Search Documents

By Isabel C. B Rodrigues, Flávia D. Reis, Versiane A. Leão, Rosa M. F. Lima

Attention has been focused in recent decades upon the precipitation of metal sulphides from acid mine drainage (AMD) and pregnant leach solutions, due to the advantages of the sulphide precipitation process over traditional methods employing hydroxides. The aim of this work was thus to explore technologies for copper precipitation using either Na2S or biogenic sulphide. The recovery of copper sulphide was improved when the initial pH of the solution containing each metal was 4 or excess sulphide was employed. In such, a condition the removal efficiency was 99.9%, corresponding to a residual level of 0.1mg/L for copper in solution. Kinetic parameters for precipitation were determined from the particle size distributions using the method of moments, where the growth and nucleation rates, as well the agglomeration kernel, were calculated. The biogenic sulphide was a suitable alternative to sodium sulphide for copper removal as either sodium sulphide and biogenic sulphide can be utilized to precipitate such a metal allowing the effluent to be compliant with environmental legislation.

Jan 1, 2014

By L. T. Loe, A. S. Norsk, Mo i. Rana

High production rate and good stability demand the optimization of all phases of electric pig iron smelting. This is important with respect to slag chemistry, which to a large extent regulates the process temperature in electric smelting. Controlled basicity and slag volume. and a satisfactory screen analysis of the reduction material and sinter, are of the utmost importance for smooth furnace operation. Large variations in slag volume and in B/ A and C/Fe ratio will have an influence on the furnace resistance and thus the specific energy development in the furnace, which lead to variable reduction of SiO.. The result will be variable hot -metal quality and un-stable furnace operation.

Jan 1, 1970

By Y. F. Jiang, K. Fang, Q. Q. Jiang, Q. Wu

Inter formational sliding of bedding planes between two different rock types in Badong formation is an important reason that leads to the instability and fracture of rock mass in this stratum. There are no specific research achievements on bedding planes between two different rock types in Badong formation. In order to study the shear mechanical properties of bedding planes between two different rock types. This paper using the software of particle flow code (PFC) and JRC model to establish several typical structures of different roughness coefficient of surface morphology based on the laboratory tests on silty mudstone and marlite in Badong formation. A great deal of numerical shear tests were carried out by ball production, radius expansion and servo infliction. The research results are as follows: First, shear strength of Badong formation is found to vary between that of silty mudstone and marlite isotropic planes by analyzing shear strength of the homogenous bedding planes and inhomogeneous rock types, we can find that the shearing strength in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the shearing strength of silty mudstone isotropic planes. Second, the basical friction angle of bedding planes between two different rock types in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the basical friction angle of silty mudstone between isotropic planes. Third, based on the experimental results, an expression is obtained to describe the relationship of the ratio of shearing strength between bedding planes of two different rock types and isotropic planes in soft rock, the rock combination coefficient, and the roughness coefficient. This study has important significance for further research on the shear mechanical properties of bedding planes between two different rock types.

Jan 1, 2015

By G. Scott Zimmer

Mine planning at Cassiar consists of an annual cycle of projection, control, evaluation and revision following completion of annual diamond drilling during the summer months . The inherent difficulty in evaluating fibre grade and distribution, combined with a high-wall phase or push-back mining system, requires continuous modification to designs and schedules based on a cumulative evaluation of equipment performance and prediction versus production. To expedite the planning sequence, a mini-computer system has been introduced which allows emphasis to be placed on optimizing designs, exempting personnel from manual calculations and tabulations.

Jan 1, 1978

By L. Chunpongtong

One of the challenges of mine planning is to determine the most cost-effective replacement time for aging equipment. The lifespan of equipment, such as haul trucks and shovels, deployed in mining operations varies due to the nature of the material and ground conditions in which it operates. For engineering economists dealing with aging equipment, the options become an economic trade-off between higher maintenance cost versus the cost of new equipment. The discount rate plays a significant role in this decision; the higher the rate, the longer the economically optimal lifespan. Therefore, the ultimate question is: ?How can the relationship between the discount rate and the economically optimal lifespan be expressed mathematically??

