Search Documents

By A R. Gerson

Pyrite, chalcopyrite and mixed sulfide samples, with and without quartz (5 wt per cent S), were subjected to column leaching to mimic natural weathering (cyclic wetting and drying). The pH and SO4 2- concentration of the column effluent was measured over a period of 78 weeks. The pH of the pyrite-only containing column rapidly decreased and remained under pH 4 after 12 weeks of leaching. The pH calculated assuming a 2:1 ratio of H + generation and SO4 2- release was slightly lower than that measured. However, a reduced H + to SO4 2- ratio of 1:1 is predicted if the release of aqueous Fe 2+ is assumed rather than the formation of Fe(OH)3. The pH of all columns containing only chalcopyrite or a 1:1 mole ratio of chalcopyrite and pyrite remained at or above pH 5 for the duration of the leach even though significant SO4 2- was released. One column containing the same initial surface area of pyrite and chalcopyrite but only approximately 0.10 the mole fraction of S as chalcopyrite maintained a pH of greater than five for the first 56 weeks of leaching and showed sporadic acid production thereafter. It is well established that oxidation of chalcopyrite results in a surface layer of polysulfide material. It is the formation of polysulfide that neutralises the acid produced on S oxidation through to SO4 2-. Hence where polysulfide formation occurs extensively on chalcopyrite the resulting solution pH decrease will be less than that based on SO4 2- production. The oxidation rate of sulfide minerals increases with decreasing pH and hence acid formation via sulfide oxidation to SO4 2- causes the subsequent oxidation rate to increase. The addition of calcite (CaCO3)to a pyrite column not only neutralises the acid formed but also decreases the rate of release of sulfate to solution by a factor of approximately 30. This is also the case where chalcopyrite is present mixed with pyrite. The rate of release of sulfate from the mixed sulfide mineral columns (after the initial release of the sulfate already present) was between one-fifth and one-tenth that in the absence of chalcopyrite.

Jan 1, 2003

By A M. Robertson, R Lefebvre

Air movement and associated oxygen transport through waste rock dumps has the potential to significantly enhance the rate of oxidation of pyrite-bearing material. While this is a desired outcome for most heap leach operations, airflow in waste rock storage facilities can result in significant increases in generation and acceleration of acid rock drainage. Hence, a good understanding of internal airflow through waste rock dumps is required to control ARD and minimise any associated liability. The principal mechanisms contributing to airflow and oxygen transport in a waste rock pile include: diffusion; advection due to a thermal gradient (chimney effect) and/or wind pressure gradients; and advection due to barometric pumping. While diffusion is typically limited to a near-surface zone of a few meters depth, advection and barometric pumping have the potential to move air (and oxygen) to much greater depths into the pile. In general, the more permeable the waste rock material, and the greater the height-to-width ratio of the waste rock pile, the greater is the potential for advective air movement. The reactivity of the waste rock material as well as the coarseness (hence air permeability), and the spatial variability of these properties within a pile, have a strong influence on the magnitude of thermally induced advection. In contrast, air movement due to barometric pumping is controlled by the waste rock porosity, changes in ambient air pressure and the heterogeneity of air permeability of the waste rock dump. Results of field monitoring and numerical modelling using TOUGH AMD are presented to illustrate the concepts on air movement in waste rock piles discussed in this paper. During the design and construction phase, airflow can be controlled by judicious placement of reactive waste rock and use of selective placement techniques to control the internal structure of the waste rock facility (eg introduction of horizontal layering, prevention of inclined, high-permeability, channels (æchimneysÆ)). Several closure measures are available to minimise airflow including: placement of a low-permeability cover to reduce air entry; and placement of a non-reactive cover material to isolate reactive material from the zone of active airflow and/or regrading of the waste rock pile to obtain a geometry and internal structure less susceptible to advective airflow.

Jan 1, 2003

Using normal low pressure filtration methods for the dewatering of fine china clays, the best that can be achieved is cakes with about 30% moisture. In order to get the moisture levels down to acceptable levels the traditional method used is thermal drying, which is both costly and dust creating. It was to improve this process that ECC International embarked upon a programme of development of filtration equipment using high pressure to achieve significantly lower moisture levels. This development work investigated several design philosophies and culminated in the production of two quite different solutions. The High Pressure Plate Press uses round plates / chambers of one metre diameter and a filtration pressure of 70 bar. This press is fully automatic and produces a surface dry cake that has sufficient plasticity for the further processing that is required on specific qualities of china clay. The TUBE PRESS on the other hand uses a unique design configuration and operates at a filtration pressure of 100 or 140 bar, depending upon the model. The TUBE PRESS produces a brittle, surface dry cake that is easy to handle and a filtrate that is usually crystal clear. The TUBE PRESS achieves a much higher degree of separation than is possible with conventional equipment, which is particularly important if the filtrate is the product. Over the past 15 years plants incorporating both HP Plate Presses and TUBE PRESSES have been installed in the china clay operations of ECC International and are giving excellent trouble free service. The TUBE PRESS has also proved to be extremely versatile, effectively dewatering a wide range of fine particled slurries, in a number of diverse industries.

