Search Documents

By G. A. Kosick, M. Freberg, L. A. Kuehn

"Highly variable and higher than forecast lead miff feed grades were problems experienced at the Polaris Concentrator. Limited flotation capacity and poor operating flexibility prevented the plant operators from overcoming these difficulties, and resulted in grades and recoveries which were lower than necessary.Two column cells were integrated into the lead circuit in an effort to give the operators the tools they required to achieve the best grades and recoveries possible, regardless of the miff feed grade. Installation of the column cells increased lead concentrate grade from 76% to 79.3% Pb, and increased lead recovery from 9/% to 91.3% Pb.This paper reviews the design, development and operation of column flotation cells in the lead circuit at the Polaris Mine.IntroductionThe Polaris Concentrator was constructed in 1980 on a barge in Trois Rivieres, Quebec, and towed to its pre sent location on Little Cornwallis Island, Northwest Territories, about 1450 km from the North Pole. The plant presently treat s about 2800 mtpd of new feed with average feed grades of 3010 Pb, 13% Zn and 5% Fe. Current production averages 36 000 tonnes of lead concentrate and 220 000 tonnes of zinc concentrate annually.The barge design and min e location dictated that the concentrator .be compact with very little unused floor space. As a result, flexibility was limited in terms of expanding the plant.Mill feed grades were highly variable and above forecast and the lead flotation circuit was found to be under capacity. This caused continued overloads in the lead cleaning circuit, resulting in low concentrate grades and recoveries. It was evident that an increase in lead flotation capacity and flexibility was necessary. The existing floor space did not allow for the installation of additional conventional flotation cells, but one alternative was the installation of column cells."

Jan 1, 1988

By S. Nafisi

Permanent mould casting may be regarded as a near net shape manufacturing process where simple to very complex shaped engineering components are fabricated with high degree of precision in a metallic mould, In this group, High Pressure Die Casting (HPDC), have attracted more attention because of its production rate, where both liquid and semisolid metals (SSM) can be cast with high degree of precision and versatility. The SEED process, Swirled Enthalpy Equilibration Device, the new process for semi solid metals slurry production route, consists of two steps: The initial step involves extracting specified amount of heat from the molten metal to generate liquid-solid slurry, i.e, mushy structure, followed by drainage of remaining liquid to produce a compact free standing feedstock for rheocasting operation. In this paper, microstructural evolution during the process and some initial casting results of automotive components an also reported.

Jan 1, 2005

By Michael Magerstädt

Material loss by abrasion of contact surfaces of pipes, chutes, pumps, and other equipment in contact with ore is one of the main reasons for downtime of mining operations. Abrasion protection materials in use range from expensive tungsten carbide overlay to hardened steels, ceramics, as well as polymers, particularly polyurethanes (PUR). This paper describes abrasion protection products made from High Performance Polyurethane Elastomers. An interior pipe coating was developed that exhibited outstanding abrasion resistance and an extremely high adhesion to steel. Years of field testing in oil sands tailings as well as applications in slurry lines (e.g., phosphate slurries) have proven the performance of this material. A proprietary field joining process was developed and successfully applied in the field. This joining process requires only one field weld per joint very similar to the joining of uncoated pipe. No internal re-coating is necessary adding savings during pipe laying to the significant savings of reduced down time. Using the building-kit chemistry of polyurethane synthesis, similar high performance elastomers were used to extend the life time of ball mills. An intelligent system was developed in which wear parts contain sensors reporting the actual wear thereby optimizing maintenance interval leading to significant cost savings for the operator. Test data as well as field experience with High Performance PUR Elastomers for abrasion protection in mining are presented.

Aug 1, 2013

By Jennifer Abols

In July of 2013, Lundin Mining acquired the 2,000 tpd Eagle nickel and copper project from Rio Tinto. The project had been put on hold earlier in the year and construction was approximately 50% complete. Lundin immediately accelerated project activities and by September of 2014 the project was constructed, commissioned and ramping up. The newly commissioned facilities went on to reach design throughput, recovery and product quality targets by the end of the year. This was accomplished ahead of schedule and below budget despite numerous obstacles including the worst winter on record in the past 50 years for the area. What led to the success of the project, and in particular the commissioning phase of the project? This paper takes a high level look back and provides an overview of the methodology used, key issues encountered and lessons learned to answer this question.

