Search Documents

By Wei Tu

A grade separation was required to allow uninterrupted traffic crossing for a busy rail spur and a county road. The grade separation was achieved by creating a 30-foot (9-meter) high embankment that incorporates two multiplate tunnels and allows the passage of a rail spur and an existing county road. The site is located in an abandoned meander channel in the floodplain of the Mississippi River, near Osceola, Arkansas, and is underlain by more than 40 feet (12 meters) of soft clay and interlayered clays, sands and silts. Without soil improvement, the post-construction settlement would exceed 3 feet, slowly crushing the proposed tunnel structure and cutting off the railroad. Preloading, combined with vertical drains, was used to accelerate the consolidation of the underlying soil layers and to reduce the post-construction settlement under working loads. Six settlement plates were installed to monitor the progress of consolidation under surcharge load. The Asaoka observational method and the hyperbolic fitting method were used to analyze the measured settlement data to predict the end of primary settlement. The in-situ consolidation coefficient, ch, was back calculated from the measured settlement data. The stress release caused by the removal of the preloading surcharge load and the tunnel installation was determined using a Plaxis 3-D finite element model. The measured and predicted settlement using Hansbo's analytical solution demonstrated reasonable agreement. Early removal of the surcharge and construction of the tunnel prior to reaching the end of primary settlement was accomplished by analyzing the post-excavation stress reduction achieved via tunnel construction.

Jan 1, 2009

By Andrew Stauble

This project included the replacement of the Long Island Railroad (LIRR) Atlantic 6 Bridge in New York City, which services rail traffic and spans the Van Wyck Expressway and frontage roads. The bridge re- placement was part of an overall project to widen the Van Wyck Expressway between Kew Gardens and John F. Kennedy Airport, which serves as the major route for vehicular traffic between the airport and the city. The railroad bridge crosses the expressway and frontage roads in a significantly congested area, and it services an average of approximately 140,000 commuters per day through- out the boroughs of Manhattan, Brooklyn and Queens. The existing bridge superstructure and foundations were to be demolished and new structures and foundations were proposed to be constructed at the bridge's east and west abutments and center pier. The new bridge would be supported on driven H-piles. To facilitate the construction of the new bridge's abutments and center pier, a support of excavation design was required to support the grade around the existing structures. The design shown on the contract drawings included a driven soldier pile and lagging wall with multiple rows of drilled tiebacks at the abutments to laterally support excavation heights of up to 36 ft (11 m). The existing abutments are located directly adja- cent to frontage roads that have an extremely high vehicle traffic volume,

Aug 1, 2023

By Kenneth M. Berrry

A unique situation has developed at an abandoned coal mine in St. Clair County, Illinois. Subsidence features have been observed at the ground surface over the mine including settlement of a pair of bridges for Illinois Route 158. The Illinois Department of Transportation (IDOT) is currently replacing the two bridges. Foundation treatment for the two new bridges included backfilling the mine void. The light rail system for St Louis (MetroLink) is also constructing a bridge over the same abandoned coal mine less than 1000 ft from the Route 158 bridges. The new MetroLink bridge is being constructed using piles which extend through the coal mine and overlying bedrock in order to transfer the loads to below the mine floor. The differing foundation types for the IDOT and MetroLink bridges were due to geometry and economic factors involved with the individual structures.

