Search Documents

By J. A. Finch, G. Labonté

"A long-standing objective has been to obtain interpretable measurements of the oxidation-reduction potential in mineral slurries. For this purpose several sensing electrodes (black platinum wire, platinum foil and spiral, gold foil and spiral, and sulphide minerals such as chalcopyrite and galena) were investigated to determine their response to the presence of sulphide minerals in the pulp, and to the addition of reagents commonly used in flotation. The observed discrepancies between the electrodes may be explained using a combination of the classical mixed potential model for complex solutions and the probability of contact between the mineral particles and the sensing electrode. It is shown from laboratory testwork that gold spirals are preferred over platinum electrodes. Finally, some of the practical aspects of using the electrochemical measurements in a plant environment are discussed.IntroductonThe interpretation of flotation of sulphide minerals in terms of electrochemical (electron transfer) processes has brought new possibilities for process control of selective flotation. Investigations on massive and compacted particulate bed electrodes have shown that the flotation of a given mineral in the presence of a collector can be controlled by the potential induced on the mineral surface. Also, phenomena such as collector less (self-induced) flotation, activation by heavy metal ions, and natural selectivity sustained by galvanic coupling during flotation might also be controlled by electrochemical means.The technique for measuring electrochemical potential in slurries is an adaptation of that used for solutions. The measurement of the oxidation-reduction potential of a solution (ORP , Redox, Eh) is usually carried out by immersing a noble metal electrode (platinum, gold or silver) and a non-polarizable reference electrode: Standard Hydrogen Electrode (SHE), Standard Calomel Electrode (SCE), or silver/silver chloride (Ag/AgCl) in the solution. (The abbreviation Eh implies the SHE is the reference electrode.) The potential difference between the two electrodes is measured using a high impedance electrometer. ASTM standard D 1498-76 (revised 1981)(1) covers the practical details of such measurements; however, it does not deal with their meaning either in complex solutions or in mineral slurries ."

Jan 1, 1988

By G. W. H. Norman

The surficial Archæan rocks of the southern gold belt of western Quebec are constricted near Kewagama lake by granite masses to the north and south. This divides the belt into natural eastern and western parts. This paper deals with the eastern part, extending from Malanie to Haig township. In this section the Keewatin-Timiskaming rocks have a length of about 70 miles and end abruptly against garnetiferous gneisses of the Grenville terrain. In the western half of the section where exploration has been under way since the early twenties, there are sixteen mines that are or have been in operation, and eleven prospective mines. In the eastern half where exploration has been carried on since the early thirties, six prospective gold mines are under development, one· of which, Louvicourt Goldfields, is at the initial production stage. Of the sixteen properties in the western half that are operating or have operated, all, except the Golden Manitou, which is a base metal mine, and the old Green Stabell from which there was a small production of copper, produce gold. Of the eleven prospective mines in the western half nine have gold. New Bidlamaque has gold and copper and one, East Sullivan, has copper-zinc ore. Since production began in 1927 gold, silver, zinc, copper, and lead having a total value of about $10,000,000 have been produced from the mines of the eastern section of the southern gold belt of western Quebec.

Jan 1, 1954

By G. Diaz

Técnicas Reunidas (TR) has been involved for over 30 years in the development of process technologies for the recovery of zinc from different primary and secondary feed materials, such as the ZINCEXTM process. Because of the complexity of the feed mineral resources, solvent extraction (SX) is an invaluable technique to concentrate and purify zinc solutions. When applied to a pregnant leach solution, solvent extraction can produce an extremely high quality zinc electrolyte, suitable for obtaining SHG zinc ingots, after electrowinning and melting and casting processes. However, the high affinity of most organic extractants for Fe(III) poses a serious problem, which may adversely affect the zinc extraction process. Different methods may be applied to deal with the negative effect caused by Fe(III). An acid regeneration step and electro-reduction stripping have been considered as the most viable techniques to remove the iron from the organic phase. This paper describes some findings of Técnicas Reunidas in the area of zinc solvent extraction, especially on removing Fe(III) from the organic phase.

Jan 1, 2006

By P. Hale

"The trend to drives of more than 10,000 hp on large-capacity ball and autogenous mills for increased operating efficiency has been limited by factors in the conventional drive system. A solution to this problem, using modern developments in static converter technology, is the concept of driving the mill directly without gearing using a low-speed, low-frequency synchronous motor with a cyclo-converter power supply.This paper presents various practical arrangements of mill and low-speed motors giving the specific advantages of each system. The means of controlling inrush currents on starting and of spotting by the use of variable-frequency control are outlined in general form. Several gearless ball mill drives are scheduled for start-up in European cement plants and further orders have been placed."

