Search Documents

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, I. M. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite ore by a pressure acid leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project. The Ambatovy orebody is located in Madagascar. The mini pilot plant testwork was carried out in the Dynatec metallurgical laboratory in Fort Saskatchewan, Alberta. The results of the testwork were very encouraging, including nickel and cobalt extractions in the range of 95.5% to 97.0%, and 94.0% to 97.0%, respectively, in the ore leach step with sulphuric acid. High recoveries of nickel and cobalt were achieved throughout the remaining process steps, yielding separate nickel and cobalt metal powders with better than acceptable purity.

Jan 1, 2005

By J. F. Wright

INTRODUCTION Eighteen years ago about half a dozen experienced prospectors moved from northern Ontario to northwest Manitoba to prospect 'greenstone' areas shown on geological maps of .parts of northern Manitoba prepared by J. B. Tyrrell, D. B. Dowling, and Wm. Mclnnes. Gold-bearing quartz was soon discovered by these men in this new field, and in succeeding years many more prospectors entered the district. A number of the pioneers are still prospecting, and since 1913 mineral deposits have been discovered each year in widely separated areas of the large district extending 150 miles eastward from the 102nd meridian and 60 miles north of latitude 54°30'. The majority of the discoveries, however, have been made near Schist, Elbow, Wekusko, and Kississing lakes. One hundred or more mineral occurrences of some merit are known, the main types being sulphide replacement bodies containing nickel-copper or copper-zinc and gold-bearing quartz veins. Some underground exploration or diamond drilling has been completed on 25 or more of the prospects. Up to the present, three ore-bodies, namely, Flin Flon, Sherritt-Gordon, and Mandy, have been proved. Of these, Flin Flon, the largest, is estimated to contain from 16,000,000 o 19,000,000 tons of copper-zinc ore carrying some gold, silver, and lead. Next in importance in regard to tonnage is Sherritt-Gordon, with a calculated reserve of nearly 5,250,000 tons of copper-zinc ore carrying less than $1.00 combined gold and silver.

Jan 1, 1931

By N. Shi, T. G. Joseph

ABSTRACT: A prototype test dipper (at 1/20th volume and a geometric operating scale of 2.85) was compared during field trials against a conventional dipper with the same tare weight using the same test shovel. Both dippers followed similar dig trajectories, invoked by the shovel operator. A Microsoft® Visual Basic-embedded spreadsheet was used to interpret qualitative visual and quantitative numerical loading data collected on the hoist and crowd dig response. Overall the concept dipper, even with a 50% greater capacity, provided indications of a smoother dig cycle with lower peak hoist loading events and a lower energy per unit excavated.

Jan 1, 2011

By Dorothy Walters

As an increase in the number of producers alters fact ors affecting supply, long-term prospects in traditional markets for many minerals weaken. At the same time, conflicts between national and international objectives undermine existing competitive elements in mineral markets and Canadian costs escalate. Such changes may dramatically alter the environment in which the mining industry operates.

Jan 1, 1979

By Zhang Junzhi

This paper relates cross-border mergers and acquisitions (M&A) risk management theory to actual coal enterprises in China. The 3 phases of M&A are preparation, implementation and integration. By using the Analytic Hierarchy Process and fuzzy evaluation methods, we will try to establish a model to assess risks of the cross-border M&A of China?s coal enterprises. We then apply this model to the case of Yankuang Group acquisition of the Felix Company and receive the assessment results. There are significant reasons for quantitative research on risks of cross-border M&A of China?s coal enterprises, such as effective prevention and risk-aversion, and facilitation of cross-border M&As.

Aug 1, 2013

By T. A. Wedge

This paper suggests a crude correction for the impact of raw material quality on factor productivity in the Canadian mining industry. Such a correction would give a figure more dependent on the changing efficiency of the use of labour and capital, and less dependent on the effects of unquantified changes in inputs.

Jan 1, 1973

By K. Lascelles

ABSTRACT Nickel compounds vary significantly in their toxicological properties, so it is critical that continuing studies to accurately quantify worker exposures consider the processing that accompanies refining nickel-containing materials. The Clydach nickel refinery, which has operated for more than 100 years, was the first nickel-producing facility to show a high risk for lung and nasal-sinus cancers among workers employed since it opened in 1902. Process chemistry and equipment have changed dramatically over Clydach’s history. This paper describes the processing evolution at Clydach with a focus on the propensity for aerosol formation and the forms of nickel in airborne dusts.