Jan 1, 2001

By Daniel W. Mageau, Larry W. Applegate, Aaron K. McCain

"An innovative method of ground freezing was successfully tested to create a “dry” excavation condition for a new building foundation at a site in downtown, Miami, Florida. The subsurface conditions in Miami generally consist of very porous, weak limestone and sand with groundwater near the surface. Water flow through these materials can be very high. Dewatering is extremely restricted in Miami so deep below-grade structures are rare and expensive. A new, innovative method to allow deep excavations in dry conditions without dewatering involves the creation of a thick, temporary, frozen soil plug below the planned excavation depth across the entire site to cut off vertical groundwater flow during construction. Frozen soil is impermeable and very strong and has long been used for temporary structural and water-tight shored walls. Using the same proven principals, frozen soil plugs are very effective at cutting off water from the bottom of the excavation as well as resisting upward buoyant forces. This new freezing method can be used for fairly deep excavations in new building construction supported on deep foundations. The building piles act as temporary anchors for the frozen plug to resist very high upward buoyant pressures until the permanent structural slab is completed.IntroductionUnlike other Cities, below grade basements are rare in Miami. The few basement foundations constructed have utilized a cumbersome and expensive method of excavation and shoring involving underwater excavation, tremie slabs, and commercial divers. The key issue for underground construction in this area of the country is the vertical flow of groundwater through the base of the excavation. To deal with this issue in the past, the contractor first installed all of the building piles and the perimeter shoring walls. Then, interior sheet pile walls are installed to create small manageable excavation pits. Each pit is then excavated through standing water “in-the-blind” and around the buildings support piles. The final excavation, interior struts, and inspection is performed by commercial divers. Finally a thick foundation tremie slab is poured under water. This method could be successful but proved to be time consuming and expensive. In addition, some building piles were occasionally damaged during the under-water construction process."

Jan 1, 2015

By Gerald Verbeek, David Tara

"When selecting an impact hammer to drive a particular pile, the decision is often based on local experience. In those cases, the contractor falls back on previous experience or draws on the experience of the hammer manufacturer to select the hammer that will be able to do the job. Obviously, a more scientific approach would be to perform a pile driving simulation using one of several commercially available software packages (e.g., GRLWEAP, AllWavePDP or PDPWave).However, this type of analysis requires quite a bit more effort. First, an accurate model of the pile driving process has to be developed, which includes a model of the soil profile at the job site and input into the analysis program. Then, the model must be analyzed to assess whether the combination of hammer, pile and soil model work.Over the years, numerous individuals and organizations have tried to develop something that would fit nicely in between these approaches: something more advanced than a gut feeling yet something that could be done on the back of an envelope; in other words, a “Goldilocks” approach — not too simple, not too complex, but just right.Screening Tool CriteriaThe goals of the approach are twofold: (1) select the appropriate impact hammer to drive an open toe steel pipe or H-pile, and (2) then use the model for the subsequent high strain dynamic testing (HSDT). The Goldilocks approach centers around five different criteria.1. Maximum Driving StressTo minimize the risk of damage, the maximum driving stresses are generally limited to 80 to 90% of the yield stress (fy) of the steel section. This approach does not consider issues such as hammer alignment, initial imperfections, denting and/or elastic buckling, and pile material fatigue history. However, even when these issues are not applicable, limiting average stresses to 0.9fy or even 0.8fy does not necessarily mitigate the risk of pile damage (Mostafa, 2011)."

Jan 1, 2017

By R. Lee Wooten, David R. Shields, Darren D. Clark

"Borehole permeability tests that measure flow or head changes in boreholes located within seepage barrier walls are commonly used to estimate the in situ permeabilities of those walls for quality control and assurance. The current state of practice for estimating permeabilities from these barrier wall borehole tests is to use equations published by M. J. Hvorslev in 1951. Hvorslev’s borehole test equations model an infinite stratum of uniform permeability, which is not the actual condition for a test performed in a low permeability barrier wall located within a high permeability stratum. We examine and develop alternative equations based on line source analytical models, which more closely match barrier wall test conditions. We describe how these alternate equations can be used to estimate barrier wall permeabilities from borehole tests and compare the results to those obtained from the Hvorslev models. We also provide recommendations that consider differing upstream and downstream water levels.Barrier Wall Permeability Tests - State Of PracticeThe installation of seepage barrier walls has become more common in a variety of applications ranging from dams and levees to contaminated sites requiring retardation of groundwater flow. The types of seepage barrier walls and installation methods include soil-bentonite, soil-cement-bentonite, concrete, self-hardening slurry, geomembranes, and sheet piles, installed with various soil mixing, slurry-supported trench, and driving methods.Owners and contractors have used a variety of methods to evaluate the permeability of these seepage barriers. The following table lists commonly used quality control/assurance tests for evaluating the permeability of a seepage barrier."