Jan 1, 2015

By Samuel B. Rombeger

The behavior of gold in hydrothermal systems is evaluated as a function of pH and oxygen and sulphur activities at temperatures to 250°C. Under conditions of stability of pyrite and argillic alteration as emblages, gold will be transported as bisulphide complexes. In systems containing significant amounts of arsenic, thioarsenide complexes may be important. Oxidation, dilution and reduction in sulphur activity would cause gold deposition from saturated solutions under these conditions. Gold chloride complexes will predominate under oxidized conditions where hematite or other oxides are stable and depo ition would result from increase in pH and/or reduction . Absorption and coprecipitation are po sible mechanisms of deposition for gold in certain low grade depo it . Low concentrations of gold in the transporting solution combined with the ignificant solubility of gold as bisulphide complexes, sugge t hydrothermal solutions rarely may be saturated with gold and coprecipitation with sulphides may be an important initial depositional process. Recrystallization of the sulphides in the presence of the hydrothermal solution would be re ponsible for release of gold to more table ite . Thi mechani m i supported by the close association of gold with pyrite in many hydrothermal gold deposits.

Jan 1, 1986

By Fabio Mielli

In these times of increasing costs and diminished returns, energy consumption is one source of savings that remains relatively untapped in the mining sector. Typically, 15% to 40% of operational costs can be attributed to energy in mining operations. This ?process variable? is a complex, multi-faceted variable that involves government regulations, societal pressures, cost and competitiveness. A mining company able to successfully embrace an energy efficiency program is more often than not a successful mining company. Production optimization programs, relatively common today, provide increased production, increased availability of assets and, in many cases, improved quality. They generally ignore the energy question altogether. Production Energy Optimization combines reductions in energy consumption with production improvements to reduce the cost per unit of production while improving emissions reporting. An energy strategy in mining and mineral processing operations is a critical component of Production Energy Optimization. This strategy must support the financial and operational integrity of the business. Developing a successful energy strategy requires a well structured approach such as following: ??Understanding where energy is being used and why, ??Recommending and implementing energy conservation measures, ??Driving visibility to targets and results, ??Re-evaluating continuously. The objective of this paper is to help you better understand the process, tools and technologies that enable mining organizations today to address energy and sustainability issues more tactically and proactively.

Aug 1, 2013

By Nicholas J. Welham

"The effect of extended ball milling has been studied for two industrial processes: (1) the processing of metal sulphide concentrates; and (2) the carbothermic reduction of ilmenite to synthetic rutile. The plant concentrates were a gold ore with 128 g/t Au of which 8% was non-refractory and a zinc concentrate with copper impurities.The gold concentrate showed complete dissolution of the gold bearing minerals after milling giving almost complete gold liberation. The zinc concentrate showed almost all of the sulphides had solubilized leaving the gangue and elemental sulphur. A study of pure pyrite and arsenopyrite shows that selective dissolution should be possible by a simple leaching process directly after milling.The milling of ilmenite and coal together results in a temperature decrease of 150°C in the subsequent carbothermic reduction of ilmenite, in addition to improving both the rate of reaction and the selectivity of reduction to rutile. IntroductionAlmost all mineral processing plants use mills for the size reduction of particles prior to physical and chemical processing. When continuing beyond size reduction the energy transferred causes deformation, breakage and realloying of particles giving a steady-state particle size. The breaking also causes increasing damage to the crystal structure by formation of smaller grains giving an increasing number of grain boundaries and increasing crystalline defects due to deformation. The increasing number of grain boundaries and defects leads to increased reactivity, which can be seen directly by a reaction within the mill, or indirectly, via a decrease in the subsequent annealing temperature required for reaction."

