Search Documents

By Y. Obara, A. Sato

"Limestone is one of the most important mineral resources, and in Japan it is only one mineral which can be fully supplied by the domestic product. Generally limestone mines in Japan located at mountainous regions, and the combination between bench-cut method and the carry-out system using vertical shaft is widely used in the domestic mines. During mining operations, the occurrence of the blockage in the vertical shafts is very serious problem. Once the blockage in the shafts is occurred, a lot of works and dangerous procedures are necessary to solve the problems. It is thought that blockage is influenced by the cohesion and friction coefficient due to clay minerals thrown into the vertical shafts, however, the quantitative and precise reason is not revealed yet.In this study, the process of blockage occurrence was simulated by 2-Dimensional Discrete Element Method (DEM). In the 2D-DEM analysis, discontinuous circular particles are generated, and the individual movement of each particle is calculated by forward difference method. In the analysis, several typical ore distributions are applied, and the DEM analysis was conducted under the various combinations of cohesion and friction coefficient. From analytical results, it was found that the friction coefficient strongly influences to the occurrence of blockage and there were a threshold values which blockage does not occur. Several kinds of shaft shape were also simulated towards different ore size distributions, and those influences to the blockage occurrence were also discussed."

Jan 1, 2015

By Ajit K. Sinha

"Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentaryhosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3070 to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

By Zainelabdin Khalid Zainelabdin Elfaki

The influence of partially replacing cement with marble waste on the workability and compressive strength of concrete bricks was investigated. Three replacement percentages, 10%, 20% and 30% weight marble waste, were used with different curing times of 7, 14 and 28 days. Two specimens were prepared for each percentage and curing time. For this study, marble powder from the Mining House Company in Saudi Arabia was used. It was observed that the replacement of cement in Concrete brick with marble waste enhanced the loading strength and the workability of the prepared concrete bricks. It was also observed that 20% replacement of cement with marble waste was the best replacement percentage compared to the other replacement percentages tested. Marble waste from manufacturing companies, either in powder, sludge or slab form, has negative impacts on the environment. In contrast, reusing marble waste has both economic benefits (i.e., selling the marble waste) and lessening the need for raw resources.

Jan 1, 2014

By H. Asgari, A. G. Odeshi, J. A. Szpunar

In the present study, the dynamic response of AZ and AE cast magnesium alloys to shock loading, are compared for strain rates ranging between 900 and 1200 s-1. Texture measurements showed that after shock loading, the (00.2) basal texture component of both alloys was strengthened. However, the strengthening magnitude was higher for AE samples. Also, it was observed that the twinning fraction decreased in both alloys with increase in the amount of alloying elements. In addition, cracks are formed at the interface between matrix and second phase particles in the AZ alloys. However, crack nucleation and fracture in AE alloys occurred at the sites where twins accumulated. Furthermore, analysis of the dynamic mechanical behaviors showed that the ductility of AE grade is higher than that of AZ alloy for all strain rates used in this research. This difference was explained by differences in deformation mechanisms of these alloys.

Jan 1, 2014

"Sink-float analysis is often used to obtain yield-ash and density partition curves in the coal industry. These provide a valuable tool for evaluating the performance of a separation process. However, for dense minerals, obtaining complete grade-recovery and density partition curves is more difficult due to the lack of heavy liquids available with the required densities. This paper examines a potential solution to this problem which is to perform batch fractionation of mineral samples in a laboratory-scale REFLUX™ Classifier using high viscosity fluidising liquids. The REFLUX™ Classifier is a gravity separation unit consisting of a system of parallel inclined channels positioned above a vertical fluidised bed. Operated in semi-batch mode, a charge of particles is fluidised from below and particles up to a certain density are elutriated from the top of the system. The fluidisation rate is then increased incrementally to fractionate the sample at progressively increasing densities. Previous work by Hunter et al. (2014) and Iveson et al. (2015) has shown that this method provides excellent agreement with yield-ash and partition curves for coal, especially when glycerol solutions are used as the fluidising liquid. This approach has now been extended to obtain the grade-recovery and density partition curves of high density mineral samples. This method has the potential to provide the minerals industry with an effective tool to evaluate the performance of unit operations separating at cut points higher than the available heavy liquids.INTRODUCTIONMeasuring efficiency and effectiveness is of key importance in the continuous improvement of mineral processing plants. For density based separation, one way the performance of a process can be evaluated is the measurement of density-based partition curves. Currently, this is done in the coal industry using the sink-float method, where heavy liquids are used to fractionate particles into discrete density intervals. However, with high density minerals such as iron ore, liquids of sufficient density are rare, and in most cases also pose serious health and safety concerns to laboratory operators. Most commercial laboratories do not perform sink-float separations above a density of about 4400 kg/m3, the maximum density of Clerici solution without operating at excessive temperatures (Koroznikova, Klutke, McKnight & Hall, 2007; Rosenblum, 1974)."

