Search Documents

By Allen Cadden

The type of soil we had was a silty fine sand. It had been placed by hydraulic methods in 1904 so it was quite clean I would say less than 10% silt the rest of it was very loose sand. That I'm not certain, I've only done it on sandy soils but it would stand to reason that some sort of a number should apply because you are measuring the amount of work that you are doing to it so if the soil is fairly consistent over the site it should be able to generalize from there but I don't know for a fact that it works. Well, verifying to ourselves that this method actually worked because we weren't certain at first when we were doing it so then we would develop the numbers and then check the results.

Feb 10, 2003

"After the non-destructive testing is completed, the data must be compiled, evaluated, and interpreted. During this process, the data may indicate that there is an anomaly warranting further investigation, which may eventually be determined to be a flaw or defect. The definitions of an anomaly, flaw, and defect can be described as follows (after Amir, 2002):Anomaly - Any irregular feature identified in the NDT graphic results. An anomaly may be due to the testing instrumentation (such as noise), to the means used to perform the test (e.g. access tube debonding in CSL) or to the shaft itself. It is the responsibility of the NDT practitioner to gather and analyze all relevant data and try to resolve every anomaly before it is declared a flaw or defect.Flaw - Any deviation from the planned shape, size and/or material of the shaft.Defect - A flaw that, because of either size or location, may detract from the shaft’s intended performance or durability. The geotechnical engineer and the structural engineer are jointly responsible to decide which flaw comprises a defect.This section describes the process of evaluating the data, determining if an anomaly exists, and if so, deciding whether the anomaly is actually a flaw or a defect. If the anomaly is determined to be a defect, its effect on the performance of the shaft must be evaluated, and if necessary, the can be re-engineered, repaired, or replaced."

Jan 1, 2004

By John Erikson, Alan J. Lutenegger, Nicholas Williams

"In order to evaluate the level of disturbance produced in clays during installation, a series of single-helix and multi-helix anchors were installed at a test site consisting of a stiff overconsolidated clay crust overlying softer near normally consolidated clay. Field vane tests were then conducted over the top of the helical plates at various depths to determine the undrained shear strength after installation and were compared with undrained shear strength measured in adjacent undisturbed ground. The tests represent the first time that the degree of installation disturbance has been evaluated directly and show that even with perfect installation practice the clay is disturbed as a result of rotation of the helices during installation. The results show that the soil is not completely remolded but that the strength is below the peak undrained strength of the adjacent undisturbed ground. Measurement of the installation torque and the rate of advance are used to define an “Installation Disturbance Factor” which may help to evaluate the quality of the installation by the Contractor and degree of soil disturbance. INTRODUCTIONAn important consideration in the design of Helical Anchors is the degree of disturbance to the soil during installation. This may be especially important for saturated fine-grained soils where the disturbance from installation may produce a reduction of the undrained shear strength. Even though this was recognized as early as 1950 by Skempton, soil disturbance is often ignored by engineers using current design procedures. Field investigations were performed to obtain both directs and indirect evaluation of the degree of disturbance produced by the installation of single-helix and multi-helix anchors in clay and the influence of disturbance on behavior. The investigations involved measurement of torque and advance during installation, load tests performed to determine load-displacement behavior and ultimate capacity and field vane tests performed over the helical anchors to evaluate changes in undrained shear strength as compared to adjacent undisturbed ground. The characteristics of the site and details of the installation are presented. Results of the field vane tests are shown for a number of helical anchor installations and results of load tests are presented. The results indicate that a reduction should be made to the undisturbed undrained shear strength for design and that the reduction may be related to the Sensitivity of the clay and quality of installation."

