Search Documents

The flotation circuit handling Peko ore at Peko Mines N.L. was examined in July 1970 with a view to determining simple changes in circuitry or reagents which could improve the grade and recovery of the final copper concentrates. The investigation included sampling over one shift followed by detailed testing of the samples by sizing-assays, sizing-mineralogy and sizing-liberation. Mass balances were carried out over total streams, the component minerals and the copper contents. Some laboratory work was carried out to assess the effect of salinity on flotation. In order to handle the sizing-mineralogy calculations a computer programme was set up. The raw data were corrected for locking factors, then mineral and elemental distributions cal- culated for each screen fraction and the total sample. Calculated assays from grain counting were compared with chemical assays. Recoveries through the size-ranges re- vealed very rapid flotation of copper minerals at sizes below 350 mesh. This pointed to a possible circuit improvement by desliming rougher tailings ahead of the scavenger stage. A strong correlation was found between water in concentrates and gangue recovery for the subsieve sizes. This pointed to clean water additions to the cleaner circuit as a way to 1 Project Consultant, The Australian Mineral Development Laboratories, Adelaide, South Australia.

Jan 1, 1972

The value of water is defined by its marginal utility. Challenges arise where the marginal utility is difficult to estimate. Therefore, when two or more interested parties wish to access water and they cannot use commensurate units for marginal utility; other means of value comparison must be sought. It is asserted here that sustainability principles can be used to guide this valuation if this is supported by a transparent decision framework. This paper proposes that the ICMM sustainable development principles provide appropriate guidance. In addition, a generic framework for decision making is suggested as a complement. Indicators of water management are recognised widely as an integral part of the accountability of minerals companies towards meeting sustainability goals. Less widely recognised are the ways in which sustainability principles can be used to guide decisions on water management which demonstrate growing awareness of its value. This paper illustrates the use of this logic in water issues associated with global sustainability challenges. It then goes on to demonstrate, using examples, that these links exist at all levels of the minerals industry and that indicators of this type are potentially as powerful as those currently being used. The reason for this is that the path from cause to effect is transparent and direct.

Jan 1, 2006

By Pinn N

Geosynthetics is an all encompassing word to describe a number of man-made products usually from hydrocarbons which are used in conjunction with the soil. The specific products are:Geotextiles Geomembranes GeonetsGeogrids GeocompositesIn mine establishment and associated construction work, Geosynthetics have proven to be successful in a wide range of applications. For example, geotextiles are now used to assist with the establishment of access roads, site preparation, haul roads and in connection with the construction of embankments for storage ponds and dams as well as for general hydraulic and foundation engineering problems.

Jan 1, 1990

This paper presents a method for estimating the strength and stability of model coal pillars with bedding planes (weakness planes) inclination. The strength of coal relative to the angular difference between the principal stress direction and bedding planes is considered. The failure behaviour of model coal pillars containing weakness plane inclination by using servo-control Schenck Machine are shown. Uniaxial and triaxial compressive strength of coal specimens are investigated, and test results indicated that the strength of coal pillars depends on the weakness planes inclination with respect to the principal stress direction. However, it is shown that with increasing confining pressure, the effect of weakness planes inclination on the strength of the coal specimens is reduced. An empirical method is given for prediction the compressive strength of coal containing weakness planes inclination. The results of this method are compared with the experimental results and Jaeger theory. Finally, three well-known empirical strength criteria were tested against the triaxial test data for coal containing weakness planes inclination.

Jan 1, 1995

By Grimstone LR, Leach JHJ

An analytical technique is described to identify areas of structural disturbance to coal and interseam strata in coal measures. It is based on exploration borehole data which records seam intersections and interseam lithologies. Computerised data bases have been developed to allow processing of large quantities of borehole records. The case study discussed is located in a tectonic setting dominated by thrust faulting. It provides a mechanism for the identification of low angle and bedding plane faults. In addition it allows the preparation of plans showing the areal distribution of the thrust sheets in the statigraphic section throughout the mine prospect. The technique requires the identification of normal undisturbed depositional thickness of coal seams and interseams to be determined. This is done for coal by the identification of coal ply distribution over the area. For interseam lithologies it is based on sedimentological modelling of lithology distributions, related back to the original depositional environments. Variations from the expected values are interpreted as structural Deformations.

