Search Documents

By Ulrich Von Stackelber

Deep sea mining of manganese nodules actually will have an environmental impact to the seafloor and to the water column. However, we are far from being able to predict the possible consequences. Therefore, in 1992 environmental studies were conducted with the R/V Sonne in a manganese nodule field of the Peru Basin. The bathymetry of the seafloor was mapped using the hydrosweep system and the distribution and type of sediments were investigated by the parasound system and by collecting surface samples and sediment cores. Deep towing of a side-scan sonar system revealed a Mn encrustation of sediments and a nodule coverage of variable density. Along the tracks of a photo sledge a great variability of bottom fauna and of bioturbation was observed. Bottom-mechanical investigations of surface-near sediments were completed on board. Additionally water samples were collected near the sea floor to determine character and amount of dissolved and suspended particles. Manganese nodules and crusts were collected at 80 locations. In many aspects the nodules differ from those of the Clarion-Clipperton Zone: Big cauliflower-shaped nodules with growth rates up to 160 mm/ Ma may reach a maximum size of 24 cm in diameter, maximum abundance may be 44 kg/m2, the mean size of buried nodules is greater than that of surface nodules. The reason for that difference is due to the relatively high bioproductivity in surface waters and to a Mn redox boundary in the sediment column 10 cm below the seafloor. Histograms of nodules showing the distribution of size and growth type clearly indicate that the growth history is different for basins, slopes and tops of seamounts and ridges. Nodules with diameters >7 cm show mainly diagenetic and to a minor degree hydrogenetic growth. Smaller nodules of the same assemblage are composed mainly of hydrogenetically grown Mn oxide. The optimum diagenetic growth occurs within the sediment immediately above the Mn redox boundary, a level which is not reached by the small nodules.

Jan 1, 1994

By R. D. Hamer

"The Atlantis II Deposit comprises metalliferous sediments (Zn+Cu+Ag+Au) accumulating in a composite, axial basin, 2,000m beneath the surface of the Red Sea. The basin contains warm, highly saline water. It is located approximately half way between Jeddah and Port Sudan within the Exclusive Economic zones of Saudi Arabia and Sudan. The Deposit was discovered in 1963 and evaluated by drilling in the 1970s and 1980s. This phase defined an initial resource of approximately 90Mt. More recent estimations have refined this figure to an Inferred Resource of approximately 80Mt (CIM compliant).The Mining Licence to develop and extract the Atlantis II Deep Deposit was granted to Manafai International Trade in 2010 by the joint Saudi-Sudanese Red Sea Commission. Manafai is poised to embark on a renewed phase of exploration and evaluation, including the completion of a Definitive Feasibility Study (DFS) and leading to the successful exploitation of the Deposit in a safe, environmentally sound, economically viable and socially responsible manner.The Deposit is forming in a complex basin adjacent the median rift, where sea floor spreading has operated during the last 5Ma. It is a Hydrothermal-sedimentary Deposit. The mineralised sedimentary rocks rest directly on sea floor basaltic rocks. They are produced by the exhalation of metal-rich, hydrothermal brines from fissures associated with the central rift and cross-cutting fracture zones. Up to 25m of metal-rich sediments have accumulated over an area exceeding 57km²."

Jan 1, 2017

By J. R. Woolsey

Research grants of The Marine Minerals Technology Center (MMTC) are directed toward development of the technology 'for exploration, mining, and processing of non-fuel mineral resources within the U.S. Exclusive Economic Zone. FY 1989-90 research grants are as follows: - Seafloor Gamma Measurement Data Collection System. - Free-Fall Seafloor Hard Substrate Corer. - Microtopography of Manganese Crust Deposits. - Cobalt Crust Continuum on Seamounts, EEZ, Hawaii. - Economics of Marine Polymetallic Sulfide Resources. - Graphite Furnace Atomic Absorption Spectrometer. - Depositional Models for Aggregate and Heavy Mineral Exploration. - Sand Resources of Heald and Sabine Banks, Texas. - Sources, Geometries, and Compositions of Heavy Mineral Placers. - Geostatistical Methods for Marine Placer Exploration. - Computer Aided Design for Communication and Strength Umbilicals.

