Search Documents

By I. Mc Dougall, H. Joubert, G. de Villiers

The use of sidewall copper cooling systems to prolong furnace campaign life is becoming an accepted technology solution in the base metals industry. Tenova Pyromet has designed and installed a number of sidewall copper cooling systems in base metals furnaces, including the platinum industry. Apart from increasing the furnace campaign life through the formation of a stable freeze lining, a well-designed copper cooling system enables the plant operator to focus more on optimizing the process to achieve throughput and recovery targets, and to accommodate more varied and available concentrate feed blends. The paper discusses the design of sidewall copper cooling systems for copper smelting and converting furnaces to achieve the above objectives. More specifically, the design of copper cooling systems for top submerged lance furnaces are discussed. An overall increase in furnace heat losses has been raised as a concern for intensively cooled sidewalls. The paper explores the overall heat loss expectations for copper cooled furnaces versus traditional refractory lined furnaces. In addition, the potential use of alternative cooling media is discussed. INTRODUCTION Base metal smelting and converting furnace technologies have been evolving continuously over the past century to satisfy the need for higher throughput, improved efficiency, and longer campaign life. To accommodate these demands, in particular higher smelting intensity and throughput, furnace bath containment systems had to improve. The use of pure refractory lining systems has slowly made room for the use of more intensively cooled lining systems (Joubert, Nikolic, Bakker & Mc Dougall, 2016). These cooling systems evolved from external shell cooling, such as shower or film cooling, to copper plate coolers extending into the furnace refractory lining, and high intensity stave or panel coolers (Verscheure, Kyllo, Filzwieser, Blanpain & Wollants, 2006). Consequently, an increasing number of base metal smelting and converting furnaces are equipped with copper cooling systems, including flash furnaces (Bryk, Ryselin, Honkasalo, & Malmstrom, 1958; Yasuda, Motomura & Kawasaki, 2014; Marx, Shapiro & Henning, 2010), top submerged lance primary smelting and fuming furnaces (Bhappu, Larson & Tunis, 1994; Kim, Lee & Lee, 2000; MacRae & Steinborn, 2018), top submerged lance converting furnaces (Viviers & Hines, 2005; Nikolic, Hogg & Voigt, 2018), primary platinum smelting electric furnaces (Nelson, Stober, Ndlovu, De Villiers & Wanblad, 2005; Jones, 2005; Hundermark, De Villiers & Ndlovu, 2006; Mc Dougall, 2013), and electric slag cleaning furnaces (Joubert, Nourse, Masters & Hundermark, 2005).

Jan 1, 2019

By SangHyeok Han

Selecting the best possible cranes and identifying spatial conflict-free locations on sites can result in productivity and safety improvements for large-scale industrial construction projects. In the current practice, experienced lift engineers select cranes based on the heaviest lift and/or the largest lifting radius of the identified crane. This practice is relatively time-consuming, and optimization of the crane?s use and location is also difficult. There are many factors which need to be considered during the crane selection process, a reality which further complicates the process. This paper presents a framework which aims at developing a decision support system to enhance the crane selection process and collision-free path planning for large-scale construction projects. This paper utilizes an innovative crane selection matrix in order to establish a process for optimized crane selection for construction projects. The study considers more than 40 different factors in order to reduce time and improve safety for crane operations. Following finalization of crane type (mobile crane versus tower crane), a visualization model to simulate crane operation and identify collision-free crane operation paths is proposed. This process can assist project managers to plan the lifting process more effectively and efficiently. A case study-based approach was utilized to demonstrate the proposed methodology. The methodology was tested in the planning and construction process for boiler house structures in Mannheim, Germany. The project entailed numerous challenges: one of the major tasks was to lift a 102-ton load on the top of the boiler structure through crane collaboration; space limitations on site also presented several challenges related to crane selection, location, and operation processes. Based on the project constraints, the proposed crane selection framework, and the visualization models, two tower cranes were selected and successfully implemented in the case study.

Aug 1, 2013

By Marcotte P.