Jan 1, 1989

The geotechnical and environmental aspects of heap leaching are very closely tied during design, operations and closure. Potential environmental impacts from heap leaching are mostly due to land disturbance and water quality issues, including both groundwater and surface water. Water quality issues are mostly related to containment design, which is primarily a function of proper sizing of the facilities and site specific liner design. Geotechnical analyses is the dominant discipline in providing cost efficient, operationally effective and environmentally sound heap leach facility designs. Much has been published on geotechnical aspects of heap leach design, for example Van Zyl, Hutchison and Kiel (1988) and Van Zyl (1987). This paper will emphasize a few specific aspects related to the geotechnical and environmental consideration for heap leach projects. These aspects are: ò site investigation; ò containment design; ò slope stability; ò heap flow dynamics; and ò closure design. Design of a heap leach project must consider not only the operating life but also closure and post-closure considerations. As a matter of standard practice, designing for closure is an extremely important concept. Not only is it important for environmental aspects, but experience also shows that projects designed for closure will be overall more economical for the total life cycle of the project. Closure considerations are also important during project feasibility evaluations to ensure that total life cycle costs are evaluated.

Jan 1, 1994

By White B

A novel approach is suggested for the solution of planning and development problems in the coal, mining industry. The formation of coal measures depends to a significant extent on sequential geological processes and events which are probably best defined in a "system of processes and responses." The great number of variables in such a system is a characteristic feature of geological environments. Research work over the past two decades, in particular, has successfully established analytical procedures for the identification and definition of relevant and irrelevant variables for mining developments in specific geological situations. Such situations are typifiable within the regional geological setting of coal deposits. Scale gaps can be bridged by reliance on common symmetrical attributes and pervasive geometric features. Depositional processes and their resulting attributes are responsible for the development of mechanically significant rockmass "defects" and anisotropies; such features have to be identified and assessed for the selection of colliery design criteria. It is suggested that the procedural frame- work of systems engineering analysis is a most appropriate tool for the assessment of those geological features that can influence the mechanical behaviour of the "floor-seam-roof" system in "high technology" mining operations of the future. It is anticipated that the overall emphasis of future mining systems will be toward the use of larger scale more highly productive methods and machines, with higher capital outlay but

Jan 1, 1987

Metal grades and contents of ore deposits should be measured in an unbiased manner, and with a degree of precision that reduces to an acceptable level the risk to put into production inviable prospects. The additive property of variances for metal grades and contents is used to assess the accuracy and precision characteristics of this measurement process. Each stage in the process of extracting different types of samples from ore deposits, preparing test samples from drill core sections, drill chips or crushed ore, and collecting and assaying test portions, contributes a variance component to the intrinsic variability of a metal's distribution in its matrix. Deducting such extrinsic variances results in more precise estimates for metal grades and contents of elementary units. The cumulative metal content for a set of elementary units of in-situ ore, and the sum of the variances for metal contents of all units in the set, can be used to calculate confidence intervals and confidence ranges at different probability levels as measures for risk.

Jan 1, 1976

By T

THE Sulphide Corporation's works for the smelting of ores containing lead, gold, and silver are situated close to the Cockle Creek railway station, on the main Northern railway line, and are about 95 miles from Sydney and 10 miles from Newcastle. A branch line runs to the works, and siding accommodation and bins are provided for expeditiously handling all ores sent for treatment. The Corporation also possesses wharfage facilities at the port of Newcastle, where consignments of ores arriving by sea can be handled direct into railway trucks for conveyance to the works.The greater portion of the ore treated at Cockle Creek comes from the Corporation's mine at Broken Hill, but a large quantity of other grades is also purchased and treated.