Jan 1, 1970

By J. Farrell

The Canadian government ratified the Kyoto Protocol in December 2002 and, prior to ratification, committed to equitable distribution of the burden of implementation. The Federal government's Large Final Emitters group is working with industry to develop covenants that will consider the unique nature of the company's operations and not unreasonably burden any one sector or company. Ensuring equitable distribution must consider local, national and international issues. From a Canadian iron ore producers perspective, the fact that most of the iron ore production in the world is in countries that have no Kyoto commitment is a critical issue. Another issue unique to this sector is the increased addition of fluxing agents in iron ore pellet production which has shifted some process related greenhouse gas emissions from steel producers to iron ore producers. While the objectives of the Kyoto Protocol are primarily environmental, the economic implications for Canadian industry are not trivial. For decades Canadian companies have been actively improving energy efficiency and reducing greenhouse gas emissions to maintain a global competitive position. Production of iron ore pellets is an energy intensive process and the Iron Ore Company of Canada (IOCC) is the largest Canadian producer. In 2002 IOCC identified energy and Kyoto Protocol implementation as critical risk factors for their organization and appointed a full time Energy Manager. In January 2003, IOCC initiated a comprehensive process for identifying energy cost reduction opportunities and established an Energy Master plan. This process included:

Jan 1, 2004

By M. Leroux, C. J. Martin, S. R. Rao, J. A. Finch

"The effect of nitrogen on the flotation separation of sulphides from complex ores from Brunswick Mining and Smelting (New Brunswick) and Mattabi Mines (Ontario) was investigated. The most significant finding was enhanced pyrite floatability after as little as 3 minutes nitrogen conditioning. This was used in a novel sphalerite/pyrite separation process developed on the Brunswick ore. After aeration and Cu/Pb bulk flotation in air using xanthate the slurry was nitrogen conditioned, xanthate added and the pyrite floated in nitrogen. As an example up to 70% pyrite recovery with about 20% sphalerite recovery was achieved. Sphalerite was recovered from the pyrite tailings and the pyrite concentrate by copper-activation, raising the pH to 10 and floating in air. About 65-70% recovery at 35-40% Zn grade was achieved compared to 25% Zn grade by the conventional route. The process offers a promising alternative to current practice which seeks to depress pyrite at all stages. A possible mechanism of the effect of nitrogen is presented. INTRODUCTIONUse of gases other than air in froth flotation has been reported from time to time. [Podobnik and Shirley, 1982; Lin and Metzer, 1975]. Of all the gases, nitrogen would appear to hold the greatest practical promise because of its easy availability and chemical inertness. It is used in froth flotation in chalcopyrite-molybdenite separation [Redfearn, 1983]. The use of nitrogen in polysulphide chalcopyrite. this case is mainly to reduce the oxidation of a compound (Nokes reagent) used as a depressant for There is no reported use of nitrogen in the flotation of other sulphide minerals."

Jan 1, 1988

By Mark Liskowich

When is it the proper time to initiate engagement with various stakeholders, including Indigenous communities? This paper will demonstrate what stage of a project’s evolution is the appropriate time to initiate a stakeholder engagement plan. It will look at aspects to consider when identifying the communities to involve. It will describe the contents of a Stakeholder Engagement Management Plan as well and touch on how tried and true options analyses, such as a Multiple Accounts Analysis can be used to inform the results of the engagement, guide the development of your project and clearly document the engagement process. It will illustrate the benefits of initiating engagement at the appropriate point in your project’s schedule, and the limitations of doing so too early and at later stages of the project engineering. The benefits of this approach can be realized within any legislative Jurisdiction including the Canadian Environmental Assessment Act 2012 and Canada’s new Impact Assessment Act.

Jan 1, 2020

By Leonardo F. Trivino

Despite the significant economical and safety implications of poor blasting practice in mining and quarrying operations, the default practice in many large operations, including both design and control, is considerably below standard when compared to other engineering disciplines. Blast dynamics includes a number of complex phenomena, such as the generation, propagation and interaction of stress waves, the expansion of high pressure, high temperature gases from the explosive components, and their combined effects upon the rock mass, including fracturing, fragmentation and displacement. In order to tackle this non-trivial problem, a combined finite and discrete element software (Y-code) capable of accounting for the dynamic behaviour of stress waves, simulating fracturing processes and modeling the expansion of gases is under development. The constitutive models used in this particular software are fundamentally simple, however, non-linearity and chaotic behaviour result as natural consequences of the interaction of relatively simple processes and mechanisms, such as propagation of stress waves in the immediate vicinity of the exploding borehole, and the creation and propagation of fractures. Advances on its development and comparisons with experimental data show realistic propagation of stress waves and fracture networks.