Jan 1, 2016

By Scott A. Walker, Gabriel J. Alcantar, Brian Zuckerman, Ramin Golesorkhi

"The new San Francisco 49ers Levi’s Stadium is part of the next generation of sporting facilities. Constructed in Santa Clara, Calif., the new structure has 68,500 open-air bowl seats and includes a 7- story tower housing more than 150 suites. The overall project includes the stadium structure, elevated open pedestrian walkways, commercial community space, three new pedestrian bridges and improvements to the adjacent light rail station. Sustainable design for the project includes a green roof, photovoltaic panel and a ground source geothermal system. Stadium-wide next-generation Wi-Fi capability is another feature. The design-build project team included HNTB (project architect), Magnusson Klemencic Associates (MKA, structural designer) and a joint venture of Turner Construction and Devcon Construction (TDJV, general contractor).During preconstruction, the 49ers’ original design team and the design-build team formed later worked together to facilitate communication and provide continuity. This helped to meet the project’s aggressive schedule. Working directly for the 49ers, with the design-build team, Treadwell & Rollo (T&R) served as the geotechnical engineer of record for the project from preliminary to final design and through construction. Although not contracted directly to TDJV, the stadium ownership encouraged direct interaction between T&R and TDJV and improved responsiveness to geotechnical issues during design and construction.Subsurface ConditionsThe new stadium lies within the Santa Clara Valley, a deep alluviumfilled basin resulting from historic movement on the active and potentially active strike-slip and thrust faults that bind the valley. The valley is filled with Holocene age (approximately 11,000 years old to present) alluvium, consisting of levee and basin deposits, with bedrock more than 750 ft (229 m) beneath existing ground surface. The stadium site is between two of the highly-active faults in California, the Hayward Fault 6.8 mi (11 km) northeast, and the San Andreas Fault about 11.8 mi (19 km) southwest."

Jan 1, 2014

By Chul Soo Park, Juhyung Lee, Duhyun Baek

"In this study the preliminary design of suction pile as the supporting system of the concrete floating structures was performed at the offshore pilot project area in Korea. The suction pile of the floating structures has to satisfy the lateral resistance against external force evaluated from the marine and structure conditions, as well as the penetration ability according to the soil and seepage conditions. In the design, the required penetration depths for lateral resistance were evaluated with different diameters of cylindrical steel suction pile, and the design suction pressures at each penetrating depths were assessed through the comparison of penetration forces and penetration-resistances. Finally, the optimal dimension of suction pile for the pilot project area was proposed.IntroductionInterests in sea spaces have rapidly increased around the world due to limitations in use of lands. Such increase has resulted in construction of numerous marine structures aimed at expanding the use of sea spaces and developing marine resources. South Korea also needs to secure construction technologies for floating infrastructures on its relatively deep seas. Foundations for floating structures consist of anchors and mooring systems rather than driven piles or cast-in-place piles, due to limitations in equipment operation or economic feasibility. Anchors and foundations used on the sea include drag anchors and suction piles, but the suction piles are more widely used for reasons regarding uncertainties of calculation of bearing capacity and construction. Large-diameter suction piles are generally used to utilize fully their penetration ability, which is proportionate to the square of the foundation diameter, and the length-diameter ratio (L/D) does not exceed 6 (Randolph et al., 2005; Andersen et al., 2005). Recently, a design and construction technology using group suction piles consisting of medium-diameter suction piles and concrete pile caps is being developed as an alternative to the conventional large-diameter mono suction piles. In addition, pilot projects involving the group suction piles of mediumdiameter are currently being reviewed for the southwest coast area in Korea. In this study, therefore, preliminary design for installation of medium-diameter mono suction piles as the supporting system of the concrete floating structures was performed, and suction pressures, penetration forces and resistances, and lateral loading capacity with diameters were reviewed."

Jan 1, 2017

By Douglas L. Scaggs

Over the past several years, pile foundations have grown to meet the demands of larger and heavier structures. As the foundations have grown, so has the need for larger and more robust piles to carry the increased loads. Seismic considerations have also required larger and tougher piles to withstand the added component of supporting structures during earthquakes. While H-piles, precast concrete piles, timber piles and small pipe piles have been the product of choice, many applications are now calling for much larger piling requiring larger equipment and presenting the contractor with new challenges. This paper is not intended to be a ?how to? guide as much as a discussion on the potential pitfalls a contractor should watch out for when considering a project where mega piles are required.

