Search Documents

By E. V. Konopleva, H. J. McQueen

"The isothermal bainite transformation kinetics of low- and medium-carbon alloy steels after hot deformation and the rmocycling treatment (TC) has been studied by the magneto - metric method. Deformation was produced by rolling at 800°C-1000°C. TC included three cycles of rapid (30°C/s) electro-heating up to 900°C-1000°C followed by quenching.Hot deformation retards bainite transformation in the lower part of bainite range (<400°C) and accelerates it in the upper part (>400°C). The effect is greater for higher strain and lower deformation temperature. Deformation also diminishes the overall bainite fraction below 400°C and increases the completeness of reaction above 400°C.Thermocycling provides more uniform ultrafine austenite grains with average size of 3 µm -4 µm compared to 12 µm -14 µm after conventional heating. The transformation rate after TC was almost the same as after conventional heating in low-carbon steel but was faster in medium-carbon with no change in the completeness of reaction. The degree of acceleration increased with rise of transformation temperature.There are a number of factors which are responsible for a change in bainite transformation kinetics in austenite deformed at high temperatures or subjected to TC. One of the most important factors is the refinement of structure, another one is structural and chemical inhomogenity of austenite due to deformation or to rapid heating. To estimate the contribution of these factors, ?-transformation was studied after different austenitizing conditions (low-temperature heating at 850°C- 950°C; high-temperature heating at 1100°C; step treatment – austenitizing at 1100°C, then cooling to 950°C-850°C). The results obtained make it possible to conclude that the structural and chemical inhomogeneity of austenite activate the bainite reaction while the grain refinement retards it. Intensity of the effect produced by each factor depends strongly on the steel composition."

Jan 1, 1997

By T. Orser

In 2010 Newmont made the decision to purchase a 42 foot (ft) Semi-Autogenous Grinding (SAG) mill from Metso and a 28 Mega-Watt (MW) Gearless Mill Drive (GMD) from ABB for the Conga Project in Peru. The test and study work showed that a single line 42 ft SAG mill circuit gave the most favorable project economics in comparison to an equivalently powered single line 40 ft SAG mill circuit. This paper does not address the process design or the project economics, but instead focuses on the key aspects of the SAG mill design, GMD design and the associated component manufacturing. This paper also addresses, where applicable, the potential reliability differences between the initially proposed 40 ft SAG mill and the finally accepted 42 ft SAG mill.

Jan 1, 2012

By J. W. Meier, J. O. Edwards, R. C. Bell

"IntroductionTHE DIE CASTING industry .as we know it today is the direct result of the invention and development of die casting machines during the nineteenth century and of reliable alloys in the twentieth. The early machines were designed to cast low melting point metals such as lead .and tin, and their alloys.It was inevitable that, as these die castings were put into service, the demand should arise for stronger materials. Zinc alloys, often containing lead, tin, copper, and aluminum as major constituents, were relatively easy to cast and stronger than the lead and tin alloys. However, it became apparent after a number of years that these zinc alloys tended to become brittle, distort, and corrode, particularly if kept in warm, humid atmospheres. Thus, considerable quantities of zinc-base .alloys were in use before the trouble was realized and effective measures could .be taken to determine the cause of the instability.The deleterious effect of certain metallic impurities on the properties of zinc •die casting .alloys has now been known for about thirty years. Brauer .and Peirce, and, later, other research workers of the New Jersey Zinc Company such as Anderson and Werley, discovered the pronouned effect of lead, cadmium, and tin on the stability of zinc-alloys."

Jan 1, 1952

By P. J. Lunder, R. C. Pakalnis

This paper presents the results of research that has been undertaken in order to develop an improved method of determining the strength of hard-rock mine pillars. Pillars are found in various shapes and sizes in all underground mining operations. Prudent engineering design requires that if pillars are to perform as desired, both the pillar strength and the pillar stress must be determined. A detailed pillar stability study has been combined with an extensive database of published pillar case histories (178)resulting in a new “hybrid” pillar strength formula, “The Confinement Formula”, that utilizes classic strength of rock methods combined with empirical methods. “The Confinement Formula” utilizes a “mine pillar friction term” calculated from the average minor/major stress ratio with-in the pillar core. Statistically, the new formula provides better results at predicting pillar strength for the combined database than the best empirically ft pillar methods that currently exist. “The Confinement Formula” allows for the determination of the strength of mine pillars with an increased level of confidence over previously applied methods.