May 1, 2013

By David Morrison

Our present longwall problems in Cape Breton can be grouped under five main classifications. These are: (1) Roof control on the face and on the main roadways leading thereto. (2) Transportation of coal along face and levels. (3) Mechanical loading at the face. (4) Safe method of conducting and applying power at the working faces. (5) Dust nuisance. The usual layout for longwall operation in Cape Breton is to have three, and sometimes four, faces in line with each other, the length of face being from 400 feet to 500 feet (see Figure 1), and producing between 425 and 500 tons per face. Each wall is serviced by a well constructed roadway for transportation of coal, men, and materials, and is operated as an independent unit. Each wall works under a regular cycle of operations: first, cutting and boring; second, drawing hardwood chocks, building midwalls, and shifting panlines; and third, loading. The present method of roof control and operation of longwall faces has developed through trial and error since the commencement of longwall miring in Cape Breton. The basic method of roof control in all longwalls in Cape Breton is: rigid support of the roof in the immediate vicinity of the working faces by hardwood blocks, as shown in Figure 2, accompanied by a cushion support furnished by continuous midwalls, 12 feet wide, constructed of stone obtained from the waste and spaced at 50-foot centres. These midwalls are kept forward to within 4 feet to 10 feet of the working face and allow a gradual subsidence of overhead strata, thus preventing any sudden break at the working face.

Jan 1, 1947

By S. Balideh

A good understanding of the behavior of broken rock helps to make more informed decisions regarding slope stability and waste dump issues in mines. The cohesion coefficient of rock has little influence on the strength of broken rock; therefore, a criterion based on friction and cohesion of intact materials does not provide an accurate analysis for the strength of broken rock. This paper illustrates the effective strength of broken rock through a brief literature review about failure of intact rock and rock masses. The complete stress- strain curve and some important points of residual strength of rock are summarized in this paper.

Jun 1, 2012

By W. R. Middagh, R. M. Garvey

"Phosphate rock is shipped by boat from Florida to Vancouver, B.C., where it is unloaded and stored in a 50,000-ton silo. It is shipped from Vancouver in 100-ton hopper cars in 80-car trains to Fort Saskatchewan. Both the ship and the hopper cars are on a back-haul with potash. The rock cars are unloaded at Fort Saskatchewan at a rate of approximately 4 cars per hour. The rock is stored in three concrete silos, 40 ft in diameter by 110 ft high, which hold 18,000 tons of recoverable rock with 2,000 tons dead space. The rock is reclaimed from the silos by gravity and fed to the phosphoric acid plant by remotely operated conveying equipment.Problems encountered in the operation include scheduling the rock shipments, contamination of the rock with potash, and handling the 80-car trains both in Vancouver and Fort Saskatchewan."

Jan 1, 1968

By D. Runnels, A. Allaire, J. Fournier, Y. Sylvestre, F. Robichaud

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

By George P. Demopoulos

In this paper the author will provide an overview of over 20 years of research & developments in the area of hydrometallurgical arsenic immobilization that culminated recently in the industrial implementation of the atmospheric scorodite process. The paper will consider various aspects of arsenic fixation in the non-ferrous metal industry from the iron-arsenic co-precipitation process employed to arsenic-bearing effluent solutions; to autoclave processing of arsenical copper and gold feedstocks and the fate of the in-situ formed iron sulphato-arsenate precipitate phases; the precipitation and stability of scorodite; the possible stabilizing role of mineral phases like yukonite, and the development of "scoroditeplus" processes employing novel encapsulation strategies. Emphasis is placed on the characterization and long-term stability of the various forms of arsenic-immobilized phases under either oxic or anoxic conditions over a wide pH range and the establishment of critical links between process parameters and hazardous material stability, contributing thus to advancement of new generation safe and sustainable waste management technologies.

Jan 1, 2014

By Zou Lisheng

The culture of safety is very important to coal mining production. About 90% of mine accidents are caused by human error. This paper analyzes the status of China?s coal mining accidents, and accident cause. This paper explains the concept of safety culture, the value of safety culture, as well as the relationships between safety culture and safety behavior, and between safety culture and science and technology. The paper proposes the model of safety culture and the ways to enhance safety culture of coal enterprises. Safety culture and safety production is closely related and are significant to the improvement of mine safety situation in China.

