Search Documents

By Mark Viduetsky, Dmitry Tropnikov, Victor Maltsev, Victor Sokolov, Alexander Purgin, Andrey Panshin, Alexander Bondarev, Pavel Kozlov, Igor Garifulin

"CFM pneumatic flotation machines were developed by the Institute of Materials Science and Metallurgy, UrFU, and designed to concentrate a wide range of ores and man-made materials. A key principle of work is pulp preparation for flotation owing to its saturation with finely dispersed air bubbles in ejectors. CFM plants, their advantages over domestic and foreign prototypes are described. CFM pneumatic machine commercialization resulted in: - machines demonstrated high floatation efficiency for concentration of rebellious pyrrhotite-bearing copper and zink by simultaneous floatation of copper and zinc minerals and depressing pyrrhotite. CFM- 1400M introduction allowed simplifying and optimizing the flow chart and increase extraction of copper - by 5.4%, zinc - by 9.5% and improve the quality of copper (3% Cu) and zinc (1.5% Zn) concentrates. - due to copper pyrite concentration by using CFM 1400M overall copper recovery was increased by 1.5 %, and the content of copper in concentrates - by1%. According to the results of pilot runs, the use of CFM flotation for zinc cakes concentration strongly intensifies the process of cleaning water-soluble metal compounds and, thereby, increases the efficiency of flotation concentration and subsequent milling. CFM machines showed higher specific capacity (three or four times higher) (both for feed material and froth product). Specifically, CFM froth product has higher content of useful elements (silver by 0.014 % abs. zinc by 0.31% abs.) and better extraction (silver by 6.08% abs., zinc by 0.31% abs., and sulfide sulfur by 13.7 %). Sulfide sulfur content of CFM product chamber as compared to mechanical flotation machines is two times lower (0.48 vs. 0.95 %)."

Jan 1, 2014

By Robert Snow, Shibo Zheng, Wenyi Song, Xiaoqing Ma, Patrick Zhang

Numerous phosphate mineral depressants have been reported in the literature for use during anionic flotation of dolomite from carbonate fluorapatite in slightly acid circuits. In one part of this research, laboratory flotation experiments were conducted to compare the effectiveness of phosphate depressants to process ground, deslimed high-MgO Florida phosphate pebbles. Ten potential phosphate depressants were evaluated during laboratory anionic flotation of dolomite from phosphate in a slightly acid circuit using a sulfonated oleic acid soap plus oil as the dolomite collector. Eight of the depressants have been used by various investigators with foreign and domestic carbonate-phosphate ores. Four of the depressants were found to be reasonably effective during the current flotation study, namely: sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP), tetrasodium pyrophosphate (TSPP) and diphosphonic acid (DPA). Without depressants, the sulfonate collector required to produce cell underflow phosphate products containing <0.80% MgO and MgO/ P2O5 ratio <.033 was 1.13 kg/ton of flotation feed at a flotation pH range = 5.5-6.0. Using this collector level with 0.91 - 1.36 kg/ton of feed of STPP, SHMP or TSPP yielded phosphate products analyzing 0.73-0.92% MgO and MgO/ P2O5 ratios = .027-.034 at 90.0-96.8% P2O5 recovery. Similar grade phosphate products were obtained using DPA as the phosphate depressant at 84.1-87.5% P2O5 recovery. When no depressant was used, a similar grade phosphate product was obtained at only 65.9% P2O5 recovery. Another part of the research aimed at reducing MgO content in the final concentrate from Florida phosphate plants by conducting dolomite flotation on the final concentrate. Numerous phosphate depressants were tested for this purpose, including acidic, neutral and alkaline reagents. The most effective phosphate depressant was found to be phosphoric acid, giving both high grade and recovery.