Aug 1, 2013

By C. L. Monroe

It has been the custom in recent years to look upon Atlin as a worked-out placer camp. This is a conception, however, which is far from the real situation. The placer-gold deposits of Atlin are today, after thirty-one years of continuous working, a field well worth the attention of the mining world. It is true that the shallow diggings (the 'easy money') have been practically cleaned out, but although there have been perhaps ten millions, or more, in gold already taken from the district, there are still many more millions left in the creek beds . A conservative estimate of the gold still remaining in one creek alone, Spruce creek, for a long time known as the 'prospector's meal ticket', would place the amount at anywhere from fifteen to twenty million .dollars, and there are a number of other creeks that have never been thoroughly worked, and some only partially prospected. That the true situation is beginning to be recognized by those who are on the lookout for a profitable field for investment, is born out by the fact that, within the last few years, New York capital directed by Mr. Charles V. Bob, who is also responsible for the opening up of the Engineer mine, has installed on Pine creek, where the first discovery of gold in the district was made, one of the largest hydraulic mining plants on the continent, utilizing six miles of the old hydraulic ditch of the Discovery Mining and Power Company, and over two miles of pipe line. On Boulder creek, where already two millions have been taken out, the Consolidated Mining and Smelting Company are on their third year of development work in opening up the unworked ground, while on Otter creek a newly organized French company have started a plan of development which will involve an expenditure in the neighbourhood of $200,000, and two or three years' work, before they can hope to find gold in paying quantities. It is probably safe to prophesy that placer gold will be produced in the Atlin district for the next fifty years

Jan 1, 1929

By M. Dupuis

It has been previously demonstrated [1,2] that using selective collector bar rodding has a big impact on the uniformity of the current density at the top surface of the cathode block and hence on the intensity of the horizontal current in the metal pad, The present study investigates the impact of using selective collector bar rodding on the MHD stability of a 500 kA aluminium electrolysis cell, For this purpose the recently developed MHD package for the aluminium reduction cell time dependent behavior is used.

Jan 1, 2005

By W. E. Uren

The Dominion Coal Board was created by Statute passed on July 17th, 1947, and was brought into effect by proclamation on October 21st, 1947. It is, consequently, a comparatively young body, having been in existence for only eighteen months. Before dealing with the constitution and duties of the Board, it may be well to answer the unspoken question of why it has been considered necessary to single out coal as one specific mineral requiring the continuous attention of a specially created permanent Board. In Canada, coal has been the neglected sister of the more spectacular minerals and it comes as a surprise co many to note that in 1948 the value of the coal produced in Canada was higher than that of any other mineral with the one exception of gold. Coal touches upon our daily lives in many different places of which the public are not generally conscious. As household fuel, it is a necessity of life in this northern climate; as a source of steam, it provides the heat for most of our industries; it is the food of the 'iron horse' chat shuttles our persons and our goods across the land; it is the source of power in many parts of the country; it is the chemical reducing agent chat, in our furnaces, transmutes the metallic oxides to the virgin metal. Coal is, in fact, the indispensable mineral chat forms the corner-stone of our present structure of industrial civilization. Is it, then, such an odd thing that the provision of an adequate supply of coal should be a matter of national interest or that measures should have been taken by government co provide for a constant watch, by a permanent Board, on the supply of co al? ? The Board is the result of the recommendations of the Royal Commission on coal which made a long and detailed study of the Canadian coal problem. It is composed of a permanent Chairman and six part-time members, most of whom have had intimate contact with various phases of the industry.

Jan 1, 1949

By Timo Heikkinen

We have read, with great interest, Mr. Crocker's article on "Recent Trends in Autogenous Grinding," published in the October issue of The Canadian Mining and Metallurgical Bulletin. Referring to our paper, "Two-Stage Autogenous Grinding Investigations at Outokumpu," we can now report that last August we changed to this method at the Keretti concentrator. Prior to the conversion, the Keretti plant (see flow-sheet, Figure 1) had two primary rod mills, 6 ft. in diameter and 12ft. in length, in open circuit, followed by four secondary 9-by 12-ft. pebble grate mills in closed circuit with rake classifiers. Last summer, wl1en the Since August, grinding has been successfully carried out autogenously in two stages, with two mills being employed in the primary stage and four in the secondary. The size of the pebbles in the secondary mills is about the same as earlier -l V: i to 3 inches (Figures 4 and 5). Also, we generally prefer two-stage grinding to single-stage grinding because, in the former,