Jan 1, 2013

By Thomas M. Caruso

Construction of a new ship dock at a major Philadelphia area refinery required geotechnical design and field consultation. The new dock, which consists of a system of mooring dolphins and platforms, will be capable of docking the Stena V-MAX Oil Tanker (V-MAX). The 1100 ft long V-MAX is currently the largest tanker to travel the Delaware River and will induce significant lateral loads on the new ship dock. Lateral loads induced on the dock will be resisted by over 200 pipe piles installed on a batter. The piles used for support of the dock included 20 and 30 in. diameter reinforced, concrete filled pipe piles. Complete construction of each pile included driving of the pile to the design ultimate capacity, flushing the pipe pile casing clean of overburden materials followed by drilling rock sockets into the underlying Wissahickon Formation. Variations in depth to bedrock, rock quality and degree of weathering and presence of very hard quartzite lenses created a complex geologic environment that presented challenges for the pile/rock socket design and installation. The design of the pile system, installation methods, QA/QC and testing (Pile Dynamic Analysis), as well as the challenges that were encountered through the duration of the project are presented and discussed.

Jan 1, 2008

By Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"Over the last 10 years, the Minnesota Department of Transportation (Mn/DOT) has had a very active program of replacing many major bridges, large structures spanning the Mississippi River. The deep foundations for these new structures include both drilled shafts and large diameter open-ended driven steel pipe piles. Most of these projects included load tests, both axial and lateral.The geology of this area of Minnesota includes some interesting foundation challenges, including highly organic and compressible very soft silts and clays to very dense sand and gravel overlying sedimentary bedrock. In some cases scour requires embedment into rock, and the bedrock formations may range from very soft sandstone to very hard dolostone. Artesian groundwater conditions can sometimes complicate drilled shaft construction, but the rock is otherwise very favorable for drilled shafts. Experience with the open-ended driven steel pipe piles (typically 42 and 48 in, 1.07 and 1.2 m diameter) suggest that these piles most often penetrate even dense granular materials to achieve bearing on rock. Experiences with drilled shafts socketed into the soft sandstones demonstrate that these rocks provide very favorable conditions for drilled shafts, so long as suitable construction practices are followed. Here we present several recent case histories regarding the foundation design and construction of major bridge projects in the vicinity of Minneapolis, Minn., including the Wakota Bridge, the I-35W replacement, the Lafayette Bridge, the Hastings Bridge and the St. Croix Bridge. Some lessons learned from construction and load testing of both types of foundations are described along with implications for design in similar soil and rock conditions."

Jan 1, 2013

By Keith MacKay, John Carter, David Siddle, Fernando Faminia

"The River Green Residential development, is located in the municipality of Richmond, BC adjacent to the Fraser River. Ground conditions at the site consisted of medium to fine grained alluvial sands and a high groundwater elevation. A temporary low permeability retaining wall was required in order to facilitate the construction of an underground parking structure without inducing settlement of adjacent structures, which include the Richmond Olympic Oval; part of the legacy of the Vancouver 2010 Winter Olympics. Golder Associates Ltd. and GeoPacific Consultants Ltd. utilized Cutter Soil Mixing (CSM) technology to enable construction of a continuous combined low permeability cut-off and retaining wall around the perimeter of the property. The 350m long wall was keyed into marine clay at a depth of 28m below ground surface, and contained H-Pile reinforcement installed at regular intervals. The CSM technology provided many benefits for this project, allowing the combined cut-off and retaining wall to be constructed within a very narrow footprint (650mm width). The low noise impact and near vibration free construction of the CSM equipment provided minimal inconvenience to nearby stakeholders during construction. To reduce dewatering volumes during excavation and prevent significant water-table drawdown the Hydraulic Conductivity requirements for the wall were 1 x 10-7 cm/s or less. Project specifications called for a different strength requirement for upper and lower portions of the wall. The top 13 meters of the wall required an Unconfined Compressive Strength (UCS) of 4MPa to act as a retaining and cut-off wall, whereas the bottom 15 meters of the wall required a UCS of only 0.5 MPa to act only as a cut-off wall. Wet-grab and core samples were obtained from the panels to confirm the UCS and Hydraulic Conductivity specifications were met.INTRODUCTIONGolder Construction Inc. and GeoPacific Consultants Ltd. conducted the design and construction of a deep soil mixed cut-off and retaining wall system. The “dry-box” solution was used to surround the excavation of an underground parkade and prevent flows of groundwater into the excavation."