Jan 1, 1986

By T Tran, F Lucien

Supercritical fluids (SCFs) have gained recognition as solvents for the extraction of a wide range of organic materials. Their principle advantages over conventional organic solvents are that they possess much more favourable transport properties and that such properties can be easily altered by adjusting the system temperature and/or pressure. More recently, SCF solvents have been employed in the extraction of metal ions. The direct extraction of metal ions using SCFs such as CO2 is normally not possible due to the charge neutralisation requirement for solubilisation. However, extraction can be achieved with a SCF solvent containing an organic complexing agent as a cosolvent (Laintz et al, 1992; Laintz and Tachikawa, 1994; Dehghani, 1996). The role of the SCF is therefore similar to the role of a diluent in conventional liquid-liquid or solvent extraction processes. In this regard, SC-CO2 is a particularly good diluent since it exhibits good solubility for many organic complexing agents. The extraction of metals with SCF solvents has been examined mainly in the analysis of environmental samples and the treatment of metal contaminated wastes. Nonetheless, some interesting results have been reported recently on the extraction of rare earth metals, which highlight the potential of SCF solvents in mineral processing applications (Laintz and Tachikawa, 1994; Dehghani, 1996).

Jan 1, 2000

High precision GPS systems for mining are accurate to within a few centimetres. Typical systems consist of one or more GPS antenna, GPS boards, sensors to detect the position of the blade or bucket of the machine radios to pick up correction signals, a computer to control the system and a display screen to give instructions and information to the operator. GPS systems offer two benefits û they give information to the operator to get his job done faster and more accurately and they can send information to management about how the job was done. On dozers, GPS systems allow the operator to accurately complete earthmoving jobs with no survey pegs. On hydraulic excavators the systems can be used to accurately locate the position of the bucket teeth for selective mining. On blasthole drills the systems can guide the operator to each hole and record accurate as-drilled plans. By reporting the position of the blade or bucket in three dimensions it is possible to continuously upgrade a mapfile of the excavation. From this file it is then possible to report productivity numbers in real time. High precision GPS works best with a minimum of five satellites visible. This may be difficult in a pit. Systems which also access the Russian GLONASSS satellites offer significantly better uptime. GPS systems will become indispensable for efficient mining operations in the future.

Jan 1, 2003

By H. J. Glass, A J. Cornah

Improving the quality of the variogram helps to improve subsequent estimation and simulation processes. Two strategies for conditioning data prior to construction of the variogram are investigated using data from the Luce iron ore deposit in Canada. One strategy is the classic approach in which the deposit is subdivided into a set of structural domains. The domains are analysed individually and datapairs are recombined to produce a variogram. The second strategy is reconstruction of the deposit at an earlier stage of its history through unfolding. This involves transformation of the Cartesian coordinates into stratigraphic coordinate system. Improvement in the variogram quality, expressed in a decreased weighted deviation from a fitted model, is observed for both types of data conditioning. This indicates that, for the Luce deposit, application of data conditioning could also help to inform the selection of sampling locations.

Jan 1, 2006

THE manufacture of Portland cement on a commercial basis dates back to the year 1824, when Joseph Aspidin, of Leeds, patented his process. It was, however, only within the past 25 years that the cement of to-day commenced its history, and during that period manufacturers have constantly tried to improve the grade of cement.The introduction of the rotary kiln at the opening of this century was the starting point of rapid development in the process of manufacture, and in the quality of the cement produced.Following on the rotary innovation came the wet process. This at first was used only where the raw materials were of a soft nature; but to-day nearly all classes of materials can be treated by this method. Oompared with the dry process, it allows for greater refinement of raw materials, more intimate mixing, better chemical combination, and economy in fuel. Taking advantage of this, the manufacturers in England and America are in a number of cases substituting the wet for the dry process.Subsidiary machinery throughout the factories, such as crushing and grinding mills, have also been vastly improved. The chemists, too, have done their share in the work. Long and careful research has proved the necessity for accurate proportioning of raw materials, thorough mixing, and very careful burning. All these factors combined have given us the product of to-day, which is consistent within very narrow limits, and far superior to that of the beginning of this cement era.