Jan 1, 2016

By Q. Ricoux, F. Goettmann, A. Maihatchi

"Electrodeposition processes are widely used in the metallurgical industry to produce, extract and refine metals from various feed materials. However, raw materials used to provide non-ferrous metals often contain high amounts of iron. In the presence of iron, while metals are plated at the cathode, electrowinning processes produce corrosive and highly oxidative ferric ions at the anode that are harmful for the process sustainability. In fact, these ferric ions cause dramatic current efficiency loss, induce high maintenance expenditures to limit the corrosion of devices and it results in the formation of impure and dendritic deposits on the cathode. Consequently, the management of iron in electrodeposition process became a major issue in non-ferrous metals production. Actually, numerous methods have been developed to limit the ferric ion concentration in the electrolyte or, at least, to limit its harmful effect. Many methods aim to limit the iron(III) concentration in the electrolyte, generally by coupling electrowinning to extraction process such as solvent extraction (SX) (Bender & Emmerich, 2015), ion exchange (IX) (Gula, Dreisinger, & Horwitz, 1996) or cementation (Kust, 1979) processes to remove ferric ions. Other routes consist of (i) using the ferric ions oxidant properties to leach raw materials, either directly in the electrolytic cell (Fanta & Tributsch, 1975) or through a secondary circuit (Cain, 1950), or (ii) reducing ferric ions through periodic reversal of direct current to enhance the formation of Fe2+ (Loutfy & Bharucha, 1980). On the other side of the spectrum, papers discuss methods to valorize the iron from by-products of the non-ferrous metal industry, that generates vast quantities of iron containing wastes (A. Agrawal, Sahu, & Pandey, 2004). Many studies on iron electroplating and electrolytic iron production from ores have been carried out (Cain, 1950; Mostad, Rolseth, & Thonstad, 2008), but very few have been conducted on waste or by-products. Therefore, we propose to build on the previous literature review to develop a process for the production of electrolytic iron from by-products.INTRODUCTIONNon-ferrous metals and their alloys are used in a large variety of applications. Aluminum and titanium are used for their strength, light weight and corrosion resistant properties in structural applications. Copper has been used in various applications requiring high thermal and electrical conductivity, as kitchen products and electrical wires. Nickel and zinc are commonly used as plating materials; nickel offers a wide range of working temperature and zinc is used for steel plating. Gold, silver, and platinum group metals are used in electrical/electronic applications, jewelry and chemistry as catalysts."