Jan 1, 1964

By P. Bramwell, R. Tremblay

"The Port Radium leaching plant of Eldorado Mining and Refining, Limited, produces 450 t./d. of sulphuric acid leach liquor containing l. 73 g. /I. U 308. After solvent extraction, the waste solution is discarded at 0.002 g./l. U30s for a recovery of 99.8 to 99.9 per cent. The solvent is acidified with weak sulphuric acid, loaded to 4.5 g./l. U80:1 in three-stage extraction, scrubbed with water, and stripped with soda-ash solution in single-stage stripping. Caustic removes the UaOs from the pregnant strip solution as a precipitate. The slurry is filtered, re-pulped with water, and re-filtered. The pressed precipitate at 81 to 82 per cent equivalent U30s is dried and packaged. The carbon-ate filtrate is cooled to remove sodium sulphate build-up and carbonated to convert excess caustic. Reagent consumptions are 4.1, 0.22, and 0.39 pounds per 1,000 gallons of pregnant solution for Diesel oil, amine, and alcohol, respectively. Caustic consumption averages 1.3 to 1.4 pounds per pound U3O8.Extraction and stripping is accomplished in sheet-iron mixer-settlers lined with Phenoline. Piping on both circuits is Schedule 80 polyvinyl chloride. Valves are straightway Buna N lined with American Hycar diaphagms. Extensive instrumentation ensures good metallurgy with a minimum of variations and labour. Mixing in a continuous organic medium and careful acidity control are required to minimize third-phase formations. Heating the precipitate slurry is conducive to good filtering in Perrin presses with neoprene-coated, rolled-steel sectors. Sodium sulphate is crystallized from carbonate filtrate solution by batchwise cooling to 54°F. with lake water."

Jan 1, 1959

By W. A. Gow, H. H. McGreedy

It is believed that many of the problems encountered in the operation of gold cyanidation plants are difficult to resolve due to the lack of sufficient and reliable in-formation regarding the variations and actual values of operating variables at any given time. The application of instruments to monitor the more important variables in the cyanidation process should result in more efficient plant operation and a better understanding of the process. The use of pH and conductivity sensing devices for alkalinity measurements, a monitor to determine the dissolved oxygen content of plant solutions, a continuous cyanide titrator and sonic control of grinding circuits are discussed. Although the discussion is oriented toward the cyanide process, much of the paper is applicable to other ore treatment operations.

Jan 1, 1966

By M. P. Sinha, Rashmi, Tata Steel Ltd., S. Jaiswal, A. Bhatnagar, P. Garg

Reagents form a crucial part of flotation process as they have the power to control the surface properties of minerals. In case of coal flotation, collectors and frothers are two the important and commonly used reagents. But other types of reagents such as promoters, modifiers and depressants are also finding wide applications because of their availability to improve selectivity and increase recovery. Because of these chemicals the scenario has changed from flotation being used mostly for high rank hydrophobic coals to low rank, oxidised or inferior coals. In the present work a case is presented in which two non-ionic surfactants (abbreviated as A & B) known to act as emulsifier have been studied to get a better flotation performance for a preparation plant with varying feed characteristics. Laboratory flotation tests were conducted with both the surfactants using three feed samples of the plant by varying the dosage at three different levels. The highest combustible matter recovery (more than 80%) was obtained for surfactant B at a dosage of 75 ppm (parts per million) for feed 1. But at the same dosage the recovery decreased by 21% and 10.2 % respectively for feed 2 and 3. On the other hand surfactant A showed a consistent result for all the three feed samples giving the highest value at a dosage of 50 ppm followed by a decrease beyond this point. The tests were complemented by contact angle measurements that demonstrated the same trend. In addition to this the reproducibility of data for Surfactant A was checked and found that the standard deviations for both separation efficiency and combustible matter recovery were within the permissible range (less than 5%). Finally an in-plant process optimization study to evaluate the performance and applicability of surfactant A at industrial level was done and has been discussed.

Jan 1, 2016

By F. H. Wheeler

CONSIDERING the nature of this audience, I perhaps, in addressing you on the subject of air transportation as related to the mining industry, should speak with tongue in check or at least with some reservation. I know full well that many of you, veterans in the great mineral development in Canada, are perhaps more conversant with the overall aviation picture than I, for aviation to you has been the means to an end, and in many instances has been part and ?parcel in the success of your particular projects, in the form of the initial means of transport. I feel, however, that we in this room today have somewhat parallel geographic interests - yours in relation to what is in the ground, mine in the air - and also in the forests and in the streams - aviation, hunting, and fishing - things which have occupied my attention practically all my adult years. In the light of what has gone. before, and in view of present developments, I think you will agree with me when I say that I do not think there could be a more intriguing pursuit than playing a hand in rolling back Canada's tremendous northern frontiers, even if, at this stage, we have made but slight impression on the untold opportunities which lie in our wide-spread, undeveloped areas.