Jan 1, 1997

By M. G. Manzone

Approximately two-thirds of the annual 210,000 tons at copper refined by AMAX Inc. at the United States Metals Refining Company in Carteret, New Jersey, comes from a wide variety of copper scrap ranging from low-grade smelter scrap to wirebar-grade material. The equipment and methods used to effect such large-scale metal recycling in an urban area and the measures taken to collect and recover metal values from smelter and refinery byproducts while protecting the environment from pollution are described and discussed.

Jan 1, 1977

By Ken McIntyre, Trodel Wolf-Dieter

"Sirius Minerals is a UK based fertilizer development company focused on advancing into operation its polyhalite project in North Yorkshire, England. The operation is known as the Woodsmith Mine which has an estimated 2.7 Billion Tonnes of reserves and is currently in the construction phase. DMC Mining Services was selected to carry out the construction of four shafts for the project, a production shaft of 6.75m diameter to a depth of 1594 m, a ventilation shaft of 6.75 m diameter to a depth of 1565 m, and two additional shafts to support the construction of the material transport system (the MTS and Lockwood Beck intermediate) to 360m in depth for servicing the underground conveyor network for transport of product from the mine site to the costal port facilities located at Teasside. This paper will review the status of the project to date and the innovative approaches that DMC is utilizing to ensure a safe and successful shaft sinking project. INTRODUCTION The Woodsmith Mine in North Yorkshire is a Sirius Minerals-owned deep potash and polyhalite mine located near to the hamlet of Sneatonthorpe, Whitby in North Yorkshire, England, approximately 75 km east of York. The area of interest is more than 700 km2. The £3.2 billion project is to develop the Woodsmith Mine to extract polyhalite, and a tunnel system to transport it to a materials handling facility and harbour at Teesside. The site is the world's largest and highest-grade deposit of polyhalite and is expected to produce 20 million tonnes of polyhalite, potash and POLY4 per annum, as well as create over 1,000 direct jobs and many more indirectly. It has the potential to generate over £2 billion of annual exports for the UK. As the project will require mining to be undertaken in the North York Moors National Park, many objections were raised about the mine. Sirius Minerals has gone to great lengths to ensure that the project is sensitive to the local landscape, including: mineshaft head frames that will be positioned below ground to reduce their visual impact; surface buildings will be kept to a minimum; and the entire site will be landscaped and screened by existing woodland to blend in with the surrounding area. The project will also abide by strict environmental limits which govern our activity during the construction phase."

Jan 1, 2019

By F. T. M. White, W. A. Bardswick

"The parameters of airborne minerallic particulates which create industrial dustiness, together with the physiological hazards caused by their inhalation, are reviewed. Various techniques of dust sampling are discussed and analysed, and the parameters referred to above are classified as the basis for methods of assessing the physical, chemical and mineralogical characteristics of dust-particle suspensions. The paper surveys those methods of assessment currently accepted by various statutory authorities, and reviews other methods that warrant attention and newer techniques that are being developed."

Jan 1, 1969

By Charlie Jefferson

Main Goal: Resource Assessment 1. Incorporate existing data & results, old process. 2. NEW Quantitative Analysis (Chung and Chen) 3. Try mass balance of U and geochemical tracers 4. Use holistic process approach ?with key foci ?Targeted basin / belt assessments ?Is there as much in the Athabascaas they say? ?Athabasca reference for other basins (Thelon, etc) ?Compare sandstone & volcanic with USA, Kazakhstan etc: do their models apply here? ?Which IOCG systems are prospective for uranium? 5.Consider Groundwater, Environment; 6.Communicate