Jan 1, 2016

By Bertrand Wolfman, William E. Stanley

"This paper reviews the traditional mine accounting systems, including ""custodial accounting"" and unit costing, and then suggests that the use of flexible budgets represents a more suitable method of reporting costs in order to assist the mine manager in improving productivity. Examples of various applications are given to show that the result is a clear reporting structure.Custodial Accounting is Emphasized in Traditional SystemsTraditional mine accounting has been mainly concerned with the accuracy of financial reporting to ""head office"" for the use of the directors and the company's bankers and shareholders. This is often called custodial accounting and it represented the main purpose of accounting when first developed in Europe hundreds of years ago. This important development permitted the establishment of enterprises which were separated from their owners because they could rely on accurate financial reports of management's stewardship.As custodial accounting is fairly broad and historical in nature, it is often not very useful to the mine manager for ongoing monitoring of performance of mining, milling, maintenance, and other support and staff groups. In spite of the considerable investment in accounting staff and computer support, many accounting systems have not been upgraded so that they accurately reflect workplace performance on a weekly or monthly basis.Budgets are Often FixedMany mines today also still emphasize fixed budgets. Thus, the mine plan which is set in the fall of one year is converted to a monthly tonnage and detailed dollar budget for periods of up to sixteen months in the future. The only certainty in this plan is that actual events will differ; timing, mix of mining methods and production volumes will differ on a monthly basis.Unfortunately, the fixed budget has no capability to reflect these operational changes. It is frozen for the full year. The result is that actual results will inevitably be compared to an outdated target."

Jan 1, 1982

By Juergen Antrekowitsch, Stefan Steinlechner

"Waelz oxide from steel mill dust recycling is usually sold to the primary zinc industry, where it is first charged to the roasters to eliminate the remaining fluorides and chlorides. This limits the overall amount of secondary materials which can be used because of different operating problems in the roasters. Another option, in the case where the halides are low, would be direct leaching with low or medium concentrated sulphuric acid. Unfortunately, because of the carryover of some steel mill dust, iron is also present in the Waelz oxide, reaching contents up to 5 wt.%. Since the objective is to treat the solution more or less directly by electrowinning, with only a few simple preliminary purification steps, iron in the solution is a very important factor. Various trials have been done to investigate the dissolution behavior of the iron contained in the Waelz oxide. Although the zinc extraction should reach a maximum, all other elements, especially iron, should be low. This paper describes the results of our research in this area and offers possible options for Waelz oxide utilization. There is also a focus on how other elements, present in the material, influence the dissolution behaviour of zinc and iron, and whether a loss of zinc is unavoidable, if low iron dissolution is required.INTRODUCTION One of the most important secondary zinc resources is the zinc oxide originating from steel mill dust recycling. For the treatment of high zinc containing steel mill dusts, the Waelz kiln process is the so called “best available technology” and it dominates the industry, with roughly a 90% market share. The product Waelz oxide contains mostly zinc oxide, but it also contains lead compounds and halides due to evaporation with the zinc. In addition, it contains iron and some slag compounds due to mechanical carry-over. The presence of halides limits the use of the material as an alternative concentrate for primary zinc electrowinning. Such halides can be reduced to a certain extent by washing and/or solvent extraction (see following chapter). Although lead is not troublesome and theoretically represents a second recoverable valuable metal, iron is unwanted and causes additional problems during leaching. Even though Waelz oxide is generally a highly welcome input material in primary zinc metallurgy, due to its high zinc content, it still contains halides, and in the majority of cases, the oxide must first be treated in a roasting process. Different circumstances, like accretion formation because of the lead and halogen compounds as well as unwanted cooling effects in the roaster, limit the amount of Waelz oxide which can be substituted for the primary concentrate. Another, even more limiting factor, is the allowable concentrations of chlorides and fluorides in zinc electrowinning, the last step in the primary zinc processing route (Ruetten, 2011)."

Jan 1, 2016

By James Stenhouse

Abstract The aqueous oxidation of pyrite in caustic solutions under oxygen pressure was investigated by measuring that effect of reaction variable on oxygen consumption by the reactions. From the results of this investigation, a model for the process has been proposed. In this model, sulphur diffuses as a positive ion through an oxide layer which forms on the sulphide particles and is then oxidized to sulphate ion. Iron is oxidized by substitutional diffusion of oxygen atoms into the oxide layer. The effect of most reaction variables on the rate of oxygen consumption can be explained with this model. Introduction Recent investigations (1,2,3) have shown that certain sulphide ores can be readily leached by agitating the ore in the form of a pulp under pressure in the presence of oxygen. Since very little was known of the mechanism of this oxidation, a programme of investigation was inaugurated in 1949 in the laboratories of the Department of Mining and Metallurgy of the University of British Columbia. Financial support for the investigation was received from the National Research Council in the form of student grants and bursaries, from the Canadian Liquid Air Company, Limited, and from the Consolidated Mining and Smelting Company of Canada, Limited. The first objective was to devise a technique to study the primary oxidation reactions in aqueous solutions and to apply the technique to a detailed study of the oxidation of pyrite in caustic solutions.

