Search Documents

By S. J. Schatzel, W. P. Diamond

Longwall mining alters the fluid-flow-related reservoir properties of the rocks overlying and underlying an extracted panel due to fracturing and relaxation of the strata. These mining-related disturbances create new pressure depletion zones and new flow paths for gas migration and may cause unexpected or uncontrolled migration of gas into the underground workplace. One common technique to control methane emissions in longwall mines is to drill vertical gob gas vent holes into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important to optimize the well parameters, e.g., the borehole diameter, and the length and position of the slotted casing interval relative to the fractured gas-bearing zones. This paper presents the development and results of a comprehensive, "dynamic," three-dimensional reservoir model of a typical multipanel Pittsburgh coalbed longwall mine. The alteration of permeability fields in and above the panels as a result of the mining- induced disturbances has been estimated from mechanical modeling of the overlying rock mass. Model calibration was performed through history matching the gas production from gob gas ventholes in the study area. Results presented in this paper include a simulation of gas flow patterns from the gas-bearing zones in the overlying strata to the mine environment, as well as the influence of completion practices on optimizing gas production from gob gas ventholes.

By Lloyd G. Fitzgerald

"The dangerous nature of explosives makes them a potential hazard wherever they are used, but they are likely to exercise their greatest harmfulness under conditions inherent in coal mining. The ease with which explosives can be detonated and the suddenness and violence with which they detonate require great care in their handling and use, if acci-dents are to be avoided. Campaigns have been waged by the manufacturers, the Federal Bureau of Mines, coal-mining companies, and other agencies to educate users of explosives in their dangers and in their proper use and care.Probably 95 percent of the explosives accidents can be attributed to poor judgment, carelessness, negligence, or chance taking. In many explosives accidents it is difficult to determine the cause definitely, as the evidence of the origin is destroyed by the blast and frequently those involved have been killed. Survivors of the accident often are of little help in determining the cause, as the accident occurs so suddenly they cannot tell what happened or prefer not to divulge the information they have because it may point to their own carelessness.A survey has indicated that about 10 percent of all fatalities in coal mines were caused by explosives accidents (excluding gas and dust explosions initiated by explosives). A list of explosives accidents by States, from 1925 to 1932, classified according to the severity of the accidents, indicated that Kentucky and Wyoming had the greatest number of fatalities resulting from explosives accidents. Records of the Bureau of Mines show that 14 coal-mine explosions occurred from January 1 to June 1, 1943. Explosives were involved in four of these explosions. Black powder caused two of the accidents and permissible explosives used in a nonpermissible manner the other two. These statistics are mentioned to show that explosives are still causing severe accidents.Elimination of the hazards associated with explosives begins on the surface. Storage magazines should have no opening, except for entrance and ventilation; ventilators should be screened effectively to prevent the admittance of sparks as well as to prevent unauthorized entrance. The interior should be kept clean and dry, and the floor should be of nonsparking material with no metal exposed. The surrounding area should be kept free of combustible material for not less than 25 feet (and preferably 50 feet) in all directions. Storage magazines should be fire-resistant and reasonably bulletproof."

Aug 1, 1944

By Walter C. Lorenz

In connection with its renewed study seeking solutions to problems created by release of acid water from bituminous coal mines, the Bureau of Mines recently surveyed reports already written on the subject. This publication is based on that search. The Problem Poor distribution of water is evident on an ordinary geographic map of the United States. The more abundant supplies of surface water appear to be centered in the northeast, the southeast, and the central humid areas of the country. It is in the midst of this abundant surface water, in the Ohio River Valley, that most of the bituminous coal is mined. Varied industry has located in the valley to use the coal and the river. The coal is a source of power and o raw material. The river provides transportation for raw and finished materials; equally important, it provides the water that is used for cooling and processing in manufacturing. It also serves as a vehicle for the disposal of waste.

Jan 1, 1962

By R. A. Franks, G. F. Friel, J. C. Edwards, A. C. Smith

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system's ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system's ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system.