Jan 1, 1956

By Michael Harley, E. Guy Charleworth

"Bedding-parallel thrust-hosted gold veins are developed in the Sabie-Pilgrim's Rest goldfield, eastern Transvaal, South Africa. The reefs display a complex history characterized by temporally and spatially overlapping events of similar mineralization and deformation. Recognition of the episodic reactivation of these low angle (5° to 10°) thrust faults implicates high fluid pressures (equalling or exceeding lithostatic pressures). Geochemical constraints limit the amount of fluid-rock interaction and the occurrence of transgressive mineralization within the Archaean granitoid basement suggests that the high pressure fluids originated at depth beneath the Transvaal Basin.Similarities exist between gold deposits of Sabie-Pilgrim's Rest and Telfer, Western Australia as well as Passagem de Mariana, Minas Gerais, Brazil. All deposits are sub-parallel to the enclosing bedding which is shallowly inclined. Furthermore, they are also hosted by contractional deformational structures and are clearly epigenetic in origin."

Jan 1, 1994

By C. R. Julian

THE large pyrites ore-bodies, the underground mining of which is to be described, are situated at Rio Tinto in the Province of Huelva in Southern Spain. The situation of the different ore-bodies with relation to one another is shown in Figure 1. It will be seen on the plan that the strike of the ore-bodies is approximately east and west. The geology of the district has been very fully described by Dr. D. Williams (1), so that for the purposes of this paper it will be sufficient to give briefly the salient features o each of the two larger ore-bodies which are being mined by underground methods at the present time. (a) San Dionisio.-This ore-body is the largest single deposit in Rio Tinto, having on its upper levels a length of 3,500 ft. On the upper levels the average width is approximately 200ft. but in places on the lower levels there is a width of 900ft. of un broken pyrites. Diamond-drill holes, without running out of ore, show the ore-body to persist to a depth of at least 1,600 ft. The ore-body in the upper part lies between slate and porphyry walls, but in depth is enclosed in porphyry walls. (b) South Lode.-Faulting is considered to be responsible for the break in the solid ore between South Lode and San Dionisio. On the upper levels, the South Lode ore-body has an unbroken length of 4,000 ft. The massive pyrites has a maximum width of 300ft. and an average of about 100 ft. Ore has been proved to a depth of 1,000 ft., at which depth the ore-body is much reduced both in length and breadth. This ore-body, to the depth at which it has been proved, lies entirely between slate and porphyry walls. The South Lode and the San Dionisio ore-bodies are mined both by open-cast and by underground methods. There is evidence that these mines have been exploited intermittently during the last 3,000 years; but, as is to be expected, no records are available of the tonnage mined prior to the time of purchase by the present company.

Jan 1, 1940

By W. H. S. McFarland

THE Yukon Consolidated Gold Corporation, Limited, a Canadian company, operates alluvial gold dredges in the Klondike goldfields of Yukon Territory. Its operations are of unique interest to Canadian mining as it is the only large-scale placer mining operation of this type in Canada. Its properties lie in the valley of the Klondike river and its tributaries, Bonanza, Hunker, Bear, Last Chance, and All Gold creeks, and in the valley of Indian river and its tributaries, Dominion, Gold Run, Sulphur, Eureka, Montana, and Quartz creeks. At the end of 1938, they consisted of 1,650 placer mining claims and 9 leases or concessions. They cover a belt with an area of approximately 1,000 square miles. This vast area covers in part claims which have been previously worked by other methods such as 'drift' and 'open-cut' mining, and areas which were too low grade for such methods. The ground held by the Company is not held in freehold but in the form of mining claims and mining leases granted by the Dominion Government under the provisions of the Yukon Placer Mining Act. Full-size creek claims are 500 feet in length by 1,000 feet on either side of the base-line. Hill and bench claims are 500 feet up and clown the valley and 1,000 feet at right angles to the valley. All claims are held on the basis of an annual renewal fee of $10 for each claim plus 'representation work' of an assessed value of $200 per claim per annum. For the purpose of such representation work, claims may be 'grouped'. This means that work done by one dredge is sufficient to 'represent' a comparatively large block of claims. It is only in this way that it becomes possible to consider operations on a large scale over a term of years, for such operations would obviously be impossible on law-grade ground if representation work had to be done separately on each individual claim in each year.

Jan 1, 1939

By H. W. Smith, N. Ichiyen

A convenient method for the calculation of metallurgical balances, based on statistical treatment of all available data, is presented. An error analysis is included. Examples show the advantages of the method, and also that such balances are less precise than might be supposed.