Jan 1, 1952

By P. O. Rag, Daniel E. Walsh

"Gravity concentrators are evaluated either in closed or open circuit. The process developed by MIRL employs the use of neutron activated gold (/98Au) and radiation detection circuits which monitor the concentrator's product pulp streams. Concentrator recovery is determined from the ratio of the number of gold particles detected as passing into the concentrate to the total number of gold particles detected over all monitored pulp streams. This system eliminates the experimental errors introduced by sampling, sample reduction, and assaying and allows recovery to be evaluated for gold particles of specific sizes, shapes, and flatness. In addition to allowing for a more accurate and detailed recovery analysis, this process significantly reduces the time and cost required for unit evaluation when compared to other gold recovery analysis procedures. This system enjoys its greatest utility where a large number of tests are to be run in order to evaluate a concentrator over a variety of operational settings, i.e. factorial designs, and allows accurate testing of concentrators operated in closed circuit systems.IntroductionThe surge in gold prices of the late 1970s and early 1980s was followed closely by a renewed interest in gravity concentration processes, especially in concentrators claiming efficient recovery of fine placer gold. Cones, spirals, spinning bowls, jigs and cyclones are all considered potential fine gold concentrators. Fine gold, in this context, is defined as not only that gold finer than 250 um (60 mesh""), but also coarser gold, whose low shape factor may decrease its recovery by conventional, large-scale sluicing operations.Adoption of fine gold concentrators by the Alaskan placer milling industry was retarded by the lack of reliable, accurate, and reproducible data on concentrator efficiency with respect to fine placer gold recovery. In most cases, concentrator performance was based on a limited number of tests run on placer material, about which only slight knowledge of gold size and shape characteristics existed. In order to be prepared for the resurgence of interest in fine gold concentrators, which will follow the next upturn in gold prices, a detailed study of the fine gold recovery characteristics of gravity concentrators needs to be conducted."

Jan 1, 1986

By Youngsoo Song, Hyunjung Kim, Junhyun Choi, Siyoung Q. Choi, Gahee Kim

In this study, for the first time, to confirm the effect of bacterial growth phase on the malachite flotation were investigated in a well-controlled Hallimond tube system. The test results showed that the bacteria in the stationary phase exhibit two-fold greater floatability than those in mid-exponential phase. To understand the observed flotation behavior, complementary cell characterization tests and cell attachment tests were conducted. Interestingly, the bacteria at both phases exhibited similar surface properties as well as almost identical amount of cells attached onto the malachite, suggesting that the growth phasedependent flotation behavior cannot be attributed to the variation of cell surface properties and the extent of cell adsorption. On the other hand, cell detachment tests revealed that the amount of cells detached from the malachite surface is greater for the mid-exponential phase than the stationary phase due to the higher fluid drag applied to the cells at the mid-exponential phase, which was explained by the differences in the size and shape of attached bacteria onto the malachite surface. These morphological characteristics were found to cause the bacteria of mid-exponential phase to be separated highly sensitive and easy from malachite surface due to the fluid flow. Second, scale-up selective bioflotation tests were carried out in a 1 L Denver cell in malachite–silica binary mixture systems. Through the tests, we optimized the cell concentration and the malachite fraction in the feed. Overall, high malachite selectively was observed under optimized conditions (both recovery and grade showed more than 90%). The trend was in agreement with classical DLVO interaction energy profiles, which show the relative magnitudes of the adhesive forces between the mineral and the attached cell under equal hydrodynamic conditions.

