Search Documents

By Fearnside W. G.

Further discussion at the Midland Institute of Mining, Civil, and Mechanical Engineers' general meeting held in Leeds, March 21st, 1916, with T. Beach, vice-president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1915, vol. L, p. 573 and discussion vol. L., p. 109 and 608, comprised a brief written contribution by Faulds A.

Dec 1, 1916

By W. Doherty, P. C. Lightfoot, V. A. Fedorenko, N. S. Gorbachev, V. I. Kunilov, A. J. Naldrett, Z. Johan

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. A model is presented which regards the Lower Talnakh- and Talnakh-type intrusions as part of the plumbing system for the overlying lavas. As magma ascended along the Noril'sk-Kharayelakh fault it was forced to spread out within sedimentary strata immediately beneath the obstruction of the accumulated volcanic sequence. Here it was severely depleted in chalcophile elements by sulphides, which were then trapped by their high density and remained behind in the main arteries to form the central, elongated zone of maximum thickness. Subsequent magma also lost Ni, Cu and PGE to the sulphides as it flowed through. The Lower Talnakh-type intrusions represent part of the plumbing system that became blocked at an early stage, before the influx of much mokulaevsky-type magma rich in chalcophile elements. The model accounts for the high metal content of the ores in comparison with the size of their associated intrusions, the extensive metamorphic aureoles, the chalcophile depletion of some overlying volcanic suites, the presence of the ore in near-surface intrusions rather than deep magma chambers, and the sulphur isotopic composition of the ore

Apr 1, 1995

By P. Seppanen

Cemented fill was first introduced at the Keretti mine in 1952, but entailed high cement costs, the need for stope preparation, slimes handling, clean-up and maintenance, increased mine dewatering, segregation of fill and long setting times. In the 1970s research began into the use of iron blast-furnace slag as a binding agent and by 1989 Pyhasalmi, Vihanti, Keretti, Vammala and Enonkoski had saved US $11 000 000 by using slag binders instead of cement. Viscaria in Sweden and Tara in Ireland also use slag as 90-100% of total binder, although their backfilling methods vary. The main area of interest in slag research is determining the activation methods for initiating the binding reactions; it is also important to achieve other characteristics such as resistance to corrosion by sulphuric ion. New backfilling techniques developed during the 1980s included the use of high-density cemented tailings fill at Vammala and porous cemented rockfill at Enonkoski and Viscaria. Future developments focus on concepts such as integration of mining and milling with backfilling and the achievement of total underground disposal of wastes

Dec 1, 1995

By Briggs H.

Initial discussion of the paper presented at the Mining Institute of Scotland's general meeting held in Edinburgh, 12 February 1916, with D.W. Mowat, president, in the chair, included comments by Masterton J. (HM Inspector of Mines) and Sim J., and the author's reply

Dec 1, 1916

By A. L. W. Lips, T. J. R. Barclay, E. Rothery, S. H. White

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994 (originally entitled: The Broken Hill base metal deposit - a tectonically transported and modified basinal deposit within the Proterozoic Willyama fold and thrust belt). A regional structural study was undertaken which incorporated the role of shears. Their positions were identified from earlier mapping, from regional aeromagnetic data and by additional field work. Kinematic studies determined movement histories and petrological studies of the fault rocks formed within the shears identified the relationship between the movements and regional metamorphism. It was found that the shears formed a part of an earlier, major thrust event with transport from NW to SE and a later, minor one in the reverse direction. Neither had any significant effect on the mineralisation apart from local displacement, but the shuffling of the basin stratigraphy adds to the difficulty of recognising the original volcanic and sedimentary protoliths of the metamorphosed sequence. The mineralisation at Broken Hill mine is confined to a single recognisable thrust slice within a shear corridor. It is stratabound with locally transgressive remobilisation due to the high-temperature thrusting and some metasomatic alteration as a result of the retrograde shearing. This variation accounts for the different genetic models applied to the deposits in the past

Jun 17, 1905

By Ruddle R. W.