Jan 1, 1997

By H. Memarian

In the last few decades, many developing countries have tried to expand and improve upon higher education, which is acknowledged to be the leading factor for development. In this respect, develiping countries have significantly increased the number of tertiary institutions and their students. These rapid expansions, along with all the benefits, have drawbacks as well. An example is the status of mining engineering education in Iran. Presently, the number of active mining engineering departments in Iran (27) is more than the sum of similar departments in Canada, Australia, the United Kingdom, and South Africa (23 altogether). Also, the number of annual mining graduates in Iran (645) is more than the cumulative graduates of the United States, Canada, the United Kingdom, and Australia (613). The expansion of mining engineering education in Iran has coincided with the closing or merging of similar mining departments, as well as a decline in the number of interested students in the industrialized world. The present study shows that the need for development and the excessive number of high school graduates, resulting from high population growth in the early 1980s, are the two primary factors influencing the significant expansion of mining engineering education in Iran.

Jan 1, 2007

By R. Bainbridge

THE cinnabar deposits of the Consolidated Mining and Smelting Company&apos;s Pinchi Lake property, situated near Fort St. James, B.C., were discovered and reported on by a Dominion Government geological party in 1937. Claims were staked by a group of local prospectors and, later, the Consolidated Mining and Smelting Company of Canada, Limited, took an option on the property. By the fall of 1939, exploration work had indicated ore of commercial quantity and grade, and laboratory tests had shown that standard methods of reduction, namely, roasting of the ore, followed by condensation of the mercury vapour produced, would result in satisfactory recovery. In June, 1940, construction of a 50-ton unit arranged for wood firing was completed and operation commenced. The installation consisted of a 46 in. by 60 ft. rotary kiln (see Figure 1) followed by a 14-in. Sirocco cyclone, a cast-iron condenser unit, and a 1,700 c.f.m. fan, exhausting to a stack. Other equipment included a 9 in. by 18 in. Denver jaw crusher with the necessary bins and feeders. As the need for mercury was urgent, because of war requirements, construction of a duplicate unit was begun almost immediately. This first extension started operation in January, 1941, and the plant was then capable of treating about 150 tons of ore daily.

Jan 1, 1945

By John Galbraith, Dwayne D. Tannant, Chris C. Langille

"Development of underground openings in a deep mining environment requires a support system that is able to absorb energy as a result of dynamic loading due to rockbursting and blasting and static loading due to convergence as the development face advances. The support system must be resistant to corrosion and be effective over the life of the excavation, upward of ten years, yet simple and cost effective to install. Over the past two years, research has been conducted at INCO’s Creighton Mine to try and identify a one-pass grouted support system that will meet these needs.The main problem faced, with simply using grouted rebar at depth, is the effect of tunnel convergence on the stiff grouted bolts. Typically, if fully grouted, stiff rebar are installed to the face of an advancing development heading, the amount of convergence that occurs can result in failure of the bolts at the face plates used to attach the mine screen to the back. An initial support is required to enable crews to continue the bolting cycle in the immediate term, yet allow for this convergence over the longer term as the drift advances. The ideal support system will allow both to occur, giving effective immediate support while providing long-term effectiveness in allowing convergence to occur while maintaining the capacity of the bolt.This paper will investigate the expected convergence in deep development headings at +2200 m (+7200 ft) through the use of direct measurements using both flex rod extensometers grouted into the back of a development heading and five-point tape extensometer stations. Measured results will be compared with simple2-D numerical analysis to evaluate the anticipated convergence expected to be absorbed by the bolting system. The required convergence will then be compared with load deformation response of several support configurations."

