Search Documents

By M. Kim, M. Ha

"The effect of red mud on the melting behavior of ferronickel slag was investigated by a laboratory-scale horizontal tube furnace. Melting and softening of slag samples fluxed with different amount of red mud was examined by in-situ visualization technique at temperature range from 1400 to 1550°C. FactSageTM 7.0 was used for the thermodynamic calculation of multi component system of ferronickel slag and red mud. Liquid phase area was extended to lower temperature by adding red mud indicating its suitability as a flux material. X-ray diffraction analysis confirmed the dependency of the phase changes on the red mud content. Microscopic observation by scanning electron microscope (SEM / EDX) clarified the phase transformations from olivine to spinel along with red mud additions.INTRODUCTION Ferronickel smelting by submerged arc furnace (SAF) is an energy intensive process performed at high temperature range 1500–1600°C. During the smelting process of saprolitic nickel laterite ore with a nickel content of 2.2–2.3 pct, a large quantity of ferronickel slag is being produced that account for 97 pct of ore charged. To achieve ferronickel grade of 15–20 pct Ni, electrical energy of 80 to 85 MW is used for the melting and reduction of nickel oxide (NiO) and iron oxide (FeO) in the ore (Rodd et al., 2010). Unreduced components, mostly MgO, SiO2 and partly FeO are removed from the furnace in a liquid slag form by a tapping operation. Due to the high melting temperature, forsterite (Mg2SiO4) based slag containing approximately 10 pct FeO requires typical process temperature of 1600°C. Flux in metallurgical process is a medium that decreases melting and operating temperatures while it increases fluidity of the liquid slags. Calcite and fluorite are examples of flux materials used for the ironmaking, steel refining and continuous casting process. Oxide systems based on CaO - CaF2 - SiO2 - Al2O3 - MgO cover most of the slag composition in ferrous metallurgy accordingly. Crucial operating factors for ironmaking and steelmaking slags are basicity (typically CaO/SiO2 ratio), viscosity and impurity levels. These are extensively controlled by the fluxes. General metallurgical fluxes such as limestone, dolomite and calcium fluoride are abundant in nature and supplied to steel mills at low prices. Meanwhile, in copper flash smelting process, silica is supplied with copper concentrate to remove iron oxide (FeO) generated from sulfide oxidation. FeO - SiO2 binary system formulates eutectic area at 25–38 pct of silica that has low melting temperature below 1205°C. Fayalitic system (Fe2SiO4) that has low viscosity (0.1 Pa·s) (Park et al., 2011) facilitates easy separation of slags from molten sulfide mattes. Recently, copper plants actively utilize recycled raw materials as a flux. Various recycled glasses are ground and fed to copper smelting process as a partial replacement of silica ore. Applying industrial wastes to smelting processes is advantageous since the operators can reduce the production cost remarkably. Not to mention the consumption of recycled materials can ultimately minimize the environmental risks and the waste management costs. The authors, therefore, investigated the reasonable waste materials that can be effectively used for ferronickel smelting process. Prerequisites for potential fluxing materials are non-recyclable property, low transportation cost and excellent performance as a flux."

Jan 1, 2017

By A. M. Esteves

This paper offers an overview of local content policies and practice in the mining sector. Specifically, the paper aims to answer the question of how national and regional governments, industry and civil society can work together to seek an optimal outcome while pursuing their diverse objectives. The paper begins by defining local content and its scope at the subnational level. Specific recommendations for the design of local content policies to mitigate social, economic and governance risks are developed. The document then offers some recommendations regarding the role of partners in design, implementation, monitoring, and enforcement of local content policies.