Jan 1, 1926

By C McInnes

The key to successful flotation plant design, production planning and mine/mill optimisation is a solid understanding of the resource to be processed. As advocated by the authors of this paper, the main components of geometallurgical modelling of an orebody and its associated flotation plant are: an ore sampling program and subsequent laboratory testing of these samples in order to extract process model parameters; geostatistical distribution throughout the resource model of the process parameters; calibration of the plant via benchmarking (for existing operations); and plant simulation using a system of process models and the distributed metallurgical parameters (from step two) as the data set.It is important that the grinding and flotation models are linked. For example, a laboratory test conducted on a drill core sample, intended to represent a portion of the orebody, is conducted at a specific grind (represented by a P80). However, when that ore is actually processed through the plant it may well be (and in many cases most likely will be) at another P80. Additionally, the flotation plant residence time will often be determined solely by the grinding circuit capacity and feed slurry density. In the case of SAG mill û ball mill circuits, the fluctuations in tonnage and grind are known to be high. The modelling approach described in this paper allows for changes in the measured flotation kinetic parameters in order to reflect the expected grind as determined by the comminution process.

Jan 1, 2005

Every step on the path from the mine to the smelter invites a comparison between material inputs on one side and outputs plus accumulation on the other. Or put simply, between what you think you have produced with what you find you have at hand. The discrepancy between these sets of comparisons is the error. Following that error in a systematic and objective manner is a way to improve the mineÆs measurement systems, that in turn leads to more accurate accounting for ores, metals and concentrates. Because the control of production is so tightly coupled with the accounting of materials, any lasting improvements in materials accounting will benefit the predictions of materials movements and quality. This translates to more reliable planning and scheduling in stockpile management, logistics, shipping and marketing. The statistical tools described are direct adaptations from the long-standing methods used to maintain the quality of manufactured product in the discrete parts industries. Their use in the process industries, of which mining is one, requires some care owing to the continuous nature of ore extraction and its variable properties. The tools can be used for problem diagnostics and as early warning systems. In common practice many professional staff, in attempting to get a perfect reconciliation between expected and observed results, try to explain away the error or bury it completely. The methodology advocated here requires a different mindset because the error must be given pre-eminence for lasting improvement to be realised.

Jan 1, 2002

Reconciliation of the ore reserve has been an integral part of mine planning since Bougainville Copper Ltd. commenced mining operations at Panguna in 1972. Confidence in the ore reserve is considered essential, both for long term planning of the deposit, and for fair and accurate reporting of the mining resource to shareholders. Recoverable, proven reserves are published annually. Although the ore reserve quoted is based only on diamond drill hole (DDH) information on a 122 metre by 122 metre grid, predictions are regularly reviewed against production. Concentrator results are taken to be the best estimate of grade and tonnage. Surveyed mined perimeters and average blasthole grades are reconciled at the end of each month against the concentrator figures. Predictions of the in-pit reserve are made using an orebody model. DDH and blasthole (BH) sample grades are used to make predictions for both long and short term planning. This paper describes how reconciliations are used to validate ore reserves at Panguna. Development of the orebody model is described, and some of the difficulties encountered in doing reconciliations are addressed.

Jan 1, 1987

By M Maulen, K van Olden, T Elkington

A large open pit is planned at the site of an existing underground mine. Strategic planning work has been undertaken to investigate the project value associated with an expansion of underground operations in conjunction with the proposed pit. Previous analysis determined that any depletion of the available pit resource that changes the optimum pushback sequence has a significant negative impact on overall project value. Therefore, to investigate the viability of an underground expansion requires a system to identify the stope resource that would add value to a combined operation if mined ahead of the pit. The key solution to this problem was to generate a resource model variable that defines the blocks, which have greater discounted value if mined by stoping rather than by the open pit. A key assumption was that the open pit is the main driver of overall project value. From the identified potential underground resource, series of mineable stope shells were generated at a range of cut-offs. This stope reserve data formed the input to a mixed integer program based software tool that was developed and used to optimise the underground mining plan, at conceptual level, for various project configurations. A dynamic programming tool was then applied to evaluate the optimum value of a combined open pit and underground operation. The overall objective of this project was to determine the strategic plan that yields the optimum value for a combined undergroundûopen pit operation. The results provided a clear focus and direction for more detailed design and planning.