Jan 1, 1989

By Campbell McKenzie

Substantial consideration has been given to the implications that the morphology of the Chatham Rise deposit will have on mining operations. The glacio-tectonic processes involved in the distribution of nodules on the rise has in several areas been quite significant. The recent cruises by Chatham Rock Phosphate Limited (CRPL) have collected data which has affirmed the assumptions previously made and catered for in historic resource estimations. The deformation and displacement of the phosphorite during glacial periods and the redistribution of the mobile sand during interglacial periods is interpreted to have produced a highly variable pattern of phosphorite concentration (kg phosphorite/m2) and coverage (% phosphorite/sample weight). The phosphorite resource probably has a significant spatial variability at a scale of tens of metres. Results of recent surveys show phosphorite-rich patches alternating with phosphorite-poor areas at distances of less than 20 m. The high spatial variability of the deposit has had a bearing on how historical information for the project has been regarded and integrated with the recent exploration approach and data collection process. This coupled with the proposed extraction tool has influenced the size, nature, extent and siting of the proposed mining blocks

Sep 14, 2011

By Tao Chunhui

The seabed deposits type and distribution are very complex at the hydrothermal field. In this paper, we provided an approach to study the seabed deposits classification at the Precious Stone Mountain hydrothermal field (PSMHF) using MultiBeam sonar data . The PSMHF was found in the Galapogas microplate at the Leg 3 of the Chinese COMRA 21st Cruise. Using this approach, the seabed deposits at the PSMHF are mainly classified into three types, which are rock, breccia and sediment, respectively. We can find the distribution of the three types of seabed deposits according to the sonar backscatter data. The rocks are mostly distributed around the hydrothermal vent. The breccia are located at the foot of the vent. Most sediments are distributed at the southwest to the vent due to bottom current. Combining with seabed video, TV-Grab sample and the backscatter data, we draw the map of the seabed deposits distribution at the PSMHF.

Sep 14, 2011

By Charles W. Finkl

Coastal and marine aggregate (sand and gravel) mining on US continental shelves is a major activity that supplies industrial and commercial demands for these raw materials. Because Pacific, Atlantic, and Gulf coasts contain significant shoreline segments that are in a critical state of erosion, sand-gravel and mixed sediment (sands with a high percentage of silt-plus-clay) deposits are mined in efforts to mitigate land loss. Sandy shores, and to a limited extent gravel coasts, erode by shoreline retreat due to relative sea-level rise and sediment starvation in littoral drift patterns. Mostly gravel shores occur in high latitudes and shorelines often advance seaward due to isostatic rebound following the LGM (Last Glacial Maximum 18,000 YBP). Sandy and fine-grained shores occurring in middle and low latitudes of the conterminous United States are problem coasts that require beach renourishment and reconstruction of barrier islands. Muddy coasts of the Mississippi Delta region are especially problematic because some islands are literally disappearing in response to subsidence. Replacement of sediments lost to the littoral drift system or returned to sedimentary sinks by drowning is thus a critical endeavor that involves annually dredging hundreds of millions of cubic meters of sediments from the continental shelf area. The types of shelf sediments that are amenable to marine mining techniques, their occurrence, and means of detection are highlighted in this paper. Minable Sediments on the Continental Shelf Wide varieties of sedimentary bodies that occur on the continental shelf are amenable to mining for beach renourishment and barrier island (beach-dune-marsh system) reconstruction. Relict terrestrial deposits make up a small but important proportion of shelf sediments that were deposited on coastal plains, now drowned by the post-glacial sea-level rise to form continental shelves. Examples of these deposits include drowned moraines, outwash plains, eskers, and kettles along the northern Atlantic coast in addition to siliciclastics along middle latitude Pacific, Atlantic, and Gulf coasts. Special cases include carbonate sequences along tropical costs of Florida and the muddy coasts of deltas, mostly in Louisiana. Specific types of minable deposits thus include shoreface attached sand sheets, dunes, and ridges in addition to offshore inter-reefal sands (between coral reefs in the Florida Reef Tract), bank deposits, and sand waves (ridges) that extend into US territorial waters. Nearshore siliciclastics include ebb-tidal deltas and bars. Drowned river valleys occur along all three US coasts and can be exploited for their fluvial sands if the covering mud sheets are thin.

Jan 1, 2005

By Satya Nandan

The International Seabed Authority is currently considering regulations for prospecting and exploration for polymetallic sulphides and cobalt rich crusts. The deposits of these two types of minerals are very different from polymetallic nodules for which the Authority has already adopted regulations in 2000. The presentation will discuss the nature of the deposits, the inadequacy of information and data concerning these deposits and their environment, as well as the problems of defining the method of allocation and the size of the areas to be licensed for exploration, and those to be retained for exploitation; the current status of the draft regulations being considered by the Council of the Authority.

