Search Documents

By Michael Sokaski

A dense-medium cyclone pilot plant was built to clean 112-inch to 0 size coal. This pilot plant does not require the removal of the extremely fine material (usually minus 1/2-mm) from the feed, which is necessary in conventional dense-medium cyclone plants. The essential difference between conventional cyclone plants and the pilot plant is in the medium-recovery system. The latter uses a combination of sieve bend screens, classifying cones, and magnetic separators for medium recovery. Eight tests were run in the pilot plant at a feed rate of 5 tons per hour with four different raw coals and one crushed jig middling product. Sharp separations were obtained as indicated by an average error area of 27 and probable error of 0.047 for the 112-inch to 200-mesh size range. Magnetite loss averaged about 2.5 pounds per ton of feed. The influence of several factors on cleaning performance of the cyclone was investigated. The diameters of both the overflow and underflow orifices were found to be important for optimum cleaning performance, but these diameters could vary over a wide range without serious effect; however, if this range was exceeded, cleaning performance deteriorated. Better cleaning performance was obtained when the cyclone inlet pressure was increased from 9 psig to 13 psig. The size of the magnetite particles in the medium was found to have a substantial effect, and the best cleaning results were obtained with grade B magnetite. Demagnetizing the magnetite in an effort to decrease the effective particle size did not improve cyclone performance.

Jan 1, 1963

By W. E. Wells

This report describes experimental investigations made in the batchwise retorting of Colorado oil shale. Three heat-carrying mediums were used -hot shale gas, superheated steam, and hot flue gas. Using hot Shale gas for retorting, the several variables studied were retort-inlet-gas temperature, gas velocity through the shale bed, shale particle size, and grade of shale. In studying the effect of any one of these variables on oil yield, as and operability, the other variables were maintained essentially constant. Oil yields decreased with increasing in-let-gas temperature and increasing shale-particle size, and oil yield increased with increasing grade of Shale up to 50 gallons of oil per ton of shale, beyond which the process was inoperable because of swelling and caking of the shale during retorting. Changes in gas velocity had little effect on oil yield. Gas yield increased with increasing inlet-gas temperature, gas velocity, particle size, and shale grade. Oil yields of 100 percent of Fischer assay and from 1,600 to 1,800 cubic feet of 300-B.t.u. gas per ton of shale were obtained. Two runs only were made using superheated steam. Oil yields averaged 97 percent of Fischer assay, and gas yields averaged 4,00o cubic feet per ton of shale. Retorting with a hot flue gas produced from combustion in the shale bed, as in the N-T-U process, gave excellent yields using closely sized shale with recycling of flue gas. An excess of fine shale in the charge resulted in channeling and low oil yields. Using no recycle gas, good yields were obtained that tended to decrease with increasing air rate, and the retorting rate increased with increasing air rate over the range studied. Coking was not found serious with 30-gallon shale at the air rates used.

Jan 1, 1952

By R. E. Peterson

Scrap iron is partially oxidized at elevated temperatures in the selective oxidation process to produce iron oxide and a dense residual metal of high purity. Investigation of the process was confined to converting automobile hulks into useful products. In one test series, compressed, sheared automobile scrap was processed at 1,000° C in a 36-foot-long rotary kiln at feed rates ranging from 300 to 1,200 lb/hr. Less fuel was required to maintain the temperature at the higher feed rates because of the heat generated from the burning of the combustibles and the oxidation of the iron. The bulk density of the residual metal exceeded 75 pounds per cubic foot. In an attempt to lower the quantity of contaminants in the residual metal, another test was designed using automobile hulks which had been prepared by ripping, a low-cost method of scrap fragmentation. Before oxidizing the ripped scrap approximately 62 percent of the total copper was removed in a tumbling, screening, magnetic separation and hand-sorting system. Cast iron made from the residual metal obtained by selective oxidation contained 0.15 percent copper; iron oxide scale obtained from the kiln averaged 0.13 percent copper. Pellets made from the scale demonstrated compressive strengths necessary for blast furnace reduction; lead and zinc were removed by volatilization when the induration was performed in a reducing atmosphere.

Jan 1, 1972

By Young W. A.