By G. L. Oldwright, Virgil Miller

"The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada Limited, Trail (Tadanac), Brithish Columbia. The authors are greatly indicated to S.G. Blayrock, vice president and general manager; James Buchman, smelter superintendent; and the staff members mentioned in Report of Investigation 3243. The authors are exceedingly grateful to George Murray, assistant smelter superintendent, for his keen interest, suggestions, and help in carrying out this investigation.INTRODUCTIONThe methods of charign the blast furnaces at Toole and Kelloggs were noted in Report of Investigations 2957 and 3094 respectively. Report of Investigations 2957 cited (4 to 9 inclusive) Hofman's Metallurgy of Lead (p. 226) and the work of A.S. Dwight, Thompson and Sicka, the staff of the Engineering and Mining Journal, and L.D. Anderson, N.F. Collins, in The Metallurgy of Lead (Chas. Griffin, London, 1910) also gives (pp. 247 254) the principles that he believes govern the successful charging of the blast furnace."

Dec 1, 1934

By C. Richard Groves

As the level of technology applied in the electrical measurement, control, and display portions of mine hoist systems continues to advance, the issues and concerns associated with the ramifications of the application of microprocessor technology on the safety-related aspects of these systems become paramount. This report, in part tutorial, addresses several aspects of these concerns. Beginning with discussions of microprocessor-based system architectures, the report addresses some existing and anticipated uses of this technology in mine hoist systems and discusses safety related considerations associated with the areas of data derivation; control and display panels; and system reliability issues. The report concludes with electrical maintenance and inspection considerations associated with the safety assurance of microprocessor based mine hoist systems.

Jan 1, 1986

A prototype EM Location System was fabricated and tested at the Geneva Mine near Dragerton, Utah. This system consisted of six manpack transmitters and six manpack receivers covering the frequency band from 900 Hz to 2900 Hz as well as a six channel receiver designed for use, in a helicopter. Tests showed that EM signals from lightweight (3/4 lb) transmitters could be detected both on the surface and from a helicopter through as much as 4450 ft of relatively high conductivity (2 X 10- 2 mhos/m) overburden. Furthermore, the resulting field strength profiles could be used to determine source location to within 150 ft of the actual surveyed location in the mine. Modifications were made to a Monitoring, Locating and Communications System being tested at the Bruceton Mine, Pittsburgh, Pennsylvania. These modifications have improved the performance and quality of the paging and voice telephony mode of the system. Subsurface receiver modifications have improved reception of voice downlink signals.

Jan 1, 1973

By J. D. Clendenin

Systematic practices for protecting crops from frost damage began in the United Metes more then 40 years ago when the Weather Bureau Fruit-Frost Warning Service was organized; however, various practices employed in frost protection are centuries old. Although there are areas where little doubt exists as to whether protection is needed, there are also circumstances where there is some doubt as to the need for frost protection. Many factors influence this, including not only critical temperatures but also the maturity dates of the crops relative to marketing. Critical temperatures for frost damage to trees, plants, blossoms, and fruits very with weather, plant variety and nutrition, and stage of growth. In the case of truck crops, a single night of protection from frost injury might yield big dividends with a variety of sweet corn or tomato that matures early while price is high yet be worth very little with a midseason or late-maturing variety. Consequently, it is the individual grower who must decide whether to use frost-protective measures on the basis of his returns, the quantity and quality of his crop, the marketing situation, the sensitivity of his crops to frost damage, and the frequency of damaging frost in his area.

