Search Documents

By K. Adham

Iron chloride pyrohydrolysis (ICP) is used as an efficient way to fix iron as an oxide, for sale as a by-product or for safe disposal. Iron chloride is reacted with water at elevated temperatures to yield iron oxide and hydrogen chloride. Both the steel industry and synthetic rutile producers make extensive use of ICP. Two technologies are available for ICP: fluidized bed (FB) and spray roaster (SR). Both technologies are energy intensive. Here, fluid beds and spray roasters are compared with respect to their fuel and electrical energy consumptions. Roaster size and oxide product characteristics are also considered. Process models are prepared, using the METSIM® software, and specific energy consumptions are compared. The results will help the industry decide which technology best suits its goals and at what energy cost.

Jan 1, 2006

Abstract-This paper discusses the fundamental question, "what is an adequate sample size?" in the light of recent developments regarding parameters of Gy’s well-known formula for predicting sampling variance. New understanding of the granulometric factor, g, and the liberation factor, l, had significant impact on the results of calculations involving Gy’s equation. For the granulometric factor, justifications are given as to why nominal comminution size should always be reported as P95 (i.e., the screen size rejecting 95% of the mass). A small but important change in the model to estimate the liberation factor makes the difference between a predictive formula that works or does not. Other parameters and considerations regarding their practical implementation are commented upon in light of the author’s experience.

Jan 1, 1998

By D. J. Archambeault, A. Saigal

Substantial cost savings have been demonstrated by material design changes after initial product development. As more information about a product's operating environment becomes available to a designer, it is possible to consider a more costeffective material that still meets or exceeds the design intent, such as minimum low cycle fatigue life. This is especially true in the aircraft engine industry, where precise operating cycle data is not available until after the first engine is built and tested. A methodology for predicting estimated low cycle fatigue life has been developed to investigate potential material change candidates for an aft cooling plate. A twodimensional macromechanical finite element model (FEM) has been developed using ANSYS and used to determine the effects of varying material properties. It is shown that slight changes in density, coefficient of thermal expansion and modulus of elasticity have profound effects on component and effective stresses, and therefore, estimated low cycle fatigue (ELCF) life. Aerospace

Jan 1, 2006

By A. L. Mackie

Mine water from base metal mines is generally characterized as having high concentrations of heavy metals and low pH, resulting in the need for treatment prior to discharge to receiving waters. In this study, two high-rate clarification processes were evaluated at bench-scale: the high density sludge (HDS) process and sand-ballasted flocculation. High-rate clarification processes generate larger, denser flocs which settle more quickly than those formed in conventional flocculation processes. The HDS process uses recirculated sludge in order to seed floc formation, whereas ballasted flocculation uses microsand. Both of these high-rate processes require the addition of quicklime or hydrated lime to increase pH and allow for the formation of insoluble metal hydroxides, which can then be removed in the clarification stage. Previous research has shown that cement kiln dust (CKD) can effectively replace quicklime in conventional sedimentation processes for metals and acidity reduction to meet discharge guidelines (Mackie & Walsh 2012). CKD is an alkaline by-product of cement manufacture that has fine particle sizes and varying free lime concentrations depending on the manufacturing process. The lower solubility (i.e., free lime content) of CKD requires larger doses of material to be added to reach treatment pH targets for metals precipitation. The purpose of this study was to evaluate the treatment efficacy of high-rate clarification processes for mine water treatment, compared with conventional sedimentation, at bench-scale with conventional (i.e., lime) and novel (i.e., CKD) pH adjustment additives. Results of the study showed that all treatment processes (i.e., HDS, ballasted flocculation, and conventional sedimentation) were able to reduce target metal concentrations to well below Canadian guidelines (i.e., total zinc and total nickel < 0.5 mg/L, total copper < 0.3 mg/L) using either CKD or lime. Additionally, mine water samples treated with CKD generated lower sludge volumes than those treated with lime (i.e., 50 versus 100 mL for conventional sedimentation and 100 versus 200 mL for HDS) even with increased concentrations of solids introduced during treatment. This is most likely due to slower neutralization rates when using CKD, due to its lower solubility, as well as finer particle size. The sand-ballasted flocculation process was able to reduce final turbidity in CKD-treated samples while the HDS process did not when compared to conventional sedimentation, making the ballasted flocculation process preferable for reducing final solids concentrations in CKD-treated mine water.

