Search Documents

By O. B. Horne, R. O. Morgan, C. E. Anderson

"Air-photo interpretation and photogrammetry are two of the most effective and versatile tools available to the petroleum industry. The techniques have proven successful in providing solutions to many of the problems encountered in the design and construction of oilfield projects.Although most technical personnel are aware that air-photo interpretation and photogrammetry are useful in the selection of routes for roads and pipelines, few realize the true scope of the techniques or the wide variety of areas in which they are applicable.This paper briefly describes the principles involved, and reviews a number of typical applications of particular interest to petroleum companies. Excessive detail is avoided, rather the emphasis is placed upon the wide spectrum of possible applications. It is stressed that on-the-ground examination generally is a necessary adjunct, and that there are certain limitations to the techniques discussed.Properly applied, however, air-photo interpretation and photogrammetry can offer significant advantages in terms of time, flexibility, secrecy and economy."

Jan 1, 1968

By D. Royston

In SAG mills fed with a variety of ore types, hard packing between the shell lifters can come and go depending on rock type and rock size distribution and the presence of a binder. Packing can appear in all sizes of SAG mills, and can be tenacious. High ball impact forces (depending on ball size) in larger mills may compact and encourage packing. Packing can have a negative impact on milling performance and a change in shell liner design may be required to remove it. However shell liner design changes need to be managed with care to ensure liner reliability. In smaller mills control of packing can extend shell plate wear-life and may help to maintain milling performance in fixed-speed mills through the liner wear-cycle.

Jan 1, 2012

By Y. Champoux, N. Atalla, R. Oddo, C. Lesage

"Percussion drills are the source of the most serious noise problems in mining activities, due to their extremely high noise levels(114-122 dB(A)) and widespread use(Bartholomae and Stein, 1988). Percussion drills will continue to be widely used to drill small diameter holes in hard rock because no other method seems to be economically avail-able to replace them (Boillat et al., 1993).Many studies (Danière, 1991; Hawkes etal., 1977a; Jensen and Visnapuu, 1972;Leblond et al., 1976; Milette, 1989) were con-ducted to determine the major noise sources of percussion drills. The exhaust air of pneumatic drills, the hammer, the bit in contact with the rock and the drill rod have been identified as the major noise sources. A muffer can be used to reduce the exhaust noise and the hammer can be enclosed. The bit noise is considered to be of concern only at the beginning of holes. When all the available methods are used to reduce the noise of a percussion drill, the drill rod vibrations become the dominant noise source (Hawkes and Burks, 1979). However, the noise levels generated by this source remain high and future efforts should concentrate on reducing its radiation.Works by Hawkes and Burks (1979) and Hawkes et al. (1977b) for the U.S. Bureau of Mines provide the most complete description on the noise and vibration of percussion drill rods.The longitudinal and bending waves are the two most important types of elastic waves generated in drill rods. Among these, only the longitudinal waves contribute to the drilling rate. The bending waves are caused by non-centralized impacts, drill rod curvature and non-uniform bit/rock interface. Drill rod noise is generated by Poisson’s ratio expansions and contractions of the rod as the longitudinal waves travel up and down it and by transverse rod motions induced by bending waves. The radiation efficiency is much higher for bending waves than for longitudinal waves. Most of the impact energy is transformed into longitudinal waves, as expected for axial impacts. The evaluation of the relative contribution of longitudinal and bending waves to noise generation poses a very difficult problem for experimental, analytical and numerical approaches. It is, however, an important issue because the relative contribution of these two waves will guide future noise reduction efforts. It seems that very little can be done to reduce the noise radiation of the axial waves without affecting the drilling rate. The main difficulty that analytical and numerical approach-es face, in the evaluation of the relative contribution of the two waves, is that there is no adequate theory for predicting the bending vibrations from the factors that cause them. The experimental approach has, thus, been limited to test fixtures that do not adequately represent the boundary conditions, as well as by measurements obtained under real operating conditions from which it is difficult to establish the relative contribution of the two types of waves. For example, Hawkes and Burks (1979) and Hawkes et al. (1977b) used a test fixture with free-free boundary conditions and made no clear link with measurement under real operating conditions. Rather, they have based their discussion on a simple model. Many authors assume that fexural waves are the main noise source on drill rods. However, measurements have been somewhat contradictory and researchers are still unable to state with certainty that this is indeed the case (Lednik et al., 1988)."