Jan 1, 2017

By K. Rainer Massarsch

"Part 2 of 2 (Continued from Summer 2004 edition) By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenVibrations, which are caused by the installation of piles in dry or permeable soils, can cause settlements. The magnitude of settlements depends on several factors, such as soil type and stratification, ground water conditions (degree of saturation), pile type and method of pile installation (driving energy). A method of settlement prediction due to construction-induced vibrations has been presented by Massarsch (2000). However, in many cases, an engineering assessment must be made at an early stage of a project. The following simplified procedure can be used to estimate settlements in a homogeneous sand deposit adjacent to a single pile, Fig. 5. This approach is based on extensive experience from soil compaction projects. It is assumed that intense densification due to pile penetration occurs within a zone corresponding to three pile diameters. The volume reduction resulting from the propagating vibrations will cause settlements in a cone with an inclination 2V:1H, with the tip at a depth of 6 pile diameters. Thus the settlement trough will extend a distance of 3D+L/2 from the centre of the pile, with maximum settlements at the centre of the pile. Maximum settlements, Smaxand average settlements, Smax can be estimated using the following relationship, choosing an appropriate a value of the soil compression factor, from Table 2.The driving energy depends on the method of pile installation, soil stratification and the pile type. The displacement volume of the installed pile has been neglected. The simplified method is applicable for estimating settlements at the perimeter of a pile group. It should be noted that settlements also occur outside the assumed cone, but these are often negligible. The effect of incompressible layers should be taken into account by adjusting the effective pile length."

Jan 1, 2004

By Andres M. Baquerizo, Matthew E. Meyer, Carlos Ortiz

"The Metropolitan Miami development, a downtown mixed-use complex developed by Miami-based MDM Development Group, has weathered the economic downturn by adapting to the needs and pressures of the local market. The development (a.k.a. Met Miami) epitomizes the term “mixed-use urban development” with its combination of condominium ownership, rental apartments, hospitality, office and retail components within Miami’s urban core. Initially conceived and conceptualized in 2004, the development has gone through several concept changes. Today, the global USD $900 million development approaches completion.The foundation evaluation, design and construction for this development included the use of innovative and state-of-the-art augered-cast-in-place (ACIP) piles. The testing for these elements included (1) the first-ever, multi-level O-cell load test of an ACIP pile, (2) a world record 5,200 ton (46,261.5 kN) equivalent top load test of an ACIP pile, and (3) continued the advancement of the ACIP pile industry to include the deepest and largest diameter pile installation to date. Those dimensions were up to 36 in (914 mm) in diameter, and 120 ft (36.6 m) deep. The project showed ACIP piles were a proven alternative for structures exceeding 70 stories in South Florida.The development includes four parcels. Met 1 and Met 2 are completed, and the construction of the Met 3 development is just beginning, with completion expected in 2014. Once the Met 3 development is completed, the design and construction phases of the project will have spanned a decade. The Met Square portion of the development, which will be a retail and cinema component, is proposed for the parcel between Met 1 and Met 2."

Jan 1, 2012

By Torsten Wichtmann, Jan Macheck, Frederik Broz, Patrick Staubach, Hauke Zachert

The majority of heavy or strongly loaded structures, for instance high-rise buildings, large span bridges or gas storage tanks are founded on pile groups. However, current design codes and guidelines do not provide a standard procedure for their design under lateral dynamic and high-cyclic loading arising from e.g. wind, temperature or earthquake loads. To establish appropriate design strategies, a better understanding of the pile-soil, pile-pile and pile-cap interaction is required. This paper is focused on finite element backcalculations of centrifuge tests on single piles and pile groups subjected to up to 500 lateral load cycles. For the finite element simulations, a special calculation procedure is applied, combining two kinds of constitutive models, a conventional (Hypoplasticity with Intergranular Strain extension) and a special highcycle accumulation (HCA) model. The parameters of the constitutive models are calibrated based on static and cyclic laboratory tests on the sand used in the centrifuge tests. The performance of the applied numerical procedure is evaluated based on a detailed comparison of the simulation results with the measured data from the centrifuge tests. Overall the applicability of the used numerical strategy for simulating the behavior of pile groups subjected to high-cyclic loading is shown.

May 1, 2022

By Emre Biringen

Over the past decades, there has been an increasing recognition of the strategic use of pile-supported rafts in design of heavily-loaded structures to reduce total and differential settlements. However, such a hybrid foundation construction method has not been widely utilized in many countries, including the U.S., due to code limitations. In current practice, the foundation design is based on either (i) the bearing capacity of the raft supported by the subgrade soils, or (ii) solely the pile capacity. This paper addresses the potential use of such hybrid piled-raft systems, where the structural load is shared by both by the piles and the subgrade soils directly beneath the raft, in foundation design of power plant structures. The study assessed some of the characteristics of piled-raft behavior by undertaking three-dimensional finite element analyses of two raft sizes, and various pile layout patterns, including the rafts with piles distributed evenly and only in the central area of the raft. The computer software PLAXIS 3D with the Mohr-Coulomb constitutive soil model was used to facilitate the modeling of such cases. The results presented in this paper indicate how strategically locating the piles could reduce the differential and total settlements.