Aug 24, 2006

By Natsumi Kamiya

The Metal Mining Agency of Japan (MMAJ) has started the project in the fiscal year of 1989 under the administration of the Ministry of International Trade and Industry '(MITI). The purpose of this study is to assess the impact on the ocean environment caused by manganese nodules mining. Summary of research and survey of MMAJ is as follows: 1. Evaluation of environment impact The aim of this study is to assess impact for ocean environment by manganese nodules mining. It is studied by using three-dimensional hydrodynamic prediction model and by carrying out cultural experiment of surface fauna with adding deepsea water and sediment. Development of hydrodynamic prediction model for discharged water at ocean surface has started in 1989. On board cultural experiment was carried out in the Japanese application area in the eastern Pacific in May 1991 and in May 1992.

Jan 1, 1993

By Audrey Boissier, Marie-Anne Camon, Cecile Cathalot, Yves Fouquet, Laurent Bignon, Arnaud Agranier, Ewan Pelleter, Sylvain Bermell, Florian Besson

INTRODUCTION In October 2014, on behalf of the French government, Ifremer, along with the International Seabed Authority (ISA), signed a contract to start a detailed exploration program for seafloor massive sulfide (SMS) deposits in the work plan located on the slow spreading Mid-Atlantic ridge (MAR). The contract has a fifteen-year lifetime and the related exploration program must include the outline of SMS deposits and a resource assessment, as well as detailed environmental base line studies in the contract area. The exploration for SMS deposits generally includes detection of hydrothermal plume anomalies, acquisition of surface and near-bottom geophysical data, sampling operations from the research vessel (e.g. dredges, cores), and dive operations. The environmental studies include, among others, short and long-term oceanographic measurements, water column studies, biodiversity evaluation close and far from SMS deposits, characterization of natural hydrothermal plumes and related sedimentation. The HERMINE research cruise held from March 13th to April 28th 2018 (R/V Pourquoi Pas?) was the first cruise dedicated to exploration of active and inactive SMS and to the quantification of natural chemical input to the water column. The HERMINE cruise strategy was built up around three main objectives: (i) regional exploration including the detection of plume anomalies and the research of SMS deposits, (ii) local exploration of a SMS district and (iii) integrated study of a natural hydrothermal plume. This 3-in-1 cruise required us to optimize the switch between dives and surface operations. Day-time was devoted to dive operations whereas night-time was mostly dedicated to CTD/Rosette operations. The Nautile HOV (Human Occupied Vehicle) was well suited to the working time schedule of the cruise because it was time efficient in shorter (i.e. < 10h) dives due to fast descent and ascent speed, fast submerged forward speed, high maneuverability and the ability to carry heavy science payload as well as large volume of samples. Regional Exploration The first seventeen days of the HERMINE cruise were devoted to regional exploration, i.e. the detection of new plume anomalies and the research of new sulfide mineralization in the French work plan (10 000 km2; 6 clusters).

Jan 1, 2018

An extensive ferromanganese nodule field south of New Zealand (Fig. 1) has existed beneath the flow of the Deep Western Boundary Current (DWBC) and Antarctic Circumpolar Current (ACC) for at least the past 15 m.y. West of 174°E, between 59°S and 48°S, the field is 300-500 km wide, but east of 174°E, where current flow impinges on the eastern slope of the Campbell Plateau, the field narrows from ca. 200 km at 55°S to ca. 120 km at 51°S. This narrowing coincides with deflection of current flow eastwards, and consequent reduction in bottom-current velocity and eddy kinetic energy. Based on sea floor photographs, dredge samples and 3.5 kHz profile data, six distinct seafloor substrates are delineated, forming broadly parallel zones eastwards from the lowermost Campbell Slope (Fig. 2).

