Search Documents

By R. V. Higgins

This report presents the results of a study of gas injection in the Upper and Lower Terminal zones in fault block VB and in the Upper Terminal zone in fault block VI, Wilmington field, California. This report is based on data obtained to January 1956. Earlier studies of gas injection in other California fields have been reported .3/ The Upper and Lower Terminal zones, fault block VB, have been producing oil since 1945 and the Upper Terminal zone, fault block VI, since 1948. Before starting the gas-injection project, the expansion of dissolved gas was the principal mechanism moving the oil to the wells. Gravity drainage and an edgewater drive also have contributed to the movement of the oil to the wells. When the gas injection was begun, the reservoir pressure and the oil production had declined appreciably. Gas injection was started in the Upper and Lower Terminal zones, fault block VB, in May 1953 and in the Upper Terminal zone, fault block VI, in October 1953.

Jan 1, 1957

By W. H. Forbes

The prevention of accidents from falls of roof and coal requires a considerable amount of personal judgment , for conditions are different even in adjoining working places in the same mine , and conditions may change from hour to hour even in the same working place as the coal is shot down and loaded . Experience has shown that many men can not or do not exercise enough care to protect themselves from injuries ; moreover , where the foremen have been made directly responsible for the safety of the men under them , accidents from falls of roof and coal have , in many instances , been reduced as much as 50 per cent . There is now no question that careful , constant , and intensive supervision is essential in preventing acci- { dents and more especially accidents of this class . Falls of roof and of coal account for approximately 50 per cent of all coal mine accidents and annually result in the death of approximately 1,000 men and cause lost - time injury to approximately 50,000 men . These and other accidents are recurring with little or no diminution , usually not because of the lack of knowledge of safe and dangerous practices , or of the technique of safety , but largely because of the lukewarm interest of major executives in safety or the failure of mine officials to formulate and to enforce common - sense rules and regulations . When failure is the outcome of a sincere attempt of the managing officials to teach safety to the miner , the fault may usually be attributed to misguided effort . Various solutions for the problem of eliminating accidents from falls of roof or coal have been suggested , some of which are : Standard system of timbering for the specified mining districts ; departure from the room-and - pillar system to a more concentrated system of mining ; more intensive supervision - that is , 1 section foreman for every 25 loaders instead of 1 section foreman for 75 , 80 , or even more loaders the practice in most mining districts . - However , investigations conducted by the writer at numerous mines operated by a number of mining companies in several districts show that employees and officials alike are inclined to work under loose and unsupported roof , relying solely on the " drummy " sound and on their judgment and experience as to whether the roof will stay in place for one hour or for several hours . With but few exceptions , men who had been injured by falls of roof or ccal or were found working under loose and unsupported roof , admitted that they knew of the possibly unsafe condition , but it was their opinion that the roof or coal was not loose enough to fall for some time .

May 1, 1931

By Jack I. Paige

The Bureau of Mines conducted studies to provide data on the room temperature mechanical properties of Ti-6Al-4V alloy cast in waterglass-bonded zircon sand and to determine the effect of hot iso-static pressing (HIP) on these properties. Data on the cast and annealed Ti-6Al-4V alloy were compared with published data for forged and investment-cast Ti-6Al-4V alloy. The average Charpy V-notch impact strength compared favorably with the typical values of 17 ft?lbf for wrought material and 19.2 ft?lbf for investment-cast material. The room temperature mechanical proper-ties of cast and annealed material compared favorably with published values for investment-cast Ti-6Al-4V alloy and exceeded the specifications for (1) titanium and titanium alloy castings, grade C-5 according to ASTM B367-69, and (2) titanium alloy bars and forgings as specified in AMS4928H, except for the AMS4928H minimum requirement for reduction in area (25 pct). The minimum requirements are: tensile strength, 130 ksi; yield strength, 120 ksi (0.2 pct); and elongation, 6 pct. None of the specimens tested met the AMS4928H minimum requirement for reduction in area. The HIP process healed the internal casting porosity in the test specimens, but the fatigue strength was not significantly improved. The fatigue properties of both the cast and cast plus hot isostatically pressed castings were significantly lower than those of wrought products.

Jan 1, 1984

By Jr. Herty

As the problem of inclusions in steel has become increasingly important, more and more attention has been paid to the source of the oxide inclusions in steel. In killed steels the oxide inclusions are traceable to the reaction of deoxidizers with the iron oxide dissolved in the steel during the refining period of the open-hearth heat. In a large class of steel known as "rimming steel" the action of the steel during solidification depends entirely on the gas evolved, and this evolution in turn is controlled by the amount of iron oxide in the liquid steel in the mold. It is therefore of great importance to be able to determine the amount of iron oxide dissolved in steel and to devise methods for the control of iron oxide in any class of steel. The object of the present investigation was to obtain a true value of the oxygen con-tent of liquid steel. If the steel has not been deoxidized, the greater percentage of the oxygen is present as iron oxide in solution.

