Search Documents

By D. E. Redmon

The Federal Bureau of Mines has studied the locations and general features of 90 pegmatites found in north-central New Mexico. The dominant valuable product of the pegmatites is muscovite, both sheet and scrap. However, the Harding pegmatite in Taos County is mined only for beryl. Many attempts have been made to recover scrap mica on a large scale by mechanical beneficiation of pegmatite, but the operations heretofore have been short-lived. The Globe mine and the Apache mine, both near Petaca in Rio Arriba County, have been the most important sources of sheet mica in New Mexico. Recognition of the growing need for some of the minerals derived from pegmatites led the Bureau of Mines to investigate the occurrences of pegmatite.

Jan 1, 1961

By Arthur E. Bruszak, Marcel Vanpée

In many practical combustion systems ignition may occur through contact with hot burned gases . Such a process plays a vital role in flame stabilization on bluff bodies . It is also of importance in the ignition of firedamp by the hot spent gases of explosives used in mines . Also , in the communication of flames through narrow channels , a problem of practical importance in flameproofing electrical equipment , the propagation of the flame is essentially a reignition process in which hot burned gases are the agent of ignition . In the actual ignition problem a great variety of conditions may be visualized . Ignition may occur where pockets of hot gases are surrounded by cold explosive mixtures or where pockets of cold mixture may be surrounded by hot gases . Alternately , a flowing stream of combustible mixture may be initially in contact with another stream of hot combustion products , or a jet of hot gases may flow into a cold quiescent mixture ; the jet may be laminar or turbulent , continuous or discontinuous . The hot gas may also consist of the oxidant ( air for instance ) and the cold combustible pure fuel . This study by the Bureau of Mines is concerned only with ignition produced by a continuous jet of gas ( hot ) flowing into a practically quiescent cold mix- The investigation of ignition by bursts of hot gases or by turbulent jets is outside the scope of this report , and work performed on this phase of the problem has been published elsewhere

Jan 1, 1963

By Wilbur I. Duvall, Thomas C. Atchison, Joseph M. Pugliese

Short cylindrical charges were detonated in drill holes in rock to determine the effect that decoupling ( defined as the ratio of the radius of the hole to the radius of the charge ) has on the strain - generating abilities of explosions in rock . The amplitude and period of the strain pulses produced in the rock were studied as a function of distance , size of charge , and decoupling . The main results of these studies were that , for a given distance and size of charge , the amplitude of the strain pulse decreases as decoupling increases and the period of the strain pulse decreases at first and then increases as decoupling increases . A simplified theory of decoupling is presented that satisfactorily explains the experimental results . The information presented makes it possible to predict the effect of decoupling on explosiongenerated strain pulses in rock and thus helps the explosives user evaluate the effect of decoupling on his blasting .

Jan 1, 1964

By S. H. Ash

The coal-mining districts of Washington are mainly situated west of the Cascade Mountains. The eastern boundaries of Whatcom, Skagit, Snohomish, King, Pierce, and Lewis Counties, shown in Figure 1, form the backbone of the mountain range. The mines are on the foothills of the slope and extend to the shores of Puget Sound in the central and northern portions. The subbituminous fields of Lewis, Thurston, and Cowlitz Counties extend into the valleys west of the mountains. The Roslyn field, a small but important area, Lies on the eastern slope of the Cascade Range. If western Washington is divided into three areas from north to south the bituminous coal fields and most of the active mining operations will be found largely in the central area. In the southern portion there are large areas of subbituminous coals of varying quality extending from Centralia to the Columbia River. In the northern portion, mining is at present practically restricted to one mine which is working a subbituminous bed near the city of Bellingham.

Jan 1, 1931

By George S. Rice

This bulletin traces the growth in the belief in the explosibility of coal dust, summarizes the experiments and mine investigations that have established this belief, and gives the present status of pre- ventive measures. It has been prepared in accordance with the pro- visions of the acts of Congress authorizing investigations relating to the causes of mine explosions, and contains references to and descrip- tions of experiments made at the Federal testing station at Pittsburg, Pa. This station was inaugurated under the United States Geo- logical Survey, and was transferred to the Bureau of Mines on the establishment of the latter on July 1, 1910. Only within comparatively few years has the dry dust of bitumi- nous and lignitic coals been generally recognized as an explosive agent more insidious, threatening, and deadly to the miner than fire damp. Fire damp carries its own flag of warning-the "cap" in the safety lamp-but coal dust, though visible, does not attract attention until present in large quantities. Fire damp is of local occurrence, and except in notable and very exceptional cases is controllable by careful manipulation of ventilating currents. If by mischance a body of fire damp is ignited in a mine, the force of the explosion may be terrific, but the effect is local unless dry coal dust is present, or unless (as it very rarely happens) an explosible mixture of methane gas and air extends through large areas of the mine. In a dry mine dust accu- mulates everywhere, and the blast from the ignition and combustion of bituminous dust may traverse miles of rooms and entries and wreck structures at the entrance to the mine. The comparative potential destructiveness of gas and of bituminous dust is strikingly shown by the history of the Pennsylvania anthracite mines. These mines not infrequently have large inflows of gas, and the resulting mixtures of gas and air have sometimes been ignited, yet no such wide-sweeping explosions have taken place, despite the presence of dry anthracite dust, as have happened in excellently ventilated bituminous mines.