Introduction Pneumatic jackleg rock drills are commonly used in underground mining operations. These tools are known to expose their operators to hand-arm vibration levels in the order of 20-35 m/s2 weighted (Wh). Thus, the majority of the workers who have cumulated several years of jackleg rock drill operation are affected by related health problems such as Raynaud's syndrome or carpal tunnel syndrome. Up to now, no efficient personal safety device was available to protect pneumatic rock drill operators against hand-arm vibration (HAV). To address this problem, an anti-vibration handle prototype for jackleg drills has been developed in a previous study. Then, a multi-partner project was launched to refine the prototype and commercialize an effective anti-vibration handle for pneumatic rock drills.

Feb 1, 2008

By D. B. Langford, R. Hart

"This paper presents an overview of the state-of-the-art in industrial and utility power metering and control systems with particular emphasis on Digital Power Meters and Power Demand Controllers.IntroductionModern micro-processor technology, combined with very fast, high accuracy analog to digital converters, is rapidly allowing economical, digital power instrumentation systems to replace the traditional electro-mechanical meters and equipment previously used for instrumentation, control and protection in industrial power systems. Consequently, instrumentation and Supervisory, Control and Data Acquisition (SCADA) systems that were only practical for the very large utility or user are now available to smaller utilities and users. The information available includes sequence of event recording, trend logging, energy management cost allocation and automated load control, among others. The heart of any power monitoring system is the Digital Instrumentation Package (DIP) . These ""DIP's"" include Digital Power Meters (DPM's) and Power Demand Controllers (PDC's) as well as other specialized instrumentation packages such as Mini RTU's."

Jan 1, 1991

By Deni Côte, Michel Dagbert, Marcel Vallée

"Greater reliability of mineral deposit and reserve estimates can be attained through better quality control of the data and information acquisition, and the estimation processes. This paper reviews the following key requirements:1. greater awareness of the significant figures of both data and estimates, and better understanding of the probabilistic aspects of the estimates, their confidence limits and margins of error;2. greater reliability of the information that supports the estimates, by more explicit and more rigorous methods and standards for data acquisition and for interpretations;3. more quantitative estimations of geological/mineral continuity, based on improved three dimensional sampling patterns and the use of geostatistics; and 4. better integration at the project engineering and mine production stages, of the mineral deposit characteristics and mining method constraints, for more efficient mineral recovery and mine quality control.RÉSUMÉUne plus grande fiabilité des estimations des gisements et des réserves minières requiert plus d'emphase sur le contrôle de la qualité de I ‘acquisition de l'information et du processus d'estimation. Les exigences suivantes sont revues:1. le respect du niveau d'exactitude des données et des estimes en n'utilisant que le nombre approprie de chiffres significatifs des observations et mesures, et en exprimant le niveau de confiance et la marge d'erreur des estimations;2. l'amélioration de fa fiabilité des données par des normes plus rigoureuses pour leur acquisition et leur vérification, et par des méthodes plus systématiques d'interprétation et de modélisation;3. l'estimation plus rigoureuse de la continuité des minéralisations dans les trois dimensions des gisements, par des patrons échantillonnages mieux adaptes awe paramètres géologiquement minéralogiques, et par l'utilisation des méthodes géostatistiques; et4. l'intégration plus poussée, particulièrement lors de la planification de l'exploitation minière, des caractéristiques des gisements avec les contraintes des méthodes d'exploitation, pour améliorer la récupération et le contrôle de la qualité en exploitation."

Jan 1, 1993

?Introduction to the Delphi Group ?Why is carbon important to your organization ?Key elements of a carbon management strategy ?Inventory ?Risk & opportunity scan ?Mitigation options and financial mechanisms ?Identify targets and develop policy ?Communication and improvement ?Manage for success