Jan 1, 1997

By M. Somppi, D. Weirmeir, Z. Yamak

"Milling operations commonly employ activated carbon to capture complexed gold from lixiviants in leaching processes. As the carbon moves through pipes, pumps, vessels, kilns and other processes in the gold leaching circuit, this consumable may experience losses by various mechanisms like attrition, breakage, and rupturing. Whenever possible, capturing the fine gold-bearing carbon portion of this stream could provide value to milling operations at low capital cost and manageable financial risk. Identifying, testing, and validating the successful payback of a low-tech flocculant system is described. However, the work more closely explores a Monte Carlo risk-based methodology for understanding the potential payback of this project at various confidence levels – an approach that many improvement projects can follow where some level of uncertainty exists.INTRODUCTION Gold milling operations commonly employ activated carbon to adsorb gold from solutions. Normal handling causes the carbon particles from this material to abrade, break, rupture to a size that becomes too small for further use in the process. Operations often concentrate on capturing the fine particles because gold is associated with the carbon and this metal content can be a valuable revenue stream for toll processing. However, the small particle sizes become difficult to separate from the process and can ultimately leave the facility in the waste stream. Hence, operations often place a great deal of care in capturing as much fine carbon as possible by a variety of methods including using screens, settling tanks, and chemical methods. Retrofitting a circuit to capture more carbon fines is common but can expose the operation to financial risk. Approaching this potential improvement by leveraging a Monte Carlo methodology can be effective in understanding the risk and the associated payback of a project at various confidence levels. This method provides a strong framework for capital go-no-go decisions and the structure to validate the potential project success before implementation."

Jan 1, 2019

By K. E. Waters, E. R. L. Espiritu, G. R. da Silva

"Rare earth (RE) elements are essential components of emerging green technologies. The increase in demand for these applications have driven the search and development of new rare earth deposits such as the Niobec project in Quebec, Canada. This deposit consists primarily of dolomite with significant amount of RE minerals bastnäsite and monazite, the primary sources of RE elements. Due to the minerals’ fine liberation sizes, flotation is commonly used as a concentration method. To develop an efficient process, the electrokinetic properties of the minerals must be understood. In this study, the surface properties of bastnäsite, monazite (RE minerals) and dolomite (a common gangue mineral) were investigated by zeta potential measurements. These measurements are affected by various ions present in solution; for bastnäsite, monazite and dolomite, some of these ions are H+, OH-, PO43- and CO32-. Dolomite, being a sparingly soluble mineral and a primary component of the ore, may be the greatest contributor of these ions in solution in the form of CO32- ions. Thus, different sources of CO32- ions (from dolomite dissolution and from Na2CO3) were investigated. The research work aims at elucidating how these reagents may influence the minerals’ surfaces. The results have shown that dolomite supernatant and sodium carbonate greatly affect the electrokinetic properties of each minerals. The addition of dolomite supernatant have resulted to relatively similar zeta potential of the minerals; while, sodium carbonate have affected them differently. These observations could be useful in efficient flotation of bastnäsite and/or monazite from bastnäsite-monazite-dolomite system.INTRODUCTIONThe increase in the demand for rare earth (RE) elements has driven the search and development of new deposits. Out of 53 rare earth projects in the world, 19 can be found in Canada (Hatch, 2015). These include the Niobec project of Magris Resources Company in Quebec. This deposit contains a significant amount of rare earth minerals (such as bastnäsite and monazite), with carbonates (such as dolomite) as the primary gangue minerals."

Jan 1, 2016

By W. H. MacLean

The Matagami district lies directly west of Chibougamau on the north side of the Abi tibi greens tone belt. Ores at Matagami are volcanogenic massive sulphides and occur in the dominantly rhyolitic Watson Lake group surrounding the Bell River Igneous Complex. Rhyolites and basalts of this group, and basalts of the overlying Wabassee group in the central part of the district, are tholeiitic; calc-alkaline Wabassee rocks occur in the western part. Massive sulphides occur associated with rhyolite domes that can be delineated by paleotopographic and isopach mapping. They are mainly distal deposits that formed over an extended period of time while several volcanic units were being deposited,