Jan 1, 2016

By L. I. Kiss, S. Perron, D. Toulouse, S. Poncsák, A. Perron

Bubbles play an important role in many industrial processes. In a Hall-Heroult cell, used for aluminum production, bubbles contribute to induce flow in the cell. The induced flow is important for the thermal balance of the cell as well as for the distribution and dissolution of the alumina. The existence of the bubble layer does not have advantages only. It increases the voltage of the cell and causes deformation along the cryolite-molten aluminum interface. The role of the anode inclination in the behaviour of the bubble layer as well as in the hydrodynamics of the bath is not clearly understood. In this work, the effect of the anode inclination angle on the bubble driven flow is studied in an industrial scale air-water model. The inclination angle is varied up to 5° from the horizontal. The instantaneous flow field is captured by Particle Image Velocimetry (PIV) system. The mean velocity fields were calculated by ensembleaveraging the instantaneous velocity fields measured at different time. The existence of the counter-flow in the interpolar space and the vortex in the side channel has been confirmed. Furthermore it has been observed that the effect of anode slope on the velocity field is weak.

Jan 1, 2006

By Carlos Palacios M., Brian K. Townley

"Abstract - The mainland Aysén region of Chilean Patagonia (44°15' - 47°30'S) is a representative segment of the South American active continental margin, distinct with respect to northern and central Chile. Mineralization consists mainly of polymetallic deposits, with important Zn-Pb mines and more recently discovered Au-Ag deposits, unlike the central Andes, which are dominated by Cu mineralization. On a regional scale, rocks may be grouped in four main map units: 1) the Paleozoic metamorphic basement; 2) upper Jurassic-Cretaceous calc-alkaline volcanic and marine sedimentary rocks; 3) the Patagonian batholith, and 4) upper Cretaceous to Miocene basalts and marine and continental sedimentary rocks. The upper Jurassic-Cretaceous rocks and the Patagonian batholith formed in a volcanic arc and back-arc setting superimposed on the Paleozoic metamorphic basement.Based on geographic location and geologic and tectonic setting, ore deposits in this region are assigned to three groups, from south to north: El Faldeo, Fachinal, and El Toqui. The El Faldeo group (south of 47°05'S) includes upper Jurassic Zn-Pb skarn and associated polymetallic massive sulfide vein deposits locally overprinted by Au-rich epithermal mineralization, hosted by volcanic and sedimentary rocks and/or by rocks of the metamorphic basement. The Fachinal group (46°05' - 47°05'S) consists of volcanic-hosted lower Cretaceous Au-Ag epithermal deposits, except for the Mina Silva and Manto Rosillo deposits, which are metamorphic basement-hosted Zn-Pb skarns. The El Toqui group (44°30' - 46°05'S) comprises lower Cretaceous Au-rich Zn-Pb skarns and associated polymetallic veins, as well as Au-Ag-rich epithermal deposits, hosted by volcanic, intrusive, and marine sedimentary rocks. Galena lead isotopic signatures for each deposit group indicate a decreasingly radiogenic trend from south to north, suggesting different lead sources or differences among underlying crust. Three metallogenic provinces and two metallogenic epochs are proposed for the Aysén region: the El Faldeo metallogenic province of Late Jurassic age; and the Fachinal and El Toqui provinces of Early Cretaceous age. Résumé - La partie continentale de la région d’Aysen (Patagonie chilienne, 44°15' - 47°30'S), est unsegment représentatif de la marge continentale active d’Amérique du sud, différent des segments du nordet du centre du Chili. La minéralisation, qui consiste essentiellement en des dépôts polymétalliques, avec d’importantes mines de Pb-Zn, et des dépôts d’Au-Ag récemment découverts, différe de celle des Andes centrales où domine la minéralisation cuprifère. A l’échelle régionale, les roches peuvent être regroupées en quatre unités cartographiques principales : 1) le socle métamorphique paléozoïque, 2) les roches volcaniques calco-alcalines et les sédiments marins du Jurassique supérieur-Crétacé, 3) le batholite patagonien, et 4) les sédiments marins et continentaux ainsi que les basaltes du Crétacé supérieur-Miocène. Les roches du Jurassique supérieur-Crétacé et le batholite patagonien, formés dans un contexte d’arc volcanique et d’arrière-arc se superposent au socle métamorphique paléozoïque.Fondé sur la localisation géographique ainsi que sur le cadre tectonique et géologique, les dépôts de minerais de cette région se répartissent en trois groupes, du sud au nord, El Faldeo, Fachinal et El Toqui. Le Groupe El Faldeo (sud de 47°05'S) contient des skarns à Pb-Zn du Jurassique supérieur associés à des veines de sulfures massifs polymétalliques, localement recoupées par des minéralisations épithermales, riches en Au, et contenus dans des roches sédimentaires et volcaniques et/ou dans des roches du socle métamorphique. Le Groupe Fachinal (46°05' - 47°05'S) consiste en des dépôts épithermaux Au-Ag, se trouvant dans des roches volcaniques du Crétacé inférieur, excepté pour les dépôts de la Mine Silva et Manto Rosillo, où des skarns à Pb-Zn, se trouvent dans le socle métamorphique. Le Groupe El"