Jan 1, 1918

According to the Australian Bureau of Statistics, fatalities from road transport accidents represented an average of over 97 per cent of all transport related accidents between 1997 and 2002. With increasing traffic density, tunnels are becoming a more viable means of providing alternative travel routes to ease areas of congestion in the road transport network. However, unlike open road conditions, a fire incident in the confined space of a tunnel environment may impact upon many users that are remote from the incident location. In this context, designing for an appropriate level of safety in tunnels is therefore an important consideration for achieving consistency in the life safety measures for users of the road transport network. Unfortunately, like fire safety engineering design for buildings, there are presently no clear measures in the design processes to assess the adequacy of the design in terms of attaining the level of safety implicated in the design objectives. This is partly due to the indeterminate nature in which the design objective or the level of performance measure is stated û the intent of the objective is relatively clear but the measure of it is not. Another reason is the lack of a standardised procedure for determining the critical design variables affecting life safety. This is important to ascertain consistency in the use or adoption of the important parameters for design. This paper looks at the processes involved in the fire engineering design of road tunnels that are currently practised. A review of the design processes for fire safety in road tunnels is provided, which includes the range of fire scenarios in a tunnel environment, the traffic flow and composition, the relevant fire protection systems, the ventilation and smoke control system, the egress provisions and the benefits of incorporating fire brigade intervention. A simplified risk assessment approach is developed for a typical road tunnel to assess and evaluate the impact of a range of design parameters on life safety. Using a sensitivity technique, the important variables are then identified and means of reducing design variations associated with them are recommended. The technique may be further refined for use in the development of codes or guidelines in order to develop a suitable means of deriving more consistent design values, and hence achieve better consistency in the overall level of safety in the design.

Jan 1, 2008

Launching the Queensland Water Plan 2005 - 2010 in August 2005, Premier Peter Beattie compared the stateÆs water resources with liquid gold. QueenslandÆs peak industry body for the minerals and energy sector, the Queensland Resources Council (QRC), believes the analogy is appropriate. During early development of an industry water strategy, it has become apparent that water is like liquid gold, in that it is revered, hoarded, recycled, priced on purity, a magnet for speculators, both difficult and expensive to transport effectively, heavily regulated and fundamentally linked to issues of security. To date it has generally been economic and relatively straightforward for the resources sector to secure water. Although production has not been compromised, this must not be grounds for complacency as there is every indication that water will continue to become increasingly expensive, more tightly regulated and, relative to a growing demand for a finite water supply, increasingly scarce. During 2006, QRC has developed and is implementing a voluntary industry water strategy to address a range of challenges confronting the resource sectorÆs security of access to water. As a consequence of, at times, protracted community consultations over QueenslandÆs catchment-based water planning processes it has become clear that many community stakeholders have outdated perceptions of the stateÆs resources sector. Once established, QRCÆs water strategy will incorporate a community engagement campaign to present the industryÆs credentials as a leader in water resource management. The development of QRCÆs water strategy, and the challenges the strategy is designed to address, provides insight into the fundamental reforms that are occurring in how water is managed and regulated in Queensland. These reforms have implications for how government policies are designed and administered and also for how industry engages with communities during this transition process.

Jan 1, 2006

Current NSW Government policy requires searching for more than just minerals during an exploration program - add endangered fauna and archaeological relics for a start.

Jan 1, 1995

By N C. White, L Danyushevsky, D R. Cooke

Comb-layered textures preserve the cyclic accumulation and release of volatiles inside magmas that are temporally associated with large Cu-Au-Mo-rich porphyry ore deposits. Fluid inclusions in these textures sample pristine magmatic fluid. Microanalysis of this fluid helps constrain the physical models that operate at melt-fluid interface and in the broader magma system responsible for ore deposit formation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Bhattacharyya A. K

In this paper, the current methods for predicting surface subsidence due to underground coal mining are evaluated first. A single index, called a strata parameter (P), is then proposed to describe the overall character of the undermined strata in the context of surface subsidence. Based on the strata parameter, a method for predicting the maximum surface subsidence for various panel width (w)/depth (h) ratios is presented, which has been tested against specific empirical curves or data from several coalfields in different countries. From the data relating to several coalfields, a linear relationship between the reported average angle of draw and the strata parameter has been established. It has also been found that the strata parameter can be used for studying the locations of the inflection points and the shapes of transverse subsidence profiles.

Jan 1, 1995

Interrelated data for five fundamental features of production processes would help promote the- development of the discipline and profession of extractive metallurgy. The features are the input materials, the products, equilibria, kinetics" and movement of materials within the reactor. Aspects of overall process performance that could be developed in these terms include quantitative comparison of reactor engineering options, process dynamics, interruptions to operations, and recycling. The ability to be able to forecast these and other aspects of process performance would be valued by most metallurgists. Although data have been reported for each of these aspects they have been more relevant to process economics than process fundamentals. The data have not often been interrelated via the fundamental features for a particular raw material-process system; nor have ~ similar data been related for different systems.