Aug 1, 2013

By S. Goodman

Successful exploration for and exploitation of a mineral deposit requires an accurate understanding of the deposit architecture in 3D, and of the development of the mineralizing system through time, which requires a thorough comprehension of the structural framework of the deposit. The integration of geological, geophysical and geochemical datasets to arrive at a 4D structural framework is well-established and has been successfully applied by SRK Consulting in projects from deposit to regional scale. In some cases, we can go beyond this, applying the SEEBASETM technique, which utilizes a ?bottom-up? approach to basin analysis. SRK?s approach primarily relies on the interpretation of magnetic and gravity data, calibrated with many other datasets including mapped geology, topography, event histories, wells/drillholes and seismic data. The SEEBASETM model is a culmination of this data integration and is produced through an iterative process of structural interpretation and geophysical modeling, where an interpretation of basement composition and 4D structure is used to constrain depth-to-basement geophysical modeling, and the modeled depths are then used in conjunction with the structural interpretation to constrain contouring of the basement topography. The result is a rigorously calibrated, 3D view of the basement surface, which can be used to understand the basement and basin architecture, and thus serves as a predictive exploration model. This technique, which was developed for use in the petroleum industry, is now finding success as a predictive tool in mineral exploration.

May 1, 2003

By D. W. R. George, J. L. Stewart

Developments in the last decade, which have contributed to increased productivity and decreased coke rates in the iron blast furnace, are reviewed. Future progress in blast-furnace practice is also considered.

Jan 1, 1966

By Saikat Chatterjee, Xintong (Brett) Liu, Kinnor Chattopadhyay

Magnesia carbon bricks are commonly used in BOFs and are generally pre-heated before the BOF goes into service. Owing to very stringent emission regulations, the BOF pre-heating process need to be controlled and optimized so that, the emission standards are met. One of the major concerns in organic emissions are its stringent limits on emission rates and total volatile emissions. In the present work, an attempt has been made to integrate CFD and Thermodynamic models to predict the emission rate of volatile organics during the pre-heating process. A one dimensional heat transfer model was developed using visual basic and then integrated with thermodynamics calculations using FactSage 6.4. The parameters that affected organic emissions were the pre heating procedure, gas composition of the burner, heating rate and type of the burner. Typical composition of MgO-C bricks and binder materials were obtained from literature and vendor data sheets. Chemical reactions between organic materials, refractory and burner gasses were considered. The model predictions indicated that certain burner conditions could destroy all organics before it exits the vessel while other conditions needed the use of an after burner at the mouth of the vessel. The model was also able to predict the organic emission rates based on the chosen pre-heating profile. This kind of predictive model will be very useful for the steel industry and enable them to justify permit limit applications and stick to the limits by fine tuning their pre-heating process.

Jan 1, 2015

By John Loui Porathur

Highwall Mining has been recently introduced in India. The first Continuous Highwall Mining extraction in India started operating at Ramagundem Opencast Project-II (OC-II) of Singareni Collieries Company Ltd. (SCCL) in December 2010. A new hybrid empirical and numerical modelling approach has been devised to design web pillars for the initial Highwall Mining sites in India, considering the complex geology, such as existence of thick seams and multiple seams in close proximity. This paper gives the scientific elucidation of a comprehensive design methodology adopted for the above mentioned Indian Highwall Mining sites. The design technology includes web pillar design for multiple seams using hybrid empirical and numerical methods, slope stability assessment, ground movement monitoring, and recommendations for conducting blasting operations in the vicinity of Highwall Mining extractions.

Aug 1, 2013

By Raymond B. Hryciuk

Environmental auditing has evolved rapidly over the last decade — first in North America, then Europe, and most recently in Asia — into a widely practiced discipline designed to provide senior management with assurance that operations are being managed in compliance with established governmental standards, internal company policies, and good industry practices. This paper first examines the evolution of environmental auditing, focusing in particular on three interlocking driving forces: company initiatives, collaborative industry initiatives, and government initiatives. Characteristics of effective audit programs, those that have emerged among the leaders, are discussed, including: objectives, scope, coverage, approach, staffing, and organizational considerations. The author then addresses important future trends and developments for environmental audit program design, content, and coverage.