May 1, 2009

By M. J. Dry, G. B. Harris

"This paper presents basic chemistry and operating conditions for the hydrolysis of ferric chloride into solid hematite and gaseous hydrogen chloride, and shows how this unit operation can be applied in chloride hydrometallurgy to regenerate strong hydrochloric acid and reject iron without also rejecting valuable metals such as nickel, copper and cobalt. Two examples are used to illustrate the hydrolysis technology and compare it to existing technology. The first is the regeneration of spent steel pickling acid, comparing hydrolysis to conventional pyrohydrolysis. The second example is the processing of a hypothetical low grade nickel laterite, comparing the novel chloride hydrolysis route to conventional sulphate HPAL technology.INTRODUCTION Whilst, in many respects, the control and removal of dissolved iron from chloride leach solutions can resemble the manner in which it is done in sulphate systems, chloride chemistry additionally offers the ability to achieve the same objectives in different ways (Harris, 2014). Conventionally, iron is oxidised to its ferric state (if necessary) and then precipitated with a base, usually magnesia where the feed is a laterite and lime where it is a sulphide, since calcium will precipitate sulphate formed during leaching. One method for controlling iron is to form FeOOH, either ß-FeOOH (akaganéite), a-FeOOH (goethite), or a mixture thereof (Fillipou and Choi, 2002). However, if akaganéite is formed, the precipitate will contain a significant chloride component (as high as 7% Cl), leading to chloride losses and difficulty in satisfactorily disposing of the residue. Washing chloride from akaganéite is almost impossible due to the propensity of the solids to undergo peptization. The conventional approach requires the addition of a base, but it is based to some extent on controlled supersaturation precipitation (Demopoulos, 2009), which produces a more uniform and crystalline material and is far more attractive than, for example, the turboaeration process proposed by Great Central Mines in their chloride copper process (Raudsepp & Beattie, 1986)."

Jan 1, 2016

By Walter Koellner

Today?s large electric mining shovels are significant users of power and represent peak loads of more than 3.5 MW to a mine?s distribution system. The power swings during normal operation can influence the line voltage at the Point of Common Coupling (PCC). The static converters for the shovel?s motions also create voltage and current harmonics which are fed back into the mine?s power grid. In addition, shovels themselves are affected by the power quality of the mine?s distribution system. This paper introduces the use of active IGBT rectifiers, also called Active Front Ends (AFE), as alternative to conventional, line commutated SCR thyristor rectifiers. The AFEs convert the AC line input into a controlled DC-link voltage. This DC voltage is then used as input to IGBT inverters, which power the AC motors of the shovel?s Hoist, Propel, Crowd, and Swing motions. The introduction of AFEs creates the following operational improvements: i) reduction of the Harmonic Current Distortion THDi from more than 40% to less than 4%; ii) full regenerative operation; iii) the potential for line voltage stabilization at the PCC; iv) high tolerance for line voltage fluctuations; v) improved dynamic performance, and, as result vi) higher availability and productivity of the shovel.

May 1, 2001

By T. Yameogo

Many ideas, tools, technologies, and methodologies are believed to have staked their claims on the future of mining. For example, automation is strongly positioned as the platform within which mining will be practiced. A subset of automation ? intelligent mining ? will add some smart interactions between machines, technologies, the rock, and the environment. The future also calls for an improved approach to sustainability and corporate social responsibility. Mines of the future are dreamed of to be more ethical and more balanced. They will boast optimized designs, integrated value and supply chains, produce less waste, recycle and reuse, and will require less energy to operate. Then, what about the people that will operate this optimized ecosystem? How is the education system teaching the operators of the mines of the future? What kind of a future should mining education foresee to prepare the workers appropriately? In recent years, the shortage of skilled labor for mines around the world has created a tough competition to attract, retain, and train the very people without whom mining will cease to exist. In Australia, Canada, and the United States in particular, the war for talent has resulted in higher-than-usual labour costs. Such costs have dented the unit costs of many mining businesses. Concomitantly, mining contractors? and consultants? prices have increased to reflect the escalation of labour costs across the value chain. From labourers to engineers, from juniors to seasoned professionals, the increase in compensation is unprecedented. Yet, the shortage is still hurting the industry, and the high calibre candidates continue to be rare gems. The industry has been implementing aggressive solutions that include the increased hiring of skilled immigrants, the training and recruitment of minorities, and the retaining of near-retirement experienced employees. Public relation campaigns about the benefits of embracing careers in mining are also common. The CIM has also devoted a ?M4S? section to its pan-Canada meetings to educate the public, especially the youth, about the importance of the mining industry for Canada. Moreover, mining associations and universities are enticing students? enrolment through scholarships and financial support. Still, the balance between quantity and quality of workers can be discussed. This paper intends to discuss the present state of mining education as an essential part of the future of mining. The authors brush the picture of the education of miners, technicians, and engineers, against the backdrop of the technology-advanced mines of the future.