Jan 1, 2003

By Cornel E. J. de Ronde

Brothers volcano (34°51.7?S, 179°03.6?E) is a large caldera volcano that forms part of the active Kermadec arc south of 32° S, NE of New Zealand. It is an elongate edifice striking NW-SE that is ~11-13 km long by 7-8 km across. The caldera has a basal diameter of 3-3.5 km and is surrounded by 350-450 m high walls with the floor 1,850 m deep. A volcanic cone of dacite composition rises 350 m from the caldera floor and partially coalesces with the southern caldera wall. Much of the caldera construction and the location of the hydrothermal vent sites are controlled by intersecting basement structures. Three hydrothermal sites have been recognized at Brothers; NW caldera, SE caldera and cone. Multiple hydrothermal plumes were mapped from the bottom of the caldera upwards to a depth of 900 m and originate from two of the sites; one on the NW caldera wall the other atop the cone. Analyses of these plumes show that the two vent sites are chemically distinct. The cone site itself hosts three distinct vent fields (summit, upper flank, NE flank) that in 1999 had plumes (mainly from the summit) containing relatively high concentrations of gas with a shift of -0.27 pH units (proxy for CO2) and H2S concentrations up to 4,250 nM, particulate Cu (PCu) of 3.4 nM, total dissolvable Fe (TDFe) of 4,720 nM, TDMn up to 260 nM and Fe/Mn values between 4.4 and 18.2. However, in 2002 plumes from the summit vent field had noticeably lower concentrations of PCu (0.3 nM), TDFe (175 nM), and Fe/Mn values of 0.8, although similar TDMn (220 nM) and shift in pH (-0.22) suggesting a state of flux for this site. By contrast, plumes originating from the NW caldera site have much less gas with a pH shift of -0.09 units and no detectable H2S, TDFe up to 955 nM, TDMn up to 150 nM, and Fe/Mn values of 6.4, and have not changed their composition over the same three year interval indicating a more chronic hydrothermal system. Plume d3He results show helium is decoupled from more near-surface vent fluid sources although a shift in R/Ra values from 6.1 ± 0.5 in 1999 for the combined vent sites to 7.2 ± 0.1 in 2002 indicates a less radiogenic input of helium over three years, suggestive of a greater magmatic input to the system.

Jan 1, 2004

By Georgy Cherkashov, Vladislav Kuznetsov

The presentation describes new data concerning the age of the Mid-Atlantic Ridge (MAR) hydrothermal fields. The collection of massive sulfides recovered from six hydrothermal fields has been dated using the 230Th/U method. The range of the data obtained is rather wide: from 2.2 up to 65.1 thousand years BP. Three stages of hydrothermal activity were detected for this 65 Kyr period of geological evolution: modern (0 -5), 20-25 and 58–65 thousand BP (Figure 1). This conclusion was confirmed by dating the associated metalliferous sediment layers which also indicate the hydrothermal events led to the formation of sulfide mineralization. There is a correlation between the age and size of massive sulfide deposits: older deposits are larger (Table 1). This and other applications of obtained data will be discussed in presentation.

Aug 24, 2006

By Graham Singleton

Around 235 million tonnes of marine aggregates have been dredged in the last decade from the UK continental shelf alone. The current distribution of marine aggregate production licence areas in North West Europe reflects the relationship between a variety of factors such as the natural distribution of deposits of sand and gravel, the demand for aggregates, the technical capabilities of the dredging fleet and environmental considerations. Whilst the sand and gravel deposits targeted by the marine aggregate industry are generally relict and therefore geographically fixed, the remaining factors have evolved over time and will continue to do so in future. Applications for new licences must not only reflect the current situation, but anticipate future trends. The main markets for marine aggregates are the construction industry, centred around the larger centres of population and coastal protection projects along the coastline of Europe. The aggregate industry as a whole does not create demand but simply meets it. Many factors influence the overall demand for aggregates and guidance exists for those in authority and industry who need to plan for the supply of aggregates. Adequate supplies should be maintained at the best balance of social, environmental and economic cost, whilst ensuring that extraction and development are consistent with the principles of sustainable development.

Jan 1, 2004

By Tetsuo Yamazaki

Manganese nodules, seafloor massive sulfides, and cobalt-rich manganese crusts in deep-sea areas have been considered as future metal sources (Mero, 1965; Halbach, 1982; Lenoble, 2000). Manganese nodules were the first recognized deep-sea mineral resource and many efforts concentrated on the R&D of mining systems (Welling, 1981; Herrouin et al., 1989; Yamada and Yamazaki, 1998) and assessment of environmental impacts (Burns et al., 1980; Foell et al., 1990; Yamazaki and Kajitani, 1999). No mining venture, however, has been active for this potential resource. The reason is that the rate of world economic growth has been slower than anticipated in 1960s. During the 10 year period of 1994-2003 (Fig. 1), on the other hand, there was about a 33% increase in the world copper demand. Of that increase, about 60% was consumed by China. Most of China?s increased copper demand took place over the final 4-5 years of that period. The growth is expected to continue for several years, and in 10 years or sooner the same situation is expected for India. Copper is the third metal in global demand, but its small abundance in the Earth?s crust is not well recognized (Table 1). From the production rate and the abundance, a copper shortage, or crisis, has a high probability than the other metals. Japan has no domestic copper resources and needs a counter measure for this potential coming copper shortage. Fortunately, Japan has a manganese nodule mining claim in the Clarion-Clipperton nodule field, Kuroko-type massive seafloor sulfide deposits in the Okinawa Trough and Izu-Ogasawara areas, and cobalt-rich manganese crusts around Okinotori-Shima and Marcus Islands. We need to re-evaluate their potential as copper resources and to realize their development.