Jan 1, 1996

By Claude Hubert, Alex C. Brown, Pascal Marquis, D. M. Rigg

"Numerous studies of the Bousquet mining district, Abitibi, Quebec, mainly following the successive discoveries of new gold deposits over the past two decades, have led to a broad range of genetic hypotheses for their gold deposition. A compilation of petrographic, structural, and geochemical data indicates that the gold deposits are composed chiefly of pyritic schists derived from felsic and mafic volcanic and volcaniclastic protoliths, and of auriferous massive pyrite hosted by pyritic schists of felsic affinity. The deposits are typically located within zones of local pyrite enrichment and advanced-argillic alteration which are in turn enclosed within much larger zones of disseminated pyrite included in regional-scale, commonly anastomosing, zones of sericitic alteration.Overprinting relationships between three sets of folds and foliations indicate that the host-rocks of the gold deposits have retained the imprint of three successive generations of ductile deformation resulting from regional dynamothermal metamorphism. Sericitic and advanced-argillic alteration, together with massive sulphide deposition, are interpreted to have taken place prior to the onset of the ductile deformation, based on observations 1) of altered fragments of wallrocks which are enclosed within massive sulphide bodies and were thus preserved through regional metamorphism, 2) of the syntectonic deformed pyrite, and3) of the syn-tectonic porphyroblasts of andalusite, garnet and plagioclase. The orebodies are oblate to prolate, and the pyrite-gold mineralization is typically vein-type, distributed in foliation-oblique and foliation-parallel veins. The gold-bearing structures postdate all foliations, and are associated with retrograde alteration assemblages that are pseudomorphic after pea~-metamorphic porphyroblasts in host-rocks, and with cataclasticfabrics that overprint syn-metamorphic pressure-solution features and annealing fabrics in pyrite.Retrograde gold-bearing assemblages indicate a chemical disequilibrium between the ore-forming fluids and their host rocks. This disequilibrium rules out the possibility that gold was remobilized from its own host, and suggests, instead, that the ore-forming fluids and their metal contents had an allochtonous source. Stable and radiogenic isotope analyses indicate that the fluids had a metamorphic origin, and that the associated alteration took place after the culmination of the Kenoran orogeny."

Jan 1, 1990

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By O. G. Olvera

"Refractory sulfidic ores consist of materials in which gold occurs finely disseminated within metallic sulfides or forming solid solutions, with pyrite and arsenopyrite being the two sulfides most commonly associated with gold. Typical cyanide operations show poor performance and require oxidative pretreatments to increase gold recovery. Pretreatment alternatives include roasting, pre-aeration, acidic and alkaline high pressure oxidation, and bacterial oxidation. The presence of arsenic, however, introduces a serious disadvantage to the use of roasting and bacterial leaching, while high pressure oxidation involves high capital costs. This work focuses on evaluating the effect of the addition of a carbon resin as a sulfur collector on the oxidation of different arsenopyrite concentrates under atmospheric tank leaching (ATL) conditions. The addition of the resin improved the oxidation of sulfides and favored the formation of elemental sulfur over the generation of sulfate. The use of AF5 in ATL resulted in higher gold recoveries under standard cyanide carbon-in-leach and thiosulfate leaching.INTRODUCTION Refractory sulfidic ores consist of materials in which gold occurs finely disseminated within metallic sulfides or forming solid solutions, with pyrite and arsenopyrite being the two sulfides most commonly associated with gold. Gold is not readily accessible to solutions in these types of ores and typical cyanide operations show poor performance, thus making the use of oxidative pretreatments a requirement to increase gold recovery. Pretreatment alternatives include roasting, pre-aeration, acidic and alkaline high pressure oxidation, and bacterial oxidation. The presence of arsenic, however, introduces a serious disadvantage to the use of roasting and bacterial leaching, while high pressure oxidation involves high capital costs. The use of carbonaceous materials to enhance the dissolution of sulfides is not novel, and leaching additives such as coal, activated carbon and carbon powder have been considered for the improvement of bioleaching, atmospheric leaching, and pressure oxidation leaching processes. However, this type of technology has been focused mainly on the recovery of copper from copper concentrates containing chalcopyrite with less attention paid to other sulfides."

Jan 1, 2017

By W. A. Lang

Introduction In this review, which is the fifth of the series on the Progress in Coal Technology, an attempt has been made to outline some of the more important developments that have taken place in coal carbonization during the last decade. Research into both high-and low-temperature carbonization has been active for three principal reasons: (1) the growing shortages in most countries of high-quality coking coals; (2) the demand for smokeless fuels for domestic purposes; (3) the need for metallurgical coke for the increased output of steel in the post-war years. The growing importance of coal tars as a source of chemicals for the preparation of synthetic products and of coal gases for the recovery of sulphur is evident. Many of the researches initiated because of wartime necessity have been continued .and even expanded in the post-war years. High-temperature carbonization with a suitable coal yields a strong coke which is used primarily for metallurgical purposes, a tar with good marketable value, and a large yield of gas of medium calorific value. Low-temperature carbonization gives a more free-burning solid product suitable for a domestic fuel, a high yield of a tar which is generally regarded as superior to high-temperature tar for chemical purposes, and a smaller yield of a higher-heat-value gas.