Aug 1, 2013

By J. Ji, A. Shi, B. Grcic

Floating copper minerals selectively against iron minerals such as pyrite has been challenging for most copper and copper/gold deposits, and many operations continuously strive to maximise copper recovery whilst meeting target concentrate grades. Maximising grade is achieved by selectively floating copper minerals and rejecting pyrite. This challenge is to minimise copper and gold losses in the roughers if this approach is used. A flotation testing program was conducted by Bureau Veritas Minerals on a high-level pyrite bearing copper/gold ore sample to establish the potential to reject pyrite in the rougher stage, but also maximise copper and gold recoveries, and ultimately final product grades. The test program included feed characterization, rougher and open-circuit cleaner flotation as well as locked cycle flotation tests. The main variables tested for achieving selective flotation of copper and gold were collector type and pH control, through lime addition. Grind sizes used in the rougher and cleaner tests had been established from previous test work. The collectors tested were SIPX, Aerophine® 3418A, Aerophine® 3421, Aerophine® 3422, Reagent S-11192 Promoter, Reagent S-11193 Promoter and FloMin C4150. The two best performing collectors were then tested in open-circuit cleaner tests, with the optimum conditions examined further in locked cycle tests. INTRODUCTION Bureau Veritas Minerals Metallurgical Division was retained by Eldorado Gold Corporation to perform a metallurgical testing program on a high-level pyrite bearing copper/gold ore sample from a gold- copper porphyry deposit to optimize flotation reagent scheme to improve gold and copper recoveries and copper content in the concentrate. The test program included feed characterization, rougher and open-circuit cleaner flotation as well as locked cycle flotation tests. Initially, various collectors were screened in kinetic rougher tests, and over a pH range of 8.5 (i.e the natural ore pH) up to 11.5, using a primary grind size of 80% passing 120 µm. The collectors tested were SIPX (sodium isopropyl xanthate), Aerophine® 3418A, Aerophine® 3421, Aerophine® 3422, Reagent S-11192 Promoter, Reagent S-11193 Promoter and FloMin C4150. The enrichment ratio, which is the ratio of copper to sulfur in the concentrate to that in the feed, was used as proxy for rating selectivity (i.e. degree of pyrite rejection or depression).

Jan 1, 2019

By E. M. De Souza, P. Lausch, D. O. DeGagné, J. F. Archibald

"The potential use of industrial and municipal waste glass as a partial pozzolanic replacement for Normal Portland cement in mine backfill has been investigated. Considerable quantities of glass are currently discarded into landfill sites at high cost to municipal and industrial users with no foreseeable environmental benefits being gained by such disposal. This research study was undertaken to assess the viability of using ground waste glass materials as partial binder replacement of Portland cement fractionswithin consolidated mine backfill materials. The program was implemented to review various factors that could influence successful incorporation of glass waste replacement of cement, these factors being the feasibility of glass waste procurement, determination of process economics and the physical and chemical suitability of ground waste glass materials to generate adequate backfill strength when replacing Normal Portland cement fractions. A series of laboratory assessment trials were established to evaluate backfill component characteristics and mixture strength properties for both standard Portland cement-consolidated and blended Portland cement/ground waste glass-consolidated backfill materials. Side-by-side review of the strength behaviour of various component backfill/cement mixtures was designed to permit comparative evaluation of the capabilities of ground waste glass and Portland cement products as backfill consolidating agents"