May 1, 2006

By D. F. VanDine, H. George

"The possibility of spoil pile failure at the Kara Kara bauxite strip mine, Guyana, South America, is of major concern to the mine operators. The current mining technique requires the continuous operation of an 11 ms bucket capacity walking dragline on top of 18 metres of freshly spoiled uncompacted overburden material consisting of varying mixtures of kaolinitic clay and quartzitic sand. A field biased geotechnical study of undisturbed overburden and corresponding spoiled material has identified site-specific, non-linear correlations between vane shear strength, standard penetration resistance and spoil pile composition. Readily available geological exploration borehole logs has enabled a composite clay isopach map of the entire mining property to be drawn and critical areas to be zoned according to expected slope stability. Stability has been assessed using simple hand calculation techniques. Use of the resulting stability map provides the mine operators with a means of forecasting the need for appropriate preventative measures at varying stages of mine development, throughout the life of the mine.A similar investigation procedure could be employed at many presently operating and future strip mines.IntroductionThe Kara Kara bauxite stripe mine is located at Linden within the bauxite belt of Guyana in South America. The mining property covers a total area of 88 hectares of flat to gently sloping ground of which some forty per cent is being actively mined or being preparatorily stripped of overburden, prior to eventual mining (George and Gordon, 1979). The regional climate is tropic and humid. Temperatures vary from 16°C to 38°C and yearly rainfall averages 2600 mm, with at least 55 per cent of this precipitation occurring during the 'wet season' months of May to July and December to January."

Jan 1, 1983

By Nordau R. Goodman

"IntroductionTHE HISTORY of Nova Scotia's gypsum industry goes back about two hundred years. The extensive deposits found in the Windsor formation, which is Lower Carboniferous, were the first discovered in North America and were known to the earliest .settlers. There has been a steady increase in production from these beds, except for minor setbacks in years of wars and depressions, but at the same time there has been a decrease in the number of operating quarries. This decrease reflects the change from the days of horse-and-cart recovery to the modern, large-scale, highly mechanized operations. In the beginning, almost any outcrop could •supply the tonnage requirements and the most •convenient were selected, but the millions of tons needed to meet present-day needs are not easily found.Despite the size and importance of the Nova Scotian deposits there has been little detailed geological work. Sir Charles Lyell, in 1843 ( 10), established that the beds are Lower Carboniferous and this was confirmed by Sir William Dawson (3) a .few years later. Both Lyell and Dawson agreed the calcium sulphate beds were an original part of a bedded series .but did not consider they resulted from a concentration of sea water. Lyell reached the conclusion that the gypsum was related to volcanic action in the form of heated vapours or hot springs. Dawson believed it was formed by the action •of sulphuric acid on calcium carbonate. The acid, derived from the oxidation •of iron pyrites which was abundant in the older formations, was carried by rivers into basins which were rich in shells."

Jan 1, 1954

By K. Law

"The Hatch Product Transport (HPT) system is a highly flexible and configurable route selection and sequencing system for controlling large bulk material handling facilities. The system has a generic control algorithm that can be configured to suit any material handling facility. It can also be easily reconfigured to cater to plant expansion or modifications without incurring significant disruption to the existing production, costs in testing, and re-commissioning, thus achieving cost savings throughout a facility’s lifecycle.This new material handling control system has been installed at BHP Billiton’s Port Hedland iron ore terminal to facilitate its expansion to beyond 100 Mt output capacity."

Jan 1, 2006

By Robert B. Parsons

"Draft income tax amendments aimed primarily at certain carve-out arrangements prevalent in the oil and gas industry could have devastating results for long standing royally arrangements in the mining industry . Whether or not this potentially damaging effect is intended is largely beside the points-the point is that the mining industry would be well advised to become familiar with the draft amendments and make sure that the potential damage to existing and future royalty agreements is minimized.The draft amendments fail to take into account the nature of mineral royalties and app ear to reflect a lack of understanding of the characteristics of the mining industry.IntroductionOn July 19, 1985 Finance Minister Michael Wilson released draft amendments to the Income Tax Act which are intended 10 effectively thwart the use of so called “carve-out arrangements"".Unfortunately, the proposed amendments are so broad and far- reaching that countless ""innocent"" royalty arrangements in the mining industry, and in the oil and gas industry, are threatened. The potential harshness of the new rules would be compounded by the retroactive application to the amendments to longstanding royalty and similar agreements."