Jan 1, 2014

By Ata Akcil, Z. B. Karshigina, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva

Phosphorus slag is one of the most large-tonnage of yellow phosphorus production waste, which for decades stored in the slag disposal, by polluting the environment and creating environmental problems in the regions. Phosphorus slags from the processing of Karatau phosphorites are a very promising source of raw materials not only for silicon compounds but also rare earth metals (REM). Among the REM, yttrium, neodymium, europium and lutetium predominate, which are relevant to high-tech industries. The report presents technological scheme of complex processing of slags of phosphoric production with obtaining of REM concentrate and precipitated silicon dioxide ("white soot"). The regime parameters of the main operations of the technology are determined: I stage- leaching of slag with nitric acid solution; extraction of the REM-containing solution with tributyl phosphate and stripping of the REM with water; settling of solution of salts of oxalic acid, calcining the precipitate to obtain a concentrate S REM oxides and II stage of leaching silicon cake to obtain "white soot". Recovery of S REM from slags of phosphoric production on various redistribution has made, %: leaching – 95.0; extraction - 90.2; extraction on the average ~ 93.2; the production of a concentrate of REM oxide is 93.9. A concentrate containing 17.3 % of REM oxides was obtained. According to X-ray analysis it contains the following phases: calcium oxide, portlandite2, gadolinium oxide and yttrium, gadolinium oxide, gadolinium oxide and cerium, neodymium oxide, neodymium oxide and cerium. Thus, the concentrate can serve as a raw material for the production of individual rare-earth metals like gadolinium, cerium, yttrium and neodymium. After performing the II stage of leaching siliceous cake with nitric acid the samples of "white soot" were obtained. Its chemical composition corresponds to the state standard and has a specific surface area equal to 180 - 200 m2/g. The technology has been tested in a large-scale laboratory scale and will solve the problem of complex processing of phosphorus raw materials and import substitution in Kazakhstan. The end-to-end recovery of S REM oxides and silicon into concentrate and product from their initial content in slags is ~ 75.0 and 98.0 %, respectively.

Jan 1, 2018

By Yang Xiao, Zhang Yimin, Bao Shenxu, Liu Chun

Stone coal is a unique vanadium-bearing resource in China. Many techniques, such as salt roasting-water leaching, blank roasting-acid leaching, direct acid leaching etc. have been developed for vanadium extraction from stone coal. The vanadium leaching rate can reach 74.9% for stone coal from Jiangxi, but only about 27% of vanadium is leached for Hubei ore by applying salt roasting-water leaching technique. This paper investigats the vanadium occurrence in stone coal by microscope observation and electron probe, and compares the minerals components of stone coal from Jiangxi and Hubei. Although most vanadium exist as an isomorphism by replacing Al(III) from dioctahedral structure in mica group minerals in stone coal from two regions, the free vanadium is remarkably abundant in Jiangxi stone coal than in Hubei stone coal, which results the fact that vandium is relatively readily extracted from former. Moreover, the content of calcite in Hubei stone coal is much higher than that in Jiangxi stone coal. Calcium can react with V2O5 to form water insoluble calcium vanadates during roasting and this may be the reasone why the water leaching rate of vanadium is low for Hubei ore. Acid leaching is more beneficial to the vanadium leaching but other extra methods, such as adding aid-leaching agent and/or increasing acid concentration is need for the ore where vanadium is embeded firmly. This study can effectively guide the selection of vanadium extraction techniques for stone coal from different regions.

Jan 1, 2014

By Arkady Senchenko, Andrey Vasiliev, Alexander Aksenov, Metodi Zlatev

"This paper considers the issue of treating argillaceous oxidized ores with low gold grade (around 1.0 g/t). These ores according to their gold recovery level can be treated by heap leaching and agitation cyanide leaching, but low gold grade makes this treatment uneconomic. Heap leaching of argillaceous ores requires high consumption of binding agent for pelletizing to create suitable hydro-physical properties of material, which leads to increasing process cost and makes the material treatment unprofitable. Agitation cyanide leaching of this ore requires grinding processes; these expenses would not be paid back by the amount of gold recovered. Considering the above, poor argillaceous oxidized ores are recommended to be treated according to a combined technology including fractionation of ore, heap leaching of coarse fraction and agitation leaching of argillaceous fraction. Complex approach application allows one to avoid expenses incurred for material grinding and high consumption of binding agent for pelletizing. The success of this technology implementation will firstly depend on the quality of material fractionation, therefore the section of disintegration and division of ore into different components will be the most important part of flowsheet development for gold production. When disintegrating minerals at positive temperatures both standard (mechanical disintegration - scrubbers) and innovative (hydraulic method of disintegration - HydroClean units) equipment is applicable. HydroClean units are characterized by lower energy and water consumption. In a number of cases it is required to treat frozen ores. When treating frozen material standard approaches to disintegration are not reasonable due to their low efficiency. In order to treat frozen material a two stage disintegration flowsheet with screening after each stage is recommended. The first stage is recommended to be performed in a scrubber, the second - in a HydroClean unit. This technological flowsheet will provide high and steady values for ore separation into fractions at low energy consumption for disintegration."