Although copper has been smelted for many years, relatively small attempt has been made in the past to examine the fundamental physical chemistry of the processes involved. Therefore, technological developments apart, slow progress has been made with the development of improved or new principles of smelting. The methods at present in use in the majority of the world’s smelters are essentially those employed at the beginning of the present century; it is significant that many of the textbooks on copper smelting, written some 50 years ago, are still regarded as standard works. The book is divided into seven chapters. In the first the fundamentals of modern smelting processes are briefly outlined for easy understanding of the subsequent sections, while the next two chapters are confined to the more theoretical aspects of the constitution of mattes and slags. Some problems of considerable practical importance are discussed in the remaining four chapters; these are (1) magnetite formation, (2) copper losses during smelting, (3) the recovery of sulphur from the smokes produced during smelting, and (4) the elimination of impurities. A collection of thermodynamic data relevant to copper pyrometallurgy is presented in an appendix, and, for the convenience of readers not well acquainted with thermodynamics, a brief explanation of the thermodynamic terms and methods employed is given in a second appendix

Jan 1, 1953

By C G. Wall, T S. Daltaban

Three quarters of recent increases in world oil reserve estimates since 1990 have been attributed lo ‘better reservoir management' rather than to new discoveries. For the United Kingdom Continental Shelf (IJKCS), the Department of Trade and Industry (DTI) has on 2.2 bn barrels of extra oil protection through effective reservoir management of existing producing reservoirs. Past practise has been to manage petroleum exploitation on a departmental basis, with exploration assessing and ranking prospects, reservoir engineering assessing development plans and production facilities implementing plans. Any reservations necessary might involve restarting the project evaluation from scratch. Current practice is to manage an operation through asset management teams involving all disciplines. It is hoped that this approach will not only eliminate fruitless directions of effort, but the quality of work in each discipline will benefit from interaction. That is, the result of a team effort is greater than the sum of individual efforts. To date, this is most apparent with the interaction between geology, reservoir geophysics and reservoir engineering through reservoir characterization. This is the current area of greatest effort, with improved geophysical technology and computer power leading to more and more detailed and complex simulation models. The equally important interaction of reservoir engineering and production and facilities engineering applied to fields in decline has not yet achieved the prominence that it deserves. Establishing priorities in reservoir management requires the very critical evaluation of the relative value of objectives. The fact that something can be done (3-D seismic, 4-D seismic, multilateral wells, or three phase multi-layer well test analyses etc) is not a good reason for doing it. Reservoir management should he a study of value added versus cost for any activity possible or proposed. Both in the areas of reservoir data acquisition and of assessing opportunities in the period of production decline, it is likely that expert systems will need to be developed with the associated base of experience, understanding and know ledge. A n other area for the future is the elusive target of ‘enhanced ’ oil recovery, as distinct from ‘improved’ oil recovery. The most likely route forward here is the incessant scrutiny of reservoir regions and units within fields for their suitability for pilot schemes for advanced recovery techniques implemented at a favourable time. Finally, the reduction of costs, the maintenance of low. but viable rates of production and the threat of abandonment costs will increase reserves. An increase which may have appeared insignificant in the past is now more valuable.

Jan 11, 1996

By Gibson J.

The writer hopes to prove that the economical tram is of even greater importance than, say, the economical engine, and as no difficult and involved calculations are required, and all the governing facts are simple and well known, the former is more easily attainable than the latter. In the first section of this paper the factors that determine the size and the construction of the tram are examined; whilst in the second section the road on which it runs is dealt with

Dec 1, 1916

By J. J. Mackay

The Parliamentary Under-Secretary of State at the UK's Department of Transport introduced the symposium, approved its emphasis on environmental planning and the mitigation of environmental impact, discussed the publicity resulting from the recent opening of the Channel Tunnel as well as the role of private financing, and pointed out the leading role played by the Department of Transport in the introduction of the New Austrian Tunnelling Method to projects such as the Jubilee Line extension and the Heathrow Express (an editor's footnote, however, mentions with regret the Heathrow subsidence that occurred just before the journal went to print)

Jun 16, 1905

By M. Schwartz

Hosting copper, gold, oil and liquefied natural gas, the country is an interesting target for miners. However, remote locations in inhospitable, unusual and difficult terrain cause problems. The government has worked to create a Sovereign Wealth Fund to manage government surpluses from minerals and energy but PNG scores very low among many criteria, including land dispute resolution, as revealed by the 2014 Canadian Fraser Institute in its survey of senior mining personnel.

May 1, 2015

By Mohammed Ali Shah, Martin Waller

The mining industry depends to a large extent on the availability of high performance equipment. For drilling this means a requirement for well engineered, reliable machines with mechanised handling and widespread utilisation of automatic control. Such machines enable performance optimisation of drilling operations and integration into a high productivity mining system. A review is presented of the current status of drilling technology as applied to the mining and minerals industry. This covers developments in: drill bit materials and design; drilling techniques; machine design; mechanisation; automation; and drilling control. It also covers the ways in which current and future mining methods and practices will influence the applications and demands placed on drilling activities. The probable impact of current research on the industry is discussed.

