Search Documents

By J. C. Edwards, C. C. Hwang

In ventilated tunnel fires, smoke and hot combustion products may form a layer near the ceiling and flow in the direction opposite to the ventilation stream. The existence of this reverse stratified flow has an important bearing on fire fighting and evacuation of underground mine roadways, tunnels and building corridors. In the present study, conducted by the National Institute for Occupational Safety and Health, a CFD program (fire dynamics simulator) based on large eddy simulations (LES) is used to model floor-level fires in a ventilated tunnel. Specifically, the critical ventilation velocity that is just sufficient to prevent the formation of a reverse stratified layer is simulated for two tunnels of different size. The computer code is verified by checking the computed velocity profile against experimental measurements. The CFD results show the leveling-off of the critical ventilation velocity as the heat release rate surpasses a certain value. At this critical ventilation, the ceiling temperature above the fire reaches a maximum for both tunnels. The velocity leveling-off can be explained from this observation. An extended correlation of Newman (Combust. Flame 57 (1984) 33) is applied to the temperature profiles obtained by CFD. At the critical ventilation, temperature stratification exists downstream from the fire. The computed critical ventilation velocity shows fair agreement with available experimental data taken from both horizontal and inclined fire tunnels. The CFD simulations indicate that the Froude modeling is an approximation for tunnel fires. The Froude-scaling law does not apply to two geometrically similar fire tunnels. The CFD results are compared with two simple theories of critical ventilation by Kennedy et al. (ASHRAE Trans. Res. 102(2) (1996) 40) and Kunsch

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By Sean Gallagher

The vast majority of ergonomics research has addressed the demands of work in standing or sitting postures, and understandably so. However, many workers (for example, underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, and others) are often required to adopt postures such as kneeling, stooping, squatting, or lying down for significant periods of the work day.

Jan 1, 2005

By L. H. Wullstein

Nitrogenase activity (C2H2 reduction) was found to be associated with the following grasses in the field: Agropyron dasystachyum, Agropyron smithii, Aristida purpurea, Oryzopsis hymenoides and Stipa comata. Uptake of fixed nitrogen was also demonstrated for these grasses. Two unidentified nitrogen fixing bacteria were isolated, one from Stipa comata and one from Aristida purpurea. Cynodon dactylon and Agropyron cristatum were successfully inoculated with the unknown isolate obtained from Stipa comata. The inoculated plants exhibited nitrogenase activity (C2 H2 reduction) whereas uninoculated controls gave negative results.

Jan 1, 1982

By Forrest T. Moyer

INJURY experience and employment data are presented in this (chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron-blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume III. The 1963 figures are preliminary and are subject to revision. METAL MINES Preliminary estimates for the metal-mining industry of a combined fatal and nonfatal injury-frequency rate of 32.34 per million man-hours in 1963 indicate only a slight change from the rate of 32.00 in 1962. Metal operations had 41 fatal and 3,110 nonfatal injuries during 1963.

Jan 1, 1964

By John P. Hansen

Batches of red or brown iron ore concentrates, weighing 100 or 200 grams, were reduced with gaseous reductants in a laboratory-sized fluidized-bed reactor. Using a loss of weight technique, the rates of reduction were measured and the effects of temperature, gas consumption, and gas flow rates were determined. Below about 725° C the rate of reduction was controlled by the chemical reaction at the reduction interface having an activation energy of about 10 kcal/g mole. Above about 725° C the rate of reduction appeared to be controlled by the flow of the gaseous reductant and therefore to be directly proportional to the flow rate. Above 725° C, hydrogen reduced the iron ore much faster than carbon monoxide. In gas mixtures, carbon monoxide or nitrogen reduced the hydrogen partial pressure and lowered the reaction rate proportionally. When present in large concentrations, carbon monoxide had a serious inhibiting effect on the reduction rate, probably owing to carburization and sintering of the reduced iron.

Jan 1, 1970

By T. Muldoon

Literature review and extensive field survey of line and check curtain materials and practices showed: ? Miners, in general, know how to set tight curtains, and do so when needed. ? The tradeoff is economic; tight ventilation is labor-intensive. Line and check curtain techniques found are catalogued and evaluated. A fieldworthy 10 ft extensible brattice to maintain a 10 ft setback was found in use in two mines on continuous miner faces. This technique was evaluated in the laboratory for leakage and methane control at the face. Significant results include: 1) Air leakage through a gap in the extensible curtain depends upon the ratio of the cross-sectional areas between entry and return as well as gap area; 2) Gap shape has no significant effect on methane concentrations at the face -increasing gap area diminishes ventilation effectivness; and 3) Substantial reductions of CH4 concentrations at the face were accomplished by brattice extensions with gaps of up to 5 ft2 in area. An "inby hook," inserted in the roof automatically to make possible the deployment of a longer (20 ft) brattice extension in the context of a remotely controlled miner, was tested in various roof types. Insertion of this design succeeded only in coal.