Jan 1, 2005

By Hjalmar Thiel

Issues of deep-seabed mining are discussed since four decades and extensive efforts have been invested in oceanographic studies related to environmentally sound harvesting of polymetallic nodules. Because mining on the deep seafloor seems to range from large-scale, two-dimensional dredging or scooping up of the ore from the uppermost surface sediment layer to more localized drilling or deeper digging into a three-dimensional ore body, it appears to be justified to reconsider some concepts for environmental impact evaluation. Based on the experience gained during preceding years in environmental studies related to polymetallic nodule mining, some interrelated hypotheses and proposals will be presented. It is suggested that these proposals be considered in future plans for environmental impact evaluation and that observations on community re-establishment be conducted before massive sulphide mining or other ore extractions enter the commercial mining phase.

Aug 24, 2006

By Lénaick Menot, Anne-Sophie Alix, Charline Guérin, Sébastien Ybert, Ewan Pelleter, Florian Besson

Ifremer, on behalf of the French government, holds an Exploration Contract with the ISA for polymetallic nodules in the CCFZ. As part of its exploration activities, the NODULE (2015) cruise was conducted to acquire a 50 m resolution bathymetric coverage of the eastern sectors of the Contract. In 2017, Ifremer initiated an update of the Contract’s mineral resource estimate. Metal grades and nodule abundance were modelled using ordinary kriging. The inferred mineral resource is 436 Mt (wet) of polymetallic nodules at an average abundance of 10.7 kg/m² with a cut-off grade of 7 kg/m². Based on the geological data, seamounts, sedimentary basins and steep slopes contain no nodules. Technical studies of most of the contractors have determined that nodule collectors could not maneuver on slopes above 5 to 10°. Thus, Ifremer has selected a quite conservative slope threshold of 7 % (about 4°) and a backscatter threshold of -29.5 dB to delineate nodule-free areas. This has a significant impact on the resource estimate, as about 54 % of the eastern Contract areas are excluded. Near-seafloor high-resolution mapping and photographic transects, associated with finer-spaced box-core sampling could constitute a next step to better constrain the mineable areas and to get a higher level of confidence in the resource estimation.

Jan 1, 2018

By S. Jeffress Williams

Continental shelf margins are dynamic sedimentary environments that contain important benthic habitats and support many functions such as navigation, national defense, cables, pipelines, trawling, and oil and gas and mineral extraction. Coastal margins also contain resources such as sand and gravel aggregates, which are becoming increasingly important for beach nourishment to mitigate coastal erosion and enhance recreation and to restore degraded coastal ecosystems. Existing geologic maps of the seafloor and sub-bottom sedimentary character, morphology, texture, composition, and other seafloor properties are not available for some regions, are out of date and not inclusive of the massive data collected during the past several decades, and are not in GIS-based digital formats. New geologic maps, based on unified and integrated national digital datasets, showing the sedimentary character of continental margins are critical tools for both research to better understanding the geologic history and processes of continental margins as well as the distribution of habitats and resources and for managing coastal-marine resources. The majority of existing seafloor maps are decades old and do not include recent data from mapping surveys, seabed sampling and observation carried out by federal agencies, universities and industry. Because continental margins are increasingly important, comprehensive and integrated databases are needed to produce GIS-based digital maps displaying information such as seafloor geology, sediment character, texture and distribution. To meet the need for a unified database of seafloor sedimentary character, the USGS is conducting the Marine Aggregate Resources and Processes project, a national assessment of marine sand and gravel with federal, state, and academic partners.