The Eagle Silver mine is in the Rush Valley mining district, Tooele County, Utah, and is now operated by the Hampton Mining Co. The property, originally referred to as the Argent, is reported to have been one of the first discoveries in the district. The early operators mined ore to a depth of 850 feet, at which point the property was abandoned because of excessive water. During 1905 the Honerine tunnel was driven into the area approximately 1,800 feet below the collar of the Argent shaft. This tunnel served to drain the levels above and operations were resumed. Ore deposits in the Eagle Silver mine occur in the Galena King lime-stone, a 20-to 60-foot member of interbedded quartzite and limestone in the Oquirrh formation of Pennsylvanian age. This member has been faulted along the bedding, forming the Galena King gouge. Mineralization commonly occurs in or near this gouge area in a brecciated, highly altered, pipelike zone. The known ore shoots occur in association with the breccia pipe, commonly adjacent to cross faulting and porphyry intrusions. In general, two ore shoots have been mined on the upper levels of the mine, one lying to the east and the other to the west of the breccia zone. The Bureau of Mines diamond-drilling program was begun during the latter part of 1948 and completed early in 1949. Nine holes were drilled, aggregating 852.8 feet. Sludge and core samples from mineralized sections were analyzed in the Salt Lake City laboratories. A total of 87 sludge, 71 core, and 11 chip samples was submitted for analysis.

Jan 1, 1950

By William L. Crentz

Floyd County, KY., contains sizable deposits of high volatile bituminous coal. Some of the coals have been blended with higher-rank coals and used in the manufacture of high-quality metallurgical coke. The Upper Elkhorn No. 3, Upper Elkhorn No. 2, and Upper Elkhorn No. 1 beds produce the bulk of the present output in the county and contain the main known reserves of coal. Little information is available concerning the quality and extent of the deposits underlying the Upper Elkhorn No. 1 bed, although small operations in the past have worked a bed that is reported to be; the Lower Elkhorn. Undoubtedly, these lower beds occur in Floyd County, but depth Will preclude their development into a major source of fuel as long as large deposits of more-accessible coal are available. More is known of the occurrence of the beds above the Upper Elkhorn No. 3 owing to sporadic mining ventures in the upper measures. Many of the coal samples from beds above the Upper Elkhown No. 3. were collected in mines that had been abandoned. Almost all of the present production of Floyd County coal is taken from the Upper Elkhorn beds, and it is unlikely that their dominant position as coal producers will be challenged in the near future. Table 1 shows the coal production of the county by beds, during 1950.

Jan 1, 1952

Construction workers may be exposed to hazardous dust containing crystalline silica during site preparation when drilling systems are used. The National Institute for Occupational Safety and Health (NIOSH) found that drill dust could be decreased by using wet or dry dust reduction engineering controls, enclosed cabs, and implementing a dust control program.

Jan 1, 2009

By G. L. Neumann

The Andover-Sulphur Hill iron mines in Sussex County, N. J., have a production record extending over 100 years. The last production recorded was about 1880. These mines produced high-grade ore of two types: Bed ore (hematite) and blue ore (magnetite. Some sulfides (lead, zinc, and copper) were found underlying the iron deposits. Data as to size and grade of these sulfide bodies are very sketchy, Toward. J. Hewitt of Elizabeth, N. J., lessee of the Sulphur Hill mines from 194045, prospected for lead, zinc, and copper. .His Only production was several hundred tons of low-grade iron ore, which was crushed and used as heavy aggregate to make concrete blocks for ship ballast. In October and November 1942 made a magnetic survey of this area and bored six-diamond-drill holes with the dual objective of prospecting for sulfides and testing for extensions of the iron-ore deposits indicated by the magnetic survey. In 1944, an iron-mining company examined this property and diamond-drilled seven holes Between December 1949 and March 1950, the Bureau Of Mines in search of sulfide deposits, bored three additional diamond-drill holes. Two of these were on the Sulphur Hill tract and one on the adjoining Tar Hill tract.

Jan 1, 1952

By Y. Miron

Previous studies at the Bureau of Mines outlined the hazards of ammonium nitrate-fuel oil (AN-FO) mixtures in the presence of pyrite-bearing ores. The recent trend in the mining industry to strengthen AN-FO by the addition of aluminum metal raised the question regarding the effect of aluminum in AN-FO in the presence of pyrite-bearing ore. Laboratory work, similar to that done previously, demonstrated that the temperature of a self-sustaining reaction in the presence of AN-FO ore-aluminum is not lower than that for a comparable AN-FO-ore mixture. However, as might be expected from known thermochemical data, once initiated, the resulting reactions between AN-FO, aluminum, and pyrite are much more vigorous than those observed for AN-FO and pyrites alone. The temperature required to produce a self-sustained reaction for the combinations tested in this study is 250°±20° F while in the previous Bureau study, reactions were noted, in some instances, at 150° F. The different pyritic ores may be the cause of this variation.