Jan 1, 1984

By Tim J. Carew, Dennis C. Martin

"One approach to stabilization of rock slopes is to place a buttress at the toe of the slope to provide additional resisting forces and increase the length and strength properties along the failure surface. This paper describes the rock mechanics and mine planning aspects of incorporating a buttress of intact rock in the lower part of the slope as part of the slope design for the south wall of the final pit at Cassiar Mine. Stability analysis techniques and results are described. Analyses results have indicated that, in order to maintain steep over-all slopes in the final pit, a buttress of intact rock shoud be incorporated into the lower section of the slope until late in mine life. The effect of the buttress is to flatten the slope and reduce the slope height thereby improving slope stability. The mining plans would be such that the buttress would be mined out during the last four months of mining when the consequences of instability would be least severe.IntroductionThe concept of using a buttress to stabilize slopes has been used in mining and civil engineering construction in may locations (Richards and Stimpson, 1977). Most buttresses involve placement of coarse rock fill timber cribs or other material as a load at the toe of an already unstable slope to provide forces which resist failure by counteracting driving forces and increasing the length and strength of the failure path.This paper describes the geotechnical and mine planning aspects of incorporating a buttress of intact rock in the design of the south wall of Cassiar Mine. The effect of an intact rock buttress is to flatten the slope and reduce the slope height, thereby improving slope stability. No actual construction is required other than normal excavation of the slope. The ""mine plans would be such that the buttress would be mined out at the end of mine life when the impact of instability would be less severe and additional ore might possibly be recovered from the slopes. Mining of the buttress could induce instability at the very end of mine life at a time when maximum ore extraction has been achieved."

Jan 1, 1986

By T. Richard Davies

This paper primarily deals with the application of wearfacing materials and their role within a well-established preventive maintenance welding program. Some examples are shown, as well as a synopsis of possible benefits and a compendium of methods and materials.

Jan 1, 1979

By N. R. Thornton

This paper discusses the rapid growth in the application of instrumentation for metallurgical process control. It covers such methods as ultrasonics, pulp density measurements, on-stream X-ray analysis and reagent control, as well as the expanding use of computer control and data acquisition.

Jan 1, 1971

By C. W. MacLeod

LOCATION The Goudreau gold area in Ontario extends from a point a short distance south of the main line of the Canadian Pacific railway, at Lochalsh, in a south-westerly direction to the Magpie river. It crosses the Algoma Central & Hudson's Bay railway at Goudreau station, 177 miles north of Sault Ste. Marie. The area is roughly 25 miles in length by 6 miles in width. The potential gold formation is much more extensive but little prospecting has been done outside of the limits mentioned. The actual continuous area of Keewatin formation, in which gold has been found, is one of the largest in Ontario. ACCESSIBILITY Probably no mining area in a similar stage of development has had the excellent transportation facilities which Goudreau enjoys. This field is traversed in part by the main lines of the Canadian Pacific and Algoma Central railways. The Provincial Government has constructed 22 miles of road through the heart of the camp. Sixteen miles of this road is suitable for motor car traffic and several cars and trucks are in constant service.

Jan 1, 1926

By E. H. Rose

THE most useful guide to the role of lime in flotation is the view that the chemistry of any flotation operation is primarily a pattern in relative solubilities. We have the coming together of a number of minerals, reagents, fortuitous salts, water, and oxygen, many of which have not been previously in contact with each other, and every one of which is free, at least to some extent, to abandon old alliances and to form new ones. Of one thing the operator may be sure, and that is that, when equilibrium has been reached, those new chemical combinations will have formed which are the least soluble combinations possible to the environment. The laws of solution govern the operation, which means that relative concentrations are always a factor, and temperature frequently is. What the operator is really doing when he chooses his reagents .in the first place (empirically or otherwise) and works out their? optimum amounts, is to provide an environment in which (1) the least soluble possible compound of the mineral he desires to float is one which is also non-wettable, while at the same time (2) the least soluble compounds possible to the minerals he desires to depress are wettable. Since all metathesis is reversible, perfection is impossible to achieve, and the operator is constantly striving to establish that combination of concentrations which will drive each and every particular reaction as far as possible in the direction he desires it to go, in accordance with the law of molar concentration.

Jan 1, 1939

By A. P. LeBis

This article attempts to relate the concept of utility to the risk involved when only a small number of projects (compared to their probability of occurrence) are accessible to a firm and to quantify utility when other financial and physical parameters are known.

