Search Documents

By D. Bartley, R. McClure, W. Reisz

Ever since the 8ms criterion was developed in the early 60’s there has been an ongoing debate among many blasters as to its actual value in controlling ground vibration. The perpetuation of the myth surrounding the 8ms window can be partly attributed to its simplicity and convenience as a means for regulatory compliance. Unfortunately, the mindset that many blasters have adopted has hindered the development and use of more effective techniques and in many cases can actually be counter productive to vibration control.

Jan 1, 2006

By P D. Katsabanis, W Roberts

Commercial explosives exhibit non ideal behaviour which is very difficult to model. The fume spectrum produced by commercial explosives apart from its practical significance for underground mining is of great theoretical importance since it reveals information about the chemistry of the detonation process. Emulsions, watergels and dynamites were tested under various degrees of confinement in an one cubic metre closed chamber. Sand, concrete, steel and copper pipes were used to alter confinement. The degree of confinement was found to significantly influence the quantity (litres/kg of explosive) and the relative proportions of toxic and non-toxic fumes (percent of total fume measured). These results lead to further confinement testing using various rock materials. Fume results, and thus detonation performance were found to be dependent on the type of rock material used for confinement. Materials such as dolomite, limestone, and granite were found to result in a relatively high detonation efficiency of the subject explosive as shown by the distribution of detonation fume products. Conversely materials such as sandstone, talc and massive sulphide resulted in fumes suggesting low relative detonation efficiency. Fumes appear to be a sensitive indicator of the completeness of reactions occurring within the expansion zone of the composite emulsion explosive, while the detonation velocity is relatively insensitive to small variations in confinement. Estimates of sonic velocities of the confining rock materials were found to show no correlation with VOD results. However good correlation between fume results and sonic velocity suggests that the performance of an explosive as indicated by the resulting fume spectrum is affected by the degree of confinement.

Jan 1, 1992

By Dale Preece, Stephen Chung

Mining and quarrying industries recognize blasting as the most effective method for breaking and removing large volumes of rock. However, the economics of blasting are often offset by the costly trial-and-error approach. Researchers in the field of blasting therefore design models to help eliminate the number of trials before finding the best feasible solution. Because of the complexity of blasting, a capable model would allow the designer to look at more than one variable at a time so that the most critical factor can be tackled.

Jan 1, 2002

By Theodore C. Hile, Floyd P. Henry, Ken Gragg

"Conventional explosive-storage methods usually rely on combinations of earth and concrete barriers, along with sufficient distance between limited explosive loads, to avoid accidental conflagration. However, under many circumstances, Air National Guard (ANG) facilities co-located with civilian airfields have trouble meeting necessary Quantity-Distance (Q-D) requirements for Explosive Hazard Class/Division 1.1 and 1.4 materials. Because of the danger posed by explosives stored in earthcovered magazines (ECMs) too close to civilian activities, ANG units often find itdifftcult to maintain adequate stores of ordnance needed to meet unit mission goals."

Jan 1, 1999

By Dale Nies

In the past, cap and fuse has been the only economical and efficient initiation system capable of providing sequential timing, ease of loading and hookup, and unlimited borehole number for backstope rounds. Unfortunately, in spite of these advantages, several negative factors inherent to the system have always been noted. Due to the long, narrow nature of backstope rounds at the Sunshine Mine, the cap and fuse system results in very long, inaccurate delay times. The system was also occasionally unreliable under all the conditions encountered, which in turn could cause potential safety hazards.

Jan 1, 1989

By Michael S. Wieland

The stress waves generated during delay blasting in underground or surface mines not only fracture the surrounding coal, rock, or other strata, but also impact delayed charges remaining in neighboring boreholes. This crossing wave interaction is a ubiquitous fundamental damage mechanism, ultimately responsible for numerous occurrences of misfires and flyrock. The hazards and waste from wave-induced malfunctions are Just the recognized tip of the iceberg. Undetected marginal performance of damaged delay detonators and desensitized charges poses a tremendous unresolved problem, resulting in the reduction of mining profits and the certain retention of unwanted risks.

Jan 1, 1988

By Alan Tordoir, Mark Roberts

The drill and blast process is a critical function within the production cycle which significantly impacts the ability of an operation to effectively meet its safety and production targets. Acknowledging that D&B design and reconciliation practices were conducted inconsistently across operations, a Group wide initiative was launched to embed a standardized design and reconciliation platform in line with the company’s Operating Model principles. A technical system was selected to deliver the digitalization of critical D&B information and enable ‘analyze and improve’ routines for design compliance monitoring and downstream productivity optimization.