Jan 1, 1995

By J. Duriez, L. Scholtès, F. V. Donzé

"Fracture propagation process in brittle rock is investigated by means of numerical simulations performed with an adapted formulation of the discrete element method. The progressive failure mechanism is simulated through the breaking of the bonds making up the cohesion between the elements constituting the simulated medium. The use of appropriate contact laws associated to a near neighbor interaction feature provide the model the ability to reproduce fundamental characteristics of brittle rock behavior such as, for example, high values of the tensile to compressive strength ratio. Great attention is given to accurately describe the properties of the pre-existing joints or faults in the model. A specific joint model gives the possibility to define a tailor-made behavior of the discontinuity surfaces without suffering from discretization bias.Compression test simulations are performed on pre-flawed samples and compared to experimental results in order to validate the numerical approach for describing the initiation and propagation of fractures in brittle rock under mode I+II loading. It is shown that the crack mechanical parameters can greatly influence the fracturing pattern, in particular its frictional properties. Overall, the numerical simulations reproduce fairly well the failure patterns that are obtained experimentally.The discrete model is then used to study mode I+III loading to give an insight into fracturing problems occurring at the scale of the continental crust. The ability of the model to support mechanically the physical modelings performed with wet clay or sandbox is shown. As an example, the model is used to track the development of a twist crack system (wrench fault) through the nucleation and coalescence of microcracks."

Jan 1, 2015

By David Christensen

The long-term performance of dry covers is being examined in a research study funded by the International Network for Acid Prevention (INAP). The study was separated into two phases. The two main components of Phase 1 of the study were the identification and research of the processes affecting the long-term performance of dry cover systems and an examination of available numerical models for simulation of long-term cover performance. Identification and research of the physical, chemical, and biological processes affecting long-term performance showed that cover performance could be related to the change in the saturated hydraulic conductivity of cover material, the change in the soil-water characteristic curve, and the physical integrity of the cover system. Seven numerical models were examined to evaluate their effectiveness in predicting the long-term performance of cover systems. VADOSE/W (Online Help v1.01, 2002) was selected for use in cover system modeling in Phase 2 of the project. Phase 2 of the research study is currently in progress and involved the selection of five mine sites with a minimum of three years of performance monitoring data for analysis of cover performance. Two of the mine sites will be analyzed with the two-dimensional VADOSE/W numerical model. In addition, field saturated hydraulic conductivity tests were completed at three mine sites to investigate the change in field hydraulic conductivity of the cover system materials. The objective of the field testing program was to evaluate changes in hydraulic conductivity of cover material with time. Measurements of field hydraulic conductivity were completed with a Guelph permeameter and a pressure infiltrometer at three sites. The field hydraulic conductivity data was used to evaluate whether a change in this key material property had occurred over time. Field observations and the historic performance monitoring data provided the necessary information to develop hypotheses as to the likely processes that led to any change in field hydraulic conductivity. This paper will briefly summarize the research completed in Phase 1. The remainder of the paper will focus on the field testing program completed to measure the field hydraulic conductivity of constructed cover systems.

Nov 1, 2002

By Wei Ye, Lei Li, Xianjian Guo, Feng He

The purpose of the paper is to study the smelting process of copper concentrate with high Cu/S ratio produced in Africa or other areas around the world and theoretically analyze the influence of slag type on the smelting process. The paper has compared the processes used successfully in smelters, including CAPEX and OPEX and other factors, to provide reference for the industry to select the best process under specific conditions. INTRODUCTION At present, a great amount of copper concentrates with high Cu/S ratio, with chalcocite being the major source of copper, have been produced or are about to be produced in the Copperbelt in Africa and other countries in the world. The copper concentrate is usually high in copper (~30–55wt.%) and low in sulfur (~10–15wt.%). The conventional processes of smelting-converting and roasting-leaching-electro-winning for treating this type of concentrate is high energy and materials consumption such as electric power\fuels\flux et al. The direct-to-blister (one-step) smelting process can be considered favorable due to a reduction in processing steps. Up to now, there are four copper smelters in the world operating with the direct-to-blister smelting process. There certainly are problems in the process such as high copper content in the slag, strict operation requirement of slag cleaning electric furnace, etc. Except technical issues, the impact of factors on economical aspect such as power and material cost needs to be considered comprehensively in process selection. In this paper the technical issues of direct-to-blister smelting process, including slag treatment process, were analyzed and the comparison to the conventional processes and economic analysis of direct- to-blister smelting process to treat high Cu/S ratio concentrate were done.