Jan 1, 1996

By A. H. Lang

"The great interest taken in uranium in Canada during the past few years has resulted in the discovery of a very large number of occurrences, and in much research that has added to the knowledge of the mineralogy and geology of uranium deposits. The object of this paper is to present that information in condensed form. Some of it has been published before, but the writer has been asked to bring it together and to add more recent, unpublished data. The paper therefore contains short accounts of the mineralogy of uranium and of the types and distribution of occurrences; brief regional descriptions, including information on some of the characteristic deposits; and conclusions regarding prospecting and development possibilities.The writer has access to much confidential information supplied in compliance with regulations of the Atomic Energy Control Board. He has used this only for making broad generalizations that could not affect individual interests, and only where the owners of properties have agreed to its use.Much of the information on mineralogy and geology is derived from the work of others. The writer is particularly indebted to M. H. Haycock and S. Kaiman of the Mines Branch; H. V. Ellsworth, S. C. Robinson, E. J. Brooker, H. R. Steacy, W. E. Hale, and A. M. Christie of the Geological Survey; and E.W. Nuffield, J. S. Stevenson, and other officers of provincial Departments of Mines. For information and many courtesies he is greatly indebted to so many officers of Eldorado. Mining and Refining (1944), Limited, and owners and staffs of private properties, that it is impossible to mention them individually."

Jan 1, 1950

By R. Bruce Graham

The formation, evolution and classification of peat bogs is discussed. Factors resulting in the internal and external morphological changes in a bog are described. The fibrous, absorptive and sterile properties of peat moss account for its widespread use in horticulture and related fields. These properties also account for its usefulness as a binder in pelletizing, as an insulating material in bat tons and in panel construction. Peat, the humijied product of peat moss is used in market gardening and sod growing. It is utilized in Europe as fuel. It is a source of activated carbon and gas. Potentially peat can be used to produce waxes, resins, tannins, cellulose, hemicellu/ ose, humic acids, lignin and hymatomelanic acid. At present other cheaper sources are available.

Jan 1, 1984

By E. Esmaeilzadeh

There arc 8 primary ball mills in the concentrator plant and their task is material crushing. At the time of balls charge to mills, a lot of noise is produced. This noise would affect all grinding areas. The aim of this research was a reduction about 16 dB at source sound power level (SWL was 129.1 dB). With considering two noise control principles, noise producer sources and propagation paths were specified. For removing and reducing of noise producer sources, rubbers with a thickness of 5-20 mm were used on the all inside surfaces of charge box, ball transferring box and exit canal. For increasing transmission loss and damping coefficient of charge box body, rubber with thickness of 1 cm at outside surface of box was used. For reduction of noise propagation a secondary metal cover was designed and made. This cover includes two parts and was set around the charge box. Glass wool (75 kg/m3) with 10 cm thickness was used as acoustical absorbent between free space of two body's layers and from secondary cover side. The of the rest space was left empty. After installing of secondary cover on the ball charge box no.4, SWL showed a reduction about 16 dB. For studying of control system effect on noise reduction at points far from of charge place, measuring results at these points showed the maximum reduction 12.1 dB and the minimum 11.8 dB.

Jan 1, 2007

By E. L. Martheleur

Introduction In October, 1945, the Coal Division of the Institute appointed a Committee on The Use of Electricity in Coal Mines, with the following terms of reference: ?To study under which conditions in each deposit the use of electricity can be brought closer to the coal face and which types of electrical machinery can be recommended?. It was not until the beginning of this year (1946) that the Committee had a chance to convene and .discuss the conclusions which are embodied in this report. Mr. McLeod, as Chief Electrician of the Dominion Coal Company, is intimately concerned with that Company's installations, and Mr. McIsaac, as Electrical Inspector of Coal Mines for Nova Scotia, is well acquainted with installations in all coal mines in the Province. The knowledge of both has been very valuable in helping to draft this report.