Jan 1, 2019

By M. Gebhardt, J. Johnson, S. Rosenthal

The use of presplitting applications in an underground mine setting is a method of reducing overbreak in the rib and back when blasting occurs. Presplitting performed at the Underground Mine Education Center (UMEC) on Montana Technological University’s campus in Butte, Montana showed a dramatic decrease in the amount of overbreak incurred in the blasting process. Application of the presplitting technique occurred after presplitting presentations at ISEE in San Antonio. Presplit testing consisted of drilling perimeter holes closer together than production holes and loading perimeter holes with a combination of specialized presplit explosive and packaged emulsion with electronic detonator initiation. The ideology was to shoot the perimeter row first, to create a fracture around the perimeter, so when the main production round is shot there is less shock exerted on the surrounding walls due to the pre-fractured perimeter rock. For the test performed, the back ended up with 83% of total holes resulting in half barrels representing a remarkable result. The right rib ended up with one half barrel visible before muck was removed while the left rib did not have any half barrels visible due to a clay seam being in very close vicinity to the perimeter row. The first test blast was a great start encouraging future work on presplitting applications in the UMEC. Additional testing will continue with different combinations of perimeter hole spacing, the addition of a buffer row along the ribs, and varying loading techniques to determine the most effective presplit method for the rock type of the UMEC. Detailed test results and loading configurations will be provided in the paper.

Jan 1, 2024

By Martin Chenoweth

The Metropolitan Water District of Southern California (MWD) is undertaking one of the nations largest water management projects. The Eastside Reservoir Project is being built to insure a supply of water to Southern California in the event of earthquake damage to the aqueducts supplying the region. An 800,000-acre-ft lake will result from the three dams, closing off the valley between two parallel ridges. The single largest contract of the project, the West Dam, was awarded to the joint venture of Atkinson Construction Co., Washington Construction Co. (Morrison Knudsen Co.), and HB Zachry Co. Over 50 million bank cubic yards of rock must be drilled and shot on this contract alone. AWZ relies on the TechBASE database management system for documenting drilling and blasting. The database format of TechBASE allows all production parameters to be linked to the location of the activity. This allows parameters such as drill penetration or boulder production to be analyzed for geologic trends that can either be exploited or dealt with. Shot locations are stored as 3D polygons in a polygon table. Production and cost data are stored in flat tables. Shot names are unique and link the polygon table to the flat table. This allows typical database queries to be made by date, location, cost or any production parameter. The output from these queries can be presented in table, graph and as map formats. The map output is particularly helpful in quantifying geologic conditions and blast performance. The ability to transform the data into information has been very helpful. The ability to present this information graphically has been invaluable.

Jan 1, 2000

By Phil N. Bradbury

"During a routine belt tightening of all cost centers, the management at the Martin County Coal Surface Mines, located in Martin County Kentucky felt that a thorough investigation of the drilling and blasting program could possibly pinpoint areas where the cost could be cut without sacrificing production. Upon close inspection of the drill benches it was noted that the actual layout of burden,spacing and stemming varied a bit from the actual blast design that the management had outlined for the blasters. This paper will outline the method of reducing the drilling and blasting cost at the Martin County Coal Operation."

Jan 1, 1986

By John F. Mitchell

Large production blasts involving many series in parallel have long been a source of complication. When speed and accuracy are most necessary in blast preparation an efficient and precise method of wiring is required. After loading a large number of holes and being pressured for time, due to lack of daylight, equipment shutdown, etc., an effective hook-up plan can eliminate many last minute problems. It is the intention of this paper to offer a simplified wiring proceedure which when employed can save precious time and encourage efficient and economical utilization of blasting personnel and material.

Jan 1, 1976

By Karl E. Burgher

Accidental explosions occur throughout the world. They can happen at chemical plants, fireworks plants, grain depots, or as a result of collisions involving volatile or hazardous chemicals. It is interesting, as we know as blasters, that we can take two very harmless products and mix them under certain conditions and produce a violent explosion. It is often very difficult for the investigator to determine the magnitudes of blasts after the fact. However, an estimate must be made to settle vibration and airblast damage claims. The blasting consultant or technical representative is often called upon to act as an expert to mitigate these claims.