Jan 1, 2019

By Douglas G. Jay

"Transfer points on belt conveyors have long been a source of problems for both designers and users. Conveyors are generally given a low priority in new equipment layout, thus designers are often forced to compromise due to space limitations. Consequently, for this reason as well as for reasons of initial economics, many conveyors are supplied with less than adequate transfer points.Although not intended as a cure-all, a number of existing installations have been modified with the result that spillage has been reduced to a minimum and belt life has been extended. The most striking modification consisted of replacing conventional rigid frame idlers with five-roll catenary idlers.Although catenary idlers can be traced back to the early 1900s in North America, with a patent having been issued in Washington, D.C. as early as May 29, 1907, the practical application of this concept has only recently reached North America. Major installations include applications at St. Lawrence Cement in Oakville and Iron Ore Company of Canada in Sept-Iles, as well as belt conveyors at Stelco's Nanticoke plant and yard conveyors at Syncrude in Alberta. These installations were part of major capital expenditures for new facilities and included complete conveyor systems.However, this article will discuss the use of catenary idlers on existing rigid frame conveyors for the purpose of absorbing the energy of falling lumps, protecting conveyor belts and reducing spillage. We will deal specifically with an installation at Inco Metals Company in Sudbury, Ontario, where approximately 40 five-roll catenary idlers were installed on a 42-in.-wide belt conveyor handling ore located under the railroad car dumper at the Clarabelle Mill. Before-and-after photographs clearly show the tremendous improvement in the cleanliness of the location, and the savings in maintenance costs and extended belt life have prompted Inco to consider modifying other conveyors."

Jan 1, 1982

By J. G. Bensley, K. S. Detheridge

"Many plants use computers for process control and most have computerized Management Information Systems but few have been able to have these systems interact with one another. Developing this system interaction is not a one-step process but requires careful planning and implementation. This paper describes two projects that were implemented to provide the bridge between the process control and management information systems of Cominco Limited. Both projects include the replacement of essentially process control systems installed in the late 1960s. These original systems provided an enhanced level of control in the form of Direct Digital Control (via computer/manual analogue control stations) and a management reporting capability of process data. The experience gained from the use of these systems over a period of fifteen years formed a basis for the evaluation and planning for the new systems. The new systems were commissioned in 1985 and 1986 and operating and further developments leading to a totally integrated process information and control system are underway. INTRODUCTIONThe concept of hierarchical control involves a control structure consisting of a number of defined levels. Each level performs a defined function with information consolidated and combined as it moves up through the hierarchical structure. The commonly accepted structure of a hierarchical control system echoes the structure of the plant which is being controlled. Referring to Figure 1:Level 0 - Sensors and ActuatorsSensors and actuators, such as thermocouples and flow control valves, interface directly to the process and are generally connected directly to the controllers or multiplexers at Level I.Level 1 - Regulatory ControlThis level provides basic PID control (proportional/integral/ derivative) typically using microprocessor based controllers and programmable controllers for digital control of motors and machines. Systems at this levelare usually segregated by plant unit, e.g, crushing, flotation, drying. Control is concentrated on achieving optimum conditions for a particular feed rate."

Jan 1, 1989

By Y. Kocaefe, D. Bhattacharyay, D. Kocaefe

The carbon anodes used in the electrolytic production of aluminum are made of petroleum coke, recycled anodes and butts, and coal tar pitch. Due to technological advances in the aluminum production technology, aimed at increasing production and decreasing energy consumption and greenhouse gas emissions, better quality anodes are required. Presently, the anode quality is evaluated by visual inspection and the analysis of a small core taken from 1.5-2% of the anodes produced. The visual inspection is susceptible to human error and limited to surface imperfections. The analysis of cores takes time, and therefore, it is difficult to determine the existence of a problem and intervene at the right time. In addition, the core does not represent the whole anode due to the non-homogeneity of anodes. A validated online anode quality control system can highly improve the situation. In this article, an electrical resistivity measurement method developed for this purpose is presented.