Aug 1, 2013

By C. Liu

Corrosion behavior of the stir zone in a friction stir weld of dissimilar A12024/AZ31 alloys was investigated in the immersion test in distilled water (pH=6) for different times. Microstructures and the distribution of chemical elements were analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Due to the difference in the corrosion potentials between A12024 and AZ31, the AZ31 alloy constituent in the stir zone was susceptible to the corrosion attack in the distilled water. The corrosion attack was found to occur in the narrow region of the AZ31 alloy adjoining the A12024 region, where there was a low ratio of anode-to-cathode surface area. The corrosion attack became more severe in the AZ31 alloy regions with increasing immersion time. The A12024 alloy region in the stir zone of the weld was protected by cathodic reactivity due to sacrificial anode AZ31 alloy.

Jan 1, 2007

By Louise Laverdure

The Canadian mining sector has to be innovative and invest in the development of sustainable mining technologies to maintain its international leadership. Natural Resources Canada (NRCan) collaborated with the Canada Mining Innovation Council (CMIC) to define the Green Mining Initiative (GMI) and in order to focus its R&D activities on industry and other stakeholders? needs. The GMI was launched in 2009 to spur innovation in the mining sector and further enhance its environmental performance. The initiative, led by CANMET- Mining and Mineral Sciences Laboratories (MMSL), takes a holistic approach looking at the entire mining life cycle, from design to closure and beyond, through four innovation and research pillars: ? Footprint Reduction, ? Innovation in Waste Management, ? Mine Closure and Rehabilitation, and ? Ecosystem Risk Management. The Canada Mining Innovation Council has also been creating a new initiative on Sustainable Mining, which will bring further focus to environmental aspects of mining, and engaging wide range of research providers to develop research programs complementary to GMI goals.

May 1, 2011

By K. Koyama

As a study to establish a new energy-saving copper recycling process, the copper deposition at a cathode and oxidation of copper(I) at an anode from ammoniacal alkaline solutions containing Cu(I) or Cu(II) were investigated in order to examine the feasibility of electrolysis in this solution.. The current efficiencies were greater than 95% in the current density range of 200 to 1000 A m-2. The current efficiency decreased with the increasing Cu(II) concentration and temperature. In the batch-type electrolysis at the anode, during the initial stage, the current efficiencies were 100%, and the anode potentials ranged from 0 to 0.15V vs. SHE at a current density of 100 A m-2. During the subsequent stage, the current efficiency decreased with time, and the anode potential was around 1.35V vs. SHE where oxygen evolution at the anode surface was observed. As a result, the present electrolytic method can be the core technology in the said copper recycling process.

Jan 1, 2007

By Michel Jebrak, Claude Bellehumeur

Regional and orientation geochemical stream sediment surveys were carried out by the Quebec Department of Energy and Resources in southwestern Quebec, over a part of the Mont Laurier Terrane of the Grenville Province. The area contains some small stratiform zinc deposits. The response of Zn mineralization to geochemical surveys is weak; the known mineralization is not dermed by anomalous samples and consistent patterns. This study uses a technique that increases the geochemical signature of Zn mineralization in filtering out geochemical background components related to lithologies and surficial conditions. The background variations were modelled using principal component analysis, and the filtering technique consists of the partial reconstruction of the data matrix from results of principal component analysis. The filtering procedure considerably enhances the Zn anomalies located in the catchment basins of Zn deposits, and defines some new anomalies in proximity to the marbles of the Mont-Laurier Terrane, the principal metallotect of Zn mineralization.

Jan 1, 1993

By K. M. Ed

AN explosive is a solid or liquid substance which, when fired by some means, changes into a gaseous product occupying a volume very much greater than its original volume. The great speed at which this change takes place causes the explosive to exert a sudden blow on adjacent material. It is this action which is effective in blasting operations when the explosive, confined in a shot-hole, is fired. All explosives are similar in one respect, in that the change into the gaseous state is accompanied by the production of hot gases or flame. This results from the rapid combustion of the solid or liquid ingredients. Ex-plosives differ greatly, however, in the speed at which the reaction takes place. Black blasting powder, for instance, reacts comparatively slowly, hence the flame persists for an appreciable length of time. High explosives, on the other hand, react much more quickly; consequently, the flame is of much shorter duration. In 'closed-light' or 'gaseous' coal mines, the use of ordinary explosives is generally prohibited, due to their inherent ability to ignite gas or coal-dust by reason of the flame which they produce when fired. For instance, black blasting powder, which produces a flame of long duration, is not ordinarily considered safe to use in such mines; neither are ordinary dynamites, as their flames, while shorter than that of black blasting powder are, nevertheless, of sufficient temperature and duration to cause ignition of fire-damp or coal-dust. For this reason, specially formulated high explosives, called 'permitted' explosives, should invariably be used in such mines.

Jan 1, 1940

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016