Jan 1, 1978

By K. Ihara, R. Akiyoshi, Y. Takaki, S. Kang, H. Shishido

"Tensile tests and scanning electron microscopy-electron backscattered diffraction (SEM-EBSD) analysis were performed in an Al-Mg-Si alloy to clarify the effect of annealing and cold-rolling reduction on the texture formation. The hot-rolled specimens were cold-rolled with the reduction of 58-75%(CR1), followed by annealing at 773 K for 5 min(IA). The secondary cold-rolling(CR2)for the IA specimens with the reduction of 33–66%, followed by the solution heat treatment(ST), were performed. Focusing on the CR1 and CR2 specimens, the average r-values increased with higher primary and lower secondary cold-rolling reduction, respectively. This was considered to be due to the increase of r-values measured in the direction of 45 degree with respect to rolling direction, caused by the formation of the ß-fiber components (Brass {011}<211>, Copper {112}<111> and S {123}<634>) with high density. Based on the texture analysis of annealed specimens it was suggested that the high density of the ß-fiber components after IA and the small amount of stored strain energy of CR2 introduced by the lower cold-rolling reduction remained the ?-fiber components even after solution treatment.INTRODUCTION Al-Mg-Si alloys have been applied to automobile body applications, due to their excellent paint-bake hardening (age-hardening) and corrosion resistance compared to other aluminum alloy. On the other hand, the mechanical properties and deep drawability of Al-Mg-Si alloys are inferior to those of steels. Thus, it is important to improve the mechanical properties and deep drawability in order to expand the application components. One of the best methods to improve the deep drawability is to increase the Lankford coefficient (r-value). Previous studies reported that the increase of the average r-value ( ) improves the deep drawability. The relationship between the r-value and texture of the alloy is also well known. Inoue et al. reported that the ß-fiber components, such as Brass ({011}<211>), Copper ({112}<111>) and S ({123}<634>), increase the r-value measured in the direction of 45o with respect to the rolling direction. r"

Jan 1, 2018

By C. O. Swanson

Introduction It is thirty-odd years since I first entered the mining field by working underground at Anyox, which makes 1t clear that I can qualify as one of the older generation and claim the privilege of dealing in generalities and broad impressions. In this position I find it interesting to re~ view the salient changes that have taken place during the past quarter-century and indulge in some speculations concerning the future, with the hope that my comments may be of value to others engaged in the field of mining geology. As indicated by the title, the treatment is a perspective from a single viewpoint rather than an attempt to give a complete and impartial analysis. This plan, while deficient in some respects, has the advantage of being more specific than one based on .a. compilation of opinions. An additional advantage is brevity, which would be difficult to obtain on a subject of this scope if it were viewed from all angles. In conformity with the general plan, specific references to the literature have been avoided as much as possible, although a number of publications of general nature are listed at the end of the paper. This procedure is intended to give credit to the sources used without making them in any way responsible for the interpretation. The starting point for the discussion is the situation as it existed twenty-five years ago, when, as a recent graduate, I first had a fairly complete picture of it. However there is one impression of an earlier; stage that seems worth mentioning. In one of my first courses in geology the statement was made that some of the leading authorities of the previous generation, who guided geological thought at about the beginning of the century, were inclined to question the value of an association with mining. This attitude was no doubt exceptional, and certainly it was not adopted by the students who laid the groundwork for mining geology in North America. But its existence even in a limited circle is significant m showing how far the application of geology has advanced as the result of the investigations started during the first part of this century.

Jan 1, 1949

By A. Bhowmik

Uranium Refining is the process in which undesirable neutron absorbing elements such as Boron (B), Gadolinium (Gd), Cadmium (Cd), Europium (Eu), Samarium (Sm) and other heavy metals (Fe, Ni, Co, Ca, Mg etc.) are removed to make it nuclear pure. At present, Uranium refining is carried out by solvent extraction process by using organic based solvent e, g. TBP diluted with Kerosene. The above process generates lot of nitrate bearing liquid waste and degraded organic. In order to eliminate use of hazardous organic and ammonia for Uranium refining altogether, a new process has been developed. In the new process, Yellow Cake is dissolved in nitric acid and uranium peroxide hydrate is precipitated selectively from the solution leaving all the impurities in the solution by using commercial grade hydrogen peroxide at a pre-defined pH, U conc., temperature and stoichiometric quantity of hydrogen peroxide under mild agitation. The precipitate is filtered and washed with DM water to obtain nuclear pure product meeting purity standard as per ASTM C ? 753-99.The product is spray dried and calcined to obtain uranium oxide. The process eliminates use of organic, flammable, toxic chemicals, consumes less quantity of nitric acid and uses environfriendly chemical hydrogen peroxide. The process is simple and can be integrated in the mill. A patent application is entering national phase in several countries including CANADA and abstract/full paper is available in WIPO publication no: WO/2009/013759.

