Search Documents

By Larsson Lars-Erik, Rani Isa, Martin Jönsson, Håkan Bredenberg, Mats Larsson

"IntroductionSteel Core Piles are used extensively in Scandinavian countries, where hard rock is found within reasonable depths. A steel core is cast into a drilled steel tube casing and a rock hole is extended below the casing. This pile type is considered a very reliable type of pile, and for urban environment it has several advantages compared to other types of piles. One critical phase of the installation is the drilling of the casing. Usually a DTH (Down The Hole) hammer is used. Drilling in fine grained soils, e g silt, below the ground water level, may give rise to an excessive volume of soil material flushed up from the point of the casing, resulting in unacceptable settlements around the pile installation area.Using a new method for drilling of the casings, the ELEMEX-method has proven to significantly reduce the risk for such problems. In the paper a case record from a ground improvement project in central Stockholm is described. Ground settlements around the drilling area were carefully monitored over a longer period. Both the new drilling method and the conventional DTH casing drilling method where used, so that the corresponding ground settlements could be compared. Settlement records and comments are included in the paper.The paper also gives a description of the project. The installation of new piles and foundation constructions cover a whole city block in Stockholm downtown. The reason for the replacement of the old, damaged wooden piles were due to their destruction caused by a long time lowering of the ground water table. The paper gives a description of the new drilling method as well as an overview of usual urban foundation issues and their solution in Sweden, Finland and Norway.Drilled Foundation MethodDrilled Foundation, using drilling methods originally developed for drilling of large diameter rock holes, is today a standard method for the installation of piles, tiebacks, drilled pile walls and other foundation components, especially in urban built up areas where other techniques as drop hammers, augers, vibratory hammers and other equipment fail to meet the requirement, se ref(1). Drilled foundation is for example used for"

Jan 1, 2014

By A. R. Dover

The Richmond-San Rafael Bridge is a 6.92 kilometer (4.3 mile) long major toll bridge span that crosses the northern San Francisco Bay in a highly seismically active region. Tutor-Saliba / Koch / Tidewater JV was contracted by Caltrans to conduct a comprehensive seismic retrofit. The JV provided geotechnical planning and quality control services as described herein, under normal oversight by Caltrans. Part of the robust foundation retrofit design included the installation of 26 new, large diameter piles, including eleven 3.81 m (12.5 ft) diameter, cast-in-drilled-hole (CIDH) marine piles that were drilled 9.15 m (30 ft) into the bedrock beneath the Bay, where the water depth ranged up to about 21.3 m (70 ft). These reinforced concrete-filled composite piles have a steel shell permanent casing from the bridge substructure pile cap through the water column and 30.5 to 39.6 meters (100 ft to 130 ft) of marine sediments to the top of rock. This paper discusses construction, inspection (ranging from the QA employed in the planning of the CIDH pile installation methods and equipment to the actual construction inspection required for the routine installation of the shafts), problems that were encountered during construction, and the solutions that were developed and implemented. Inspection, particularly with the usual difficulties in the marine environment, coupled with the difficult and complex bedrock conditions was particularly challenging, and ranged from non-destructive testing to "in-water, inshell" diver inspection. Similarly, the complexities of dealing with both the steel casing "riser" and the associated drilled shaft (rock socket) portion of these composite foundation elements created some unusual issues. The paper also presents important lessons learned from the project.

Jan 1, 2008

By D. G. Bishop

This paper is intended as a review and update of the use of Pressure Injected Footings as deep foundation units in North America. We will discuss various aspects of this pile and then discuss a particular project - the Mobile Alabama Convention Centre which is currently under construction. Pressure Injected Footing is a generic name used to describe a foundation unit that has been in use around the world for some 80 years. It has been used on all types of structures. It is an excellent pile in both compression and tension. It is particularly economic where a layer of granular soils can be found at relatively shallow depths. Other types of piles would penetrate these layers. Caissons are often difficult to construct in these soils because of their lack of cohesion and the often present water table. PIFs can density these shallow layers and carry relatively heavy building loads on them.

Jan 1, 1992

By A. K. C. Chan

Recent hotel investment projects in China often involve very tight programmes for design and construction. An example given in this paper involves a 24-storey reinforced concrete hotel tower with 460 bedrooms and a 3-level podium commercial complex. The building is supported by relatively widely spaced columns and shear walls below which 88 number large diameter piers were excavated through fill, silty and bouldery clay on to dolerite and slate at depths between 15 to 3 0m below ground level. Whereas much experience has been accumulated in Hong Kong, hand-excavated pier foundation was only adopted for the first time in Dalian. This paper describes and discusses the various factors influencing the choice of the type and design of the foundation system. The criteria for determining appropriate founding levels are then explained. During installation, revisions to the acceptance procedure were made to cater for local conditions. Emphasis is placed on the role of the geotechnical engineer in making on-site decisions during construction. The advantage of the foundation system in accommodating on-site changes resulting from local complex ground conditions is demonstrated. The pier foundations were successfully completed ahead of programme.