By Serhat Baycan, Mikias Yohannes

"Kuala Lumpur Karst is a complex limestone formation that is characterized by presence of cavities, solution channels, pinnacles and floaters. Basement excavations in such geological formations are usually challenging, mainly owing to the unpredictable rock head depths and potential for groundwater inflow. Any excavation support system should have adequate robustness and water tightness. Traditionally, Secant Bored Pile walls (SBP) with struts are the preferred option for karst ground. This paper discusses a cost effective and innovative alternative solution for a particular site – using Deep Soil Mixing (DSM) and using Contiguous Bored Piles (CBP) together with Ground Anchors (GA). The site, located around one of the busiest areas of Kuala Lumpur, is a 5,700 m2 commercial and residential development. A 16.0 m deep excavation was needed for four levels of basement and excavation support along the 275 m perimeter of the development. Within the site, the depth to rock head varied from 6 m to 19 m. The basis for each solution and conditions for its suitability are discussed in detail. Some design considerations and construction challenges are also presented. The performance of the two retention systems during excavation are presented, together with comparisons versus design predictions. Suggestions for future development are also given. Advantages of this approach compared to other traditional approaches are highlighted.1. INTRODUCTIONThe geology of Kuala Lumpur is among the most complicated and geotechnically challenging formations in South East Asia. The majority of the city falls into the Kuala Lumpur Limestone formation; which is a thick, highly-weathered and cavernous limestone. This formation is pure calcitic to dolomitic in composition, having infrequent schist and phyllite interbedding (Gobbett et al., 1973).The KL limestone has a highly karstic topography dotted with cavities, ravines, interconnected subterranean channels, pinnacles, overhangs, floaters and slump zones (Tan, 2006). This results in erratic bedrock profiles even within short distances. It is not uncommon to see a precipitous rock head incidence within short distances in the same site. In most parts of the City, the bedrock is typically encountered ranging from very shallow depths to about 30.0 m. The exception to this is at the heart of the City, where Kenny Hill formation prevails above the KL limestone. In such cases the limestone bedrock can be encountered much deeper. The erratic rock head profile and the highly karstic nature of the KL limestone makes it a geotechnical challenge requiring careful consideration of suitable engineering solutions.1.1 – Site DescriptionThe site, located in downtown Kuala Lumpur, is abutted by a busy street on the North. Before development, the site previously served as a car park. To the west an access road separates the site from an empty lot; while on the east, the lot is bounded by light weight residential and commercial buildings. On the south side, the site is bordered by a road that separates it from a prominent Shopping Mall in the City. A layout plan and an artist’s impression of the finished development is shown in Figure 1."