Jan 1, 1993

By S B. Richardson, N T. Moxon, A C. Torrance

In many mining situations the energy released by an explosive is far too high and results in over fragmentation and excessive damage to the surrounding strata. Laboratory experiments have demonstrated that the shock energy of an explosive can be significantly reduced by surrounding it with an attenuating material such as a foam. The effect of this reduction in shock energy on fragmentation has been determined using model materials. A four fold reduction in the amount of minus 8mm material relative to an air decoupled charge of the same weight was obtained for a foam attenuator.

Jan 1, 1989

By Chang-Ha Ryu, Hyung Yang, Hyung-Sik Yang

Ground vibration by rock blasting causes many environmental problems to adjacent structures and human bodies. Growing concerns have been given to the effects of dynamic loading induced by blasting works near safety-related structure like nuclear power plant, hospital, broadcasting station, research institute and tish farm, etc. In order to ensure the safety, rational safe criterion should be established. It requires development of a model to predict the design parameters through more systematic measurement and analysis. Primary estimation by adequate model with general parameters will be very useful for safe design and understanding the possible hazards in advance.

Jan 1, 2001

By Bill Runner, James T. Ludwiczak

During the last few years, there has been a flood of local, state, and Federal government regulations concerning blasting. Many of the laws and regulations were written by individuals who know little about explosives, the purpose of blasting, or blasting vibration and damage. I feel that the special interest groups responsible for some of these regulations are not trying to regulate blasting, but to stop it completely by unreasonable, non-flexible, regulations. The most recent being the Office of Surface Mining regulations that are already spreading to the quarry industry and will, no doubt, spread to all blasting involving disturbance of the surface.

Jan 1, 1979

By Zhang Qi

For the most part, the flying piece is serious endangerment in the demolition blasting. To prevent the endangerment, a large number of materials are needed as the protection. Therefore, the determination and design way of the flying distance of piece in demolition blasting have been concerned extensively. Previously, the experienced or half experienced formula was adopted to calculate the distance of the flying pieces. The calculating values of the distances of flying pieces are not identical with the practice results. The problems concerning the design way of flying distance of pieces are researched in the paper.

Jan 1, 1994

By Mike McGill, Stephen Chung, Dale S. Preece

Cast blasting can be designed to utilize explosive energy effectively and economically for coal mining operations to remove overburden material. The more overburden removed by explosives, the less blasted material there is left to be transported with mechanical equipment, such as draglines and trucks. In order to optimize the percentage of rock that is cast, a higher powder factor than normal is required plus an initiation technique designed to produce a much greater degree of horizontal muck movement. This is a significant change from normal blasting practice where fine fragmentation and sufficient muck movement were the prime requirements to permit efficient excavation.

Jan 1, 1994

By Robert E. Miller

Mass blasting of open stopes and pillars is a normal operating practice at Isa Mine. Three main parameters are used to classify the types of mass blasts. These are type of explosive used, blasthole diameter and system of initiation. Both electric and non-electric initiating systems are currently employed. The advantages gained by large firings are many. More efficient utilization of manpower, due to the concentrated and continuous charging, is achieved. There is no requirement for men to re-enter areas where localised ground conditions may have deteriorated and exposure of ringfirers to stope voids is reduced.

Jan 1, 1980

By Shijie Qu, Paul N. Worsey

Pre-splitting has become widely adopted for the formation and protection of final surface rock excavation profiles in both large scale civil construction and highway rock cuts. Jointing has been shown to affect the success of pre-splitting and the smoothness of the resulting profile, however, only closed joints have been investigated. Frequently jointing that is closed at depth is open at and near the surface due to weathering, reduced stresses and ground water percolation. In many instances, problems are associated with surface rock layers whereas at depth these problems are either reduced or do not exist.

Jan 1, 1987

By S Burchell

During the past few years, high-speed cameras, laser surveying equipment and photogrammetry have become standard tools for recording blast geometry and results. While laser profiling yields accurate 3-D measurements, most cameras capture only two-dimensional images. Attempts to extract 3-D information from photographs have been unsatisfactory. Recent advances in electronic imaging and computer programming have made it possible to develop a 3-D computer based analysis system which can capture and measure 3-D images quickly and accurately. This paper describes the technology to create 3-D images and to analyze blast geometry before, during and after the blast.

Jan 1, 1992