Aug 1, 2013

By Baseer Abdul, Edouard Asselin

Hydrometallurgical leaching of sulfide concentrates of copper and nickel at medium temperature (150°C) produces residues that contain sulfur and iron bearing minerals and phases. During leaching, and depending on various process parameters, iron may be precipitated as hematite, goethite, jarosite or other oxyhydroxides, which may be more or less crystalline. Hematite is the favored precipitate because it is the most environmentally stable and does not ad/absorb as much copper, nickel or other solution constituents during precipitation. However, the low solubility of iron during the medium temperature processing of sulfide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. In some cases these phases have been positively identified as the metastable ferrihydrite, which transforms into iron oxides such as goethite, hematite and magnetite over time. A better understanding of what may help drive this transformation during leaching would ultimately result in lower valuable metal losses and more stable leach residues. Higher acid concentrations result in increased copper extractions and favor the formation of hematite during concentrate leaching, rather than other metastable phases. Furthermore, commercially available water displacement formula “WD40®” and other novel reagent(s) affect Fe precipitation and sulfur chemistry, leading to very different process outcomes such as improved extractions and larger, more easily separated, sulfur particles.

Jan 1, 2017

By Chen Feng

Compared to widespread successful deployment of robotic manipulators for repetitive and hazardous tasks in related industries such as manufacturing, the construction industry has achieved relatively limited benefits from robotics and soft automation. Unlike manufacturing, where robotic solutions benefit from the structured layout of the environment (e.g., factory assembly line), construction robots face unique challenges that arise from the rugged, dynamic, and unstructured environment of the work site, as well as the uncertainty and evolving sequence of occurring on-site events. This challenges any intended construction robots to not only replicate basic human motion, but also be capable of sensing and adapting to environmental changes, and making decisions based on the evolving state of the environment. Building upon recent advancements in robotic mapping, computer vision, and object recognition, the authors propose to introduce autonomous behavior at the basic task level for on-site construction robots to address these challenges in a flexible and extensible manner. This paper reports the outcome of the first phase of this research - a structured methodology for improved design and development of basic task automations - and focuses on algorithms developed for mobile robot navigation and relative pose estimation. The algorithms are implemented on a prototype mobile robotic platform, and evaluated in several experimental scenarios.

Aug 1, 2013

By Atulya Verma, Samantha Espley, Nashel Kalaka

Numerical modelling simulations of proposed mining sequences are used to evaluate mining induced stress concentrations and their migration associated with the progress of mining. This analysis is a standard practice for most prospective mining projects at various levels of feasibility study. The studies are usually initiated at the beginning of the mining cycle, on a global scale, and are maintained and updated throughout the life of mine (LoM) to identify or address local issues and the required remedies as and when needed. Developments in numerical modeling techniques along with advancements in computing technology and data storage/management capacity have given rock engineers access to a huge volume of data that needs to be analyzed and assessed. The most common approach to numerically evaluate stress concentrations and migrations in underground mines is to select the points of interest in a given volume such as the back of an excavation or points within pillars around critical infrastructure, and plot the stresses or a derivative of stresses over time to represent life of mine concentrations and migrations of stresses. The problem with this approach is the sharp gradient of stresses close to excavation boundaries. Slight changes in the location of selected points can change the stress concentration and migration patterns substantially and all generalized statements about LoM risk can be challenged in one way or another. For global stresses, the most common current approach of data analysis is by viewing series of pictures representing stress contours. In this approach, it is easy to overlook some critical detail and/or be masked by personal preferences of contour/picture representation. To overcome the problem of representing and analyzing huge volume of stress simulation data, the authors, through their experience at different mining operations, developed a volume-based technique to reliably evaluate mining-induced stress concentrations and migrations. The volume-based approach is for risk-based assessments of adjacent regions in the rockmass, in and around planned stoping excavations. The volume of interest is the entire ore body that is planned to be mined, but it could be just a part of the ore body depending on the specific use case. The risk identifiers are the induced stresses as compared to the strength of the rockmass. Over the LoM, the risk identifiers are tracked versus the corresponding excavation ratio of the zone. This approach is very effective in identifying the stages of mining that are contributing the most to the mining induced stress risk and the results can be used for proactive planning and mitigations measures such as alternative mining sequences, or stope sizes, or extraction methods. The approach has also been very successful in application at mature mines, particularly in assessing the re-initiation of mining in zone that has been dormant for some time. The volume-based approach allows for an assessment of the current state of the rockmass and the identification of future risks when planning resumption of mining activities.