Jan 12, 1992

By J. A. Franklin, E. Broch, G. Walton

To make the best use of rock core, the mechanical character of the rock should be evaluated concurrently with conventional geological observations. The advent of simple techniques, such as the point load 'nutcracker' test, makes field logging of mechanical properties competitive with sampling and testing in the laboratory

Dec 1, 1971

By C. A. Pickles

Mixtures of silver chloride and copper chloride are produced during gold refining by the Miller process. A study was carried out into the reduction with iron of a synthetic Miller chloride containing 13.64 mass% Ag and 2.42 mass% Cu. The effects of smelting temperature and time and of additions of iron and borax were investigated. The results were interpreted in terms of metal recovery and quality. Temperature did not have a significant effect on metal recovery above the melting point of the metal product. Borax additions reduced vapour losses and improved metal recovery. With excess iron it was possible to achieve silver recoveries of about 100% and copper recoveries of about 70%. The metal product contained on average 76.1 mass% Ag, 7.5 mass% Cu and 12.8 mass% Fe.

Jan 4, 1993

Discussion of papers with authors' written replies and closing remarks.

Jan 1, 1947

By NA NA

Reports of discussion at sessions held in Keyworth, UK, on 22-23 April 1992.

Jan 12, 1992

By C. C. Harris

The use of Alyavdin's equation Y(x,t) = 1-e(-bt) for describing the effect of grinding time on size distribution is discussed. The equation transforms into linear form by expressing it as log-log reciprocal (1 - Y) versus log t. For plotting, specially divided grids are available; Rosin-Rammler or Weibull charts may be used. The data of Herbst and Fuerstenau are especially useful for illustrating the Alyavdin-Weibull chart in two applications: (1) presenting data (which are relatively unaffected by experimental scatter) and comparing them with theoretical predictions, and (2) as a test for the zero-order kinetics production hypothesis. The chart based on the Alyavdin-Weibull equation is suggested as a useful aid in the analysis of kinetic data (/ versus f), though not as a procedure in its own right. Proposed applications are (1) displaying data with excellent clarity, since it avoids the kind of congestion inherent in some other plotting methods, and (2) as a test for assumed kinetic relationships. Sometimes, equation 1 describes the data quite closely, and in these cases the parameter values appear to be related to certain operating conditions.

Dec 1, 1971

Further discussion at the Mniing Institute of Scotland's annual general meeting held in Glasgow, 8th April 1916, of the paper published in Trans. I.Min.E. vol li, 1916, p.169-186 with discussion p.187-188, included oral and written contributions by McLaren R. and Waddell H.

Dec 1, 1916

By C. E. Dunn

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Evidence is accumulating that reconnaissance-level biogeochemical sampling can provide valuable insight into the chemistry of the substrate. Problems such as seasonal variations in plant chemistry and the lack of a universal biogeochemical sample medium may be circumvented by adopting normalising procedures. The planet can be divided into a few climatic zones, each of which is characterised by one or two common plant genera. If it can be demonstrated that the chemical differences between certain species of a single genus are small - as is suggested by studies of boreal forests - it would seem feasible to apply biogeochemistry as a low-density geochemical mapping tool. The technique could prove particularly useful for assessing the substrate chemistry of areas of dense forest, rugged terrain and difficult access by employing airborne sampling of trees from helicopters

Jul 1, 1991

By A. Hemami

In order to automate the operation of mechanical loaders it is essential to have a knowledge of the forces that act on the bucket and of the trajectory that the bucket should follow. A trajectory for the cutting edge of a bucket is derived from studies of the forces acting during the scooping phase. The proposed trajectory has a minimum energy consumption and is simple to automate. It is determined initially by setting to zero certain components of the resistive forces to the bucket motion which would otherwise result in unnecessary work and consequent energy wastage. The method for finding the appropriate trajectory is discussed on the basis of the properties of the material to be loaded and the loader size.

Jan 4, 1993

By G. Richards

Application of the Internet of Things (IoT) technologies - the interconnection of uniquely identifiable embedded computing devices within the existing internet infrastructure - to the mining industry is discussed. IoT technologies are aimed at making projects safer, better optimised and more economic and are applicable to current or new underground or open-pit mines, regardless of size. Two examples are presented of successful implementation of IoT technologies, the Chelopech gold, copper and silver mine in Bulgaria, where production has increased from 500 000 to 2 000 000 tonnes/y and communication costs have been reduced by US $2 500 000 over 2 y, and the Pilbara project in Western Australia, where remotely controlled wirelessly connected autonomous trucks have covered ca. 3 000 000 miles and hauled almost 250 000 000 t of ore since 2008

Apr 1, 2015