. It can be fired externally by means of four natural gas burners that jet tangentially into the annular space at the base of the reactor. Alternatively, it can be fired internally, using a mixture of air or oxygen and natural gas as the fluidizing medium. A separate instrument panel contains flowmeters, manometers, an automatic program controller, and a multiple-point recorder for printing a record of the temperatures measured by thermocouples located at critical points in the reactor.

Jan 1, 1963

By Arthur V. Petty

The Bureau of Mines has investigated the effect of refractory oxide additions, introduced in soluble form, on the refractory properties of 42-, 58-, and 70-pct-A1203 brick. Brick having porosities ranging from 12 to 16 pct were impregnated with solutions containing chrome, chrome-iron, zirconium, calcium, magnesium, cobalt, nickel, tin, and manganese ions. Additions of some of these ions provided dramatic improvements to such properties as hot modulus of rupture, hot load, and particularly slag resistance. These improvements can be related to reduction of porosity, amorphous grain boundary phases, formation of more refractory bond phases, and reduction of the wettability of Al203-containing refractories by metallurgical slags. Fifty-eight-percent-AI203 brick, impregnated with chrome, showed hot modulus of rupture, hot load, and slag resistance two to five times better than those of untreated 70-pct-AI203 brick. This could result in reducing the Nation's dependence on imported refractory-grade bauxite generally required for high-A1203 brick, as domestic alumina resouces could be used to produce the improved refractories.

Jan 1, 1984

By Scott W. Hazen

This report presents the results of a statistical analysis of a limited amount of sample and assay data from a production panel in an open - pit phosphate mine in the Phosphoria formation in Idaho . A frequency distribution analysis is shown for the assays , sample interval lengths , and products of assay and sample interval length for the millshale , furnace - shale , and main phosphate beds . Correlation techniques were used to show the relationships between assays and sample interval lengths . Within- drill - hole and between - drill - hole correlation were also examined as a means of predicting grade trends in the ore . Simulation methods , utilizing a digital computer , were used to establish assay populations that could be used for estimating grade of ore , cutoff grades , and deposit or bed identification .

Jan 1, 1964

BIBLIOGRAPHY Allen, C.A, Analyses of Utah Coals, United States Bureau of Mines Technical Paper 345, 1925, pp. 90. Allen, J.E. and E.M. Baldwin, Geology and Coal Resources of the Coos Bay Quadrangle, Oregon, Oregon Department of Geology and Mineral Industries Bulletin 27, 1944, pp. 160. "Aluminum Boom Raises Productivity", Coal Age, Vol. 82, No.6, June, 1977, pp. 103.

Jan 1, 1978

By Robert A. Speirer, Richard G. Burdick

Methods of detecting geologic faults and other linear features by means of processed LANDSAT satellite images have gained prominence during the past several years . There have been numerous programs written to pick these " lineaments , " but they have been almost universally tailored to large computers . This Bureau of Mines report describes a detection method developed for use with a minicomputer . The method comprises a suite of programs that scans an image for all " potential " lineaments . From this partially analyzed data , the final lineaments are picked by another routine . The method was field tested in an area of south- central Wyoming , and results indicated good agreement between computer- picked lineaments and ground features . Most of the known geologic faults in the area were picked by the method . Such features as roads and trails were also picked but were easily distinguished from faults during field inspection . The method is relatively new but promises to be a viable reconnaissance technique for the mining industry in geologic structural analysis .

Jan 1, 1965

By J. T. McCartney

The Bureau of Mines has developed an automated reflectance scanning microscope system, primarily for determination of volume proportions, size distribution, and mode of association of the physical (petrographic) components of coals. The process, which is potentially more rapid and objective and less tedious than a visual microscopic procedure, involves magnetic tape recording of several millions of reflectance readings on micro-meter sized areas of polished coal surface and computer analysis and interpretation of some characteristics of the coal components. The system was tested in a study of pyrite distribution in steam coals. The application was essentially successful, but defects in polished pyrite surface characteristics and problems in adequate sampling prevented completely satisfactory results. Pyrite con-tent and coal-pyrite particle association could be determined nearly as well as by visual microscopy, but size distribution data were less acceptable.

Jan 1, 1969

By W. P. Haynes, J. W. Mulvihill, G. B. Taylor, S. Katell

Capital and operating costs have been estimated for separating methane and hydrogen in gas - separating plants designed to produce 90 million scf per day of product gas containing a minimum of 90 percent methane . After a preliminary literature review of various separation techniques , three different processes --moving - bed adsorption using active carbon , oil absorption , and liquefaction -- were chosen for the cost estimates . Three different methane feed gas concentrations , 5 , 20 , and 50 percent ( cases 1 , 2 , and 3 , respectively ) , were chosen as representative methane concentrations for the separation estimates . Capital and operating costs were lowest for the moving - bed adsorption process in all three cases investigated . Operating costs declined from $ 0.24 to $ 0.06 per 1,000 cu ft of product gas , and capital costs declined from $47,490,800 to $7,411,200 as the percentage of methane in the feed gas increased from 5 to 50 percent .

Jan 1, 1964

By D. H. Platt

Gypsum and gypsite, used in the manufacture of plaster and plaster products, have been mined from deposits near Acme, Hardeman County, Tex., for more than 30 years. The Certain-toed Products Corp., 120 East Lancaster St., Ardmore, Pa., operates the Acme, Tex., mine. Underground hauling was done with storage-battery and Diesel-electric-powered shuttle cars. Many mining companies and individuals have manifested interest in all types of equipment powered by Diesel or Diesel-electric units, as attested by the recent increase in use of Diesel-powered equipment in underground metal and nonmetal mines. The purpose of this paper is to describe the manner in which a storage battery-powered Joy Model 60D2 shuttle car was converted to Diesel-electric power. The conversion was made, at the instance of the operating company, by Stewart & Stevens on Services, 4801 Lemon Ave., Dallas, Tex. This is believed to be the only such converted shuttle car in use.

Jan 1, 1950

By H. Kenworthy

The objective of this investigation was to evaluate the technical feasibility of smelting certain low-grade domestic iron ores in an electric furnace. Laboratory-scale experiments showed that a high recovery of iron in the form of pig iron can be obtained from east Texas ores containing less than 25 percent iron. The pig iron was amenable to standard-or electric-furnace-refining methods for producing steel. Car-bon, silicon, and phosphorus were the primary impurities removed in refining. Overall recoveries of iron as pig iron exceeded 95 percent, in contrast with commercial mineral-dressing recoveries on these particular ores of 50 percent of the iron as a 45-to 50-percent iron concentrate.

Jan 1, 1958

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1968