Jan 1, 1982

By R. L. Rickel

The Bureau of Mines, as part of its minerals environmental technology research, conducted a study of mine waste tailings disposal. Part of the investigation evaluated the sand bed dewatering technique for disposal of alumina mini plant tailings as a means to increase consolidation rates and contain effluents. The technique employs a bed of sand resting on an impervious bottom. The tailings slurry is impounded over the sand layer and is dewatered through bottom drain piping. The study employed a single 10-ft-high, 6-in-diam, clear polyvinyl-chloride (PVC) column, and thickener wastes from the acid leaching of calcined kaolin clay. Results showed a consolidation rate of 41 in in 186 days for a total volume reduction of 37 pct. Sand bed dewatering was an efficient technique for solid consolidation and effluent containment when compared with data obtained from other dewatering studies.

Jan 1, 1982

By Joseph T. Singewald

The term "titaniferous magnetite" is used to designate those magnetic ores of iron that carry more than 2 or 3 per cent of titanium. Large and easily workable deposits of these ores occur in different parts of the world, and have attracted attention for many years. Under present furnace practice, however, the smelting of these ores is both difficult and expensive, and for that reason they are not accepted by furnaces, so that the deposits are practically worthless. The problem of finding a feasible method of utilizing these ores has naturally been attractive, and numerous attempts have been made to solve it. Experiments to that end embrace two lines of investigation. The one that has been the more frequently tried is the elimination of the titanium from the ores, so as to make possible their smelting in the usual way. The other is the devising of a method of smelting by which titaniferous ores may be reduced as economically as are non-titaniferous ores. The former method involves a physical process, the latter a chemical process.

Jan 1, 1913

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

By E. Owens, R. Gudavalli, D. Wilder, T. Xia

As mechanical shock and vibration environments evolve, it is important to understand their potential effect on human operators. Human beings are sophisticated mechanisms comprised not only of passive components with mass, damping, and stiffness characteristics, but also of components that can actively affect apparent mass, stiffness, and damping. Because the lumbar spine can exhibit local, short-column buckling, stability of the human trunk depends on the responsiveness of the neuromuscular control system.1-2 We have been evaluating the ability of patients with back pain to respond to a series of sudden loads. We believe the results have implications for isolation design and standards development. Methods 153 patients, aged 21 to 55, presenting with back pain agreed to enroll in a research study that randomly assigned them to one of three treatment arms: high velocity low amplitude spinal manipulation, low velocity variable amplitude spinal manipulation, or wait for 2 weeks and then be randomized to one of the above groups. Response to sudden load testing was one of a battery of baseline evaluations performed upon entry into the study and prior to treatment. EMG electrodes were attached to the skin over the paraspinal muscles of the standing participant bilaterally 3 cm from midline at the L3 level. While standing upright on a force plate (Bertec), participants were fitted with a strap around their back and hooked to a load cell in front of their chest. An accelerometer was rigidly attached to the load cell. Impact was applied to the chest using a cord attached to a falling weight. The weight’s fall distance was varied between 9 and 13 inches to account for the size of the subject. The subject was blindfolded and wore headphones playing white noise to prevent cueing of when the weight was dropped to apply the load. Hence, although the participant knew a load was about to be applied, he or she did not know the instant it would occur. Just before the weight was dropped, a 4 second data collection process was started for the two EMG electrodes, load cell, accelerometer, and force plate. The load drop was repeated 6 times, at irregular intervals, over a period of 2 minutes. The raw data thus collected was reduced to obtain several values: 1) length of time from the pull on the harness to the beginning of the response of the left and right paraspinal muscles (LES, RES), 2) time and magnitude of the maximum response, 3) force and acceleration experienced at the chest, and 4) the time and magnitude of the center of pressure location (COP). A general linear model was used to evaluate the results. Results For the EMG data, of the 1,824 observations made, 90% of them indicated a response. Prior to the sudden load, resting muscle activity was different between left and right sides (p=0.0001) and between males and females (p=0.0001). Female subjects began to respond to the sudden load within 92 to 110 ms and males from 101 to 109 ms. Females exhibited more variation in starting

Jan 6, 2006

By Leonard Obert

This report describes a gage which, when used with my procedure for producing strain relief, will measure the resulting borehole deformation, From the borehole deformation the magnitude and direction of the principal stresses in a plane normal to the axis of the borehole can be calculated. The design considerations, mechanical construction, sensitivity, and stability of the gage are discussed. INTRODUCTION During the past two decades an increasing mount of consideration has been given to the problem of measuring and evaluating stress in rock around underground openings. Several investigators have made theoretical and model studies of the stress and (or) strain concentrations around simulated mine openings or in structural members, such as mine pillars or immediate roof. Other investigators have developed gages for directly or indirectly measuring stress or strain, and a number of reports present the results of measurements made with these gages. Because various methods and instruments have been developed, factors involved in this type of measurement will be briefly considered.