Jan 1, 1932

By K. E. Stanfield

One of the initial projects under the oil-shale research and development phase of the Synthetic Liquid Fuels Act, Public- Law 290, 78th Congress, approved April 5, 1944, was a survey of oil shales of the United States for the selection of a site for an oil-shale demonstration plant. The oil shales were assayed by the conventional Bureau of Mines retort method proposed by Karrick and described by Guthrie in a more recent publication. From previous experience and that had in making these assays, it became evident that the assay method should be modified or replaced by a more satisfactory one. There are several outstanding objections to the Bureau of Mines oil-shale assay method: (1) the oil yields are frequently smaller than those obtained by other types of assay equipment and by commercial retorts; (2) the assayed oil yield represents only a portion of the organic matter in the shale, which under more favorable conditions, may, Jae converted, more completely into oil; (3) the retorting procedure is controlled mainly by trial-and-error methods; and (4) the assay requires approximately 6 hours for completion.

Jan 1, 1949

By J. E. Chilton

Underground miners may be exposed to hazardous quantities of toxic gases, such as carbon monoxide (CO), generated from mine fires or explosions. Every underground miner is required to carry a filter self-rescuer (FSR), which when operated will remove CO from the miner's breathing air. In addition, every underground miner must have a self-contained self-rescuer (SCSR) near the worksite that will supply breathing oxygen. In many situations, miners do not know when to don either rescuer since they do not know if there is a fire in the mine, nor do they carry instrumentation necessary for the detection of the toxic, colorless, and odorless fire product CO. If each miner carried a personal CO alarm, which would respond to high concentrations of CO, the miner would then be alerted when to don either the FSR or SCSR and exit the mine. A prototype personal miner's CO alarm called PEMCOAL was developed by the U.S. Bureau of Mines. The PEMCOAL unit is small enough to be carried on a miner's belt, has a flash lamp visual alarm, requires no calibration for use, and uses a chemical sensor that changes color by reaction with trace quantities of CO. The chemical sensor was tested at concentrations of CO from 10 to 1,000 ppm, at temperatures from 5° to 40° C, and with several potential mine gas interferents. The PEMCOAL alarm times were sufficiently fast to warn miners before they are exposed to hazardous quantities of CO.

Jan 1, 1989

By P. D. Kovscek

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted mechanical cutting system to determine the effect of the high-pressure sprays on machine performance, airborne dust levels generated, and size of particles formed. Testing was conducted on a simu-lated coal block (coalcrete) while cutting at a water pressure of 190 psi and at water-jet-assisted pressures ranging from 1,000 to 6,000 psi. The shearer motor energy used by the shearer while cutting coalcrete was determined for each cutting condition. Results indicate that the motor energy required by the shearer for each ton of material cut did not vary significantly as the water pressure was increased. Results of dust measurements recorded near the cutting drum indicate that at water pressures above 3,000 psi, dust reductions up to 85 pct were achieved com-pared with cutting with conventional sprays. Analysis of the particle size distribution during cutting showed that increasing the water pres-sure resulted in increased median particle size. In light of these results, various mechanisms for water-jet-assisted cutting are discussed.

Jan 1, 1986

By Jürgen F. Brune, R. Karl Zipf, Michael J. Sapko

Seals are barriers constructed in underground coal mines throughout the United States to isolate abandoned mining panels or groups of panels from the active workings. Historically, mining regulations required seals to withstand a 140-kPa (20-psig) explosion pressure. However, the Mine Improvement and New Emergency Response Act (“MINER Act”) requires the Mine Safety and Health Administration (MSHA) to increase this design standard by the end of 2007. This report provides a sound scientific and engineering justification to recommend a three-tiered explosion pressure design criterion for new seals in coal mines in response to the MINER Act. Much of the information contained in this report also applies to existing seals. Engineers from the National Institute for Occupational Safety and Health (NIOSH) examined seal design criteria and practices used in the United States, Europe, and Australia and then classified seals into their various applications. Next, the engineers considered various kinds of explosive atmospheres that can accumulate within sealed areas and used thermodynamic calculations and simple gas explosion models to estimate worst-case explosion pressures that could impact seals. Three design pressure-time curves were developed for the dynamic structural analysis of new seals under the conditions in which those seals may be used: unmonitored seals where there is a possibility of methane-air detonation or high-pressure nonreactive shock waves and their reflections behind the seal; unmonitored seals with little likelihood of detonation or high-pressure nonreactive shock waves and their reflections; and monitored seals where the amount of potentially explosive methane-air is strictly limited and controlled. Figure 1 is a simple flowchart that illustrates the key decisions in choosing between the monitored or unmonitored seal design approaches and the three design pressure-time curves. For the first condition, an unmonitored seal with an explosion run-up length of more than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections exists. The recommended design pressure-time curve rises to 4.4 MPa (640 psig) and then falls to the 800-kPa (120-psig) constant volume (CV) explosion overpressure. For unmonitored seals with an explosion run-up length of less than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections is less likely. A less severe design pressure-time curve that simply rises to the 800-kPa (120-psig) CV explosion overpressure may be employed. For monitored seals, engineers can use a 345-kPa (50-psig) design pressure-time curve if monitoring can ensure that (1) the maximum length of explosive mix behind a seal does not exceed 5 m (16 ft) and (2) the volume of explosive mix does not exceed 40% of the total sealed volume. Use of this 345-kPa (50-psig) design pressure-time curve requires monitoring and active management of the sealed area atmosphere. These design pressure-time curves apply to new seal design and construction.