Jan 1, 2009

By A Scott

Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data û especially with semi-automated data acquisition by instrumented mine equipment. However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model. An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc not only have many areas of interest but also have very different conceptual models by which they evaluate performance. It is too ambitious to attempt to bring all of these cultures together û in a single step. However, the success of the Mine to MillTM project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from orebody model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling. However, in both cases the data collected is strongly focused on the technical requirements û not on the business model. This paper considers how to define at least some of the key decision points in terms of some case studies. Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning.

Jan 1, 2002

By J J. Cilliers, K Hadler

Froth structure and stability are known to play important roles in determining mineral flotation recovery and selectivity. However, measuring froth stability in a consistent manner remains a significant challenge, especially at an industrial scale. Following preliminary tests on a copper concentration plant, a quantitative dynamic stability measure is investigated in this study in order to extend the results over a wider range of conditions and on a different orebody. The technique is based on the Bikerman foam test and uses a non-overflowing froth column to quantify froth stability. Experiments were carried out using an automated version of the froth stability column under different operating conditions. Air flowrate was the key operating variable. Tests were reproduced on a single flotation cell of a Platinum Group Metals concentrator. The froth stability factor, , was measured for each operating condition, and compared with the air recovery in the cell, , which was measured using image analysis. The froth stability column results gave the same trends as image analysis. In particular the froth stability factor was found to be linearly related to the actual fraction of air overflowing the cell. The metallurgical results clearly indicated that changes in air flowrate result in variations in flotation performance that can be attributed to changes in froth stability. The results showed that high froth stability conditions occur at intermediate air flowrates, and result in improved flotation performance. It is found that the froth stability column is a simple, cost-effective and reliable method for quantifying froth stability, and for indicating changes in flotation performance.

Jan 1, 2005

By P J. A Lever

This paper presents details of CRC MiningÆs work with waterjet assisted blasthole drilling. The objective of this work was to investigate techniques that reduce the cost and increase the productivity of blasthole drilling. The focus is on a technology that uses a high pressure waterjet to assist the conventional rotary rock cutting action of a tricone drill bit. The potential benefits of this technique are increased productivity, reduced drill bit wear and reduced hole deviation and hence improved quality of drilling. This paper describes the results of a laboratory based experimental program comparing conventional tri-cone drilling performance to the proposed waterjet assisted approach. Additionally, work has been completed looking at the more practical issues around the collection and sampling of drill cuttings and water recovery (recycling) when drilling with a waterjet. These studies have demonstrated that waterjet assisted drilling can significantly increase the rate of penetration over conventional rotary drilling. For the best-case experimental result, the relative improvement was over 40 per cent. More importantly, it is a starting point for examining alternative uses of the additional drill productivity obtained from waterjet assisted drilling. For example, increased drill productivity could be used to improve rock fragmentation by drilling a tighter blasthole pattern in the same time period. an existing drill fleet, then the drill fleet size could be reduced, or improved rock fragmentation could be achieved by drilling a tighter blasthole pattern within the same time period.

Jan 1, 2004

By P Walton, L W. Armstrong, D P. Blair

Sydney is the capital city of NSW and has a population of approximately four million people. Eighty per cent of the cityÆs water is supplied by Warragamba Dam, which is situated some 75 kilometres south west of the city centre. A risk assessment was carried out on the dam and future predictions of water flows into the catchment area showed that there was a risk of a one in 700-year flood not being contained by the dam. The predicted loss of life and property damage warranted the construction of an auxiliary spillway on the eastern side of the existing dam to cater for any uncontrollable influx of water. A test blasting program was instigated and the blasting parameters were established that would lead to routine production blasting of the sandstone rock making it more cost effective to excavate. Blast induced vibrations were a concern to the owners and the dam wall and ancillary infrastructure was instrumented with sensitive vibration monitoring equipment during the test blasting phase of the operation. Once the blasting parameters were established from the testing program production blasting was carried out on a daily basis to maintain æstockpileÆ of fragmented ground for the excavation equipment. Blast vibration models were developed to predict vibration levels for more sensitive areas of the dam to give the operators more confidence in their operations. The blast induced vibration levels recorded did not cause any structural damage to the dam wall and the waveform frequencies of the blasting operation were much higher than that experienced during a recent earthquake. The integrity of the SCAÆs assets were at no time jeopardised.