Jan 1, 1976

By R. J. Fantel

The Bureau of Mines investigated the resource availability of titanium minerals from 63 mines and deposits in 12 market economy countries. These mines and deposits contain, at the demonstrated resource level, an estimated 438 million metric tons (mt) of titanium dioxide (TiO2) in the minerals rutile, ilmenite, leucoxene, and anatase. An additional 314 million mt of TiOz is available from inferred resources. If all titanium minerals and other recovered heavy minerals are sold at total costs at least equal to the January 1984 market prices, approximately 200 million mt of contained TiO2 could be recovered in total. In terms of mineral concentrates, this equals approximately 11 million mt of rutile concentrate, 187 million mt of ilmenite concentrate, 3 million mt of leucoxene concentrate, 13 million mt of synthetic rutile concentrate (in addition to the ilmenite), and 89 million mt of titanium slag. The study indicates that world resources of low-cost rutile are declining. In order to maintain future supply for high-grade titanium resources, alternate sources will need to be developed, which may include higher cost rutile mines, Brazilian anatase deposits, increased production from slag operations, or more synthetic rutile capacity from ilmenite resources, which are abundant.

Jan 1, 1986

By Gerald W. Elger

A new process under development by the U.S. Bureau of Mines for producing synthetic rutile from ilmenite is described. Rutile formation is based on oxidation and fluxing of titania slag produced by electric furnacing of ilmenite. Laboratory tests show that phosphorus pentoxide flux additions to oxidized slag enhance conversion to rutile by forming a phosphate-based glass matrix. This matrix contains most of the major impurities, including the oxides of iron, aluminum, magnesium, manganese, and silicon. Rutile crystals of 5 to 150 microns in size were formed in slags heated to temperatures of 800° to 1,550° C. The synthetic rutile crystals were liberated from ground slag by treating with phosphoric acid to weaken the glass matrix, followed by attrition scrubbing. Rutile fractions analyzed as high as 94 percent titania content. In several instances, more than 90 percent of the titanium in the shag was recovered to yield combined rutile fractions containing 90.2 to 92.6 percent titania.

Jan 1, 1971

By Shirley F. Colby

Much interest has been shown recently in the possible utilization of dolomite as a source of magnesium metal, a large production of which is deemed essential for national defense. As a result, many inquiries have been received by the Bureau of Mines as to sources of dolomite. This report has been prepared primarily to augment the Bureau's present published information on the occurrence of high-grade dolomite deposits in the United States. To supplement such data, the report also defines dolomite and related rocks and describes their properties and uses. The uses are covered in some detail in Information Circular 6524 entitled "Utilization of Dolomite and High-Magnesium Limestone," published in 1931 but now out of print. All essential data on uses contained in that report have been incorporated herein, and. have: been supplemented by data developed during subsequent years. DEFINITION Dolomite is a mineral composed of calcium end magnesium carbonates combined in equal molecular proportions, expressed by the formula CaMg(C03)2. Dolomitic limestones contain considerable dolomite but also include either

Jan 1, 1941

By B. W. Madsen

The Bureau of Mines conducted a large-scale (6.4 t), long-term (2,165 days) test to gain a better understanding of the leaching characteristics of chalcopyritic ores. An ore sample containing 0.77 pct Cu was leached in a fiberglass column by downward percolation of acidified ferric sulfate solutions. Three sets of leaching conditions were investigated: (1) ambient temperature leaching, (2) elevated temperature (50° to 60° C) leaching, and (3) elevated temperature leaching after inoculation with thermophilic bacteria. Leaching at ambient temperature resulted in a copper extraction rate of 0.44 pct per 100 days. Increasing the temperature to 50° to 60° C resulted in decreased activity of natural mesophilic bacteria, and the leaching rate decreased to 0.22 pct per 100 days. The pH was lowered from 2.0 to 1.6, and nutrient solutions that contained thermophilic bacteria were added. This procedure resulted in an increase in the ferric-to-ferrous iron ratio and an increase in the copper leaching rate. However, the increased leaching rate was not sustained, and 120 days after inoculation the bacterial activity declined, the ferrous iron content increased, and the copper leaching rate decreased.