Jan 1, 1985

A direct comparison has been undertaken between laboratory wind tunnel experimentation and computational fluid dynamics simulation of a 3D manufactured analogue for a body of fractured broken rock, created with CAD/CAM techniques. Detailed descriptions of the ?design? of the analogue (using a discrete element analysis multi-body simulator), its manufacture (using computer aided design and 3D printing technology) and the laboratory experimentation (inserting the physical analogue into a laboratory scale wind tunnel) are presented. The agreement of the results of direct experimental observations on the manufactured analogue with the values from CFD simulations of those experiments justifies the utilization of a CFD environment for the practical investigation of geometric factors controlling air flow and heat exchange in complex assemblages of broken rock blocks. The ultimate goal is described, that of developing functional relations between bulk properties of such assemblages (such as their porosity and bulk density) and the low-level geometric factors that dictate the air flow behaviour, such as the equivalent perimeter length of the cross-sectional area available for flow, or average flow path tortuosity. A practical application area of the work in the mining context is also described; equivalent continuum air flow and heat transfer constitutive models developed on the CFD tool from such functional relations are useful in characterization of seasonal heat storage in large scale bodies (approximately 1 km3) of broken rock.

Aug 1, 2013

"Load-haul-dump machines (LHDs) are typically used in underground metal mining operations. Delays or inappropriate use of LHDs can result in production loss. Optimized LHD use is especially crucial in larger mines because longer travel distances increase heat, dust, and gas emissions, which in turn increase ventilation costs. This study, conducted at an existing Swedish sublevel cave underground mine, used discrete event simulation and the AutoMod™ DES tool to determine the ventilation costs related to using too many diesel LHDs in a production area with reduced ore pass availability. When fewer ore passes are available, ventilation costs related to operating LHDs in the production area were found to increase by as much as 200, 224, and 306% for one, three, and six LHDs in operation, respectively. ¦ KEYWORDS Discrete event simulation (DES), Loading operations, Production rate, Ventilation costs RÉSUMÉ Dans les exploitations souterraines d’extraction des métaux, on utilise généralement des chargeurs-transporteurs (LHD, de l’anglais Load-haul-dump machines). Les retards ou l’utilisation abusive des LHD peuvent entraîner une perte de production. L’utilisation optimisée des LHD est particulièrement importante dans les grandes mines en raison des longues distances parcourues, lesquelles augmentent la chaleur, la poussière et les émissions de gaz qui, à leur tour, décuplent les coûts de l’aérage. Cette étude, menée en Suède dans une mine souterraine utilisant la méthode d’exploitation en sous étages avec foudroyage, s’est basée sur la simulation à événements discrets (SED) et l’outil de SED AutoMod™ pour déterminer les coûts de l’aérage liés à l’utilisation d’un nombre trop élevé de LHD alimentés au diesel dans la zone de production, avec une disponibilité réduite de la cheminée à minerai. Lorsque les mines disposent de moins de cheminées à minerai, l’étude montre que les coûts de l’aérage liés à l’exploitation des LHD dans la zone de production augmentent respectivement de 200, 224 et 306 % pour un, trois et six LHD en fonctionnement. ¦ MOTS CLÉS coûts de l’aérage, opérations de chargement, simulation à événements discrets (SED), taux de productionINTRODUCTION Transporting material from the mine face to the dumping location requires flexible loading and hauling equipment that is able to cope with sharp curves and a complex mining environment. Load-haul-dump machines (LHDs) are designed for such an environment. Models are available to suit specific features of the working environment such as small, large, or narrow open stopes (Atlas Copco Rock Drills AB, 2007). When carrying a full load, haulage speed is higher for LHDs than for front-end loaders with the same engine size. Also, payloads are approximately 50% higher for LHDs than for front-end loaders (Atlas Copco Rock Drills AB, 2007). LHDs are capable of climbing steep (Bloss, Harvey, Grant, & Routley, 2011). The haulage distance between stope and ore pass is usually between 50 m and 400 m. LHDs are efficient for tramming distances up to 200 m (Bloss et al., 2011), whereas when loading trucks, the LHDs work efficiently when the distance is less than 100 m (Atlas Copco Rock Drills AB, 2007). The largest diesel-powered LHDs, with drive motors of up to 350 kW, can handle a payload of 21 t (Wennmohs, 2014). Most mining equipment runs on diesel fuel, which provides flexibility, high durability, and high efficiency (Pronk, Coble, & Stewart, 2009); however, other alternatives such as electric, hybrid diesel/electric, or hydrogen fuel cell machines are increasingly being developed and used. This change is due to diesel-powered machines accounting for a significant portion of the ventilation costs in the mine (Chadwick, 2008; Paraszczak, Laflamme, & Fytas, 2013). Currently, as part of the European sustainable intelligent mining systems (SIMS) project, Epiroc AB is planning to demonstrate technology for a diesel-free underground mine at Agnico Eagle’s Kittlä mine in Finland using"