Jan 1, 1951

By W. A. Lang

COAL of sub-bituminous rank underlies much of the plains area of Alberta. This coal is geo-logically young, and occurs in Belly River and Edmonton strata of Up-per Cretaceous age. Generally, the seams are flat-lying, but in some areas they may dip as much as 5 degrees. The overburden, composed mainly of glacial clays and sand-stones, may vary in depth from a few feet to several thousand feet. Recovery of the coal has &apos;been by drift, slope, and shaft underground mines, and by open-pit stripping operations. Production has been obtained from a large number of mines, most of which have been relatively small and with preparation equipment limited to a loading tipple with screening facilities, and a picking belt where high-ash materials can be removed from the larger sizes. The coal has been sold for domestic and industrial space-heating, for production of process steam, and for power generation. In re-cent years competition from natural gas, propane, and oil has seriously interfered with the production and marketing of sub-bituminous coal, especially with the disposal of the smaller sizes at a realistic price.

Jan 1, 1958

By Damien Gaboury

"Two practical methods for correlating two or more diamond-drill core intersections, using a stereographic projection software are presented. The first may be used to establish if two or more vein intersections are correlative, based on their core angles and diamond-drillhole attitudes. The second method allows prediction of main vein attitudes from numerous intersections, based on a spherical density contouring projection. The methods are suitable for: (1) correlating veins in complex orebodies; (2) ascertaining lateral continuity of ore for reserve estimations; (3) demonstrating the hidden complexity of an orebody; and (4) correlating and interpreting various planar elements.IntroductionModern mineral exploration relies on diamond- drill core data and on the ability of geologists to interpret them. Drill core generally yields unoriented information, unless an expensive orientation device is used. As a consequence, strike and dip of planar elements such as lithological contacts or mineralized veins cannot be determined easily. This is particularly true for blind deposits (covered by thick overburden) and complex orebodies, where field data cannot support drilling interpretations. Such a problem has been addressed previously using two and three diamond drillholes and several solutions were proposed based on trigonometry, and geometric and stereographic projections (Mead, 1921; Wisser, 1932; Fischer, 1941; Stein, 1941; Bucher, 1943; Gilluly, 1944; Addie, 1962; Mills, 1963; Lyons, 1964). However, these solutions are time consuming and not relevant to present day computerized data plots."

Jan 1, 1997

By A. Desbiens, A. Pomerleau

During the summer of 1994, a new PID-based control strategy was installed on line B of the grinding circuit at the Kidd Creek Division of Falconbridge Ltd. Part I of this paper described the methodology used to select the appropriate control strategy using a phenomenological dynamic simulator. Part II presents the implementation of the control strategy. Prior to the controller installation, it was necessary to solve various problems related to the process, such as a cyclic behaviour of the rod mill feed tonnage, a problem related to the mill water source and the calibration of the flowmeters. Once these problems were solved, the control strategy was accomplished in two steps. Step 1 corresponds to the installation of control loops to regulate the pump box level and the cyclone overflow density. Step 2 describes the implementation of a loop to control the cyclone feed density. According to Part I, a loop to control the circulating load is also part of the original design. However, reasons are given to explain the rejection of this loop. For both steps, technical procedures such as filtering, process identification and controller tuning are detailed. Finally, the operator’s interface is briefly described.

Jan 1, 1997

By P. A. Distin, Jr. da Silva

The history of commercial processes for zirconium/hafnium production and separation is reviewed. A new technology is then proposed as a potential alternative for zirconium/ hafnium separation in a simpler, cleaner way than achieved with current processes. Primary sources of zirconium always contain small amounts of hafnium that must be removed during production of zirconium metal for nuclear applications. This separation is usually carried out by a solvent extraction process, developed in the 1950s, that selectively extracts hafnium, as a thiocyanate complex, using methyl isobutyl ketone (MIBK). Environmental problems inherent to this process are the high aqueous solubility and low flash point of MIBK, and possible gaseous contaminants formation generated by the decomposition of the thiocyanic complexes in hydrochloric acid medium (H2S, HCN, mercaptan’s formation). The present work shows how these problems could be avoided by using organophosphorous extractants that were unavailable when the MIBK process was developed.