Jan 1, 1986

By Belcher C. B

A simple gravimetric procedure was developed for the rapid determination of carbon dioxide in coal mine roadway dust samples and the result is used for the subsequent calculation of incombustible matter contentaccording to the requirements of the Queensland Coal Mining Act. The carbon dioxide is determined through loss of mass by a semi-enclosed apparatus, following room-temper.ature hydrochloric acid attack on the sample.With a sample containing 36 per cent carbon dioxide, the achieved standard deviation (ls) of 0·3 per cent CO. is adequate for coal mine roadway dust analysis.This simple procedure enables relatively unskilled labour in mine laboratories, to analyze coal mine roadway dust samples in accordance with the Act. Some 50 analyses can be achieved per day compared with 8 by the Australian Standard Method for coal.

Jan 1, 1976

Of the energy resources present in Australia, coal and uranium are by far the largest. These two resources ap- pear sufficient to satisfy Australia's energy needs beyond the immediately foreseeable future and long after the natural petroleum resources are exhausted or have ceased to play a significant role. By that time, coal could be converted in plants of very large size to synthetic liquid and gaseous fuels which will be used as substitutes for pet- roleum fuels, particularly for transport. The basic role of uranium will be to supply electricity from nuclear power stations for heat and power requirements, thereby freeing non-coking coal largely for conversion purposes. The establishment of these enterprises will require a massive national effort and a high degree of co-ordination at the planning stage.

Jan 1, 1975

A wide variety of process streams are sampled for grade control in the mining industry. However, in many instances the overall precision of the resultant analyses is inadequate for the intended purpose, ie grade control and optimisation of resource utilisation. Consequently, special attention needs to be given to the sampling, sample preparation and analysis procedures in place to ensure that meaningful grade control decisions can be made based on the analyses generated. For example, it is virtually impossible to control a process to within, say, ¦0.2 per cent if the overall precision of the analyses is no better than 0.5 per cent. Hence, precision targets appropriate for the task need to be established and the overall precision achieved in practice monitored and controlled on an ongoing basis.

Jan 1, 2008

By P Andersson, P Marklund

Evaluation of different techniques for bottom fill stabilisation showed that frozen fill was the most economical method. In order to test the method a full-scale field test was performed in the Rehnstr÷m mine. The test was instrumented with temperature gauges and extensometers. Before the field test, frozen fill was tested at the laboratory. The mechanical properties of the frozen fill were determined by uniaxial compression and creep tests. A deformation model for the frozen fill was set up. Calculation procedure for design of spacing between the freezing tubes, time for freezing and calculation of the necessary capacity of the refrigeration plant was developed. These procedures were calibrated against the field test. The results of these investigations allow the following conclusions: From a mechanical point of view, frozen fill has excellent properties as a structural member and it also has excellent properties to support itself and the fill above. Methods for the thermal and mechanical design of freeze stabilisation have been developed and found adequate. The need to place the freezing tubes several years in advance of the future sill pillar mining, requires careful long-term planning and accurate documentation.

Jan 1, 1998

By Netchaef P

A rationale is presented for the use of vegetation on mine dumps to minimise runoff and infiltration which become vehicles for potential pollution. The unique topography of mine dumps promotes high atmospheric advection which leads to extraordinary energy levels for evaporation discharge - the driving force of vegetation "pumps". This effectiveness is mainly a function of how well the vegetation will grow on a given site. Recent advances in technology allow water discharge by vegetation to be measured semi-automatically, accurately and cost effectively. As a result the basis now exists for a thorough evaluation of the optimum mine dump vegetation cover. This paper presents the current status of dump rehabilitation as seen by the mining industry. The significant prospects for use of vegetation to minimise mine water related problems with subsequent savings in capital and operational cost are also outlined. However, to examine the crucial questions of optimum hydrological ability, suitability and cost effectiveness of various types of dump vegetation a proposition is made to interested parties in the mining industry: The CSIRO needs potential study sites to evaluate the hydrological ability of vegetation under mine dump conditions.

Jan 1, 1988

By Gurgenci H, Slifirski M

The Centre for Mining Technology and Equipment was established in 1991 to develop innovative technologies for the mining and processing industries, to introduce these technologies to the industry, and where appropriate, to co-operate with equipment manufacturers to transform these technologies into equipment products. It is an unincorporated joint venture between the University of Queensland, CSIRO and the Australian Minerals Industries Research Association. Base funding for the CMTE is provided by the Federal Government as a Co-operative Research Centre.

Jan 1, 1993

The development of metallurgical training is briefly reviewed. The reasons for the current trend for Metallurgy Schools to become Schools of Materials Engineering or Materials Science are mentioned as is the role of Departments of Chemical Engineering in the teaching of extraction metallurgy. Some problems on academic staff recruit- ment are highlighted and predictions concerning future difficulties in industry getting adequately trained professional staff are made. The need for a special effort to attract and retain the best undergraduate students is put Forward.

Jan 1, 1987