Jan 1, 2013

By W G. Brese

The attention of the world is being focused on the spectacular rise of elemental sulphur production in Alberta. In the short space of a decade, production has increased from less than 10,000 long tons, in 1952, to al-most 1,000,000 long tons in 1962. Moreover, 1963 sulphur production is expected to rise by 50 per cent to approximately 1,500,000 long tons, and further increases are forecast for ensuing years. The reason for this dramatic in-crease in elemental sulphur production, particularly in the last year or two, is that Alberta elemental sulphur is recovered in association with the production of sour natural gas. When very large volumes of natural gas began moving to U.S. markets in the latter part of 1961, the resultant increase in sour gas production led to a marked increase in the production of sulphur. Consequently, Canada, mainly on the strength of sulphur produced in Alberta, will soon become the second largest producer of sulphur in the Free World

Jan 1, 1963

By D. G. Tisdale, W. Curlook, J. M. Toguri

"In this study, the vapour phase reduction of titanium tetrachloride conforms to the traditional Kroll chemistry, but employs argon as an inert carrier gas and requires a higher reaction temperature of 1150°C to 1250°C. A vapour phase reaction is advantageous because titanium is the only condensed phase present, and the metal can be collected free of magnesium or magnesium chloride, in marked contrast to the titanium sponge produced by the conventional Kroll process. The yield of metallic titanium from the reaction was determined as magnesium additions ranged from 36% to 168% of the stoichiometric requirement. Yields of over 99% were obtained when an excess of magnesium was present. Although the collection efficiency was low, metallic titanium was collected at the reaction site, where all other species were present as vapours. Magnesium and chlorine concentrations in the collected titanium were less than 0.3%.IntroductionA proposed method (Curlook, 1987) for titanium production has been investigated as an alternative to the conventional Kroll process (Kroll, 1940). The advantages of the new process include a simplified means of recovering the product metal, and a potential for lower overall energy consumption and greater product purity. A higher reaction temperature for the reduction of titanium tetrachloride results in a vapour phase reaction, rather than the conventional liquid phase reaction. This is the major conceptual difference between the proposed and the established (Kroll) processes.This study focussed on optimization of the process chemistry and briefly examined the issue of product deposition and collection. The reduction of titanium tetrachloride with magnesium, to produce metallic titanium and gaseous magnesium chloride:"

Jan 1, 1997

By M. Venkatraman

The limit of Hall - Petch relationship in ultra fine grained steels has been examined based on dislocation pile-up mechanism. When the grain size becomes small the dislocation multiplicity ceases resulting in very low work hardening rate in these materials. An approximate analysis of the theories of hardening indicates that H-P relation is obeyed up to 100nm. It appears that grain refinement is not the suggested approach to improve toughness as well as strength below a critical size.

Jan 1, 2004

"SART technology is a useful tool for improving the economics of gold recovery from certain types of complex gold ores. SART liberates cyanide consumed by base metals such as copper, zinc and nickel, and enables the newly freed cyanide to be recycled to precious metals leaching while producing high-grade base metal sulphide concentrates for sale. The benefits of SART include the reduction in cyanide consumption, avoidance of cyanide destruction costs, minimization of risks of environmental non-compliance due to residues of cyanide destruction reporting to mine effluents, and generation of extra revenue from the sale of base metal concentrates. Concerns with SART typically include uncertainties around capital and operating costs and proper integration of SART into the overall metallurgical flowsheet. This paper presents two case studies addressing these concerns. The first involves actual costs of the full scale SART integrated into a gold heap leach operation and treating up to 500 m3/hr of leach solution at a mine in Mexico. The second involves field pilot testing and a preliminary cost estimate for integrating SART into a silver mine in Peru using Merrill Crowe.INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes in traditional gold extraction metallurgical flowsheets. One of the tools available to the industry to help deal with interferences of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle. Although SART is a commercially available technology, it is still relatively new to the industry. Fewer than ten (10) full scale plants have been constructed in the past couple of decades. Some of these SART plants are small, most are located at remote sites, and the majority have not operated on a continuous basis. This has resulted in a general lack of information in the industry about the true costs, operability and metallurgical performance of SART. BQE Water has been involved in the design, construction, commissioning and operation of large scale SART plants in Mexico, Turkey and Chile and has conducted field testing programs as part of the technical assessment of SART integration into various metallurgical circuits. Having built and operated numerous plants utilizing selective sulphide precipitation of heavy metals, BQE Water has gained unique insight into the design and control of the sulphidization stage of SART to minimize costs and ensure high efficiency in cyanide recovery."