Jan 1, 2019

By Haibin Wang, Zhiwei Huang, Zhixiang Cui, Wenzhao Cui, Zhi Wang

Fangyuan Two-Step copper smelting process was commercialized in October, 2015 and has been operating for 3 years and 5 months. As the unique continuous copper smelting process with simplified flow in the world, production parameters have been significantly improved after three years. In the first half of 2018, the feed rate was above 200t/h, availability reached 97.5%, operation cost was about 20% lower than the conventional three-step processes showing obvious economic advantages. The Two-Step process in Fangyuan is composed of 1 Submerged Lance Smelting furnace (SLS) and 2 Submerged Lance Converting& Refining furnaces (SLCR). Two SLCRs work alternatively to ensure continuous production. High grade and liquid matte from the SLS is introduced to the SLCR by sealed launder to complete converting and refining. The SLCR is an original and independent innovation of Fangyuan, for which Fangyuan completed lots of development and improvement. This paper will introduce the process and experience. INTRODUCTION China is the largest producer and consumer of refined copper. Most of the processes adopted in China are conventional "Three-Step" copper smelting processes, which are comprised of smelting, converting and refining. There exists some problems in the conventional processes, such as high energy consumption, large heat loss, low altitude emission of SO2, etc. To deal with these problems, Fangyuan developed the new copper smelting process with simplified flow, low cost, clean and high efficiency. The SLCR that combines converting and the refining process was also developed, which shortens the process flow from conventional three steps to two steps. The SLCR is of great significance in promoting the development of the copper industry. Development and industrialization of SLCR At present, copper concentrates are treated in three steps: smelting, converting and refining. Anodes are also produced by continuous converting processes such as the Mitsubishi process and the Double Flash process. Problems like matte transportation by ladle, capacity limitation, and low altitude pollution exist.

Jan 1, 2019

By G. F. Vander Voort

Over the past twenty years, steelmakers have introduced improved practices for reducing the inclusion content of steels. The success of these practice changes can be monitored in a variety of ways. Chemical analysis of the bulk sulphur and oxygen contents provides a relatively simple means to assess the impact of these changes. However, microscopical test methods are still needed to assess the nature of the inclusions present. Traditional chartbased measurement methods have wide acceptability, and their data are well understood by both purchaser and producer for heat acceptance purposes. However, these methods do have inherent weaknesses which limit their usefulness for quality control, SPC, and database applications. Image analysis-based chart measurements are an improvement over manually generated chart ratings, but the data still do not lend themselves to databases and statistical comparisons. ASTM Committee E-4 on Metallography has developed a stereologicallybased image analysis standard test method, E 1245, which provides the necessary data in a form which is easily databased and analyzed statistically. This paper describes E 1245 and shows how data from different heats and melting practices can be compared statistically to ascertain valid test differences.

Jan 1, 1998

By K. C. Hendrick

The paper will review the significant developments in world copper over the past ten years and their impact on the Canadian industry. It will also examine the outlook for the future.

Jan 1, 1971