Jan 1, 2010

By Tracy Brettmann

The use of rock-socketed Augered Cast-In-Place (ACIP) piles is new to the Austin and central Texas region. This case history describes the design methodology, load test results, quality control procedures and the rate of production pile installation for the first large commercial project where ACIP piles were used in Austin. The piles were 24 inches in diameter and extended through about 45 ft of alluvial materials to be socketed 6 ft into limestone. A full-scale instrumented load test was performed on a test pile that was loaded to 452 tons and held for 24 hours. Telltales were installed in the middle and the tip of the test pile. As part of the overall quality control procedures, singlehole sonic integrity logging was performed on the production piles to verify structural integrity during pile installation. During pile production, an average of 14 piles per day were installed, which is approximately seven times faster than the original design that consisted of drilled shaft foundations.

Jan 1, 1998

By M. Hesham El Naggar, Yasser Abdelghany

"ABSTRACT: The axial and lateral monotonic and cyclic behavior of helical pile foundations was investigated and new innovative helical screw systems suitable for seismic loadings were developed and patented. More than one hundred full scale field load tests were conducted on instrumented helical screw piles installed in cohesive soil. The piles included: plain helical screw piles (P-HSP); grouted (G-HSPs); fiber reinforced polymer FRP-G-HSPs; and reinforced grouted RG-HSPs. The RG-HSP piles axial capacity was more than twice that for P-HSP, with minimal reduction after cyclic loading, and their lateral capacity was more than 3 times the P-HSPs capacity. A 3-D finite element model was established. The results of 3-D finite element modeling were used to establish the load transfer mechanism and a design methodology for the considered piles.INTRODUCTION AND LITERATURE REVIEWHelical (screw) anchors have been utilized in tension loading and have gained popularity for bearing load applications. Helical piles represent an overall cost effective alternative to conventional piles for new construction and repair applications. The helical piles speed and ease of installation, less noise during installation added advantage with regards to their efficiency and reliability for underpinning including re-support and reconstruction of distressed and damaged foundations for either stabilization or rehabilitation. The “square shaft” SS175 pile is a segmented deep foundation system with helical steel bearing plates (helices) welded to a central steel shaft. Load is transferred from the shaft to the surrounding soil through these bearing plates. Segments or sections are joined with bolted couplings. Practically installed depth is limited only by soil resistance and economics. A helical bearing plate or helix is one pitch of a screw thread. All helices regardless of their diameter have a standard 75 mm pitch (Figure.1). The performance of single helical anchors and group action were studied experimentally and theoretically by several researchers, the researches focuses on the installation torque and uplift resistance. Some researches focus on the load carrying capacity with little pile response to cyclic loading effects or to instrumented full scale field testing. Helical piles axial compressive or lateral loading still is not well characterized and needs more analyses and their seismic performance was not investigated. For such this research was initiated to investigate the helical piles monotonic and cyclic performances under axial and lateral loadings to consider their usage in different applications in seismic zones. Among the several researchers, Clemence (1983); Mooney et al. (1985) conducted field and laboratory testing; Hoyt (1989), Hoyt et al. (1995), and Ghaly and Clemence (1998) conducted theoretical and experimental testing, Puri and Vijay (1984), Huang et al. (1995), Perko (2000), and Pack (2000) conducted theoretical analyses. Rao and Prasad (1993), Prasad and Rao (1994), conducted experimental testing; Vickars and Clemence (2000) studied the performance of helical piles with grouted shafts."

Jan 1, 2014

By Mario Mauro

The article illustrates the Hydromill technology, as applied in urban sites, and its advantages in terms of quality of the end product, mitigation of the construction impact, and optimization of the logistics at the site. Also highlighted are the main features of the excavation equipment and slurry treatment plant. Two recent urban applications of this technology in Europe are briefly described, together with the forthcoming application to the Central Artery/Tunnel Project in Boston. Introduction The Hydromill technology has been used extensively in Europe in the last decade for slurry wall construction in urban environments. In Italy, this technology has been applied by Ing. Giovanni Rodio & C., Impresa Costruzioni Speciali S.p.A. in two large projects. The first project is the construction of Stations Darsena and San Giorgio of the first metro line in Genova. The second project is the "Cut-and Cover" tunnel for the railway link in Torino. Hydromill technology will be used for the construction of the Soldier Pile Tremie Concrete walls of the Boston Central Artery Tunnel Project, contract C14C2, Utility Relocation at Fulton Street.