Jan 1, 2017

By B. A. Monkman

"IntroductionONE OF :THE most effective methods by which the construction industry is combatting mounting building costs is by making increased use of lightweight materials, thus reducing the dead load to be carried •by structures. This applies to non-metallic materials as well as to metallic ones, and particular attention has been given to developing lightweight aggregates for use in concrete.The use of lightweight aggregates is not new and, in fact, dates back to the Roman Empire, when pumice was used in the walls and domes of the Roman buildings. More recently, and up to a decade or so ago, the demand for these aggregates was met from deposits of volcanic cinders, pumice, scoria, etc., and from the by-products of blast furnaces and coal burning boilers. However, these sources of supply are no longer sufficient to meet the demand, for transportation costs pretty well restrict the use of the natural lightweight aggregates to the western cordillera regions where the deposits of these materials occur, and the use of expanded slag aggregates to the areas neighbouring the plants where slags are produced. As for cinders, the supply has been greatly reduced by the conversion of industry to fuel oil, natural gas, and powdered coal, and the large stockpiles which existed previously have been pretty well exhausted.Industry's approach to the problem of a decreasing supply, in the face of an increasing demand, has been characteristically direct. The solution has been to construct plants whose sole .purpose is to produce economically an acceptable light-weight aggregate from materials close at hand."

Jan 1, 1955

By D. W. Boydell

The response of reclaimed gold tailings to acid leaching was investigated in the laboratory, followed by a pilot-plant program in which the operations of CCD, CIX and SX were tested with plant feed material. These results formed the basis for the design of the extension to the existing uranium plant at Blyvooruitzicht Gold Mine, commissioned in July 1977. This circuit consists of slimes-dam reclamation by bucket-wheel excavator at a rate of 100,000 t solids per month, acid leaching in pachucas, a five-stage CCD washing section, two parallel C1X absorption columns and two elution columns, SX and an ADU precipitation section. Barren solution is recycled to the CCD section as wash and to the repulper at the slimes dam. The performance of the plant during the first year of operation is compared with the predictions on which the plant design was based. Rated capacity was achieved within three weeks of start-up at a nominal dissolved uranium recovery in the ion-exchange section of around 98%. Owing to recycle, the over-all recovery in the ion-exchange and solvent extraction sections is somewhat higher than this figure.

Jan 1, 1979

By J. C. O'Rourke

"This paper presents an overview of Alberta Oil Sands Technology Research Authority's in situ oil sands recovery project at its underground test facility near Fort McMurray. It covers the rationale for horizontal wells drilled from tunnels below the oil sands, the tunnel layout, the drilling program, and the recovery process and facilities. INTRODUCTIONThe Alberta Oil Sands Technology and Research Authority (AOSTRA) has constructed an Underground Test Facility (UTF) in the Athabasca oil sands deposit in northern Alberta, approximately 50 km northwest of Fort McMurray (Fig. 1). The facility initially is to serve as an underground laboratory from which to field test new approaches to in situ recovery of the bitumen (oil) in the Athabasca deposit.The UTF employs mine access to get at the effective exploitation of an oil reservoir. It does so, however, under conditions considerably more difficult than those faced by most other applications of the technology. Because of the unconsolidated nature of the McMurray formation, the development of drilling chambers directly in the reservoir would be prohibitively expensive. Further, mobilization of the extremely viscous bitumen requires intensive steam stimulation with the attendant concerns of large, complex well completions and potentially hazardous operations Over-all, the oil sands presents mining, drilling and operations challenges which push the technology to a new state-of-the-art. The UTF as it now exists consists of:• a 20 000 ha lease with all-weather road access;• 925 m of 5 m by 4 m tunnels in the limestone 15 m below the oil sands at roof depth of 178 m below the surface (Fig. 2);• two 3 m diameter steel lined shafts to a depth of 213 m;• administration and sur face mine support facilities from which to operate the UTF (Figs. 3 and 4);• underground piping systems to transport drill fluids, steam, produced fluids and services to and from the future well heads underground (Fig. 5);• surface steam generation and production handling facilities (Figs . 3 and 4).• a drilling rig and auxiliary systems specifically designed to drill long horizontal wells into the oil sands from tunnels in the underlying limestone (Fig. 6);• an experienced staff to engineer and operate the facility (Fig. 7)"