Jan 7, 2007

By Carl Rampacek

Recent research by the Bureau of Mines has demonstrated that the segregation process has merit for treating oxidized and mixed oxide-sulfide copper ores. The process comprises heating the crushed ore with salt and coke or other carbonaceous materials at about 700° C. to produce fine flake copper, which then is recovered by conventional copper-flotation methods. Bench-scale laboratory tests of a number of oxidized and mixed copper ores assaying 0.78 to 5 percent Cu gave copper recoveries of 73 to 96 percent. The flotation concentrates assayed 21 to 76 percent Cu, depending on the ore being treated.

Jan 1, 1959

By Forrest T. Moyer, Nina L. Jones, Mary B. McNair, Virginia C. Berté

To keep the mineral and allied industries informed of trends in the causes of accidents, and to point out the need for corrective measures, the Bueau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1963 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings:

Aug 1, 1965

By J. V. Batty

In the course of the investigation of manganese mineral occurrences in the United States, Bureau of Mines examining engineers collected several lots of ore from the Black Rock, Kramer, and. Morgan-Cromar properties, Tooele and Juab Counties, Utah. Extensive laboratory tests were made to determine the amenability of the ores to standard ore-dressing methods of concentration. The Black Rock claims 1 and 2 are 42 miles northwest of Jericho, Tooele County, Utah. A. J. Huber of Salt Lake City and Ross Rydalch of Tooele, Utah, are the owners. The deposit-is reported to be a definite manganese fissure vein in quartzite along which considerable shearing and cross fracturing have occurred. Laboratory work was conducted on a 2-ton sample of run-of-mine ore procured by a Bureau of Mines examining engineer and two smaller, higher-grade samples submitted by the owners as a result of later development. The Kramer deposit is described as a bed of manganese oxides in quartz. The property is being worked by L. E. Kramer, Tooele, Utah, and is 41 miles northwest of Jericho) Tooele County, Utah, approximately 1 mile north of the Tooele-Juab County line. A 1-ton run-of-mine sample was submitted for testing by the examining engineer.

Jan 1, 1952

By Ernest W. Loya

The Bureau of Mines has developed a computer program for calculating the composition of gravimetric primary standard gas mixtures. The Fortran IV program applies corrections due to buoyancy variations of the cylinder and inaccuracies of the balance weights. The program also determines the statistical error due to the sensitivity and precision of the balance and applies the analytical error of the weighed gases.

Jan 1, 1985

Tax for Toxic Waste Cleanup. - The Superfund Act of 1980 became effective April 1, and provides that producers of certain metals and chemical substances are to be taxed in order to fund toxic waste cleanup. Industry will provide 88% of the 5-year, $1.6 billion fund. The Environmental Protection Agency will administer the Act, but the Internal Revenue Service will be responsible for collection of the industry tax. Under the Act, nickel companies, for example, will be required to pay a tax of 0.225 cents per pound on pure nickel products produced or imported into the United States. Standard for Exposure to Lead. - The Occupational Safety and Health Administration (OSPA) has announced a stricter standard on the test of a worker's exposure to lead. Effective May 15, in all lead intensive occupations with the exception of those at primary and secondary lead smelters, a worker would have to be removed from his work station if the level of lead in his blood tests out at 60 micrograms of lead per 100 grams of blood, instead of the previous standard of 70 micrograms. In the case of primary and secondary lead smelters, the ruling has been stayed until June 1, 1981, to allow time for further study.