Jan 1, 2014

By Miguel Becerra, Daniel Jordán, Jorge Soto, Luis Torres

"Most SAG grinding operations currently use ball sizes between 5.5 and 6 inch maximum size. However, in most cases the use of this ball sizes hasn’t been justified by a phenomenological analysis of the real effect on the grinding process, but rather by trial and error. The analysis of the influence of ball sizes in SAG grinding hasn’t been developed in detail by considering the effect on process parameters inside the mill, grinding efficiency or internal classification. Historically a conventional grinding reference has been made on the empirical procedure developed by Azzaroni (1980). Further to Azzaroni’s methodology, Sepulveda (Sepúlveda, 2007) developed the SPEC methodology, incorporating the ball size effect on the grinding efficiency parameters using a population balance model included on Molycop tools spreadsheets.This paper demonstrates a detailed analysis at pilot scale of the ball size employed in SAG grinding and scaling that exists between the different levels. This analysis includes assessing the effect of balls sizes on parameters associated with grinding efficiency and its effect on the total fill level, product size distribution and specific energy consumption, among others. In a complementary way it develops a technical - economical evaluation from industrial data comparing two different ball sizes and its effect on the grinding process analysed integrally."

Jan 1, 2014

By E. V. Zelinskaya, A. E. Burdonov

"In the raw aluminum production processon electrolyzers with self-baking anodes, during technological operations, flow-regulated treatment and adjustment of the electrolyte chemical composition produced by diesel and floor-rail technology, alumina and fluoride salts are spilled through the ventilation grilles of the electrolysis body aeration channels, leakage in the equipment, machinery and motorized machinery construction elements. As a result of this, a part of the bus station and the level of ± 0 (the basement room with supporting curbstones and columns, on which electrolyzers are installed) are covered with technological raw material. This leads to an increase in the conductor (bus) resistance, contact connections deterioration, cell insulation failure and raw materials loss. For example, at the enterprise ""Rusal-Bratsk"", as a result of the activity, up to 420 tons per month of alumina-containing wastes that are unfit for use in the electrolysis process are formed due to the alumina substantial contamination with salts of iron and silicon, which significantly reduces the technical and economic parameters of the electrolysis process. The main scientific problem is the processing (cleaning) of alumina-containing waste having a complex mineralogical composition of the material, its contrast and structure, from oxides of iron and silicon, using ""dry"" separation methods. In the performing the work process, qualitative indicators of the influence of external factors (air humidity, precipitation, sunlight, temperature difference) on the physicochemical processes components interaction during the raw materials storage are established. On the basis of laboratory tests, it is established that alumina-containing raw materials can be separated and photometric and gravitational separation methods used. A mathematical model of the motion of particles of primary and prepared alumina-containing raw materials in a cascade-gravity classifier was developed. The criteria and factors characterizing the alumina-containing material, as well as influencing and determining the maximum material enrichment, are established."