Jan 1, 2004

By Robert M. Owen

Geochemical exploration for marine placers involves the acquisition, processing, and interpretation of geochemical data. Recent technological advances such as in-situ analysis systems and microcomputers have greatly improved our ability to acquire and process data, but their full benefits cannot be realized until we also develop improved methods for reducing and interpreting large amounts of raw geochemical data. Toward this end, our research has sought to identify existing and/or develop new geostatistical techniques for use in marine placer exploration. Each technique has been tested by evaluating its performance in the analysis of existing data sets. The data sets typically include the results of chemical analyses of suites of sediment samples collected from areas of known or suspected platinum and gold placers along the Bering Sea coast of Alaska. Results to date indicate that three geostatistical methods (subpopulation partitioning analysis, comparative factor analysis, and end-member compositional factor analysis) are useful in identifying elemental groups which can serve as "pathfinders" in the search for marine placers, and are also helpful in discerning the generic geochemical basis under lying observed statistical correlations between pathfinder elements and placer minerals. Existing methods of modelling sediment dispersal patterns have been examined with a view toward adapting them to the specific problem of understanding placer formation in

Jan 1, 1986

By Richard H. T. Garnett

Diamonds were discovered on the coast of Namibia in 1907 but it was not until 1962 that the first gems were produced from offshore by a barge employing an airlift. Geophysical surveys and a sampling program were initiated and an understanding of the diamond distribution was gained. Several vessels, some with multiple airlifts, were used until the early 1970&apos;s. Some spectacular production results were achieved, but generally the systems failed to retrieve the gravels efficiently from beneath the overburden and off the bedrock. Various companies continued working with mixed outcomes until the mid-1980&apos;s, when new regulations were enacted by the authorities. The local Southern sea conditions dictate the present mining methods which are now applied over several hundred kilometers of the west coast. In shallow waters divers operate from small vessels, suctioning the diamondiferous gravels to surface with gravel pumps. In water depths of up to 50 m airlifts of various designs continue to be utilized with recovery plants installed on the vessels. Beyond 100 m depths a remote controlled, tracked, vehicle is used, together with a large drill mounted on swell compensator. Each system is deployed from a separate ocean-going vessel. Production of diamonds from the offshore is rising rapidly, with expectations of further increases. The coastline is likely to be the scene of new developments in marine mining techniques.

Jan 1, 1992

By Henrik Schiellerup, Irene Zananiri, Johan Nyberg, Thomas Kuhn, Luis Somoza, Teresa Medialdea, Maria Judge, Pedro Ferreira, Gerry Stanley, Javier González

The GeoERA Co-Fund action is a joint contribution of 48 national and regional Geological Survey Organisations from 33 European countries “Establishing the European Geological Surveys Research Area to deliver a Geological Service for Europe (GeoERA)”. This is an ERA-NET action under Horizon 2020. The aim of GeoERA is to fund transnational projects contributing to the best use and management of the subsurface, addressing the following four themes: Geo Energy, Ground Water, Raw Materials and Information Platform. The European Commission recognises the significance of raw materials through its Raw Materials Initiative (RMI), the European Innovation Platform on Raw Materials (EIP-RM) and Horizon 2020 funding, specifically through Societal Challenge 5 – Climate Action, Environment, Resource Efficiency and Raw Materials. The GeoERA Raw Materials Theme will contribute to research and innovative developments for minerals inventory, minerals yearbook, exploration, mapping, modelling, metallogeny and critical raw materials in the pan-European framework including the sea. A major element in Europe’s long term economic strategy is to ensure security of supply for strategic and critical metals as part of the Blue Growth Strategy developing sectors that have a high potential for sustainable jobs and growth as seabed mining. The project MINDeSEA results of the collaboration between eight GeoERA Partners and four Non-funded Organizations at various points of common interest for exploration and investigation on seafloor mineral deposits. The Geological Surveys of Spain, Germany, Greece, Ireland, Norway, Portugal, Sweden and Ukraine are organisations with responsibility for coastal, marine geological investigation and mineral resources studies and mapping in their respective countries. The Non-funded participants: the Instituto Português do Mar e da Atmosfera; the United States Geological Survey; the All-Russia Scientific Research Institute for Geology and Mineral Resources of the Ocean; and the Geosciences Institute, host important databases, they have an international reputation for excellence in both science and technology, and are internationally-known experts on seafloor mineralisation and hydrothermal systems. This project addresses an integrative metallogenetic study of principal types of seabed mineral resources (hydrothermal sulfides, ferromanganese crusts, phosphorites, marine placers and polymetallic nodules) in the European Seas. The work program includes all the regional seas around Europe comprising the Atlantic Ocean, the Mediterranean Sea, the Baltic Sea and the Black Sea (Fig. 1). The MINDeSEA working group has both knowledge of and expertise in such types of mineralisation, providing exploration results, sample repositories and databases to produce innovative contributions. The importance of submarine mineralisation systems is related to the abundance and exploitation-potential of

Jan 1, 2018