Jan 1, 1999

By Akira Miura, Katsuyuki Sato, Yuken Fukano

JX Nippon Mining and Metals Corporation has developed the JX Iodine Process, which is an innovative and patented copper-leaching process for low-grade primary sulfide ores. This process consists of the irrigation of ferric iron and a low concentration of iodide solutions. One-meter column leaching tests were conducted on ore samples from two different mines. At the end of experiments, the total copper recovery exceeded 70% for Sample A and 50% for Sample B with the iodine method, which was significantly higher than that with conventional ferric leaching of 14% for Sample A and 20% for Sample B. To elucidate the reason for the JX Iodine Process effectiveness, cross sections of leached residues were studied. Reaction products were confirmed around chalcopyrite even in the central area of particles in Sample A, however, reaction products were recognized at a depth of only 1 mm from the ore rim in Sample The resistance of Sample A to the leachate appeared to be lower than that of Sample B because Sample A had a high permeability and porosity, whereas Sample B had been affected strongly by a potassium alteration. No reaction products were visible on conventional leaching samples, even at the ore surfaces. INTRODUCTION Hydrometallurgical copper leaching (heap leaching or dump leaching) has been used extensively for copper recovery from oxide and secondary-sulfide ores, but not for primary copper sulfides, which contain mainly chalcopyrite as copper minerals. Although they are major resources of copper, primary copper sulfides are difficult to process because of their refractory nature. Extensive leaching studies have been carried out to leach primary copper sulfides (chalcopyrite), including biological and chemical, using a variety of oxidants and additives to enhance copper recovery. Watling (2013) reviewed acid-chloride-oxidizing agents with chalcopyrite. Abdollahi et al. (2015) tested silver as a catalyst for bioleaching with a chalcopyrite-bearing molybdenite concentrate. Hiroyoshi, Miki, Hirajima and Tsunekawa (2000) found a specific redox-potential zone for high-speed chalcopyrite leaching by controlling the ratio of ferric and ferrous iron. However, no ambient-temperature economic process has been developed for leaching primary copper sulfide, which usually has a low copper grade.

Jan 1, 2019

By Gordon Sparks, Lyle Kajner

"An often over-looked component in the assessed value of a mining property is the value derived from the ability of the operator to limit financial losses during adverse economic times (i.e. low market price, high energy prices, etc.) by suspending operations. Overlooking the value of this type of operating flexibility when conducting mine investment analysis may negatively bias the risk profile for the investment by over estimating the investment's downside potential, thereby effectively undervaluing the investment. This paper illustrates the nature of the value of operating flexibility and discusses how it may be explicitly quantified within the context of conducting stochastic mine investment analysis. IntroductionMining properties are evaluated using an array of techniques ranging from simplistic non-discounted payback calculation s to sophisticated, discounted-stochastic simulation. Stochastic simulation analysis is perhaps the most robust mine investment analysis technique as it not only provides an estimate of the expected value of the property, but also quantifies the associated risks (for examples of stochastic mine investment analysis, see: Billingsley and Yaychuk, 1986; Gentry and O'Neil, 1984; Munro, 1977; or Harris, 1970).The quantification of risk is important as it provides the necessary yardstick required to allocate the corporation's resources efficiently. Resources are said to be allocated efficiently when the corporation's expected long-term financial reward is maximized while at the same time minimizing its risk (see Hertz, 1968; or Markowitz, 1952 for in depth discussions on efficiency as it relates to investment policy). The efficient allocation of resources should be the objective of any rational corporation. Therefore, rational corporations should employ stochastic evaluation techniques when screening their investments."