Jan 1, 2023

By L. Tapia

The main disturbance for stability in primary grinding using SAG mills is related to continuous changes in the ore being fed to the plant, such as size and hardness. Searching for stability is the first step to accomplish, before trying to maximize the mill throughput. The time variability in the characteristics of the ore being fed from the mine to the plant must be known or inferred to perform adaptive changes in the grinding process control. In day to day operation, such information is not available in real time. Transport times and inventories between the mine and the plant complicate the situation. Under this scenario, Minera Los Pelambres implemented a grinding optimization strategy, based on the real time analysis of certain process variables, such as ore size, mill current consumption, pebble generation and throughput. As a result, both grindability and stability indexes are inferred. This is equivalent to inferring the ore characteristics by knowing its effect on the grinding behavior. These two indexes permit control of the SAG mill total charge level and hence, allow optimization of throughput by means of an expert control system.

Jan 1, 2007

Over the years, efficient on-line monitoring of performance and status of an electrolytic copper refining process has been challenging due to the need for complex electrical measurement systems and the management of the enormous volume of data. Recent innovative developments by Kennecott Utah Copper Corporation and Outokumpu Technology in wireless cell voltage and individual cell temperature sensing opens new possibilities to improve and modernize tank house management. This paper describes the powerful Outokumpu CellSenseTM refinery monitoring system for efficient interpretation of data produced by wireless CellSensorTM system with traditional refinery measurements. Examples from commercial tank house installations demonstrate the benefits of the system to improved process control and operation. The Outokumpu CellSenseTM monitoring system is simple to operate and accessible to all the plant operation teams.

Jan 1, 2007

By K. Thuro, B. Sellmeier, M. Krautblatter

"Recent rockfall events, like the Tramin rockfall at January 21st, 2014, underline the significance of a comprehensive hazard assessment. A common way of estimating the hazard along infrastructure is the performance of run-out modelling using 3D rockfall codes like Rockyfor3D or RAMMS::Rockfall (Dorren, 2010, Bartelt et al., 2013). The potential block volumes are often roughly estimated from talus material and an overview of the source area, where the magnitude assessment is usually physically and intellectually demanding. Nevertheless especially for increased magnitudes, the volume estimation is crucial in terms of hazard analysis. Mid-Magnitude-Events exceed the load capacity of the most mitigation measures and their date of failure is hard to predict. Here we define the term Mid-Magnitude-Events as block volumes between boulder falls (10-100 m³) and block falls (100-10,000 m³) (Whalley, 1984).The current contribution provides an approach of integral process analysis for a 200 m3 carbonate block above the federal road B 305 near the city of Salzburg in the Bavarian Alps, Germany. We performed detailed analysis of the critical carbonate block exposed to planar failure. The block volume and the dimensions of the failure surface were mapped in detail, due to the unique occasion of an accessible failure surface. The discontinuity persistence was recorded to assess a minimal degree of fragmentation for a potential failure scenario. A maximum degree of fragmentation was estimated due to recording of block dimensions at the talus slope resulting from frequent rockfalls.We performed parameter studies in terms of run-out modelling using the code RAMMS::Rockfall (Bartelt et al., 2013), taking the recorded data for block fragmentation into account. In our contribution, we aim to demonstrate a comprehensive approach for hazard assessment of mid magnitude rockfalls, taking detachment processes, fragmentation and run-out analysis into account."

Jan 1, 2015

By F. Filzwieser, K. Gamweger

The process of gas purging in molten aluminium has been an industrial practice in Europe for many years. The advantages are a reduction in the hydrogen content and impurities in the melt, as well as a homogenisation of the temperature and chemical analysis in the molten metal. Formerly used lances or impellers are being replaced by porous plugs which are installed at the bottom of the furnace. This special product of RHI Refractories has proven its efficiency in primary melting as well as in die cast, sheet and extrusion plants.

Jan 1, 2004

By K. Torigoe, S. Owad, C. Tokoro, Y Tsunazawa

The mechanism of an abrasion process to recover metal values by removing components from printed circuit boards (PCBs) is modeled using a discrete element method (DEM) simulation. To simulate the abrasion process, a model PCB geometry was constructed consisting of bonded particulates. The simulation allowed connections between particles to be broken if the bonding force calculated from DEM exceeded a threshold level. Simulation results were compared with experimental comminution data using an agitation mill with test PCBs on which nine capacitors were surface solder-mounted. Simulation results obtained from the DEM with the anchoring model corresponded to experimental observations.