Jan 1, 1955

By PALMER LARSEN

INDEX TO GEOPHYSICAL ABSTRACTS

May 1, 1931

By Alan Mayton, N. Kumar Kittusamy, Christopher Jobes, Farid Amirouche

Industrial equipment exposes individuals to whole-body vibration (WBV) and mechanical shock. This exposure can negatively impact their health, safety, comfort, and working efficiency and performance. Accordingly, proper seat design is an important consideration in reducing the adverse effects of WBV exposure to vehicle operators. Since the human body is sensitive to low frequency WBV, ride quality is a basic and important element of good seat design. When designing a suitable seat, it is essential to understand vibration exposure environment of workers and how well they can tolerate this environment [1]. This is particularly true in the mining industry. Mayton et al. [2] reported on a low-coal shuttle car seat design that underwent limited, yet successful underground mine trials. Building on this work, a follow-up study compared NIOSH and existing seat designs on low- and mid-coal seam shuttle cars. The NIOSH seat designs included viscoelastic foam, which has properties similar to those found in a mechanical spring/damper suspension system. The seats also included an adjustable lumbar support and a fore-aft seat adjustment. The NIOSH seat designs contrast with the existing seat design, which have little or no lumbar support and include inexpensive foam padding of the type commonly used in furniture. This paper will focus on the seat designs for the mid-coal seam shuttle car and compare subjective comfort data collected from five vehicle operators with ISO 2631 – based reduced comfort boundary (RCB) analysis of recorded vibration levels. Methods Experimental data were collected using three different tools: triaxial accelerometers, pre-amplifiers, and filters connected to a data recorder; a visual analog scale (VAS); and a short questionnaire. Researchers recorded quantitative or objective vehicle vibration data to determine the input and output acceleration at the operator cab floor and operator seat interface. Qualitative or subjective data, collected with the VAS, allowed researchers to obtain the operators’ immediate impressions of shock, vibration, and discomfort levels for the vehicle ride on each of the seat designs. Each shuttle car operator made six round trips with the vehicle each seat. The shuttle car operator marked the VAS on the first, third, and sixth round trip of the trials for each seat. A round trip consisted of traveling to the coal face with no load and returning to the load discharge location with a full load of coal. Results Total overall average ratings for the five vehicle operators of the mid-coal seam shuttle car, showed that operators sensed from 45 to 87% less discomfort with NIOSH seat designs compared to the existing seat design. Using a 95% CI, researchers computed a strong positive correlation for discomfort. Figure 1 illustrates the RCB analysis method for one of two NIOSH seat designs.

Jan 6, 2006

By R. J. Evans

The generation and disposal of solid waste from electric utility plants using a lime or limestone wet-scrubbing system and the potential effects on the environment were estimated for 1975 and 1980. The study indicated that in 1975 approximately 5.8 million tons of desulfurization solid waste (50 percent solids) will be generated. In 1980, when it is estimated that desulfurization will become commercially accepted, approximately 71.4 million tons of this material will be generated for disposal and/or utilization. The desulfurization waste material when combined with lime, fly ash, and water may have potential for use as a roadbase material, landfill reclamation, and synthetic aggregate.

Jan 1, 1974

By Scott W. Hazen

COMPREHENSIVE summary is presented of results of several years of research at the Bureau of Mines Mining Research Center at Denver on adapting and applying techniques of statistical analysis in mine and mineral-deposit sampling and in computing grade and tonnage of ore for a mineral deposit. In addition to elementary statistical theory the material presented in the bulletin includes: (1) Certain special statistical techniques that have been found useful in mining applications; (2) problems, implications, and limitations that may be encountered in applying these techniques in mine sampling and evaluation; and (3) numerous examples to demonstrate application of the theory and techniques.

Jan 1, 1967

By Walter W. Kaufman

The braking performance of underground, rubber-tired, non-coal mining vehicles is evaluated. Surveys of mining equipment and braking manufacturers and underground stopping tests are discussed as they relate to this evaluation. Stopping performance recommendations are included as well as related aspects of roadway construction and runaway vehicle protective devices.

Jan 1, 1977

By John S. Hutchins

Two potential modified in situ methods are described for recovering the 68% "unrecoverable" hydrocarbons in oil reservoirs. For the 300 billion barrels of conventional light crude a Drip Drainage system is suggested by mining underneath a reservoir and producing from below by controlled gravity flow. For the 200 billion barrels of heavy or viscous oil and tar sands deposits a Flip Flop process is described using surface flooding with hot water saturated with surfactant and weighting additives. Mining engineering description of shafts and tunnels required are included as is discussion of the tunnel proximity to a reservoir. Petroleum engineering flow equations to describe production rates and candidate reserve areas of the U.S. are described. DCF economics are provided to indicate that current oil prices may be sufficient to commercially develop these recovery methods.