Jan 1, 1989

By D. Moronkeji, R. Maharidge, D. A. Curry, B. J. Davis, U. Prasad, J. Franquet

"Proper shale characterization is crucial in shale gas drilling, exploration, completion and production. Unlike porous sandstone and carbonate reservoirs, the challenge with shales comes from their micro- to nano-darcy permeability ranges and the anisotropy of their mechanical and hydraulic properties. Most porosity-dependent logs are not sensitive enough to capture the true behavior of shales. Consequently, mineralogy and other strength and stiffness-related properties must be determined to characterize magnitudes and variances in shale mechanical and flow properties. In addition, these properties must pass quality assurance/quality control (QA/QC) practices to give confidence in their use in subsequent log calibrations, during geomechanical modeling, or in fracture design models. This paper presents a technique to integrate shale properties that are measured by various methods, and a methodology to perform QA/QC on the data before application.Shale properties originate from various sources, including downhole and laboratory measurements. Physical samples for laboratory testing are usually limited to a few depths. Lab tests are often costly, and replicating in-situ conditions can be difficult or impossible. In addition, results frequently show wide scatter, reflecting inherent depth variability and lateral heterogeneity. Wireline logs provide nearcontinuous data, but rarely yield direct measurements of rock strength properties. Although geomechanical and fracture models use log data, calibrating it with reliable and previously verified lab-measured properties is important. This paper presents a process to perform QA/QC on lab-measured data using various crossplots.Ten mechanical, microstructural and physical properties are graphically displayed to visually characterize shale strength behavior in ambient and in-situ conditions, whether measured or modeled statically or dynamically. These properties are often sourced from different departments. The properties are integrated but are individually subject to the previously mentioned uncertainties. Pairs of property values are crossplotted and compared with correlations from the literature or previously established with qualified data from related formations. Conformance with these correlations gives confidence in the data, whereas outliers are flagged as questionable. Repeating the process with questionable data crossplotted against other parameters for the same depth highlights the property with the greatest uncertainty. The determination of its value is investigated to locate the source of the inconsistency and establish a more reliable value. Where this is not possible, the user has a rational basis for rejecting that property value."

Jan 1, 2015

By L. M. Dwarkin

Introduction Avital factor in the success of any coal mining operation is the method of roof support employed. A coal seam in? place has been described as the filling in a geological sandwich and the process of mining as the art of snatching the filling from the midst of the sandwich. The difficulty of this task can be appreciated -in the realization of the tremendous weight bearing on a coal seam due to overlying strata; a weight that can exert pressures of several thousand pounds per square inch. Over the years that mining has been carried on, methods have been evolved by arduous trial and error, making possible the successful extraction of billions of tons of coal. However, these time-proven methods are not enough. The constant demand for faster and cheaper production, the necessity of mining under increasingly difficult conditions, and the requirement for higher standards of safety, call for ever better and more efficient roof support. A recent and very promising development in answer to this need is that of Roof Bolting. Roof Support in General Before proceeding to the subject proper, a brief discussion of the older roof support methods is of value in illuminating the difficulties involved and the problems to be solved.

Jan 1, 1951

By T. Patching

"THE FOLLOWING notes on coal mining in the Edmonton city area are based, in the main, on scattered reports and accounts as little coal mining has been done in this area for about 20 years and few people are left who were involved in what was at one time an important industry of northern Alberta. Although coal mining is not likely to be permitted in the city area itself in the future, a record of this work is warranted to indicate the ·conditions and problems that may be encountered if underground mining again is proposed in the district in the same geological formations and in similar strata. Coal mining in the Edmonton area developed with the influx of settlers in the latter part of the nineteenth century and the first part of the present century. Probably local coal was used by the Fort's blacksmith as early as 1841, and the early settlers probably were 'gopherholing' into the outcrops along the river banks by the 1870s. The first report of commercial coal mining was in 1880 when a contract was let by the Hudson's Bay Company for the provision of 300 tons. As the population in the city and northern parts of the province grew, many new mines were opened along the river and in the district, and coal was even shipped by barge to points in Saskatchewan(1 ,2) By 1909 the Department of Public Works reported that 'Edmonton stands as the second largest domestic coal producing centre in the province'. It continued to hold this position until 1942. From about 1912 to 1951 annual production from mines in the city and surrounding district ranged between 0.38 and 0.65 million tons, depending on weather, wars and strikes. Production began to decline in 1951 because of the increasing availability and consumption of natural gas which was piped into the city and then provided to other towns and rural areas in the northern part of the province. Taylor noted that between 1880 and March 1970, when the last mine within the city area closed, the total of mines and prospects within the Edmonton city area rose to 153. Most of them were small; not more than 20 produced more than a quarter of a million tonnes during their entire life, and only three produced a million tonnes or more. As described by Taylor ""within the city district workings extend discontinuously from the apex of a narrow triangle near Groat Bridge to the base of the triangle in the Clover Bar area"". The larger mines were in this latter area. Approximate locations of the old mine workings in the city are shown in Taylor's atlas. A number of other coal mines were worked in the Rabbit Hill, Big Island, St. Albert, Namao, Cardiff and Morinville districts around the city."