Jan 1, 1911

By O. H. Metzger

This is one of a series of capers being published by the Bureau of Mines on gold mining A the Western States. It describes the production of gold in the principal mining districts of New Mexico. The material was gathered red on a trip through tale State in the summer of 1936. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of mine operators in all parts of the State, who willingly contributed all information requested. Geological reports of the Geological Survey and the New. Mexico Bureau of Mince were drawn upon freely for information; credit to individual paper, is given in the text.

Jan 1, 1938

By H. R. Batchelder

The Bureau of Mines Gas Synthesis Demonstration Plant at Louisiana, Mo., includes apparatus for the gasification of pulverized coal with oxygen and superheated steam. A pebble heater constructed by the Babcock & Wilcox Co. is used to superheat nominal 5-pound steam for the gasification process, usually to temperatures of 1,600° to 2,300° F. with flow rates of 1,400 to 2,300 pounds per hour. Heaters of this sort have been described. So far as is known, the Babcock & Wilcox Co. is the sole commercial manufacturer of equipment of this type. Units have been built with capacities above 18,000 pounds of steam per hour.

Jan 1, 1951

By A. T. Coumbe

The first survey 3/ covering sales of liquefied petroleum gases was made in 1930 by the Bureau of Mines, which at the time was under the United States Department of Commerce. This original canvass covered national totals for 1922 through 1929, and most of the supply came from natural gasoline plants. The 1930 report showed approximate totals for butane and propane and for butane-propane mixtures and pentane grouped together. No attempt was made to breakdown the national sales by various uses until 1931, when the quantities for domestic or household consumption, gas manufacturing, and industrial requirements, including miscellaneous uses were indicated. As the market for these liquid petroleum gases expanded and as new uses came into importance, their respective quantities were shown separately in the annual survey. Sales for internal-combustion engine fuel and for raw material for chemical plants were first taken out of the industrial total in 1936. During World War II liquefied petroleum gases became important as feed stock diverted to synthetic rubber plants, and consequently the survey was broadened to cover this particular demand, beginning in 1944. Pentane was dropped from the survey after 1943, as, being liquid at atmospheric pressure, it is not considered as one of the liquefied petroleum gases and furthermore, the quantity reported made up less than 1 percent of the total sales. Thirteen producing companies reported to the Bureau in the first survey made in 1930, and in the 1952 canvass about 130 producers--petroleum refiners and natural gasoline companies--and about 1,300 dealers cooperated by filing schedules showing a breakdown of their sales. Their 1952 deliveries of approximately 4.5 billion gallons of liquefied petroleum gases were equivalent to about 3.4 billion gallons of gasoline or 3.1 billion gallons of distillate fuel oil.

Jan 1, 1954

By Noel N. Moebs

This report summarizes a Bureau of Mines study on the use of geotechnology to identify and reduce ground control hazards at slate quarry operations in eastern Pennsylvania. The major ground control hazard is falling rock, attributed to weathered bedding plane faults, which weaken quarry highwalls. It was demonstrated that these faults can be detected outside of the quarry perimeter using surface resistivity measurements. Falls of ice from quarry highwalls constitute a second major hazard, which requires water diversion as a basic control method. In situ stresses seemingly cause only minor problems in slate extraction although they could interact with developed stresses and lead to failure of barriers between quarries. Pull tests showed that rockbolts anchor firmly in slate and should prove effective in securing loose rock.

Jan 1, 1986

By Frederick C. Trutt

A guide to the utilization and development of extensions and modifications to the APL Mine-electrical-system Load-flow Program is presented. These modifications include the development of algorithms to minimize computational operations within the iterative-solution techniques, as well as minimization of the number of required iterations. Extensions to the load-flow program include the development of algorithms for the calculation of balanced faults, simplified specification of fault parameters, optional inclusion of pre-fault currents, and an alternate-solution technique.

Jan 1, 1978

By David E. Swanson

The U.S. Bureau of Mines undertook a basic investigation of collimated abrasive water-jet behavior because a more complete understanding of the fundamental process may lead to further technical advances. Laboratory experiments used 2-mm water-jet nozzles and new entrainment apparatus to analyze collimated abrasive water jets operating under varied conditions. Maximum water pressure was 69 MPa to permit use of conventional hoses with a burst-to-operating-pressure ratio of 4. Nozzle and induction line pressures, abrasive induction rates, and jet reactive thrust forces were recorded for each operating condition. Average jet velocity and power were determined from component mass flow rates and reactive thrust force measurements. Relative velocity and cross-sectional distribution of abrasive particles were determined using impact analysis techniques. Other jet characteristics were determined photographically. Properties of free water jets, collimated water jets, and collimated air-water jets were determined for comparison.