Jan 1, 1900

By Kaushik Mukherjee

"Malaysian offshore and surrounding region are favorable to the installation of driven piles. During the design phase, pile driveability analysis plays a major role in pile make-up design to suit and selection of the feasible hammer, besides defining acceptance criteria to ensure a certain level of confidence of its fitness for purpose. The accuracy level of driveability analyses depends substantially on the selection of its parameters that best represent the in-situ scenario. The most uncertain of the parameters are those related to the soil model. It is noted in various projects in the region, that the consideration of suitable soil resistance to driving, coupled with soil dynamic parameters, significantly affects driving sequence planning, design, material, hammer selection and most importantly pile acceptance criteria. This is particularly relevant for a region that contains predominantly clayey subsoil resulting in large diameter, long friction piles susceptible to driving disturbances and slow strength recovery. Various researchers suggested suitable dynamic parameters and soil resistance during driving calibrated to specific regions. Regional experience suggests a set of soil degradation and parameters to suit the different stages of driving which is corroborated by pile monitoring records during continuous and delayed driving scenarios. The most sensitive amongst all dynamic soil parameters is the skin damping in clay. Smith’s wave theory approach considers a conservative assumption in selecting the parameters in absence of site-specific data, while a different approach may be adopted based on consistency of the clay for a site where the geotechnical parameters are well defined. This paper summarizes some independent studies on the effects of variations in dynamic parameters and resistance at different stages of driving and suitability of choices of different pile make-up and hammers for an optimum design. Similar experiences, coupled with simulation studies and back-analyses of available driving records suggest a reasonable judgment for the region.INTRODUCTIONFixed structures are generally supported in the in-place condition on a pile foundation those may either be driven or drilled & grouted piles depending on the subsoil. The piles may be driven inside the jacket legs or drilled through individual skirts normally grouped in clusters at the base of each leg. The types of subsoil dealt with in the Peninsular Malaysia and Gulf of Thailand surrounding region are conducive to the installation of driven piles only. The design of an offshore pile is fundamentally the optimization of pile length, size and make-up those are suitable to the requirement and supply. An interactive effort combining aspects related to geotechnical, structural and constructability are required to converge into a feasible, safe and economic solution. Other than the checking of the installation feasibility using a set of hammers in a given environment, driveability analysis is also used to define acceptance criteria for a majority of the offshore piles. Unlike short and end bearing piles in sand/soft rock, the piles in clayey subsoil regime often could not be rested on a dense strata where it could be met by a definite set criteria. Usually a measurement of blow counts determined and defined by driveability analyses forms the acceptance criteria to ensure a certain level of confidence of its fitness for the purpose coupled with an optimum penetration. While softness and uncertainty of the soil strata at target penetration may be resulted in possible overdrive, an unusual delay or the presence of an unidentified cemented layer or a boulder may cause early refusal or underdrive scenario. Hence, accuracy of the investigation, driveabilty study as well as the precautionary measures to avoid delays during driving are of equal importance."

Jan 1, 2015

By Kozo Takeda, Arashi Shimano

"Dry Jet Mixing (DJM) technique is widely known as soil mitigation technique with small ground displacement during installation comparing with other techniques. Some projects involving sensitive structures, however, require smaller impact than in conventional technique. In order to reduce ground displacement during DJM installation, this paper introduces systematic mixing technique, RD-DJM (Reducing Displacement – Dry Jet Mixing). RD-DJM is characterized by injection nozzle on the rim of mixing blade and fin plate on mixing shaft. These devices contribute efficient collection of injected air toward mixing shaft and result in reduction of ground displacement. The authors demonstrate successful performance of RD-DJM indicating difference between conventional installation and RD-DJM technique.INTRODUCTIONThe Dry Jet Mixing (DJM) method is one of the most common techniques in Japanese deep soil mixing field and characterized mechanical mixing of powdery binder with in-situ ground (dry-mixing technique). It is widely believed that DJM Method has great advantages in less quantity of binder to achieve the desired strength and less waste generation during installation.DJM method can meet the required strength with less binder content than wet mixing. And volume of binder of dry mixing is absolutely less than wet-mixing injecting considerable volume of binder slurry. This means that dry mixing causes less ground displacement compared with wet mixing.As the medium for forced feeding of the binder, the DJM method uses compressed air, which is blown from the mixing blade nozzles to scatter the binder and then recovered through the periphery of the mixing shaft to the ground surface. Because the binder is injected outward from the injection orifice at the root of the mixing shaft, a part of the air may escape to untreated areas due to the blockage of air recovery path around the mixing shaft. Figure 1 illustrates possible escaped air and leakage around installation location."

Jan 1, 2015

By Alan Christopherson

Nearshore construction projects often require installation of steel piles and specific methodologies of installing piles may adversely affect nearby species of concern. Water is an uncompressible medium which allows for easy transmission of energy through the water column. Energy transmission through water depends on the following factors for pile driving: 1) direct contact of the pile and the water; 2) the depth of the water column; 3) the size of the pile; 4) type of hammer; and 5) the energy of the hammer. Seasonal restrictions are usually the best practicable alternative for reducing habitat impacts when pile driving activities may adversely affect the species of concern. When seasonal restrictions are not practical other options need to be evaluated, including mitigation and noise attenuation devices. The broad array of mitigation options will not be discussed as part of this presentation but instead will focus on noise attenuation technologies. Dewatered cofferdams can be effective noise attenuators as they eliminate direct contact of the pile with water while driving. Also, introduction of a compressible medium, like air, near the energy source can provide sound energy attenuation. An unconfined bubble curtain is relatively inexpensive but is not effective in tidal marine projects or rivers and may have unacceptable secondary effects. Secondary effects must be evaluated as these can increase exponentially for larger projects. Secondary effects to the environment include air quality degradation from air compressor use, transportation costs for fuel and equipment, and the potential for injecting oily compressed air into the water column. The confined bubble curtain works well in nearly all environments. It usually is more expensive initially, relative to an unconfined air curtain, but there is less potential for harmful secondary effects. Generally, seasonal restrictions will be adequate to protect species of concern. However, there are conditions in which mitigation or one of the sound attenuation options should be utilized. Site specific factors, including the amount of energy being imparted into the environment, sensitivity of the species of concern, current, accessibility, length of time needed to complete the project, and the cost of the sound attenuation, should be factored into the permit evaluation.