Jan 1, 2011

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

"Several studies conducted recently have shown that molybdenite flotation from Cu-Mo ores is adversely impacted in sea water at pH >~ 10.0 irrespective of the pH modifier; under the same conditions Cu sulfide flotation is relatively unaffected. This has been attributed to the presence of Mg2+ ions and their hydrolysis products in the sea water which adsorb and precipitate on molybdenite surfaces as Mg(OH)2. However, why and how Mg(OH)2 impacts only molybdenite flotation in the complex flotation pulps containing a multitude of minerals is not understood. The work presented in this paper probes the interface and interphase regions near the edge and basal planes of natural molybdenite (MoS2) in aqueous solutions and flotation pulps, particularly in the presence of copper ore pulp and added Mg2+. Differences in interaction of metal ions and their hydrolysis products (Mg2+, Mg(OH)+) were measured on the two faces of this anisotropic mineral. How those differences relate to molybdenite floatability and the impact of aqueous solution chemistry are discussed.INTRODUCTIONWater resource management is an important sustainability challenge in mineral processing. In view of the shortage of fresh water in many parts of the world, mineral processing plants are evaluating alternative sources. Seawater flotation has received much attention recently and there have been several important studies reported in the literature, particularly for the processing of Cu-Mo ores (S. Castro, 2012; S. Castro, Rioseco & Laskowski, 2012; S. Castro et al., 2012; Laskowski & Castro, 2012; Ramos, Castro & Laskowski, 2013; S. Castro & Laskowski, 2013; Laskowski, Castro & Ramos, 2013; Nagaraj & Farinato, 2014; S. Castro, Uribe, & Laskowski, 2014; Veki, 2013). The main conclusions from these studies on Cu-Mo ores in seawater at elevated pH were: a) flotation recovery of Cu sulfides is either unaffected or only marginally reduced, b) molybdenite recovery is adversely affected in seawater at pH values necessary for rejecting pyrite (i.e. pH > 10 to 10.8 depending upon particular system), and c) the precipitation of Mg2+ in seawater as Mg(OH)2 is responsible for the adverse effect on Mo flotation. In order to further investigate the individual effects of Mg2+ and Ca2+ on molybdenite depression in Cu-Mo ore flotation, Nagaraj & Farinato (2014) conducted flotation tests wherein individual metal ions were spiked into tap water during grinding of Cu-Mo ores. They showed the strong adverse effect of Mg2+ addition on Mo recovery and, to a lesser extent, on Cu recovery when pH > 9.5. Under similar conditions, Ca2+ had virtually no effect on either Cu or Mo sulfide flotation. Figure 1 below shows the previous results for Cu- Mo ores in tap water and the effect of addition of Ca2+ and Mg2+ ions. Note that in seawater the adverse effect of Mg2+ on Cu recovery was much smaller than that in tap water (Nagaraj & Farinato, 2014; Figure 4a and 4b and Table 4 therein)."

Jan 1, 2016

By N. W. Xu, C. Sha, F. Dai, Y. G. Zhu, B. Li

Underground caverns stability and excavatability of rock masses are of significance in geotechnical engineering, in both design and construction stages. Risks associated with underground group caverns of Houziyan hydropower station in southwestern China are growing as a result of continuous excavation-induced unloading. To improve our understanding of the underground caverns instability and resolve the complex subsurface conditions of the highly fractured rock mass, a high resolution microseismic monitoring system was established in the deep underground caverns, pursuing the relationship between the measured data about microseismic activity and excavation damage zones of surrounding rock mass. Through analyzing the tempo-spatial distribution of microseismic activity, excavation damage zones and potential risk regions in underground caverns were identified. Furthermore, the correlation between microseismic activity and pre-existing geological structures, as well as traditional monitoring was analyzed. In order to validate the correlation between seismicity and potential slip surface of underground caverns, a model was implemented into numerical code to further evaluate the deformation and stability of surrounding rock mass. The monitoring results demonstrate that microseismic events mainly occur at high stress concentration regions, which coincides with the results obtained from numerical analysis. Therefore, the comprehensive method incorporating microseismic monitoring and numerical analysis, as well as traditional monitoring and filed observation has been proven to be very promising in deformation and even instability prediction of surrounding rock mass in underground caverns subject to delineation of potential slip surfaces and excavation damage zones.