Jan 1, 1983

By H. S. Auvil, J. T. McCartney, J. D. Davis

"INTRODUCTION It is now generally recognized that the small-scale laboratory dilatometer method of test does not give results of much utility in predicting the expansion (or contraction) of a coal in a coke oven. The carbonizing conditions in the laboratory test differ radically from those in the oven; in this test, the charge is heated through the coking range of temperature as a whole, whereas in the oven, coking proceeds by layers parallel to the oven walls as each succeeding portion of the charge goes through the plastic range of temperature and coke formation sets in. The paths of the gases and vapors and the pressures set up are different in the two methods. Furthermore, the rate of heating in the test usually is much more rapid than in the oven. H. Koppers 5/ was perhaps the first to adopt apparatus and procedure whereby the layer coking of the coke oven could be simulated closely however, the heating progressed from one side of the charge only; later he experimented with a small coke oven with a movable wall heated from both sides. It is not clear how well the results in the later oven correlated with those of the earlier small test oven, but in a comparatively recent Koppers publication a modification of the original small test oven heated from one side is recommended 6/ Altieri 7/ was perhaps the first to experiment with the Koppers type small test oven in the United States and Brown- has tested a large variety of coals in a rectangular test oven of his own design heated from the sole or floor. Subcommittee XV of American Society for Testing Materials Committee D-5 is now making a study of the various methods proposed for determination of expanding and plastic properties of coal with a view to standardization. 9/"

May 1, 1939

By Glen C. Ware

The Bureau of Mines determined the factors involved in the corrosion of starting sheets used in the production of electrolytic zinc with the ultimate purpose of adapting zinc starting sheets to commercial practice . Under present practice , zinc is electrodeposited on aluminum cathodes and subsequently stripped for melting . The use of zinc instead of aluminum would eliminate the need to strip the deposit , thereby reducing the cost of handling and melting it , but zinc has not been suitable because it was too vulnerable to the corrosive attack of the electrolyte . Serious attack was found to be limited to the areas of the cathodes situated immediately above the surface of the electrolyte and to re - entrant corners . It was possible to avoid solution - level corrosion by immersing the starting sheets completely , exposing only a relatively heavy suspension member to solution - level attack . Zinc starting sheets could be made as reliable as aluminum and could be continued in residence for periods up to 39 days . Periods as long as a week were feasible under conditions similar to those found in commercial practice . A test of zirconium as a starting - sheet material showed that it promoted corrosion of the deposit to a lesser extent than aluminum and that the deposit adhered less tenaciously . These two properties lend themselves to the development of ways to strip deposits mechanically from zirconium starting sheets . Titanium was unsuitable for use as a starting - sheet material .

Jan 1, 1963

By Jerry B. F. Champlin

NIOSHAn accelerated testing procedure developed by the Bureau of Mines for evaluating commercially available corrosion inhibitors is described. Ultra-sonic agitation of the corrodent solutions and the hot-finished mild steel test coupons was used to evaluate the effects of several variables on the effectiveness of two corrosion inhibitors. Small changes in the weight of the test coupons in both controlled and inhibited corrodents, before and after exposure, affected the precision and accuracy of the results. Minute amounts of oxygen in the systems were found to be causing the relatively large deviations in the corrosion developed in the controlled tests. Microscopic examination of the test coupons revealed that both surface preparation and internal strains resulting from fabrication methods materially affect corrosion behavior.

Jan 1, 1965

By Wallace W. Roepke

The Bureau of Mines studied the cutting characteristics of point-attack bits to reduce airborne respirable dust and energy during cutting. Linear cutting of two coal types using four bit types at three depths of cut with three space-depth ratios was performed with a modified horizontal milling machine using an optical particle-size monitor for respirable dust sampling. The cutting action of one bit on a rotary hardhead mining machine was mathematically analyzed and compared with the results of the linear cutting test. Airborne respirable dust per unit mass cut (specific dust) was found to be a monotonically increasing function of specific energy. Specific dust and energy decrease with increasing depth of cut. The amount of nonairborne respirable dust was 100 to 1,000 times greater than the airborne dust. The plumb-bob bit produced the most airborne respirable dust and the highest specific energy of the four bits tested. Rotary cutting was a greater dust producer and energy consumer than linear cutting because of the constantly changing depth of cut, space-depth ratio, and attack angle of the bit relative to the horizontal bedding planes. A new cutting technique is proposed to minimize the existing problems of the rotary cutting machines by providing greater production, reduced dust, and minimized methane ignition potential at the face.