Jan 1, 2013

By Abolfazl Eslami, Fatemeh Rostami, Sara Heidarie Golafzani, Mohammad Arabameri

Collapsible loess is classified as problematic soil found in most continents. The loess immediately collapses under stresses induced by axial compressive loading or the soil weight when exposed to moisture. In Iran, vast areas of the Golestan province are covered with aeolian loess deposits. This paper investigates whether the simultaneous effect of inundation and pre-loading in helical pile installation are operative and effective in improvement of Golestan loess. The effect of installation conditions on loess collapsibility is studied via two main approaches, i.e., field investigations and physical modelling. The experimental studies include installation of eight single helix piles in the Amirkabir University of Technology Frustum Confining Vessel, i.e., FCV-AUT. Also, four single helix piles with embedment depth of 3 m and diameter of 250 mm were installed in Golestan province and full-scale pile static loading tests were performed. The results indicated that the simultaneous application of crowd loading and water pressure during installation of helical piles results in better soil shear strength parameters. Moreover, high crowd stresses or low crowd stresses accompanied by water pressure during pile installation brings about similar load-displacement behavior of model piles installed in FCV-AUT and full-scale helical piles.

Oct 1, 2022

By Nabil F. Ismael

"Load tests were carried out to examine the ultimate bearing capacity of short, large diameter bored piles in connection with the construction of a multistory building on the Arabian Gulf in Kuwait. Testing included 0.45 m, 1.0 m, and 1.2 m piles installed through loose sand into a bearing stratum consisting of very dense cemented sands. All tests were carried out to failure. The base resistance and shaft friction were calculated using the Meyerhof method for a layered soil profile. The method employs the standard penetration test N-values. The results indicate that the piles are end bearing piles with a great portion of the pile capacity due to base resistance. The mobilized skin friction is small. The calculated pile capacities were very close to the measured values with the maximum difference not exceeding 10%.INTRODUCTIONShort, large diameter bored piles are used with increasing frequency for heavy structures in Kuwait, and the Gulf region where ground conditions indicate loose deposits of calcareous sands. The piles range in length from 8 m to 15 m with their base located in the dense-to-very dense, cemented sand bearing deposit. The design of these piles requires knowledge of the skin friction and point resistance in these soils. While field tests on driven piles are available (Ismael 1989, Ismael 1999), field test data on large diameter bored piles installed through loose calcareous sands into dense-to-very dense cemented or partially cemented sands are very limited at present. The results of three load tests carried out recently on bored piles at one site in Kuwait have become available. In these tests the failure load was either reached or can be extrapolated from the test results. It is important to examine and analyze the test results for the benefit of the geotechnical research and design engineers.This paper presents the soil conditions, pile installation details, and the pile load test data at the test site located in Shuwaikh, Kuwait. The site is facing the Arabian Gulf. Test results were directly analyzed and the point resistance, and skin friction were calculated. The ultimate capacities of the piles were calculated and compared with the measured values. The influence of the pile diameter on the settlement at ultimate and at working loads is examined"