Jan 1, 2016

By Dave Paul

Dam rehabilitation involves a range of design, construction, and operation risks, some of which are not encountered in new dam construction. These risks can have significant impact on project schedule and project budget. Owners, engineers, and contractors need to understand these risks. Existing dams typically were designed in an era of design and construction standards that have been upgraded and changed. Modern standards will impact the construction approach taken and involve understanding the earlier standards. Knowledge of historical standards/practices as well as current design standards and construction methods is valuable for developing and designing rehabilitation components. Construction records and as-built drawings are valuable when they are available. Rehabilitation projects often consist of older projects where as-built documents or construction records are not available. Where these records exist, many (most) times, they do not fully reflect the current conditions within the dam and appurtenant works. leading experienced practitioners to “expect surprises” both during investigation of the existing facility, as well as during construction. “Surprises” should be expected even when historical records of investigations, design and construction are available. Unknowns, be they known unknowns or unknown unknowns, can be planned for by developing an approach for the design and construction process to identify potential issues/problems, or at least alert the designer and contractor of potential issues. A Risk-Based approach applied for the entire life of the rehabilitation project can be used to alert the parties of potential “surprises” and provide direction for mitigating issues as they arise. This type of approach is particularly effective when the process includes senior practitioners with decades of design and construction experience in all aspects of dams. Minimizing impacts created by “surprises”, particularly during construction, can result in an improved project meeting budget and schedule goals and design standards. This paper identifies and categorizes risk types salient to dam construction, reviews the process of risk identification and analysis, discusses guidelines for risk allocation, reviews strategies to mitigate risks, presents several case studies where risk mitigation strategies were employed successfully (or unsuccessfully), and presents lessons learned. The paper concludes with a summary and recommendations for best practices for Project Risk Management and mitigation that can be used by: Owners; Design Engineers; and Construction Managers, in planning, design, pre-construction and construction phases of dam related projects.

By Raymond Henn

Yes we have also used some however, again because of the nature of the maintenance window where we have that two hour (at best) window every night and due to the numerous other crews that are wanting to get in to do the other types of maintenance activities, we don't know if we are going to be getting into that same area from one night to the next. So even with the dormancy additives that one can add to cementitious grouts (that are good up to 72 hours) we don't know if we are going to get back in to the same locations from one week to the next. That's why I use the term "the forgiving nature of the acrylamide". It allows us to ream out the hole allowing us to use the exact same hole without having to re-drill a new hole. The program started in 1997 and we have a budget between labor/materials and equipment of 4.5 million dollars on a year to year basis. For the next few years that is going to come down drastically because the program is going to be more of an ongoing maintenance program. The program started in 1997 and we have a budget between labor/materials and equipment of 4.5 million dollars on a year to year basis. For the next few years that is going to come down drastically because the program is going to be more of an ongoing maintenance program. Up to the end of 2001 we were just over 1.7 million liters of between AV100 and AV118 grout. Of that, approximately just under 200,000 was AV100 and the remaining balance was AV118.