Jan 1, 2018

By U. A. Peuker

"Steam Pressure Filtration (SPF) is a modified cake filtration process and is characterized by both washing and excellent de-watering of the filter cake. Compared to conventional gas differential pressure filtration, the filter cake is treated with saturated or superheated steam replacing pressurized air. Invented in the early last century, Steam Pressure Filtration has reached technical maturity in the 1990ies for inorganic particle systems, fine chemicals and coal. Especially the de-watering performance for fine particles systems below 50 µm make Steam Pressure Filtration an excellent option for the processing of fine tailings streams, to produce a stable material, which can be described by the methods of solids mechanics instead of paste rheology. The washing, which is due to the condensing steam, is able to reduce the ion load of the solid. This additional effect is able to generate a dry tailings material, which shows a reduced leaching potential of mobile ions, which originally derive from the process water. INTRODUCTION Steam Pressure Filtration is a process concept especially of hyperbaric filtration, which started its market entry in the 1990ies (Bott 1996, Bott 2002). Even though there have been many attempts to apply steam on filters before, the success story began with the combination of hyperbaric filtration and steam application and the technical solution to limit the steam treatment to a defined zone on the filter. This resulted from the scientific findings that steam mainly enhances the de-watering during the mechanical filtration (Gerl 1999). There are no or minor positive effects of steam application to a filtration process during cake filtration and after the steam breakthrough has occurred. Furthermore that time a sufficient control technology to regulate the steam consumption as well as suitable filter cloths became available. There is a growing need for de-watering technology in the mining industry, not only for the concentrate but also for the tailings streams. Several reasons argue against the established solution of damping the tails as suspension or paste into tailings ponds. There are ecological, political, societal and economic reasons, which question the tailings ponds more and more. Due to the increasing costs in the building and monitoring of tailings dams, which contain the tailing ponds, the concept of dry stocking using filtration technology comes into the game (Jansson 2016). Dry stocking converts the tailings stream form the suspension or paste state, into a material, which can be stockpiled. The latter typically is a moist flowable disperse particle system. The conversion involves a de-watering step, in which different types of filter equipment can be used, e.g. filter presses, membrane filter presses, automatic press filters or hyperbaric filters. For coarse products also vacuum filter can be applied. Due to its excellent de-watering performance and the easy scale-up properties Steam Pressure Filtration is further option for dry tailings stacking."

Jan 1, 2018

By Y. G. Seredkin, A. A. Vasiliev, A. Y. Senchenko, A. V. Aksenov

"The valuable materials resulting from the processing of gold-bearing ores are often refractory to direct gold recovery through cyanidation. There are multiple methods for chemical liberation of gold prior to cyanidation such as pressure and biological oxidation as well as atmospheric oxidation which is typically used in combination with physical activation of material by ultrafine grinding such as the Albion ProcessTM. This paper will examine the data from process testworks carried out to estimate the efficiency of the Albion Process™ for the oxidation of materials with a wide composition range prior to cyanidation. The data will be compared to that obtained by direct cyanidation of the feed (without oxidation) and from the testing of pressure oxidation on the feed prior to cyanidation. Albion Process™ tests were conducted in Institute TOMS with participation of Glencore Technology Pty Ltd (Australia). Refractory concentrates obtained from the ores of several Russian and CIS deposits were used as feed for the testing. These concentrates were also subjected to a material composition study and testing using conventional recovery methods. The resulted test data make it possible to perform an integrated assessment of process properties for materials with different compositions, compare performance of various process flowsheets for the materials under study, and conclude on efficiency of Albion Process™ application for gold recovery from refractory materials different in their composition.INTRODUCTION It is often the case that gold ore concentrates are refractory to gold recovery by direct cyanidation. This refractory nature is as a rule attributable to fine gold dissemination in minerals, most often in pyrite and other sulphides, as well as to the increased amount of components impeding cyanide leaching of gold due to cyanide consumption and reducing process conditions. The refractoriness of the concentrates results in low gold recovery values when conventional cyanidation technology is used. In this context, various additional processes are applied to breakdown such refractory sulphide concentrates, i.e. mechanical breakdown (fine and ultrafine grinding), chemical breakdown (atmospheric oxidation, e.g. Leachox, acid-oxygen oxidation, pressure oxidation – POX, bacterial oxidation – BIOX), and thermochemical breakdown (various roasting methods). Such breakdown processes allow for increase in recovery of finely disseminated gold during the downstream cyanidation, however, their application is cost-intensive and does not always ensure economic benefit."