Jan 1, 2017

By Nabil F. Ismael, Mohamed El Deeb

"The behavior of laterally loaded step tapered bored piles in calcareous sand was examined by field tests. Lateral load tests were carried out on straight and step tapered bored piles 5.3 m long embedded 5 m below ground level. All piles were installed by augering. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles have a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads. Test results indicate non linear response and substantial increase in lateral capacity and decrease of deflection for the step tapered piles compared with the 0.2 m diameter straight shaft piles. However, beyond a depth of 40% of the pile length, the strengthening of the pile section by enlargement of its diameter had little effect on the lateral capacity and the deflection of step tapered bored piles.IntroductionFor many structures on pile foundations the ultimate capacity under lateral loads is important and may be the controlling factor in foundation design. Examples include transmission tower foundations and fender piles at sea port facilities. Increasing loads on these structures has resulted in piles of large diameter and depth at a significantly higher cost.In this work, the use of step tapered bored piles with a larger diameter along the upper segment of the piles is examined by field testing and analysis on single piles in calcareous desert sands. Lateral load tests were carried out on straight and step tapered piles 5.3 m long embedded 5 m below ground level. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles had a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads for step tapered bored piles."

Jan 1, 2005

By Nathan A. Ingraffea

The use of steel sheet pile walls and drilled shaft foundation elements to enable up-down construction methods has been used successfully on recent high-rise structures with multi-story below grade parking. The John Ross Tower and The 3720 Tower in Portland, Oregon each make use of this system and are discussed in-depth. Up-Down construction involves the simultaneous construction of the building levels above and below grade instead of the standard construction technique of excavating and shoring the below grade construction before being able to build upward from the base of the excavation. Advantages of the up-down system include a shortened overall construction schedule, permanent basement walls that double as the temporary shoring walls, elimination of the typical continuous wall footing or grade beam at the building perimeter, increased use of recycled material (steel) while maintaining an overall decrease in total materials, elimination of wall forming costs, decreases in forming costs for slabs, decreases in waterproofing costs for walls and elimination of pile caps and/or footings for the building columns. Lessons learned during the construction of both buildings include the need for more extensive geotechnical boring information, descriptive sheet pile and drilled shaft specifications, a clear understanding from the design team on finished appearance of sheet pile and shafts, and careful consideration of the connection between both slabs and the sheet pile wall and slabs and drilled shafts.

Jan 1, 2008

By Nabil F. Ismael

Load tests were carried out to examine the ultimate bearing capacity of short, large diameter bored piles in connection with the construction of a multistory building on the Arabian Gulf in Kuwait. Testing included 0.45 m, 1.0 m, and 1.2 m piles installed through loose sand into a bearing stratum consisting of very dense cemented sands. All tests were carried out to failure. The base resistance and shaft friction were calculated using the Meyerhof method for a layered soil profile. The method employs the standard penetration test N-values. The results indicate that the piles are end bearing piles with a great portion of the pile capacity due to base resistance. The mobilized skin friction is small. The calculated pile capacities were very close to the measured values with the maximum difference not exceeding 10%.

By Ingrid Engeset, Solve Hov, Arnfinn Endal, Per-Anders Mortensen, Priscilla Paniagua, Bjørn Kristian Fiskvik Bache

During the last decades, it has become common practice in the Nordic countries to use dry deep mixing in soft clays with lime and cement in for example deep excavation pits in soft clay, or as a reinforcement of the passive zone within sheet pile walls. The shear strength of stabilised soils is affected by the stress conditions during curing and shearing. However, this is normally not taken into consideration. As the strength of the stabilised clay is stress dependent, excavation of the overlying soil will lead to a reduction of the confining stresses in the underlying stabilised soils which means that the shear strength will also be reduced. Under embankments on the other hand, the effect is reversed as the shear strength will be increased. In this study, laboratory tests have been performed on stabilised soils cured and tested under different stress conditions to quantify the stress effects in a Norwegian sensitive clay. In addition, direct simple shear tests on samples from in situ columns have been made with varying normal stresses. Results are presented showing an increase of shear strength of the stabilised soil with increased curing stresses, and an even higher increase with increased confining stress during shearing. The results are compared to field measurements along with a discussion of practical application of the findings.