Jan 1, 1994

By Walter Ensinger

Working safely means working cost-effectively. Every "dangerous occurrence" and - even more so - every industrial accident causes disruptions in the planned course of construction. Besides moral and legal obligations, economic aspects are therefore also factors motivating increased efforts towards optimal prevention: improvements in work safety and protection of health are wise investments! Ever since its earliest days, the European Federation of Foundation Contractors (EFFC) has made this subject one of its key objectives and therefore set up a Safety + Environmental Working Group, in which experts from the member organisations exchange national experience and develop proposals for "best practices". The paper presents current developments and results from the work of the S+E WG with particular reference to the project "Ideas for Safety Improvement".

Jan 1, 2006

By Thoedtida Thipparat

The diaphragm walls and barrettes are very important to the constructions of multi-storeyed buildings, elevated expressways, subway railway stations, etc. Uncertainties particularly increase in accordance with the construction progress. Overcoming uncertainties influences the construction goals including achievement of time. This paper is aimed at proposing an uncertainty assessment and delay evaluation model to assess uncertainties and evaluate delay resulting from those uncertainties. Neurofuzzy systems (NFSs) for assessing uncertainties and evaluating delays are developed. Artificial neural networks (ANNs) have ability for learning from the past data and generalizing outputs for the next applications which are provided for fuzzy logic systems (FLSs). FLSs have ability for exploiting the tolerance of imprecision and uncertainty. FLSs provide the reasoning to the ANNs. Uncertainties affecting each operation were assessed and delays were evaluated by following steps of the proposed model. The uncertainty assessment and delay evaluation approach was applied to a diaphragm wall and barrette construction to demonstrate how to implement the proposed model. The results of the test case application were used for handling delay at all operations regarding the corresponding uncertainties.

Jan 1, 2006

By E. R. Wang

This paper outlines the engineering properties of shallow soil in Shanghai area. The main points that should be paid attention to during deep foundation investigation, and general conditions of experimental soil engineering are discribed.

Jan 1, 2010

By K. Englehardt

J BERESFORD introduced the subject of the paper which is the use of polymeric slurries to support the sides of diaphragm wall and bored pile excavations during construction. In the opinion of the authors the use of a suitable polymeric fluid offers financial and technical advantages compared with traditional bentonite based slurries. Under quiescent conditions a support slurry must have the following properties. - sufficient viscosity to support the sides of the excavation, to prevent infiltration into soils and to hold loose soil particles in suspension. - when agitated it should thin quickly to assist pumping transfer and cleaning and allow free passage of the grab or drill. - viscosity should be low enough during concreting to facilitate placement but high enough to prevent contamination of the concrete.

Jan 1, 1991

By Y. G. Qin

In this article an experimental study of axial bearing capacity of half-closed steel pipe pile installed at BKSH dock is presented. In comparison with open and closed end piles, half-closed end pile is considered to have high bearing capacity and good penetration, that is, it not only has a capacity as twice as the same size open end steel pipe pile, but also has blow counts as half as the same size closed end steel pipe pile. It is economic to use half-closed end pile in soft ground without a deep deposit of thick stiff clay. This article also describes a large scale model pile test and preliminarily analyses mechanism of improvement of bearing capacity of half-closed end pile with emphasis on effect of squeezed soil on side friction; an empirical approach is presented in which side friction is related to density of squeezed soil and which is useful for reasonably chosing side friction of different types of piles in design of foundarion.

Jan 1, 2010

By Christian Divis

[ ]

Jan 1, 2002

By Zhou Lu-Jian

The Port of Shekou is situated at Shenzhen Bay on the east bank of Lingding Ocean. Its coastline is about 6 km long and the water depth near the shore is Favourable. Across the bay is the ' New Territories " of Hong Kong. The port is at a distance of 22-23 seamilesaway from center of Hong Kong and 80 seamiles to Huangpu Harbour of Guangzhou, its highway links with Shen-Guang Highay. Since 19 79 China Merchants Group of the Transportation Department, began to set up Shekou Industrial Zone, the port has been developing and flouri­shing in business. With 15 large or small berths in all, the present portline is 2600 m, and the annual cargo throughout is over 3,000,000 tons and the annual passenger traffic is about 2,000,000 persons. Equalling a medium-scale seaport, it has been officially approved as an oceangoing transit port by the ministry of Transportation. The construction of Shekou port is chara-terized by the self-collected funds and the short construction period. In view of this, the optional plan of the port structure must serve the requirements of simplicity in struture, economy in mate­rial and speed in construction. That accounts for the most application of the sheet piling type to the port in Shekou. Once the project was approved, the cons­truction started. Only within an average period of 7-8 months, a deep water pier was completed and put into operation, which covered series of processes from exploration, designing, tender for con­struction to completion.