Jan 1, 1978

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

By Bill York-Feirn

The Colorado Mine Safety & Training Program (MSTP), in late 2005, completed and began distributing two new training tools; one geared to underground coal mine foremen and the other to surface aggregate employees. Through strong partnerships with MSHA, Colorado Coal Mine Board of Examiners, Colorado Mining Association and the Colorado Rock Products Association, the MSTP continues to create innovative and interactive training tools for not only Colorado, but for the national mining community. "Although we shoot and produce these materials in Colorado, it's important to us to make sure they are useful nationally," said Bill York-Feirn, MS TP Manager. The interactive DVD program "Underground Mine Foreman Certification Study Guide (Coal)," was completed in October 2005. It won the 2005 Grand Prize at the MSHA National Training Materials Competition in Beaver, West Virginia. [ ] This program is fully based upon the requirements of Title 30 Code of Federal Regulations (30 CFR) Parts 48, 50, 70 and 75 for underground coal mine foremen. It contains eight modules plus immediate access to relevant laws in the appendix. Topics covered include: Federal Law, Practical Math Skills, Mine Gases, Ventilation Maps, and scenarios addressing a variety of practical mining concerns. The DVD is designed for self-¬paced study and practice.

Jan 1, 2006

By R. E. Kennedy

"INTRODUCTION In a previous publication4 results were given of numerous experiments made on the in-flammability of gas mixtures consisting of methane, hydro a. carbon monoxide, nitrogen, and carbon dioxide. Data were obtained and tables prepared giving the inflammable limits of each of these combustibles when mixed with various proportions of carbon dioxide and nitrogen. By the use of these data and the application of Le Chatelier's law, it was found possible to calculate the limits of inflammability of any gas mixture containing any or all of the above gases.Various mixtures of the five gases given above were prepared and their limits determined experimentally and then calculated. Good agreement was found between the determined and calculated results when complex gases encountered in mine safety work were tested. Of special significance was the accurate calculation of the limits of inflammability of gases from mine fires, gases from mine explosions, detonation products of explosives, blast—furnace gases, automobile exhaust gas, and other gases of a similar character.Using the method given in the above report, Yeaw5 investigated a number of industrial gases including oven, coal, producer, blue, carbureted blue, and dry quencher gases, and found the determined and calculated results to agree remarkably well, thus giving further proof of the value of such a means of determining dangerous conditions when combustible gases are encountered in practice.GASES FROM A POTASH MINEGases were recently encountered in a potash nine in New Mexico, containing the com-bustibles, methane, hydrogen, and ethane. In one special case a mild explosion occurred when these gases were mixed with the right proportions of air and ignited it therefore became necessary to know the inflammability of these mixtures in order that the proper precautions could be taken to prevent explosions."

May 1, 1932

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP),Version 1.0, was released at the 19th Ground Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (1) including uncontrolled convergence into the design requirements for standing roof supports, (2) the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capability to define ground reaction curves through convergence measurements alone without having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (1) additional graphics capabilities to facilitate rapid assessment of support comparisons, (2)an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and a measure of roof coverage for the design layout of the support system. These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions which could not be fully analyzed in the original version of the program.

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

By H. P. Greenwald, Irving Hartman, H. C. Howarth

"INTRODUCTION A report of tests of seven small pillars formed from the Pittsburgh coal bed in the Experimental coal mine was given in Technical Paper 605 5/ Five additional pillars were tested between July 1939 and. October 1940. The data obtained, in the later tests permit an extension of the conclusions reached in Technical Paper 605, which appears to be important enough to the mining industry to justify a progress report that will explain briefly what it is and how it was obtained. Full detail of the tests will appear in a second technical paper, preparation of which is deferred so that results of pillar tests now under way my be included.DESCRIPTION OF TESTSExcept for minor improvements in operating details, the five additional tests were made as described in Technical Paper 605, pages 2 to 7. Briefly, the desired pillar was formed from the coal bed, by excavating a passage around it (no explosives were used), and enough material was removed from above to permit installation of the assembly used for applying pressure. Each pillar was tested resting on its original fireclay floor, which was restrained from lateral flow by a ring of concrete. Vertical and lateral movement of the pillars in two directions as measured carefully in all tests."

Jun 1, 1941