Jan 1, 1981

By A. L. Engel

In recent investigations of chloride Volatilization of gold at the Reno Station, it was found that the addition of small amounts of copper and NaCl to the charge brought about improved volatilization of the gold. The investigations described in this report were concerned with the recovery, in an aqueous medium, of fumes from chloride volatilization of gold. It was attempted to discover a suitable aqueous medium that would permit absorption, solution, or precipitation of all the volatilized gold immediately upon contact with the medium. A simple laboratory apparatus was employed to produce fumes by volatilization. To this furnace was attached an absorption train consisting of a series of chambers containing the aqueous medium, through which the fumes were drawn by suction. A satisfactory synthetic ore that contained metallic, gold in a quartz-matrix was made and utilized, enough. gold being present in a' small amount of material to permit an accurate, metallurgical balance of the volatized values' to be obtained in all the experiments.

Jan 1, 1949

By K. C. Dean

Fine-sized mineral wastes discarded by ore milling plants require stabilization to prevent air and water pollution. Stabilization has been attained by physical, chemical, vegetative, and combination procedures. Vegetative reclamation is preferred to physical and chemical stabilization but is diffi¬cult to achieve because the wastes are sterile, contain deleterious inorganic salts, and lack the essential nutrients and physical characteristics required for sustaining vegetative growth. Methods now have been developed for attain¬ing vegetative growth on all but excessively acidic, basic, or saline tailings at costs ranging from $120 to $650 per acre. The cost for stabilizing tail¬ings requiring more intensive treatment techniques may range upward to $1,750 per acre. This report summarizes procedures developed by the Bureau of Mines and industry for vegetating amenable tailings, lists costs for the various processes, and suggests procedures that may be applicable for stabilizing saline and pyrite-containing tailings. Ridged planting beds, drip irrigation, and deep-furrow planting techniques are suggested for stabilizing saline wastes. A combination of mill tailings and sewage sludge can be used for pro¬ducing synthetic soils, and layers of sewage sludge buried under a layer of tailings offer promise of inhibiting acid formation from oxidation of sulfides in mineral wastes.

Jan 1, 1974

By John A. Kost

Control of the dust produced by continuous mining machines in coal mines is conventionally attained by water sprays from fixed nozzles mounted on the frame of the machine behind the cutting head. In the tests conducted under this contract a so-called "wet-head" machine was used, where the spray nozzles were mounted on the rotating head itself, close to the coal-cutting bits. The tests were conducted at the Robena Mine of U.S. Steel Corporation, using Lee-Norse machines. Operating the wet-head machine and a conventional spray machine in turns in the same section, it was found that the wet-head produced approximately 25 percent less respirable dust and 60 percent less total airborne dust than the conventional spray machine. The wet-head also greatly improved the visibility of the cutting bits from the machine operator's position. Several difficulties had to be overcome before any meaningful tests could be conducted, including excessive pressure drops in the piping system and plugging of the nozzles from internal water contamination. The major obstacle, however, was the rotating water seals on the wet-head, which leaked excessively after only a few hours of operation. Only after several changes and plant and laboratory tests was a design found which permitted conducting the underground tests without appreciable water leakage.

Jan 1, 1976

By E. C. Strycula

Solid-state equipment offers a number of potential advantages in the coal mining industry. These advantages can only be realized, however, through careful and judicious design of the control and protection circuitry. Problems relating to the interaction of solid-state equipment on the electrical system and the special design considerations which apply to solid-state circuitry are examined. Design guidelines are provided for solid-state applications in the areas of: (a) equipment operated from a DC trolley wire, (b) drive systems for surface mining equipment, (c) AC motor starters, and (d) electromagnetic interference.

Jan 1, 1981

By Alan D. Hartman

Standard metering of electric arc furnaces usually uses root mean square (RMS) or true root mean square (TRMS) measurements for determining power. Only sinusoidal signals are accurately described by RMS meters, and dc or high-frequency components normally are lost in standard TRMS metering. This can lead to inaccuracies when electrical signals are not sinusoidal, contain dc components, or include fast risetime perturbations, as is the case with the electric signals from an electric arc furnace. Electric arc furnace electrical waveforms, observed in research carried out by the U.S. Bureau of Mines, show high-frequency components and significant deviations from sinusoids. These perturbations and distortions make metering difficult for standard power meters. The inaccuracies in metering can cause further problems if those sensors are used in control systems. For control strategies requiring rapid response, any averaging scheme loses information that can be used in control decisions. In order to obtain better signals for both monitoring and control, a study of instantaneous, RMS, and TRMS power monitoring devices was conducted. From this study it was concluded that precision integrated circuits should be used to obtain instantaneous power with a bandwidth of at least 25 kHz. The information from these devices is more representative than that of standard meters and can be used in predictive control.

Jan 1, 2010

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a minicomputer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns An echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display dis[c]s, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 1, 1980

By Fay B. Dillard

This Bureau of Mines report reviews the disposition of natural gas as delivered to industrial consumers via main line sales. Salient information on main line, or direct, natural gas sales to industrial users is presented by State) standard industrial classification code (SIC) revenue, and type of sales for the years 1968 through 1973.

Jan 1, 1975