Jan 1, 1991

By Theodore R. Maynard

The history of foundation engineering in Chicago is a tale of innovation, made necessary in order to keep pace with structural technology which allowed taller buildings with heavier bearing loads, to accommodate a non-conducive geologic setting. The geology as it relates to foundation construction and underground construction in general is briefly described. A chronology of important events from the birth of Chicago to the present is presented. The impact of various construction techniques which were either initiated or refined to allow the growth of Chicago are discussed. Introduction The growth of Chicago resulting in today's high-rise high-density population center can be looked upon as a history of modern underground construction. The two major reasons which explain this are 1) It grew up during a period of rapid development in the Industrial Revolution and 2) Its natural geological setting needed a great deal of innovation for continuing growth.

Jan 1, 1991

By Edward J. McNamara

People in the real estate industry are fond of saying that the three most important features of a piece of property are, in order, location, location, and location. This is perhaps the reason that the owners of a well known high-end restaurant chain chose to spend $15 million dollars to renovate 5000 square feet of basement in a 22-story commercial building in the heart of New York City's Time Square. The goal was to create a music club with a stage area and dance floor with a mezzanine level surrounding the dance floor. In order to create the 50' x 40' dance floor and 20' x 40' stage area, 3 concrete columns were removed. New transfer girders were used to transfer the loads of these columns to new steel columns. For the mezzanine, nine columns had to be underpinned. All work continued while the restaurants, shops and offices above carried on business as usual. This paper details some of the means and methods utilized as well as the challenges faced by Underpinning & Foundation Constructors, Inc. in underpinning the columns and installing the new transfer steel.

Jan 1, 2000

By Kenneth A. Pidgeon

This paper presents a case history on mitigating vibration problems associated with the installation of steel sheetpiles. The project in-cludes installation of steel sheetpiles for a utility trench within 40 feet (12.2 meters) of a very sensitive manufacturing facility. Numerous production line quality control instruments and manufacturing processes within the manufacturing facility are extremely sensitive to vibrations. To minimize the impact to the owner, we specified that the contractor perform a vibration study using different types of pile hammers. The results and conclusions of the vibration study are presented in this paper.

Jan 1, 1995

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

Since the 1989 Loma Prieta Earthquake in the San Francisco Bay Area, the California Department of Transportation (CALTRANS) has accelerated seismic upgrading of their bridges. Many structures can be improved with the simple addition of hinge seat restrainers. Others require modification of column bents and superstructure to column connections. Often, footing retrofits are necessary, which require the addition of tension/compression elements (compression piling and tiedowns anchors) to resist overturning moments substantially larger than those originally used for footing design. These footing retrofits may include doweled reinforced concrete footing extensions or new pile caps which transmit forces to either driven steel or drilled concrete piles. In some cases, installation of these traditional piling elements is expensive, impractical or impossible due to: low overhead clearance, ground obstructions, high water table, noise or vibration sensitivity, or the inability to laterally expand the existing plan dimensions of the footing. In the latter case, one practical option is to attach small diameter drilled and grouted tension/compression piling elements (Pin Piles) to the existing footing. The footing may be strengthened with dowels and added concrete thickness or there may be a reduced shear span due to the installation of larger or jacketed columns. A reduction of elements is available with a Pin Pile alternative, particularly when the selection of traditional standard piles is governed by the reduced tension/uplift capacity available from the traditional elements, since Pin Piles exhibit superior uplift performance.

Jan 1, 1993

By Michael W. Neill, O&apos

Drilling slurry has become an effective aid to the construction of drilled shafts in caving and/or waterbearing soils. Historically, drilling slurry made of bentonitic clay and water was first used in the US in water well drilling as early as 1889. In coastal Texas drilled shaft contractors began using slurry, often made of on-site clay mixed with potable water, in the years following World War II, on a relatively routine basis. This type of slurry was used to "process" boreholes, in which the borehole was drilled "in the dry" until water or unstable soil was encountered, after which water and on-site clay were introduced into the borehole and mixed in place with the auger or other drilling tool. Drilling then continued under a slurry consisting of the uncontrolled mixture of clay and water until the excavation had reached a relatively impermeable and cohesive material. At this point, a steel casing was dropped into the hole and sealed into the lower stratum of impermeable geomaterial (soil or rock). The slurry inside the casing was bailed or pumped out, drilling continued to plan depth in the dry, a reinforcing cage was set in the partially cased borehole, concrete was placed and the casing was withdrawn. Some soil-slurry was undoubtedly trapped between the casing and the borehole wall, but the quality of that slurry was usually of no concern, because engineers of the period usually viewed drilled shafts as nothing more than deeply buried footings. Any unejected slurry would only serve to lower side shearing resistance, not yet considered in design, but would have no effect on end bearing. In the 1960 's the effectiveness of soil-slurry came into question because it was often ineffective in maintaining borehole stability at marginal drilling sites and because the economy of using shaft resistance, in addition to end

Jan 1, 1991