Jan 1, 1946

By G Zahary

THE most acceptable approacl1 to analyzing rock behaviour, at the present time, is based on the application of principles of mechanics and strength of materials. Analyses have been made in which the criterion of failure is based on maximum stress (1) and on Mohr's rupture theory (2). If such analyses are to be carried out, the mechanical properties of the rock must be known within acceptable limits. Although an adequate correlation of laboratory test results with field conditions has not been established, test results have been published (3) on the basis of their comparative value. That is, test results may be useful for comparing the behaviour of different rocks under similar loading conditions or of a particular rock under different loading conditions. This study aims at establishing some of the mechanical properties of an andesite rock by testing specimens cut _from diamond drill core. Drill core (EX) was provided from run-of-mine drilling by New Dickenson Mines Ltd. and Campbell Red Lake Mines Ltd.

Jan 1, 1963

By S. Beitler

The availability of renewable energy does not meet the demands of consumption. Hence, fossil fuels will continue to be an important energy source, and coal promises to cover the requirements for the coming decades. Because of its high energy content, deep lying bituminous coal and anthracite are important for energy generation. One trend in the future of coal mining is thin seam mining, because thick seams more and more have been exploited. A well-known and approved longwall mining method for thin seams is plowing which has big advantages compared to a shearer because of its compact design. The extraction of those thinner coal seams will become more and more important in coal industry and therefore the plow will receive more attention in future. Most approaches in longwall automation are focused on the shearer and need a more or less intelligent exploitation machine. Therefore those approaches cannot be used for the plow technology. The authors introduce a shield-data-based horizon control (SDHC). The developed approach integrates the shield data provided by the roof support and process monitoring into the horizon control process to keep the plow in seam even if the seam trend changes. This control concept can be used for the shearer as well as for the plow. The basic idea of SDHC for plow application will be introduced in this paper and first simulation results will be shown.

Aug 1, 2013

ABSTRACT The inevitable uncertainty in modelling spatial variables decreases as more data become available. This reduction depends on the properties of the variable being modelled. Spatially continuous variables show less uncertainty for a given spacing than erratic variables. A geostatistical simulation based approach is developed to quantify the relationship between uncertainty and data spacing. Reference realizations are sampled to condition additional realizations and quantify uncertainty. The procedure is automated, making it straightforward to consider sensitivity and different geological domains. A case study of the relationship between uncertainty and data spacing for net oil sands thickness data from northern Alberta is presented. _ KEYWORDS Simulation, Sampling,

Jan 1, 2013

By W. J. D. Stone

"For several years, the existence of a deposit of barite (BaS04) near Brookfield, Nova Scotia, has been known. A very large deposit of strontium (SrS04) near Sydney, Cape Breton, is a more recent discovery. Cape Chemical Syndicate has been formed to work the deposits. A five-million-dollar integrated mineral processing and chemical plant is planned for Sydney to produce various compounds of barium and strontium. The mineral processing plant includes the Jones Wet Magnetic Separator and will produce high-purity barite and celestite. These products will be processed further in the fine grinding plant and the chemical plant. The general project is described, covering the deposits, processing and markets."

Jan 1, 1969

By M. Timmins

Campbell Mine operates a 100 tpd gold autoclave that treats sulphide concentrates at 305 psi and 200 °C. Autoclave feed consists of fresh pretreated concentrate, an acidic oxide slurry recycle as well as other high arsenic sources. The brickwork that is used to construct the five compartments of the vessel must be inspected and repaired periodically. Shutdowns are scheduled to inspect this brickwork and at times replace entire sections of the brick walls or lining. It also provides an opportunity to repair or replace other internal features such as agitator blades or oxygen spargers. Mechanics and contractors are scheduled around the clock to perform the maintenance requirements. There are many safety considerations and precautions that must be taken in order to protect the well-being of the workers and minimize damage to sensitive pieces of equipment. Heat, arsenic and lead contamination and confined space issues are just a few of the hazards involved. The following paper will describe how these safety concerns are addressed and will serve as a guide for future autoclave shutdowns.