Jan 1, 1976

By J. P. Powell

This report provides information on the techniques and results obtained on representative waterflooding projects in Cowley County, Kans. Records show that waterflooding was begun as early as 1935, but not until 1948 was the method expanded. The greater depths to the oil-producing formations in this area compared to those in eastern Kansas undoubtedly delayed the widespread use of secondary-recovery methods. This report presents a discussion of four waterflooding projects in Cowley County, Kans. The locations of these projects are shown in figure 1. The projects have been in operation from 1 to 7 years and have produced more than 1 million barrels of additional oil by injecting 11.5 million barrels of water. The projects are designed to take advantage of elevation and height of the separator tank to collect by gravity flow the produced brine at the respective treating or storage tanks. The closed-type water system is used on three of the projects and an open-type water conditioning system on the fourth. On one of the projects, which was drilled along a narrow shoestring formation, alternate well, were converted to input wells. However, most of the input wells for flooding converted producing wells.

Jan 1, 1958

By Joel N. Van Sant

The rapidly expanding economy of the West, with its growth of heavy industry, and increased steel production, is primarily responsible for the refractory clay industry's concern over the adequacy of the clay supply in States of the Great Plains and Rocky Mountains. Hence, the investigation by the Federal Bureau of Mines of the occurrence and use of refractory clays in North Dakota, South Dakota, Nebraska, Wyoming, Colorado, Utah, New Mexico, and Arizona has been encouraged by the major consumers and producers of this commodity. The Wyoming investigation is a part of the national program devised to close gaps in the domestic supply of specific types of clays to determine their characteristics and properties and to provide information that will assist the refractory-clay industry. Forty-two locations of clay-bearing rock in 17 areas in Wyoming were examined (fig. 1). Location 3 was not examined during this survey. Its description was taken from an earlier report. Locations 20, 21, and 22 were previously reported but were, also, examined by the Bureau. No samples were collected from these locations because field examination indicated that the shales were not refractory grade. The Hulett, Aladdin, and Newcastle areas are discussed in the section on the Black Hills district; the other 14 areas are described separately.

Jan 1, 1961

By K. L. Rubow

"IntroductionAir sampling for airborne contaminants requires a system for moving air, a collection method, and a procedure to determine the quantity of contaminant collected. Because occupational exposure limits and air quality standards frequently are expressed in terms of concentrations, a method of determining the volume of air sampled is also needed. The four principal components in a sampling train are shown in Figure 12-1. The inlet admits the air sample into the train; the collector(s) separates the gas, vapor, or particles from the air; the flowmeter measures the rate or total quantity of air sampled; and the pump (air mover) provides the suction required to draw an air sample through the train. Inlet sampling considerations are discussed in Chapter 21. Various types of collectors are described in subsequent chapters. Flowmeters are discussed in Chapter 7.This chapter will describe the air mover portion of the sampling train and air sampling systems that contain three or four components in a convenient package. The chapter consists of two parts. The first part contains a brief description of the different types of air movers and air sampling systems. The second part consists of tables and figures showing detailed information on a wide variety of commercially available air movers and sampling systems. ient size is filled with a liquid in which the suspected contaminant is insoluble. When the liquid is allowed to escape from the vessel, it is replaced by air from the atmosphere to be sampled. Such an air sample is an integrated sample rather than an instantaneous sample because the mass of fluid requires a finite time to empty. In fact, by employing a large vessel with controlled drainage, this method can be used to move air at low flow rates through a sample collector for extended intervals. Additional discussion of this method can be found in Chapter 17."

Dec 1, 1996

By C. P. Bowie

For years many oil producers have believed that often low-pressure oil- and gas-bearing strata have been over coked in fields where the rotary system of drilling has been used. Collom3/ gave as a reason for this condition that because the mud fluid was thick, the oil or gas stratum was plastered and sealed as the tools passed through it and no oil showed at the surface. Although this observation was made 15 years ago, it may often still be true notwithstanding modern developments in coring and electrical logging. Operators have believed, also, that mud fluid does not solidify behind the casing. Lewis and McMurray4/ stated: "All the evidence obtainable from practical experience points to the fact that the mud fluid properly mixed and employed does not solidify behind the casing, even in deer wells and after long periods."

Jan 1, 1937