Jan 1, 2015

By W. T. Gotheridge

The principal sources of coal-dust underground are, of course, coal, and the working of coal. Coal-dust is most dangerous when it is in the finest state of division. This class of dust is found mostly on the roads, being blown or shaken off the loaded trams in transit, or carried in suspension by air currents. The air current passing from the working faces may also carry dust in suspension into the return airway, and the air current from the surface may carry dust from the shakerscreens into the intake airways. The mosl dangerous dust we have to contend with is, (a) that which is most finely divided, and (b) that which contains the most volatile matter, including the inflammable occluded gases, and also oxygen absorbed from the air. According to experiments, coal-dust in a fine and dry state would intensify an explosion, in air free from fire-damp carrying in excess of 3 ozs. of fine dust or 6 ozs. of coarse dust per cubic yard. The volatile matter in the dust must be between 12 and 31 per cent. in the ash-free coal, the latter percentage giving the highest flame velocity. It is vary difficult to propagate flame where coal-dust contains a large percentage of stone-dust, (say 50 per cent.). Shale-dust or other incombustible dust containing no volatile hydro-carbons or carbonaceous matter will prevent the extension of an explosion if mixed with coal-dust in proportion of say 70 per cent., and if the dust is finely divided and dry.

Jan 1, 1924

By L. Gawlik

Since the beginning of the 20th century, coal has been the world?s main source of primary energy. In the last few decades, consumption of coal has gradually decreased in some European countries and elsewhere due to the introduction of other energy sources. Regardless, industry continues to use solid fuels for energy production despite of their association with carbon dioxide emissions (about 7 billion Mg). For global development going forward, it is important to estimate what level of energy consumption can be expected as far into the future as the next few decades. To answer this question, specialized global institutions such as the International Energy Agency, the World Energy Council, the World Coal Institute, the U.S. Energy Information Administration, the International Institute for Applied Systems Analysis, as well as oil companies (BP, Shell), conduct periodic forecasts of world energy consumption. The development of such forecasts is very complex because their reliability is influenced by many factors that are difficult to estimate, such as economic development, population growth, climate change, and public awareness. We are all aware that the global demand for electricity will rise significantly in the coming years as a result of anticipated population growth, industrial development, rising living standards, and the general development of civilization. The world?s mineable resources in 2010 were as follows: coal 665.6 million Mg, brown coal 195.4 billion Mg, oil 163 million Mg, and natural gas 185.5 billion m3. The annual global primary energy demand in 2008 was more than 12 billion toe (12,267 Mtoe). In 2006, electricity production in the world amounted to 18,921 TW?h. The structure of the primary energy mix in TW?h (2006) was as follows: coal 41.0%; natural gas 20.1%; nuclear fuel 14.8%; hydro energy 16.0%; liquid fuels 5.8%; and other renewable energy sources 2.3%. The European Union (EU) is one of the largest coal consumers in the world. In 2010, the EU-27 produced 396.1 million Mg of brown coal, and 132.9 million Mg of hard coal; 188 million Mg of coal was imported from outside the EU. The largest hard coal producers in the EU-27 are Poland, Great Britain, Germany, the Czech Republic, and Spain; major brown coal producers are Germany, Greece, Poland, the Czech Republic, and Hungary. For many years, the Polish energy sector has been based on domestic fuel sources ? hard coal and brown coal. The characteristic feature of the Polish balance of primary energy resources is a very high share of coal ? much higher than the world average. Pursuing the decarbonisation of the Polish economy may jeopardize Poland?s energy security, leading to a significant increase in electricity prices, which would hamper the country?s economic development. Price volatility and supply uncertainty are now the dominant features of the international markets for oil and natural gas. The high share of these fuels in meeting energy needs is the reason for unrest in many countries, including those in the EU. Under these circumstances, coal may become the stabilizing element of EU energy security.

Aug 1, 2013

By John Eggert, Paul Benford

"Since 1982, Placer Dome Inc. -Dome Mine has steadily increased mill throughput. Tonnage has increased from a nominal design capacity of 3000 short tons per day, attained in 1985, to 4130 stpd by the end of 1992. Many minor and major circuit adjustments were tried to maximize tonnage.Having utilized most conventional means of increasing tonnage, further increases required a newer approach. This paper discusses the Dome experience in the development and implementation of an expert system.The Comdale/C system was chosen for a controlled trial. The criteria for acceptance were: increased tonnage had to be sufficient to pay for the system; the increase had to be visibly sustainable and the mill operators had to be willing to accept the system.The criteria for purchase were met during the trial and the system was purchased. The system continues to perform well. The tonnage throughput increase has been sustained while operator acceptance remains high.IntroductionPlacer Dome Inc. -Dome Mine is Canada's oldest operating gold mine. The mine was among the first established in the Porcupine camp in what is now Timmins, Ontario. The City of Timmins is located approximately 500 miles or 800 kilometres north of Toronto. Figure 1 shows a map of the province of Ontario and the mine location.In 1912, milling began at a rate of 350 short tons per day. With two minor exceptions, milling has been continuous since this time. The first of these shut downs was in 1918 during the first world war. The war created labour shortages which forced the mine to stop production for more than a year. The second was in 1930 when fire destroyed the mill."