Jan 1, 1992

By F. R. Archibald

IN a recent paper on Roasting of Beattie Concentrate (1), the importance of controlling the temperature, and the sulphur dioxide concentration was pointed out. It is the purpose of the present paper to present further information by which the most satisfactory conditions for roasting are more specifically defined. Incidentally, a method of illustration is developed for representing roasting curves on a three-dimensional diagram. The primary purpose of this investigation, as in the case of the earlier work, was the search for information that would be of practical value in improving plant operation and gold recovery. For this reason, emphasis is laid on the regulation of essential variables and on definition of their optimum values and limits for maximum gold recovery in the subsequent cyanidation process. Good roasting is considered at least as much an art as it is a science, and, in this light, theoretical consideration of the nature and sequence of the chemical reactions involved is of secondary importance. The presentation which follows includes a series of graphical illustrations, an interpretation of the graphs, some theoretical considerations, and a description of laboratory technique.

Jan 1, 1940

By P. Wanjara, M. Xiao, M. Jahazi, C. Poon

Using a robotic 4kW Nd:YAG-laser system, Inconel 718 (1 mm sheet) was welded with and without filler wire to investigate the effect of processing parameters, including power input and welding speed, on the weld geometry, microstructure and mechanical properties. By means of both nondestructive testing and microscopic examination, the weld quality was studied to determine the nature of the welding defects (porosity, cracking and bead shape) over the processing range of 3-3.5 kW for the power input and 4.5-6 m-min-1 for the welding speed. Application of the design of experiment methodology permitted the examination of the relationship between the process parameters and mechanical properties, from which the optimized laser welding conditions could be determined for joining Inconel 718. In particular, the research results indicate that Nd:YAG-laser welding technology can achieve defects free, mechanically sound welds with narrow fusion and heat effected zones.

Jan 1, 2006

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By John Porritt, Alain Dorval

"TioMin Resources Inc. is evaluating the feasibility of exploiting the heavy mineral sands deposit at Natashquan on the north shore of the Gulf of St-Lawrence, Quebec. TioMin holds the exploration rights to 180 square kilometres, on which 1.6 billion tonnes of sands grading approximately 6% heavy minerals were outlined. The heavy minerals of value include magnetite, ilmenite/hematite, garnet, and zircon. An important part of this evaluation is the development and testing of a mineral separation flowsheet. Under a comprehensive mandate from TioMin, the Centre de recherches minerales (CRM) provided technical assistance to build and operate an on site primary concentrator pilot plant. This plant produced a 93 tonne concentrate, providing over 60 % heavy minerals. This concentrate was shipped to the CRM pilot plant in Quebec City. It was used for further flowsheet testing and for preparation of products and concentrates of heavy minerals with regard to marketing possibilities. This paper presents the flowsheet developed to produce these concentrates.IntroductionIn late 1992, an 11 tonne bulk sample of sand was collected from within the mineralized zone of the Natashquan deposit. This sample was processed over conventional spirals and wet tables at the pilot plant facilities of the Centre de recherches minerales (CRM) in Quebec City. A primary concentrate was produced, from which several 20 kg samples were forwarded to five research laboratories in North America and in Australia. Their tasks were to determine the mineralogical composition of this concentrate and the potential for recovery of marketable minerals from the heavy mineral sands. Satisfactory results obtained from this approach encouraged TioMin to proceed with a more detailed pilot plant program."

Jan 1, 1995