Feb 10, 2003

By George Filz, Peter R. Cali

"Unnecessarily restrictive specifications could be limiting the cost effectiveness of deep mixing (DM) applications and therefore limiting use of DM on projects where there are other options. Excessively restrictive standards demanded for strength and permeability certainly increase contractors’ bid prices, and costing the owners and, in the case of Government projects, the taxpayers more than necessary. Yet, lax or ineffective specifications often exist for some vital components of the quality assurance and quality control. In this paper, specifications for key elements of DM design and construction are examined. Recommendations are made to improve and streamline DM specifications to better serve the common objective of constructing a safe and cost effective ground improvement project.INTRODUCTIONSpecifications should, at their best, convey the project design requirements and provide clear direction to the contractor regarding requirements for submittals, materials, execution, measurement, schedule, and other aspects as necessary. The specifications should not be overly conservative, restrictive or ambiguous, and they absolutely should not be deficient in measurement of quality. Guide specifications or recycled sections from previous projects often form the template for new project specifications. But standards that appear in guide specifications or from former successful construction should be critically scrutinized by the designer for relevance before using the copy/paste functions of the specifications writer’s keyboard. Because work does not always go as smoothly as planned, specifications for remediation of non-compliant construction should be clearly stated and enforced. Often, non-compliancy is reviewed after-the-fact and deemed to have met the design intent, indicating that either the specifications were too restrictive or the enforcement too weak.The Federal Highway Administration Design Manual: Deep Mixing for Embankment and Foundation Support, October 2013, was written by a panel of DM expert design practitioners and contractors. Guide specifications are included as Appendix C of the FHWA manual. Those guide specifications have been updated in the deep mixing section of the www.GeoTechTools.org website, and the updated specifications represent the most complete and authoritative compilation published to date. Although the specifications for DM at www.GeoTechTools.org are current and complete, and they portray the state-ofthe- practice, they too must be modified to fit specific DM applications, project needs, and site conditions. The keys to a good set of specifications are to prescribe construction only to the level that is required to meet the design intent, to require appropriate quality control and quality assurance (QC/ QA) activities, and to clearly address remedial measures required for non-compliant work."

Jan 1, 2015

By Vishal Pathak, Shailesh A. Godhuly

Ground Modification System in terms of Jet Grouting for soil strengthening and mass stabilization was engaged for a power plant project in an international power project, engineered by L&T-S&L. The site Geology consist of cohesionless type of sandy alluvial deposits (silty fine sand) as the main formation. Ground water table is encountered at shallow depth. Geological interpretation is done using soil investigation data along with CPT’s. This paper discusses design and implementation of jet grout technique to improve the mechanical behaviour of soil. To distribute load evenly from superstructure, a layer of growmast (drainage blanket) is laid above jet grout columns. Settlement evaluation is done using Finite element analysis with Plaxis 2D and Settle 3D. In the project, selected equipment foundations are resting on jet-grout columns including vibratory equipment like 144MW Gas Turbine etc. The project has been commissioned in September 2021 and operating with full capacity.

Sep 1, 2022

By Leonhard Weixler, Jean Wehbe, Gordian Ulrich, Franz-Werner Gerressen

"As alternative energy industries pick up speed internationally, and as government regulation and restriction limit the use of impact hammers due to environmental limitation from construction induced noise during pile driving operations, unconventional solutions for more complex offshore foundation installations have become a necessity. Manufacturers and equipment suppliers race to develop alternative techniques to accommodate for offshore foundation construction in various soil conditions and at greater water depth. The FLYDRILL, and the Seabed-Drill BSD are two innovative systems for the installation of offshore monopiles with reduced environmental impact.INTRODUCTIONThe FLYDRILL and the Seabed-Drill were born from techniques in the design and construction experiences gained from land based foundation drilling systems over the past 25 years. As the alternative energy industry ventures into uncharted territory of deeper water for offshore wind farms, fast current regions for tidal energy, and increasingly challenging soil conditions and project complexity, the advancement and development of new innovative equipment system and drilling techniques have become a necessity.The systems described herein show the development of the so called “FLY-Drill” system, and the all new “Seabed-Drilling” equipment applied at the first ever made job using a seabed drilling rig.FLY DRILLThe FLY DRILL method is a completely new concept for bored piling. The drilling unit with rotary head, Kelly bar, and drilling tool is suspended by the hoist rope of the base carrier crane. The hydraulic power for the drill unit is provided from the base crane.The drill head is fixed on the casing with a hydraulically operated clamping system during the drilling operation. When emptying the drilling tool, the clamp cylinders are opened and the complete unit is swung sideways."