Aug 1, 2010

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, P. Ghobadi

Design and selection of equipment for a grinding circuit strongly depends on the mill function, ore properties and requirements of the down-stream circuit. Primary mills usually work in open circuit and size distribution of product would be controlled in the final steps using a classifier like cyclone. Although HPGRs are mostly utilized as pre-grinding mills, it is preferred to utilize them in a closed circuit due to their specific mechanism of comminution. Unique mechanical design of HPGR and its completely different crushing process than tumbling mills needs precise consideration on its circuit design. In this paper, we investigate the impact of different parameters on design of pre-grinding HPGR circuit and selection of the proper classifier. Our study focuses on iron ore properties (e.g. moisture, particle size distribution of feed and product, compatibility and de-agglomerability). We also investigated various options of HPGR circuit according the classifier efficiency and influences on down-stream processes. The optimum operating parameters of HPGR (working pressure, speed and level of hopper) for the selected circuit were also determined based on pilot and industrial data. Our pilot and industrial tests and observations revealed that HPGR should be arranged in closed circuit because of the edge effect, as a negative factor of non-uniform distribution of pressure force along the roller width and presence of non-crushed particles in the mill product. Wet vibratory screen could be the optimum option for screening of its discharge. Fine part of the wet screen discharge could be delivered to the concentration stage without over-grinding in ball mill using a hydrocyclone working in a reverse closed circuit mode. Moreover, our pilot and industrial tests during design and operation of ten HPGRs in various iron ore processing plants proved that higher pressure and lower roller speed in a fixed level of material inside the hopper could give the desired product size distribution.

Jan 1, 2016

By Lucas G. Thompson

My topic, "The Administration of Mineral Rights&apos;.&apos; is possibly an unusual one, as it deals with a subject upon which many of us have a more than passing interest, I thought ?it might prove consistent with the objects of this meeting, more especially as I propose to deal, not with those broad subjects of nation-wide importance which are often the subject&apos;? of learned (and sometimes futile) academic discussion, but rather with problems in their practical light. To the scientist, the important question is What is it? to the technician, Can it be utilized? to the business-man, Will it pay? All three questions are important, and so quick has been the march of business on the heels of science? that the one question follows the other with astonishing rapidity and all three must be considered in the modern management of a mineral estate. A .good illustration of the force of this can be found in the recent advance of our knowledge of the element helium in which we have advanced from a solution of the first question to the last question in the short period of 55 years. It is to be borne in mind, however, that in the administration of mineral rights, the question "Will it pay?:&apos; is of primary importance. What forms a mineral estate ? A former practice in western Canada in selling lands was to sell the hair with the hide. All transactions sold the lands in fee simple, which included all mines, minerals and rights and privileges whatsoever, excluding only the royal metals, gold and silver, which by imputation, though not by specific reference, in deeds. of title are reserved to the Crown. At that time the country was in the first ?stages of settlement and the value of our mineral resources was hardly appreciated and little understood.