Jan 1, 2018

By Barun Gorain, Aparup Chattopadhyay

"Many double refractory gold deposits are characterized by the dominance of ""invisible gold"" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulfides and other phases. These deposits are mainly composed of silicates and carbonates with moderate clay and mica content and with minor amount of sulfides and organic carbonaceous matters. The presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in leach circuits. Characterization of carbonaceous matters, commonly known as TCM and quantification of gold associated within these carbonaceous matters along with different sulfide and oxide phases is highly complex and challenging. Studies were initiated on various complex ore deposits and also on samples representing various process streams. This paper presents the development of a systematic approach to gold deportment studies using state-of-the-art mineralogy characterization techniques for quantification of invisible and visible metal contents in various species. The relevance of this mineralogy characterization to metallurgy will also be discussed in this paper."

Jan 1, 2014

By Y. Posedko Eugene, S. S. Gudkov, Yu. E. Emelyanov, A. V. Bogorodsky, A. V. Boldyrev, S. V. Balikov

"The article presents the results of precious metals leaching using halogen solvents and their precipitation on a sorbent in the process of pressure oxidation. A technology of pressure oxidation – carbon-in-leach treatment (POX-CIL) of refractory sulphide gold-bearing flotation concentrates with the addition of a halogen solvent and a sorbent was developed based on the laboratory studies and pilot plant tests. The technology involves the following steps: oxidation of a flotation concentrate; precious metals dissolution and recovery on a sorbent; precious metals elution; electrolysis of eluates; smelting of cathode precipitates with producing Dore beads. This approach ensures oxidation at least 98% of sulphides and gold of more than 95%. The POX-CIL process have the following patents: a patent of the Eurasian Patent Organization No.017438 “A method of processing materials containing precious metals and sulphides” and a patent of the Russian Federation No.2625146 “A method of precious metals recovery from refractory sulphide gold-bearing materials”.INTRODUCTION Gold-bearing ores are classified as readily amenable to cyanidation, or non-refractory, and not readily amenable to cyanidation, or refractory [1]. Special attention should be given to the three most common technological types of gold-bearing ore materials, according to the Irgiredmet’s classification: pyrite-arsenopyrite ores with finely disseminated gold locked in sulphides (physical depression of gold in cyanidation process); cupriferous gold-bearing ores, when cyanidation comes along with chemical depression of gold by mineral compounds (cyanisides); carbonaceous ores showing higher sorption activity to precious metals dissolved in cyanide. Direct cyanidation of refractory sulphide gold-bearing materials does not provide high recovery of precious metals. There are the following methods of refractory gold-bearing ores and concentrates preparation to subsequent gold recovery: roasting, fine grinding, bacterial and pressure oxidation (POX) [2]. Existing POX-cyanidation flowsheets involve high costs due to a large amount of process operations and using expensive and environmentally hazardous sodium cyanide."

Jan 1, 2018

By M. Z. He

Attractive particle interactions which underpin the sliming of gangue mineral particles onto valuable mineral phases are encountered in a number of flotation circuits. Sliming leads to poor flotation recovery of the valuable minerals and high recovery of the gangue particles in the concentrate. To mitigate sliming, low molecular weight poly-electrolytes are commonly used as dispersants during pulp conditioning prior to flotation separation of the valuable and gangue mineral phases. In the present work, the sliming mechanism of sericite onto chalcocite and the influence of interfacial chemistry and two anionic copolymer dispersants (carboxylate substituted polyacrylamide, polymer Cyquest 3223 and sulfonate substituted polymaleic acid, polymer P80) on the sliming interactions were probed in the pH range 5~9. It was shown that the sliming occurred under solution conditions where both chalcocite and sericite particles were negatively charged, as evidenced by their apparent particle zeta potentials. The suspension pH had a profound effect on sliming process as the extent was markedly greater at lower than higher pH. The sliming was found to be due to the chalcocite dissolution, Cu (I) release and oxidation to Cu (II), followed by hydrolysis and specific adsorption, leading to sericite particle surface charge reversal and the formation of electropositive sites on chalcocite surface in the pH range 5~9. Addition of polymer Cyquest 3223 or P80 not only increased the magnitude of zeta potentials of both sericite and chalcocite particles but also reduced the formation of Cu (II) ions and complexes, which mitigated the sliming behaviour. The adsorption of polymer Cyquest 3223 or P80 at 3 g polymer / kg solid or more had a significant impact on the zeta potentials of both sericite and chalcocite particles. Sericite-chalcocite particulate adsorption studies showed that sliming was completely suppressed via an electro-steric repulsion mechanism resulting from anionic polymeric dispersant adsorption at dosages > 3 g polymer / kg solid.