Jan 1, 1989

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By Paul Hatmaker

Lime was a highly useful commodity thousands of years before the simple chemistry of its manufacturing process was known. The employment of lime for agriculture, building, and even certain essentially chemical purposes is so old that its origin is among the unrecorded details of man's first ventures into the manufacture and use of prepared substances. Lime is a most versatile material and consequently has come to be widely utilized in modern civilization. Immediately before the depression of the early 1930's the annual production of lime in the United States was more than 4 million tons, valued at 33 to 42 million dollars. This output was sold to many industries, so many that mere enumeration becomes tedious. In addition to agricultural and building lime the sales statistics compiled annually by the Bureau of Mines include lime sold to the steel and other metallurgical industries as refractory and fluxing material, as well as that used by paper mills, glass works, tanneries, and water-treatment plants. These major uses normally consume about 86 percent of the domestic sales. The remaining 14 percent includes lime sold for use in the manufacture of alcohol, alkalies, bleaches, calcium acetate, calcium carbide, coke gas and byproducts, glue, insecticides, oils and fats, paints, and rubber, in the refining of salt, in the manufacture of sand-lime and slag brick, in the disposal of sewage and garbage, in the manufacture of silica brick, in the refining of sugar, in the textile industries, and in wood distillation. Many other uses are also known for which complete sales data are not available.

Jan 1, 1934

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By R. W. Stahl

A survey of firefighting facilities and practices in coal mines conducted by the Bureau of Mines3/ showed such variations in equipment and apparent attitude toward fire protection that a comparison with other industry seemed advisable. Although other industry is confined generally to surface operations and the hazards probably are not as great, the same general methods of extinguishment are employed, so that the cost and protection at least should be comparable. An investigation of industry other than mines revealed a generally greater emphasis placed on fire-combating equipment, fire-brigade training, fire-fighting facility inspection, and fire-hazard elimination, as well as a greater average expenditure for fire protection.

Jan 1, 1959

By H. E. Powell

Basic data were recorded on the decompositions that take place during thermal decomposition of siderite (FeC03). Both the naturally occurring and a synthetically prepared mineral were studied by differential thermal, thermo-gravimetric, X-ray-diffraction, and chemical (including gas) analyses. Thermal decomposition was studied in the media of dry air, moist air, dry carbon dioxide, dry helium, and dry carbon monoxide and at atmospheric and at reduced pressures. Results showed the thermal decomposition of FeC03 to be an extremely complex process, dependent on environmental factors and side reactions that cannot now be completely controlled. Therefore, full understanding of the reaction involved must depend on additional research with advanced evaluation techniques.

Jan 1, 1965

By C. W. Davis

During the second year of its existence, the Ore-Testing Section has actively prosecuted work in the standardization of testing methods, in conducting routine tests and analyses for other Government agencies, and in the determination of recommended processes for the treatment of representative ores from mining districts. Close cooperation has been maintained between the members and units of this Section and those of other Sections, J. A. Woolf and J. B. Clemmer have continued to act in an advisory capacity and R. E. Head has contributed valuable assistance in the microscopic examination of ores and metallurgical products that did not respond readily to standard treatment methods.

Jan 1, 1938

By C. W. Davis

During the second year of its existence the Ore-Testing Section has actively prosecuted work in the standardization of testing methods, in conducting routine tests and analyses for other Government agencies, and in the determination of recommended processes for the treatment of representative ores from mining districts. Close cooperation has been maintained between the members and units of this Section and those of other Sections. J. A. Woolf and J, B. Clemmer have continued to act in an advisory capacity and. R. E. Head has contributed valuable assistance in the microscopic examination of ores and metallurgical products that did not respond readily to standard treatment methods.

Jan 1, 1938

By James F. Devine

The radial, vertical, and transverse components of particle velocity were recorded by Bureau of Mines investigators along gage arrays extending in one or two directions for 145 to 3,170 feet at five quarries. Of the 39 quarry blasts, 12 were instantaneous blasts, 5 were of the one hole per delay type, using millisecond delayed caps, and 22 were multiple hole per delay type employing millisecond delay detonating fuse connectors. Charge weight per hole ranged from 8 to 1,500 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 25 to 4,620 pounds.

Jan 1, 1966

By Paul Meadows

The Buckrange reservoir, Stephens field, Ark., is approaching the economic limit of production under present operating conditions. Over 100 million barrels of oil remaining in the reservoir will not be recovered by primary producing methods. The Bureau of Mines, in cooperation with the Arkansas Oil and Gas Com-mission, made the petroleum-engineering study presented in this report to aid operators in evaluating secondary-recovery possibilities in the reservoir and in planning secondary-recovery programs if their initiation is decided. The Stephens field, in Columbia, Nevada, and Ouachita Counties, Ark., is about 12 miles northeast of Magnolia, Ark., and 15 miles west of the Smackover field. Surface elevations in the area average about 240 feet above sea level.

Jan 1, 1956