Jan 1, 1985

By P. C. McLeod

THE GECO OREBODY, located north of lake Superior in the Thunder Bay district of northern' Ontario, was discovered in 1953. Diamond drilling in the following year indicated a 15,000,000-ton ore-body, and production plans were made for the shipment of copper and zinc concentrates in three years. To accomplish this, the Geco Project was initiated. The property was in an undevdoped, inaccessible area, and the project involved the conversion and extension of a logging road to the property, the construction of two railways and seventy miles of hydro transmission line, the erection of a municipality, the building of a plant, and the development of an underground mine to produce 3,300 tons per day. This paper describes some of the methods used in the underground development phase of the Geco Project.

Jan 1, 1958

By R. Rumpold, J. Antrekowitsch

"The continued increase of the automobile production leads to a higher platinum, palladium and rhodium (PGM) demand. Due to the high value of the PGMs the recycle of these metals from automotive catalysts is of special interest. Pyrometallurgical processes, which are only focused on the PGMs, represent the state of the art of automotive catalysts recovery. However, hydrometallurgical recycling processes offer additional recovery of other valuable metals and compounds. The method presented in this paper is based on a combination of hydrochloric acid and hydrogen peroxide to dissolve the valuable metal fraction which can be precipitated afterwards.INTRODUCTIONPlatinum and the corresponding metals from the PGM group, especially palladium and rhodium are well known as catalytic active materials. They support chemical reactions which are inhibited. This effect is used to decrease the amount of harmful compounds like hydrocarbons, carbon monoxide or nitrogen oxides in automotive exhaust gases. The generation of these toxic substances is based on incomplete combustion, which in turn is caused by non-ideal conditions in the combustion chamber. Catalytic converters minimize the harmful compounds by supporting the following Reactions 1 – 3 (Votsmeier et al., 2009).CO + ½ O2 ? CO2 (1)CnHm + (n + ¼ m) O2 ? n CO2 + ½ m H2O (2)2 NO + 2 CO ? N2 + 2 CO2 (3)Platinum and palladium are very effective for the oxidation (Reactions 1 and 2), while rhodium supports the decomposition of nitrogen oxides by carbon monoxide (Votsmeier et al., 2009). The classical three way catalyst was a platinum – rhodium combination with a Pt:Rh ratio of 5:1 (Hagelüken et al., 2005). Today the platinum, palladium and rhodium ratio is highly variable and strongly depends on the engine type as well as on the car producer. Diesel engines are operated with a super stoichiometric air addition in comparison to spark ignition systems. Therefore the exhaust gas composition and off gas temperature is different. Based on the high oxygen amount, diesel engines produce less carbon monoxide and hydrocarbons but more nitrogen oxide in contrast to gasoline engines. This leads to various requirements for the catalytic converters."

Jan 1, 2012

By R. M. de Carvalho

Empirical and phenomenological models of SAG and AG mills have dominated the scene for the last few decades, being used nearly every time a mill is scale-up or an attempt is made to improve its performance. However, in spite of their success, these models fail to describe the details of both the grinding environment and the breakage mechanisms. The result is a generally good track record, with a few – but very important – instances when these models fall short in their predictions, which can be very costly. Further, nearly all of these models require detailed calibration to industrial and pilot plant data, being costly in their application, although still with limited predictive capabilities. Recognizing these challenges, a new model framework has been proposed which overcomes the limitations of currently used models by coupling the microscale population balance model, the discrete element model and functions that describe internal classification at the mill grate. This model framework has already been applied to describe breakage in ball mills, with showing very promising results. However, in the case of SAG and AG mills a much greater level of complexity is involved in the model, given the interaction between the mechanical environment that is formed totally or, in part, by the ore itself, and the breakage response in the mill. The paper describes the model framework, demonstrating how it can address appropriately effects such as mill speed, mill filling and size distribution, on the response from the mill. Some of the advantages of the model are related to its intrinsic multi-component and dynamic nature, which allows simulating appropriately mixtures of ores of different competences in a transient manner.

Jan 1, 2012