Jan 1, 2001

By C Hertle, B Goebel, R Fabre

The mining industry maintains a ælove-hateÆ relationship with water. Dewatering, aquifer, water disposal, irrigation, process water, tailings water, run-off water, seepage, leachate and sumps are all terms that are used on a daily basis in the mining industry, highlighting the numerous water usages on site and their associated quality. According to the Australian Bureau of Statistics (2001), each year the mining industry consumes over 530 000 ML of water. The increasing recognition of water as a limited and valuable commodity, and the associated environmental concerns with the management of water disposal to the environment has led the industry into improving on-site water management. Progressively, water balance models and water reuse strategies are being developed, incorporating more sophisticated water treatment processes. By way of example, membrane technologies, once restricted to industries such as the pharmaceutical industry or the drinking water industry, are now entering the mining world with the aim of producing clean water of suitable quality for ore processing or for advanced treatment prior to release to the environment. This paper will provide a review of the threats and opportunities linked to water use and recovery/reuse in the mining industry in Australia. It will open with an overview of current water usage and associated quality for various mineral industries and continue with identifying the threats and limitations associated with the quality of available water. It will then present how newly developed water treatment technologies and assessment tools can be incorporated into the system to enhance the recovery and reuse of water on site, reduce the risks associated with securing long-term water supply and further improve production, environment and safety (health risk control).

Jan 1, 2006

By A Califice, E Pirard, M Benzaazoua, R Mermillod-Blondin

Image analysis is more and more considered as a powerful tool for quantitative analysis of ores and concentrates. Apart from being very much dependent upon the quality of the imaging principle and the adequacy of the imaging sensor, quantitative image analysis is also the result of a long chain of material, image and pixel sampling strategies. The most reliable way to demonstrate the accuracy and the precision of modal analysis obtained from images is probably to use a blended material with known proportions of pure minerals and confront the results obtained from different analytical tools. This operation has been performed on a series of mineral blends mimicking the tailings of a flotation operation in a plant operating on massive sulfide mineralisation. The intention was to be able to better predict acid mine drainage potential from direct mineralogical observations. Selected sulfide minerals: pyrite (Py), pyrrhotite (Po), chalcopyrite (Cp) and sphalerite (Sp) were mixed as variable amounts within gangue minerals (quartz, calcite, dolomite and siderite). Typical blends contained six to ten per cent (Py); one to three per cent (Po); 0.5 to one per cent (Cp, Sp); 15 to 40 per cent carbonates and 40 to 75 per cent quartz by mass. The 1000 gram blends were carefully sampled and prepared for X-ray diffraction, chemical analysis by ICP-AES and optical microscopy image analysis (OMIA). Results obtained for the different analytical techniques are compared and discussed revealing the limits and strength of each method in the accurate quantification of sulfide and gangue minerals.

Jan 1, 2008

By Meyer T

Sunburst PCF (Penetrating Cone Fracture) technology has recently undergone extensive underground field trials at Leinster Nickel Operations, Western Australia. Trials with the Sunburst machine started in September 1994 and continued through to December 1994 during which approximately 130 metres of tunnel were developed. The Sunburst technology was used to excavate sub-levels through ultramafic nickel ore for future sub-level caving operations at the Perseverance nickel mine. The Sunburst machine demonstrated reasonable instantaneous advance rates, however, there are still a number of future developments/design changes which need to be addressed prior to the PCF technology being trialed again in a production environment. This paper benchmarks conventional drill and blast at Leinster against the Sunburst Excavator machine performance within similar tunnel dimensions and rock conditions. In addition to productivity and cost information; environmental considerations, support and labour requirements are also discussed. Problems with the current machine design are highlighted and possible future design changes are suggested. The Sunburst machine could be a suitable technology for advancing development through weak to moderate rock conditions and may also reduce overall support costs. With the potential for automation and the ability to reduce rock damage into the development tunnel walls, it is proposed that the Sunburst machine warrants further consideration.

Jan 1, 1995