Jan 1, 2004

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 130 machine-years of operation at locations in North America and Europe. ST has also installed separators for the beneficiation of industrial minerals in North America and Europe. The technology has been successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, barite, and potash.

Aug 1, 2013

By J. C. Heaslip

Introduction The greatest single advance in rock drilling practice since the advent of percussion drills was the introduction of tungsten carbide tipped rock drill?bits. The evolution of rock drills has been a long and highly diversified effort which has culminated in the highly refined ?drilling machines we know today, but because of the spectacular possibilities shown by ?detachable bits, and especially those with tungsten carbide inserts, there is little doubt that the cutting face of .the drilling unit has in recent days stolen the spotlight of rock drilling research and commanded the major attention of the rock drilling fraternity. "Solid" Steels Until about twenty years ago, all rock was drilled with a one-piece rod with a bit forged on one end. In the early years of the art of rock drilling, there was tried every conceivable pattern of :bit from the single-edge chisel to elaborate geometric &apos;designs. In the end, it was found that a 4-point bit with two sharpened cutting edges crossing each other at right angles would serve best for most rock drilling requirements. For some years thereafter, the main concern of drill manufacturers was .to obtain the best possible steel for drill rods. This was not accomplished as easily as might be thought. The cutting end had to be such that it could be hardened sufficiently to do its work without premature dulling and yet not so brittle as to shatter under the multiple impacts.

Jan 1, 1951

By W. C. Whittaker

Introduction When one thinks of a coal stripping deposit, the picture that usually comes to mind is that of a more or less flat seam from two to twenty feet in thickness overlain by ten to fifty feet of overburden, in suitable ratio for economic operation. This is the usual type of stripping deposit and is quite a common occurrence in various parts of the prairie provinces. Rather unusual types of coal stripping deposits are being presently worked as open-cut mines by Sterling Collieries, Limited, and the Co al Valley Mining Company, Limited, at Miles 47 and 48 on the Alberta Coal Branch, some 150 miles south west of Edmonton. These deposits are of interest chiefly because they represent turned-up and greatly thickened sections of the Mynheer seam, and as such they present their own problems, peculiar to the commercial exploitation of a seam of this type. The area in which these deposits occur was originally owned by the Pacific Pass Collieries, whose operations, however, were confined to under-ground mining at Lovett, some eight miles to the southeast. It was not until l918 that the value of these deposits was realized, when the Company now known as Sterling Collieries, Limited, opened their pit at Mile 47. At the inception of the work, coal was loaded directly into the railway cars by men using wheelbarrows. In 1920, a tipple was built, after which the coal was loaded by steam shovel into mine cars, hauled by steam dinkeys, and loaded over the tipple into railway cars. In 1922, the Coal Valley Mining Company entered the field at Mile 48, with an entirely mechanical equipment, and at the present rime these two are the only stripping properties in Alberta using mechanical equipment both for the removal of overburden and the loading of the coal. These Companies have operated continuously since that time, and have to date mined and shipped 4,000,000 tons of coal, and moved some 5,255,000 cubic yards of stripping. The present annual coal output for the two mines is about 240,000 tons.

Jan 1, 1935

By V. Gaudreault

Rio Tinto Alcan (RTA) has three smelters that use the Alcoa P155 technology: two in Canada (Grande-Baie and Laterrière, Saguenay, QC) and one in the United States (Sebree, Kentucky). The oldest RTA P155 smelter was built in the 1970s (Sebree) and had an initial current intensity of 155 kA. In the 1990s, RTA installed an amperage booster in Grande-Baie smelter to increase cell productivity. Since then, RTA has continuously pushed the limit of this technology and the target amperage that was 195 kA in 2005 has been increased to 210 kA in 2010.This article describes the successful plant-scale trials to increase current intensity from 195 kA to 210 kA, and the key performance indicator results. It demonstrates RTA&apos;s technology leadership to undertake such a development with its Brownfield smelters.

Jan 1, 2011