Jan 1, 1962

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground nine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.8 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated. Rock dust was employed chiefly in the larger mines, which numbered only 431 out of 6,016 underground mines in operation in 1935, according to reports from mining companies. The mines in which rock dust was used had an average of 288 underground employees per mine, whereas mines in which rock dust was not used averaged only 62 underground employees per mine.

Jan 1, 1940

By T. N. Williamson

Most U.S. coal production is bituminous coal. Some 90% of current production comes from a geographical area enclosed in a circle with a 300 mile radius and its center at about Huntington, West Virginia. There are important underground coal production areas in the western parts of the United States as well. Most U.S. coal production comes from fairly level seams, many of which pitch rather uniformly only a few feet per mile. Usually there will be several overlying seams of varying thicknesses, separated by several tens of feet. Fig. 1. 1. Seams have minor local undulations but these? are small enough not to be a major consideration in a horizontal drilling research program.

Jan 1, 1970

By Fred D. DeVaney, C. W. Ambler

"Copper sulphate is a common flotation reagent for blende ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation feed may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss.That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.This problem has been the basis of a study undertaken jointly by the Mississippi Valley Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, at Rolla, Missouri. Its importance may be understood better when the tonnage of zinc ores now being treated by flotation in this country is considered. According to Gaudin4 5,536,244 tons of zinc or were treated by flotation during 1927. In these operations copper sulphate was employed as an activating agent; the amount per ton averaged 0.81 pound for straight sulphide zinc ores and 1.16 pounds for complex ores. Since such large quantities of zinc ore are treated by flotation and since metallic iron is always present, the importance of studying their reactions on each other and the effect of their reaction"

Dec 1, 1929

By T. G. Carnahan

In-place leaching is being actively utilized to extract uranium, copper, and evaporites from low-grade and difficult-to-mine ores. The purpose of this report is to discuss in-place leaching technology, its advantages and disadvantages, and to give an overview of past, current, and envisioned in-place leaching operations in the U.S.A. Application of in-place leaching to uranium ores has been particularly successful because the conditions for leaching are nearly ideal. The ores are generally in highly permeable sandstone aquifers bounded above and below by impermeable shales. The uranium ore minerals are easily leached with oxidizing acid or base solution and the pregnant solutions are amenable to ion exchange concentration and purification prior to conventional solution neutralization for recovery of yellow cake. Copper is routinely recovered from sub-grade rock by dump leaching at most major copper mines. Acidified ferric sulfate is either sprayed on the surface of the dumps or is ponded on top of the dumps. The leaching solution migrates down through the rock and dissolves copper. The solution is collected from the base of the dumps and copper is recovered by solvent extraction-electrowinning or by cementation on detinned steel cans. True in-place copper leaching is being practiced in the caved stopes of an exhausted underground copper mine. Other innovative in-place copper leaching techniques have been tested commercially and laboratory- and pilot-scale experiments have been conducted to investigate proposed in-place leaching techniques for extracting copper from difficult-to-treat chalcopyrite ores. Solution mining of evaporites is being conducted commercially for the extraction of sodium chloride and potassium chloride. A large-scale experimental project for solution mining of trona has been undertaken.

Jan 1, 1982

By David R. Wilburn

The U.S. Bureau of Mines investigated the resources, costs, capacities, market relationships, and short-and long-term supply of bauxite, alumina, and aluminum. The 45 evaluated mines and deposits in 14 market economy countries (MEC's) have a demonstrated resource of 8.4 billion mt of bauxite and an aluminum content of approximately 2.1 billion mt. Developed world bauxite resources and existing primary aluminum smelting and refining capacity are sufficient to satisfy demand through at least 1995, when additional properties (with higher cost levels) would need to be developed to satisfy future demand levels. It is anticipated that new alumina or aluminum production most likely would occur in developing regions with large bauxite potential, low-cost energy sources, and a close proximity to refining and/or smelting capacity. An increase in aluminum recycling capacity would help meet future demand increases. A series of network model supply analyses was performed for the period 1988 through 2000. Based on announced future production levels and assuming demand grows at the level outlined in the analyses, model results indicate there is sufficient material available to meet demand until 1998, where-upon an aluminum shortfall is projected. Additional analyses investigated the effect of a reduced growth rate of demand and regional production variations in Venezuela on the international aluminum industry.