Jan 1, 1973

By Selwyn G. Blaylock

I.-THE HISTORY OF THE SYSTEM TO trace the history of the development of the Co-operative Committee System in The Consolidated Mining and Smelting Company of Canada, Limited, one must look backward about twenty years. In 1915 and 1916, the first years of the W ar to really affect Canadian life, there were sixteen hundred men working in the Trail plant. These men were, on the whole, a splendid body of men and pa trio tic to the core. They were almost one hundred percent organized, ninety-five percent of them be-longing to the Union of the Western Federation of Miners. Most of the tradesmen belonged to their craft unions as well. For example, there were ? local machinist, steel workers', electrician, boiler maker, bricklayer, and carpenter unions. The Company had always maintained an open-shop policy and refused to enforce membership in any union, but recognized the right of every man to belong to unions. The only exceptions have been the I.W.W. and the One Big Union. Both of these organizations have always been fought by the Company. By 1916, membership in the Western Federation being practically 100 per cent, the Company recognized this organization's authority to make agreements, and a wage and hour agreement was drawn up and signed by the Company and the local officials of the Union, and ratified and signed by the Head Office of the Union in Denver, Colorado. This agreement was for the duration of the war.

Jan 1, 1936

By T. K. Akopyan, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"A qualitative and quantitative analysis of the new Al-Ca-Mn-Fe phase diagram in the region of the aluminium corner is carried out using both thermodynamic calculations and experimental methods. Using the obtained data, the principal possibility of creating both cast and wrought sparingly alloyed aluminium alloys with calcium, manganese, scandium and zirconium at allowable iron contents of up to 0.4% that do not require solution treatment and quenching is justified. At the selected concentrations, the entire amount of manganese (1%) is practically included in the aluminium matrix, while calcium (~2%) and iron are in the multiphase eutectic, which has a fine structure. The joint introduction of 0.25% Zr and 0.1% Sc into the alloy leads to precipitation hardening due to the formation of the L12-Al3(Zr,Sc) phase during annealing. Based on the experimental data for the model multicomponent Al2CaMnFeZrSc alloy, it is shown that such alloys can combine high mechanical properties and good manufacturability during both casting and metal forming. This is due to the combination of a narrow temperature range of solidification with a fine eutectic structure.INTRODUCTION Hardening in branded aluminium alloys (both cast and wrought) is generally achieved by heat treatment of the T6 type, including quenching and artificial aging (Zolotorevskiy, 2007; Kaufman, 2004; Mondolfo, 1976). Heat treatment significantly increases the cost of the final products. Therefore, industrial companies are interested in developing alloys that can be hardened to the desired level without quenching. To solve this problem, alloys with scandium are the most suitable (Toropova, 1998; RØyset, 2005). This element (usually in an amount of ~0.3%) is one of the most effective hardeners in aluminium alloys, due to the formation of Al3Sc (L12) phase secondary precipitates, the size of which is less than 10 nm (Knipling, 2010; Fuller, 2005). These nanoparticles are formed during the annealing via decomposition of the supersaturated aluminium solid solution (hereinafter referred to as (Al)). This feature allows us to significantly increase the strength of aluminium alloys by simple annealing (at ~300°C), i.e., without heat treatment, including quenching. However, scandium is a very expensive metal, so its use as an additive is severely limited. The most effective method is the introduction of scandium together with zirconium (Lefebvre, 2009; Booth-Morrison, 2012). The optimal combination is the introduction of ~0.1% Sc together with 0.20–0.25% Zr, which, according to (Belov, 2006), gives approximately the same strengthening effect as the introduction of 0.3% Sc."

Jan 1, 2018

"RÉSUMÉOn discute les principales sources de dilution au cours d’une exploitation souterraine. Les différentes définitions de la dilution en usage sont analysées. Une nouvelle méthodologie de calcul simplifiée et facile à utiliser dans la pratique minière est présentée. Cette méthodologie permet de remplacer les différentes expressions analytiques en usage par les deux facteurs de dilution seulement : un «facteur de dilution planifiée» lié à la sélectivité d’abattage au niveau de la planification minière et un «facteur de dilution additionnelle » permettant de juger de l’efficacité du contrôle de terrain et de la dilution pendant l’exploitation souterraine. L’application de cette méthodologie donnerait un outil nécessaire aux niveaux de la planification, du suivi des travaux d’exploitation et d’éventuelles études comparatives des coûts entre les différentes situations minières.ABSTRACTThe principal sources of dilution during underground evaluation and mining are discussed, then definitions of ore dilution currently in use are analyzed. These definitions vary depending on the authors. A new ore dilution evaluation methodology is proposed, replacing the ten different analytical expressions by only two: the planned dilution factor related to the stoping selectivity, done at the mine planning level, and the additional dilution factor related to the efficiency of the dilution control measures during stoping operations. The conclusion shows that the use of this methodology would be a definitive asset in planning, in stoping operations follow-up, and in future costs comparison studies between mining operations."

Jan 1, 2001