Jan 1, 2014

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

"Research at Delft University aims to develop systems for automatic inspection and sorting of bulk solids which can be applied in the mineral processing and recycling industry. A recent development includes an automatic sorter based on airport X-ray inspection technology. It is designed for continuous inspection and sorting of 5 - 150 mm solids and has as objective a cost effective and high capacity on-line inspection and sorting.Dual energy X-ray transmission imaging provides instantaneous data about particle dimensions and the atomic number distribution. The system provides particle thickness and average atomic number on a pixel level at scanning speeds between 250 and 500 lines / second. With existing X-ray components inspection speeds between 0.5 and 2 m/s at approximately 1-meter inspection width and between 1.5*1.5 and 5*5 mm2 sensor resolution can be achieved.Imaging algorithms that were developed by Delft University for applications in recycling, waste cleaning and other applications acquire shape, size distribution and composition data. Currently on-line processing of a product at a rate of around 200 particles per second is possible using a standard PC. Experiments with a demonstration X-ray unit indicated good potential for various applications in solids processing. They include continuous inspection of organic content, sulphur, chlorine, ash, and metal distribution. It is applicable for coal cleaning, ore sorting, industrial minerals, and various applications within waste cleaning and recycling. Dual energy X-ray transmission fundamentals and recent progress in system development and applications are presented."

Jan 1, 2003

By I. Ngoma, Marijke Fagan, Susan Harrison, Rebecca Chiume

"Heap bioleaching is an unsaturated hydrometallurgical extraction process which is commonly applied to the recovery of copper from low grade sulfide ores as well as for preparatory treatment of gold ores. The leaching reactions occur in the liquid phase, catalysed by iron and/or sulfur oxidising micro-organisms. Contact of the mineral grains with the leaching solution is consequently essential for metal recovery. Additionally, the liquid is responsible for the transport of the liberated metal out of the heap under gravitation-driven flow. However, the highly inhomogeneous structure of the heaps coupled with low irrigation rates cause the flow to vary between being gravitationally and capillary dominated, resulting in non-uniform wetting of the ore. In this study a 132 kg agglomerated ore ‘slice’ is used to examine the effect of liquid distribution on microbial colonisation and mineral recovery in a long term bioleach (> 500 days) when irrigation from a single drip emitter source is employed. The novel setup enabled sample collection from ports positioned along the length and height of the ore bed, so that 2D maps of the degree of wetting and microbial colonisation could be generated at different times in the leach. Lateral movement of the liquid increased with bed depth; the majority of flow was below the irrigation point while the top corner of the bed that was not irrigated remained the driest region of the heap throughout the experiment duration. The lowest cell numbers were also recorded in the driest regions. Specifically, cell numbers in the top corner of the bed, 400mm from the irrigation point, remained at undetectable levels until the 283rd day measurement, in line with typical heap operation durations. This indicates that slow colonisation of the heap in the regions between irrigation points may be a significant issue in heap optimisation."