Jan 1, 1993

By August J. Kwitowski

This Bureau of Mines report summarizes the development of a protective operator compartment for a new generation thin-seam mobile bridge carrier. The developed compartment is commercially available and is currently employed on approximately 15 bridge carriers used in the mining industry. The design of the compartment, which employed human factors engineering and small- and full-scale mockup models, is fully described. Details of the compartment's fabrication, evaluation, and demonstration in a commercial low-seam coal mine are also provided.

Jan 1, 1986

By Hideo Ando, Yuka Satou, Tatsuya Ishitake

Whole-body vibration occurs when the body is supported on a surface which is vibrating. Occupational exposures to whole-body vibration mainly occurs in the transportation industry, but also in association with other industrial process. Epidemiological studies have frequently indicated an elevated health risk for the spine in workers exposed to whole-body vibration. With regarding to train or bus operators, a fall of drivers’ wakefulness level because of fatigue is often pointed out. This decrease in wakefulness results in an increase of the occurrence of accidents. However, a study of how whole-body vibration affects people's level of wakefulness has not been done. To test the hypothesis that exposure to whole-body vibration has a certain effects on level of wakefulness, the change of a subjective wakefulness level and changes of electroencephalogram (EEG) were observed under experimental exposure to short-term whole-body vibration. Methods Subjects are ten healthy male university students, with an average age of 20.7 ± 1.8 years old, and they are all nonsmokers. Using the equipment (CV-300, AKASHI) of whole-body vibration generator, we consider an exposure environment of actual driver work, so that set the frequency and the acceleration level as 10 Hz and 0.6ms-2 r.m.s.. The subjects were exposed to whole-body vibration in the seated position and exposure time was fixed for 12 minutes. Subjective wakefulness level was evaluated using the questionnaire of VASS (Visual Analog Sleepiness Scale) and KSS (The Kwansei Gakuin Sleepiness Scale). For the electroencephalogram (EEG) measurement, it was equipped with the electrodes based on the International ten-twenty electrode system (C3-A2, O1-A2, O2-A1). EEG activity in the alpha frequency band (8 – 12 Hz) is one of the most typical physiological indicator which represent the transition from wakefulness to sleepiness. AAT (Alpha Attenuation Test) which repeats three times each opened and closed eye for 1 minute was performed in a seating position with directions of the researcher in the beginning, in the middle and in the end of exposure to whole-body vibration. For analysis, power spectral analysis was conducted over the last 6 min of EEG, and wakefulness levels were defined as the ratio of mean alpha power during eyes closed versus eyes opened. The laboratory was kept at room temperature (21 ± 1.0 degrees C), humidity was 50 ± 5%, noise level was 63.6 dB (A) eq, and illumination 510 lx. Each experiment was started around 10:00 am to minimize the effect of biorhythm.

Jan 6, 2006

By M. E. Volin

The Smuggler is one of the mines in the Aspen district, located the central part of Pitkin County, Colo. It was first examined in July 1943 by C. R. Wilfloy, former mining engineer of the Bureau of Mines at Salt Lake City, Utah, in, company with the lessees, R. D. Rohlfing of Aspen and J. W. Vanderwilt of Denver. The purpose of this examination was to sample a mineralized breccia zone that appeared continuous along the contact between the Leadville and Weber formations. These preliminary samples showed that the zone contains low but significant amounts of lead and zinc and that the minerals are partly oxidized and thus not easily concentrated. The mine was examined again in May 1946 by the senior author and William Herron, one of the present lessees of the property. This examination reviewed the previous sampling and recommended investigations by the Bureau of Mines. Sampling and drilling investigations were conducted by the Bureau from October 1946 to February 1947 and again from August 1947 to April 1948. Aspen is the center of a famous mining district that produced over $102,000,000 in silver and lead ores from 1880 to 1918, when a dispute closed down the mines (fig. 1). All of the workings below the Cowenhoven tunnel in Smuggler Mountain and the lower Durant tunnel in Aspen Mountain have been flooded since that time. The Cowenhoven portal now is caved, and Smuggler Nos. 1 and 2 tunnels are the only accessible workings in Smuggler Mountain. The only operating mine is the Midnight, situated 4 miles south of town at an altitude of 9,700 feet.

Jan 1, 1950