Jan 1, 2017

By P. V. Chandramohan

"The paper deals with the arrangement of structural members for a retaining structure used as a berth in the port of Krishnapatnam. The height of retention is 24.3m. A T-shaped diaphragm wall acts as the retaining surface. A relieving platform has been provided at the top to ease lateral earth pressure on the wall. The diaphragm wall is tied back to a combination of vertical and raker pile. Later, this arrangement was altered to replace the relieving platform with just lowering of ground level below the berth. The tie back was changed to a classical A-frame anchorage. At certain reaches, installation of piles pointing towards the rear was obstructed by a conveyor structure. The anchorage was then changed to include a vertical pile and a pile that points towards the front of the berth. Change in position of inclined pile alters the force in the pile from compression to tension.GeneralPort is a major link in the multimodal transport chain. Berth is the heart of the Port infrastructure. It is here the ocean freight changes to land transport. The change-over, warrants special type of heavy duty handling equipment. The equipment and the process necessitate deep seated foundations. On one side of the berth, deep drafted ships would be berthed. But adjacent to this heavy duty cranes would be operating at the deck level. Berths are of various types. Some are founded on piles and may project into water. Some operators prefer a retaining structure. At the port of Krishnapatnam, a retaining structure was preferred. Dredged level at the berth was to be -20. Deck of the berth was at +4.3. This meant that the height of retention of soil was 24.3m. Ports are generally located near the coast. Subsoil in the port area generally consists of cohesive material of low shearing strength. The berth has to cater to imposed vertical and horizontal loads.Structural functionFor bulk cargo and containers, berth has to support the two crane tracks. These tracks will carry heavy wheel loads of the crane. Besides, the space between the tracks would be used for stacking of cargo or hatch covers. In short, the deck will be subjected to heavy surcharge. This vertical load will manifest as additional lateral force on the retaining wall. Since the height of soil to be retained is high, it is a practice to relieve the lateral earth pressure due to the heavy surcharge of the wall. This is done by providing a relieving platform. The surcharge of superimposed load on the deck and the self-weight of the soil up to a few metres below would be relieved by a suitable platform. This vertical load would be transferred directly to deeper levels through piles. Mooring pull is a horizontal force exerted by the vessel on the bollards towards water side. Berthing force is exerted by the vessel during berthing, through fenders and acts towards land side.Diaphragm walls are usually employed as the retaining face. If the height of retention is less, these walls can cantilever out but in the case of large retention, they have to be tied back. The ties are to be anchored on to suitable arrangements like a dead-man or an A-frame. Berthing structure in the early stages at Krishnapatnam port is shown in fig 1."

Jan 1, 2015

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By Dardis J. T. II, P. G. Reinhall

"Impact pile driving of steel piles in marine environments produces extremely high sound levels in the water. It has been shown that current pile driving noise attenuation techniques provide limited noise reduction because significant noise is transmitted through the sediment into the water. To solve this problem, we have developed a double walled pile to decrease the total noise transmitted into the water.The double walled pile consists of two concentric tubes connected by a special driving shoe, allowing for an air gap between the two tubes. The double walled pile is driven into the sediment using traditional equipment by striking the inner tube only. The air gap between the inner and outer tube prevents the radial deformation wave produced by the pile hammer from interacting with the water and the sediment. In one embodiment of the double pile design the inner tube can be removed and repeatedly reused.In this paper we report on the results from a recent full scale field test in Puget Sound, Washington. The use of these double walled piles reduces the peak sound pressure over 20 dB relative to single walled piles. We also show that only a 3 to 6 dB reduction is obtained when a bubble curtain is used on a single walled pile.INTRODUCTIONImpact pile driving of steel piles in marine environments produces extremely high sound levels in the water. It has been shown that current noise attenuation techniques provide limited noise reduction because the noise from pile driving is transmitted through the sediment into the water. In [1,2] we showed, using modeling and field data, that the primary source of underwater sound from an impact driven pile originates from radial expansion of the pile as the compression wave propagates down the pile after each strike. The radial expansion is coupled to the compression wave through the Poisson’s ratio of steel. As discussed in [1], the supersonic radial expansion wave (with respect to the water) produces an acoustic field in the shape of an axisymmetric cone, or Mach cone. We showed in [3] that the ability of any sound shield that surrounds the pile in the water only (such as a bubble curtain or a surrounding double wall engagement) to attenuate the sound in the water is limited by the fact that an upward moving sound Mach wave is produced in the sediment and is transmitted into the water. To improve the performance of bubble curtains and other noise shields in the water, it is necessary to attenuate the noise emanating from the sediment into the water. Figure 1 illustrates how sound from the seabed leaks out from the sediment, limiting the effect of the surrounding bubble curtain."

Jan 1, 2017