Jan 1, 2014

By F. v. d. Meer, G. Kretschmar, T. Mütze, T. Leißner

"Dynamic air classifiers separate particles in a gas flow due to different particle trajectories utilizing differences in the settling velocity of particles as characteristic property for separation. The present contribution takes a close look at the separation of heterogeneous mixtures, in which valuables and gangue minerals show significant differences in density. The focus was on a moist iron ore sample, which was characterized in terms of mineralogy, grain size distribution, and particle size distribution. The material was classified at a cut size of 45 µm and at feed moistures between 0 and 6 wt.-%. Additionally to standard characterization techniques, the moisture of both products was measured as well as the yield of fines as product fraction in a corresponding processing plant. In addition, an automated mineral liberation analysis (MLA) provided information of the enrichment and segregation of individual mineral phases in the products. The MLA of the classification products reveals a selective comminution of the mineral phases and especially on overmilling of the valuables. For the first time, the separation of individual mineral phases has been assessed and compared to the classic assessment of classification processes by means of particle size analyses. KEYWORDS Dynamic classifier, segregation, MLA, selective comminution INTRODUCTION Dynamic air classifiers separate particles in a gas flow due to the different trajectories of the particles. The result of such a separation process depends on the gas throughput of the classifier, the dimensions, design and rotational speed of the deflector wheel, as well as the state of dispersion and thus the geometry of as well as the turbulence and interparticle interactions in the separation zone. Air classification of moist feed materials can be divided into several sub-process (Leschonski, 1977; Mütze et al., 2016): - dosage of the feed material, - dispersing the solid feed material into a gas stream, - feeding the dispersed material into the classification zone by pneumatic conveying, - drying of moist particles during pneumatic conveying, - separation of coarse and fine particles, and - separation of fine particles from gas."

Jan 1, 2018

By T. Inoue, K. Okaya

"Movement of mill charge in the centrifugal mill is essentially different from that in the vibration mill with circular path despite the apparently similar mode in the motion of mill body. As proved e.g. in [11], this results in substantial advantage regarding the comminution intensity of the centrifugal mill over the conventional vibration mill accounting approximately to one order of magnitude.Back in 1983, Bradley et al. presented a model of the centrifugal mill based on the kinetics of the mill charge by regarding it as a lumped mass. On the other hand, numerical modeling by ‘discrete element method (DEM)’ enabled us to observe the movement of each ball in the centrifugal mill with an extremely minute time intervals (Inoue et al., XX IMPC in 1997). The former approach rendered simple, even though approximate, expression of the mill behavior, while the latter method was advantageous in describing the behavior of the mill in terms of individual events taking place in the mill body, even though the result did not reduce to a simple expression. The characteristics of the centrifugal mill described by both these approaches proved to be in a degree of agreement. Thus, the kinetic approach was capable of presenting the overall view of the mill, while the DEM model was informative of the details that could not be depicted well enough by the simple math expressions."

Jan 1, 2003

By M. Ghiani, R. Peretti, S. di Giovanni, G. Zonnedda, A. Serci, A. Zucca

"Beneficiation of the epithermal gold mineralizations associated with an extensive alteration zone in the Serrenti-Furtei region on the island of Sardinia, is proving a complex issue. Experimental investigations have in fact demonstrated that while the ores contained in the upper parts of the deposit are amenable to conventional cyanidation, the gold contained in the refractory ores in the lower portions needs to be recovered by means of flotation, combined with leaching where necessary.The results of commercial heap leaching, carbon-in-leach (CIL) processing and flotation, designed on the basis of the experimental findings and applied to the oxidized portions and transition zones of the deep sulphide mineralizations, confirmed the expectations emerging from the laboratory tests."

Jan 1, 2003

By Susanna A. C. Stadler, Chris Aldrich, Jacques J. Eksteen

Slag foaming occurs in several pyrometallurgical processes. These processes include steelmaking in basic oxygen steelmaking furnaces and electric arc furnaces as well as various non-ferrous operations like sulphide smelting/converting and base metal slag cleaning. Although slag foaming in steelmaking processes has been extensively researched, little attention has been given to slag foaming in non-ferrous operations. Slag foaming phenomena are complex because often the system consists of three or more phases. With this in mind, factors previously identified as influencing slag foaming were investigated. These include the slag basicity, physical properties of the slag, namely viscosity, surface tension and density, the formation of particles due to undercooling of the slag and the FexO concentration in the slag. The effect of increasing FexO concentration was found to decrease the foam index due to lower viscosities, but higher surface tension depression appears to have led to increased foam index values at high FexO concentrations. The foaming index decreases with increasing basicity, until precipitation of solids occurs. After this point, the foaming index was found to increase with increasing basicity due to increased solids precipitation. In general, increasing amounts of slag-wettable solids led to higher foam indices, but the precise nature of the effect on slag foaming was dependant on the nature of the solid precipitate.