Jan 1, 1923

By D. Campbell

Mining activity is increasing in northern boreal and subarctic regions of Canada. This is the case in the far north of Ontario, especially in and near the Hudson Bay Lowland (HBL). De Beers Canada opened the Victor diamond mine in the centre of the HBL in 2008, and advanced exploration and impact assessments are occurring to the west in the ?Ring of Fire? for ferrochrome, nickel/copper, iron/ vanadium and platinum-group elements, making it one of the richest mineral finds in Canada in recent years. However, the HBL is also a near-pristine, sensitive environment. Its peatlands forms the third largest wetland in the world and are globally important stores of terrestrial carbon. Human populations in the region are sparse, consisting almost entirely of First Nations communities. Local First Nations also have a strong land ethic and greatly influence mining developments. Through formal agreements, they have insisted on a gold standard for environmental management, including a small mine footprint and the return to representative native ecosystems after mine closure. However, knowledge on the revegetation of subarctic and northern boreal ecosystems is limited. Here, we are conducting research at the Victor mine to develop gold standard protocols for the revegetation of disturbed peatlands and mine waste uplands and present a summary of results. We first tested existing protocols for peatland restoration from southeastern Canada. We collected peat-forming plants from nearby muskeg, spread them sparsely over disturbed peatlands and applied a light phosphate fertilizer, but unlike southern protocols, no mulch appeared to be required to produce a representative cover of peat-forming plants within three years. A bigger challenge is the reclamation of uplands made of mine waste back to representative ecosystems. We first characterized reference conditions for uplands in the HBL, which are scarce in the region. Nearby natural uplands were divided into two classes, interior uplands and uplands along river valleys. Multiple parameters were examined at these sites including soil development, bulk density, soil chemistry in the rooting horizons, plant cover by stratum, plant species composition and dead wood. The mean condition and, more importantly, the range of these parameters allow us to set broad targets for progressive reclamation, which will facilitate success. Finally, we characterized local upland plant species through their functional traits to determine their likely abilities to colonize, grow and contribute to ecosystem processes. A classification of species by these simple functional attributes will help restoration managers to select candidate species to meet different goals at different successional stages (i.e. good versus poor dispersers or establishers). Research into these protocols remain in the early stages, but show promise that gold standards can be achieved to ensure that mining wastes can be reclaimed to productive ecosystems.

Aug 1, 2013

By C. W. Eggert

This paper gives an account of the E.V.O.P. tests made at the Copper Rand mill of the Patino Mining Corporation in Chibougamau, Quebec. The runs were made to acquire an understanding of the method. A description of events, along with conclusions, observations and opinions, is out-lined.

Jan 1, 1967

By Daniel Torres Espinoza, Jose Pinedo

"Ventilation is a vital service in underground mines, required to provide fresh air to the work force and dilute diesel equipment gases (CO, NOx) and diesel particulate matters (DPM). At a Mexican precious metal mine in the state of Chihuahua there is a VOD system implemented using Howden’s control and monitoring system and a state of the art tagging and tracking technology. The JM zone of the mine is ventilated using a push and pull system, using automated regulators on each level to control the air going in and out of the levels. The implementation of advanced control strategies using Howden’s VentSim™CONTROL allows the mine to generate significant savings and increase health and safety of the workers.INTRODUCTIONIn underground mines, ventilation is a requirement in order to maintain the fresh air needed for personnel and equipment. Ventilation regulations dictate the amount of air required underground to carry out day to day operations by limiting the exposure that workers have to toxic gases and other pollutants. Regulations for required airflow in underground operations for diesel pollutants are generally provided on vehicle rated brake horsepower, in Mexico the requirement is 75 cfm/bhp. In underground mines, ventilation services can account to up to 75% of the mine’s energy consumption, and it is very common for fans to operate all the time because of a lack of control infrastructure for the ventilation system. By the implementation of a Ventilation On Demand (VOD) system a mine can reduce this consumption with different control strategies. The main infrastructure required to implement this system consists of remote control of ventilation infrastructure (fans and regulators), a communication network between throughout the mine with the surface and a tracking system for personnel and diesel equipment. Software is required to determine fresh air requirements based on the tracking system data and then send the control commands to the different ventilation infrastructure. In 2015, San Julian Mine acquired Howden’s VentSim™CONTROL (formally SmartEXEC) and the hardware solution to deploy a VOD system at their operation. The VOD system and Fresnillo plc’s San Julian Mine in Chihuahua, Mexico, consists of control of 10 surface exhaust fans, 2 surface intake fans, and 12 underground automated regulators. It also includes the monitoring of 46 flow sensors, 28 CO sensors, 28 NO?? sensors and 42 temperature and humidity sensors, approximately 500 personnel tags, approximately 220 vehicle tracking tags with diesel status (ON or OFF) and approximately 250 tracking zones. This paper discusses the control strategies that have been implemented at San Julian Mine since the system was commissioned and the next steps that will be taken at the mine with the system as they test different level on VOD."

Jan 1, 2019