May 1, 2022

By Sepideh Damavandinejad Monfared

"In recognition of the practicality of using inclined micropiles as elements for foundation support to resist static and seismic loading conditions, specifically in retrofitting projects, this study presents an investigation into the behavior of an inclined micropile subjected to simultaneous lateral load and bending moment. Three-dimensional numerical simulations are performed using the finite element method to assess the influence of micropile geometrical parameters such as angle of inclination, length, and diameter on the response of micropile-soil system. The Mohr-Coulomb failure criterion is used to define the behavior of soil and stabilized soil around micropile materials and the micropile, constructed of concrete and steel, is assumed to be elastic. The interaction between soil and micropile is taken into account by defining interaction elements covering both tangential and normal behavior. The study is carried out using nonlinear FEM analyses. The results of these simulations indicate that negative micropiles, in which slip surface deflects downward, have higher lateral load capacity than positive micropiles with slip surface deflecting upward. The conducted research also shows that increasing the diameter and the length of micropile increases the lateral load capacity. Increasing micropile diameter is more effective in increasing lateral load capacity. A relationship is developed from statistical regression analysis of the finite element modeling computations to estimate the lateral displacement of a micropile inclined at an angle of 30o in silty sands. IntroductionMicropiles are small diameter (typically less than 300 mm), cast-in-place, drilled, and grouted replacement piles with steel pipes which after being conceived in Italy (Lizzi,1978), were originally developed for underpinning existing structures (Bruce et al.,1990) to arrest and prevent structural movement, upgrade loadbearing capacity of existing structures, repair or replace deteriorating or inadequate foundations or raise settled foundations to their original elevation."

Jan 1, 2017

By Sepideh Damavandinejad Monfared

In recognition of the practicality of using inclined micropiles as elements for foundation support to resist static and seismic loading conditions, specifically in retrofitting projects, this study presents an investigation into the beh avior of an inclined micropile subjected to simultaneous lateral load and bending moment. Three-dimensional numerical simulations are performed using the finite element method to assess the influence of micropile geometrical parameters such as angle of inclination, length, and diameter on the response of micropile-soil system. The Mohr-Coulomb failure criterion is used to define the behavior of soil and stabilized soil around micropile materials and the micropile, constructed of concrete and steel, is assumed to be elastic. The interaction between soil and micropile is taken into account by defining interaction elements covering both tangential and normal behavior. The study is carried out using nonlinear FEM analyses. The results of these simulations indicate that negative micropiles, in which slip surface deflects downward, have higher lateral load capacity than positive micropiles with slip surface deflecting upward. The conducted research also shows that increasing the diameter and the length of micropile increases the lateral load capacity. Increasing micropile diameter is more effective in increasing lateral load capacity. A relationship is developed from statistical regression analysis of the finite element modeling computations to estimate the lateral displacement of a micropile inclined at an angle of 30o in silty sands.

By Sebastian Fischer, Rolf Katzenbach, Steffen Leppla

"The risk management in the case of liquefaction is one of the most serious and also difficult issues in geotechnical engineering because failure caused by liquefaction is always a sudden failure without ahead indication. For that reason ground improvement technologies for the prevention of liquefaction are necessary. The paper explains the responsible and effective risk management. Methods for the risk management and stabilizing the soil sustainably are described in detail.1. INTRODUCTIONDue to population growing more and more settlement area is needed, which is often including improper regions (e.g. mountain and coast regions) with raised risk of various kinds of disasters. But also in densely populated areas the risk of disasters like landslides can occur. One reason for the raising of risk in densely populated regions can be the opencast mining for raw material production. An essential element of the opencast mining is the loose deposition of the removed overburden, the so-called “overburden dump”. When an opencast mining is running out of the raw material, an opencast hollow remains in landscape. The slope areas of these hollows mostly consist of loose bedded material of the overburden dump. Due to the end of groundwater conservation these loose bedded slope areas are flooded. In consequence the slopes are in extreme danger of becoming liquefied. The result of a liquefaction in these slopes will unavoidably be a slope slide. Such a slope slide can extend up to several hundred meters into the landscape and can move several million cubic meters of material. An upsetting example for such a landslide is the slope failure in the German city of Nachterstedt on July, 18th 2009, which made necessitate remedial measures and also prevention works for the further utilisation of the region. The phenomena of liquefaction is not limited of slopes in series of opencast mining. Especially in regions with a highly appearance of earthquakes the phenomena of liquefaction is well known.2. RISK MANAGEMENTAn essential part for the stability assessment of slope systems is the investigation of sensitivity against liquefaction. In the case of given sensitivity against liquefaction there is no calculation method according to soil mechanics to determine the factor of safety against slope failure. Just for the case that sensitivity against liquefaction is not met, a comparison of the load (effect) E and the resistance R which is the traditional verification of stability against slope failure, can be calculated (Figure 1)."

Jan 1, 2015