Jan 1, 1994

By Lee Nichols

The Oil Sand Industry in northern Alberta, Canada, disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called Consolidated Tailings or Composite Tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities. Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are long-term stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface. The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process.

May 1, 2004

By J. Peace, J. R. Fletcher

"British Steel has increased its usage of stainless steel for bunker, silo and chute linings to reduce maintenance costs and improve productivity.A generation of low cost 12% Cr steels has been specifically developed to satisfy the needs of hardness, flow promotion and through life costing which are demanded by bulk solids handling industries.The range of stainless steels include:• a very hard martensitic grade which is particularly suitable for high stress applications where impact and abrasion are predominant;• a titanium stabilized duplex steel for structural applications, as well as low friction , medium abrasion resistant wear liner plate; and• a ferritic stainless steel with rubber backing for low stress application where flow promotion of product is the predominant requirement.Industrial applications and experiences along with methods of fixin g the stainless steels will be discussed in conjunction with the relative through-life costs of the products.IntroductionBritish Steel has become one of the most efficient steel manufacturers in the world, with improvements seen in productivity, quality, delivery, performance and response to the needs of the worldwide market place.Part of this success stems from reductions in engineering downtime in the key areas of its operations, by the introduction of better engineering design and the use of enhanced materials where significant cost benefits have been identified.The nature of producing iron and steel requires the use and handling of a number of raw materials with wide ranging properties, each calling for a different approach to solving the difficulties encountered in storing and transporting these materials to their respective point of use. Figure 1 shows steel production for 1988-89 where over 30 million tonnes of raw materials were handled in making 14 million tonnes of liquid steel at British Steel&apos;s five integrated works.Typically solid raw materials include, iron ore, coal, limestone, ferro alloys and scrap. Intermediate products such as coke and sinter create their own specific handling and wear problems.Coals and ores are shipped into the United Kingdom from several sources, and have a great variety of properties. Some coals can be extremely wet and sticky, whereas others are dry and dusty . The ores handled can vary from wet concentrate and fines to heavy angular rubble and pellets. These raw materials are off-loaded, stored and conveyed through British Steel&apos;s own port facilities at Port Talbot, Immingham, Redcar and Hunterston. British Steel also produces the majority of its own coke and all its own sinter. Coke and sinter are frequently handled at elevated temperatures which cause other handling problems."

Jan 1, 1991

By Jan Rosenkranz, Anders Sand, Lisa Malm, Nils-Johan Bolin

Within flotation technology the general trend is towards very large cells. Scale-up is usually done by postulating geometrical similarity, which implies keeping the aspect ratio constant when increasing cell volume. Consequently, the design of flotation circuits typically involves several cells of identical geometry within a bank. Using a few standard sizes in a flotation plant simplifies design, manufacturing and maintenance of the cells, but does not necessarily guarantee optimal performance and selectivity of the flotation process. Geometry parameters for a given cell volume that influence flotation cell performance include cell height, which causes changes in the hydrostatic pressure and suspension hydrodynamics, and also influences the travel distance of particle-bubble agglomerates as well as the homogeneity of the mixing. Also the thickness of the froth layer depends on the aspect ratio of the cell. The objective of this work is to gain a better understanding of material distribution and properties within a flotation cell and, based on this information, elucidate how alterations of the cell geometry can influence separation efficiency. For this purpose systematic measurements and analyses of the spatial distribution of the different phases within a 160 m3 flotation cell have been carried out with a particular focus on an industrial, low-grade copper ore beneficiation process. The concepts for sampling at different vertical and lateral positions of the flotation cell are introduced. The results from the experimental work give an understanding of internal material distribution within flotation cells. Based on the measured phase distribution and concentrations as well as particle properties at various positions within the cell, the implications for an optimized scaling and design of individual flotation cells within a flotation circuit are discussed.

Jan 1, 2016