Jan 1, 2003

By D. Steele, B. Ndlovu

"Adequate characterisation of clays is becoming increasingly important as operating mines move into areas of more complex ores. The processing therefore needs better mineralogical characterisation to identify problematic ores for better planning before issues arise. While a number of instrumental mineral characterisation methods are available, X-ray Diffraction (XRD) is widely recognised as perhaps the best technique for the identification and quantification of minerals, particularly clays. When an appropriate sequential and systematic sample preparation and treatment protocol is employed with instrumental XRD analysis individual clays can be uniquely identified, and the proportions of interstratified clays can also be quantified. The effect of sample preparation on the XRD analysis and identification of clays was investigated in this study. The results showed that sample preparation protocol is indeed critical to accurately analysis and characterisation of clays. For example, both dry grinding and micronizing affected the degree of crystallinity of kaolinite leading to the formation of reactive surfaces or changes in the physicochemical behavior. It was also found that the apparent degree of preferred orientation in platy minerals correlates directly with the amount of force/pressure applied during the preparation of backfilled powder samples. This work showed that manual preparation can produce highly variable peak intensities especially with minerals that show any preferred orientation. KEYWORDS Clay; XRD; kaolinite INTRODUCTION Clays are important in our life and they have numerous applications in modern world from cosmetics to environmental remediation. Therefore, clays have been extensively investigated for many years. Adequate characterisation of clays is becoming increasingly important as the mineral processing industry faces more complex mineralogy with the need for better mineralogical characterisation to identify problematic ores and plan accordingly. In most studies, X-ray diffraction (XRD) method has shown the unique capability to characterise mineralogy, especially for the fine grained size materials. The XRD technique is particularly diagnostic for clays. It is known that under ideal conditions, the peak intensities of an XRD diffractogram are proportional to the concentrations of individual minerals present in the sample. Hence, the qualitative mineralogical data obtained from XRD can be quantified, using either the internal or external standard methods. However, it is also known that clays are particularly sensitive to the influences of sample preparation method due to their physical characteristics (e.g. fine grain size, morphology, relative physical softness, crystallinity, thermal sensitivity) that could be destroyed by inappropriate preparation prior to the analysis. Thermal and mechanical treatment and grinding of clays can change their crystalline structure, and consequently, their characterisation results by XRD analysis. The behaviour of clays in grinding has been widely studied, especially for kaolinite (Miller and Oulton, 1970, Milocevic et al., 1992, Tomasevic-Canovic et al., 1992). With prolonged grinding time, the crystallinity of the clays can decrease (Filipovic-Petrovic et al., 2002). It has been shown that grinding may gradually cause the loss of hydroxyl ions of kaolinite (Gonzalez Garcia et al., 1991)."

Jan 1, 2018

By Kevin Davey, Liza Forbes, Leanne Smith

Given the global scarcity and value of potable water, interest in the use of water of lower quality in mineral processing has grown significantly in recent years. Previous laboratory batch flotation tests conducted at CSIRO have shown that chalcopyrite floats strongly without collector in distilled water and that the collectorless flotability of chalcopyrite is unaffected by the use of brackish water, sea water or hypersaline water. In contrast, bornite is moderately flotable without collector in distilled water but all three lower-quality waters have a detrimental effect on the recovery of bornite. The depressant effect is so strong that the little recovery achieved in these waters was only slightly above what might have been expected from entrainment alone. This work has now been extended to another important copper sulfide mineral, chalcocite. In contrast to chalcopyrite and bornite, chalcocite does not exhibit collectorless flotability so the chalcocite tests in this study were performed in the presence of a standard collector (potassium ethyl xanthate). The results reveal that chalcocite is flotable with xanthate in distilled water but the lower-quality waters have a detrimental effect on the recovery of chalcocite. This effect is partly reversed by increase collector additions. Further tests were completed in order to investigate the effect of the different ions present in the saline waters on chalcocite flotation. Possible reasons for the observed differences are discussed in terms of the pulp chemistry of the system.

Jan 1, 2014