Jan 1, 2014

By Gautier Njiekak

The current study provides an experimental approach that aims at documenting the effects of different phases of CO2 (gas, liquid, supercritical fluid) on rock seismic responses. This has implications on obtaining quantitative estimates of fluid saturations for geological storage. The ultrasonic pulse transmission technique is the underlying methodology used in this work. Unlike previous rock physics studies involving CO2 as pore fluid, care is taken to fully saturate the studied samples and also to separate pore fluid effects from pore pressure build-up effects during the experiments. This allows to record seismic effects that are solely reflective of changes in the pore fluid properties. Measurements were done on a CO2 saturated Berea sandstone. Laboratory results show P- and S- waveform variations (velocity, amplitude) in response to CO2's varying phase state. Overall, CO2 phase changes (gas to liquid and gas to supercritical fluid) are marked by a drop in velocities, with the drop being smaller and less immediate over the gas-supercritical fluid transition than over the gas-liquid transition.

Jun 1, 2012

By D Martín, G. Díaz, F. Cubeddu, A. B. Mejias

The Modified ZINCEXTM Process (MZP), developed by Técnicas Reunidas, is an industrially proven flexible process. It can handle a wide range of primary and secondary raw materials, producing SHG zinc. The core of the Modified ZINCEXTM Process is the zinc solvent extraction unit. This unit is an effective barrier for any leachable impurities present in the raw material. As a result of this an ultra-pure zinc solution is always obtained. The high versatility of the process makes the application of the technology in different scenarios possible. MZP can be effectively applied when developing a whole new plant (Skorpion) or adapting its scheme to an existing refinery (Akita), in both cases giving the same results. Flexibility in terms of capacity of the plant is a great advantage of the MZP, there is the possibility to adapt the global process to a wide range of production capacities. Zinc production capacities of over 150 000 t/a may be achieved with a single solvent extraction plant train. The robustness of the Modified ZINCEXTM Process has been recently proven on two new plants currently in operation: Portovesme (Italy) and Horsehead (USA) after start up during 2013. The status of both plants is described in this paper.

Jan 1, 2014

By Denni Nikols, Farrukh Z. Khan

"Highvale Mine, located at Wabamun, Alberta, produces thermal coal for TransAIta's Keephills and Sundance generating plants. Overburden stripping in the mine is conducted by draglines which normally operate on top of the overburden bench. In certain areas oj the mine, however, these overburden benches are susceptible to slope failure. In these areas, due to safety considerations, the draglines are utilized in the less productive chop-cutting mode, supplemented by mobile equipment where the bench height exceeds the dragline chop-cutting limit. This paper proposes maintaining the draglines in their normal digging mode through areas of unstable or jailed overburden, by utilizing a dragline carried toe buttress 10 ensure adequate bench stability. The data requirements and methods of slope analysis to design a toe buttress across an unstable highwall area are examined in rigorous detail. INTRODUCTIONLocationHighvale Mine is owned by TransAlta Utilities Corporation and operated under contract. It is Canada's largest coal mine with an annual coal production in excess of II million tonnes. The mine is located approximately 80 km west of Edmonton on the south shore of Wabamum Lake (Fig. I) and production is currently provided by three pits 02. 03 and 04 (Fig. 2). The entire coal production is consumed at the nearby Sundance and Keephills power generating plants.ScopeThe mining operation at Highvale Mine has had occasional slope stability failures of its high wall overburden bench. This paper examines one such failure which occurred in the summer of 1983 at Pit 03. In addition to an investigation of the failure, Terracon was asked to recommend mine operation procedures which would minimize the impact of these slide zones on dragline productivity. A method of removing the failed material by utilizing the dragline in its normal digging mode is designed. The method's advantages and disadvantages as well as the required support procedures are reviewed."

Jan 1, 1989