Jan 1, 1998

By C. Stamberg, W. McGuire, R. C. Carlson, L. W. Vollmer

"The selection of materials and pre-cautionary measures for handling natural gas and condensate containing aqueous hydrogen sulphide are presented. Based on the results of a pilot production test and laboratory studies, together with several years . of operating experience, it was found that the behaviour of materials in sour gas environments can be predicted sufficiently accurately for engineering purposes.The selection of proper materials is essential for preventing sulphide-stress cracking. Where high strength materials are not required, low car-bon steel is used. Components requiring high tensile strength and hardness characteristics should be made from K-monel or properly heat-treated carbon-manganese-molybden-um and AISI 4140 steels. Welded connections are a potential source of sulphide-stress cracking. Consequently high quality welding and strict inspection are suggested as the most economical precautionary measures available.A maintenance program based,. where possible, on visual inspection of equipment and/or test spools located at strategic points should be used to follow weight loss and putting corrosion in sour gas environments. If severe weight loss or pitting corrosion is encountered, inhibitors have been found to be an effective deter-rent."

Jan 1, 1960

By A. Flemming

"As the next century draws near, new mine properties must be brought into production to replace existing operations that are approaching their economic life. This paper presents some of the critical technical issues being addressed by Manalta Coal Ltd. as they strive to bring the Telkwa Coal Project near Smithers, BC into production during the year 2000. The mine is planned to produce between 1.0 to 1.5 million tonnes per year of medium volatile coal for export to overseas thermal and PCI markets. IntroductionManalta Coal Ltd. (Manalta) is proposing the development and operation of a surface coal mine and associated infrastructure approximately six kilometres southwest of the village of Telkwa, British Columbia (Fig. 1). The infrastructure consists of a coal washing facility, tailings disposal area, clean coal haul road, access road and rail loadout facility. Over a 25-year period, the mine is expected to produce between 25 and 37 million clean tonnes of coal primarily for the export market.To achieve public and governmental approval for the development, the project will be reviewed under British Columbia’s Environmental Assessment Act. Manalta entered the formal Assessment process in February 1, 1997 with the submission of an Application for a Project Approval Certificate for the Telkwa Coal Project."

Jan 1, 1997

By F. W. Gray

A GEOLOGICAL study seeking to determine, for economic purposes, the value of the Sydney coalfield as a source of coal supply. Limitations of the coalfield come under two main heads: (a) Areal extent of the undersea coalfield. (b) The distance from shore at which coal can be mined at a cost of production permitting its profitable sale. Conclusions reached are that the areal extent of seams below the Phalen seam is of. small economic importance, and that non-persistence of these seams in full thickness and quality in the undersea extension of the coalfield will put an end to profitable mining before any limitations connected with distance from the shore-line become operative. With respect to the Phalen seam, non-persistence or deterioration of the seam will become effective in the western part of the coalfield, and less certainly in the eastern part of the coalfield, before operation of limitations by distance from shore. In the central portion of the coalfield, the seam probably persists in commercially workable thickness and quality to beyond the limit of mining set by distance from the shore-line. With respect to the seams above the Phalen seam between the Mountain fault on the extreme western boundary of the coalfield and the assumed termination of the deposition area on the eastern extremity of the field near South Head of Morien, there appear to be only such limitations as arise from engineering approach, distance from shore, sufficiency of strata cover between the sea-floor and the upper coal seams, and quality of the coal (with certain reservations as to the continuity of the upper seams under Sydney harbour and in the Sydney Mines-Little Bras d&apos;Or district). Some of these seams have fragmentary land outcroppings from which their persistence seaward is assumed, and there may be other and still higher seams in the strata column which are entirely submarine.

Jan 1, 1941

By O. Peters, D. Lascelles, R. Caldwell

Ageing tests on a crushed Cu-porphyry ore were conducted to assess the impact of sample oxidation on flotation performance. The objective of the testwork was to simulate ageing of ore that would be blasted through block caving but not milled for possibly several months. Ageing was performed in specially designed columns, using site and deionised water to keep the samples moist over the entire ageing period. Samples from each ageing interval (0, 0.5, 1, 2, 4, and 8 months) were examined for physical and metallurgical changes resulting from the ageing process through chemical analyses, size analyses, and batch flotation tests.

Jan 1, 2009

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998