Search Documents

By Hawes GW

Until 1980 copper, lead and zinc sulphide slurries have been success- fully dewatered for rail and sea transport for many years at the Rose- bery site of North Broken Hill Holdings Ltd. utilizing conventional vacuum disc filtration systems. An upgrading and mill expansion program completed in 1981, which also permitted the introduction of ore streams changes, had resulted in difficulties dewatering copper and lead sulphide slurries to comply with transportable moisture limits. Following an extensive investigation which included both laboratory and pilot plant testing a program was commenced to replace the 2 vacuum disc filtration systems with 2 pressure filtration systems for use on copper and lead slurry dewatering and also to retain other existing vacuum disc filters as standby. An analysis of mill operations performance resulted in slurry storage tanks with a capacity equivalent to 20 hours of normal production being incorporated into the project. The pressure filters are mounted above the concentrate stock- piles. A sealed sloping floor incorporating launders is used to prevent any accidental contamination of the concentrate from pipe leakages, spillage, or from water hoses used for clean up purposes around the area. The project was completed in 1985 and operating performance has been better than that predicted from testwork. Equipment availability at 95076 together with the slurry storage capacity provided results in minimal requirement for the standby vacuum filtration system. Some typical operating results are given.

Jan 1, 1988

As an environmental "pollutant", noise is different. For one thing, it is localised (as opposed to transfrontier) and, for another, relatively low levels can trigger very strong human reaction. The reactions, which are annoyance-based, range from mild to violent and do not always correlate well with the levels experienced. This paper draws on technical aspects of noise to consider control and control principles and balances them with the subjective nature of the perceptions and reactions. It is critical to bear in mind that health effects resulting from noise are secondary to the primary human reaction. It is also important to appreciate that annoying noise levels are usually well below those which cause hearing loss. Large mines tend to be remote from cities and towns and the country surrounding such mine sites is often inhospitable. In general, residences near large mines are committed for use by mine personnel and annoyance from mining noise would be rare. Noise problems at long term operations are often a result of secondary activity or land use. As a pioneer mining community develops, secondary and service industries may be established and a township created. With changes in way of life, the perception of problems also changes. Therefore, it is never too early to plan for noise abatement, particularly because noise is only one of a number of environmental and community concerns. Ihny environmental problems are associat- ed with development or expansion of smaller open cut facilities such as hardrock quarries. There is an ever-present need to reduce product cost by mining or quarrying deposits close to the end user and many local authorities have to operate quarries for undertaking their civil engineering responsibilities.

Jan 1, 1987

The methods used by the Anglo American Corporation for analysis of long-term metal markets and prices are described. The principal factors affecting the relationships between production costs and metal prices are analysed. These are firstly the type of market, - speculative or consumer commodity, free market or subject to price control; and secondly the rate of growth of demand for the metal. It is shown that virtually all metals will have relatively low rates of demand growth for the foreseeable future, due to market saturation, increased economisation, substitution and product obsolescence. Metal prices have a clear dependance on production costs, however forecasting future costs is by no means simple; amongst other things, account must be taken of changing exchange rates, inflation rates, and the potential for operating more efficiently. The paper concludes by giving brief assessments of the long-term future for aluminium, copper, zinc, nickel and tin.

Jan 1, 1986

This paper comprises a discussion of standards for comparing conditions in mines, of methods for measuring the flow of air, of a comparison of fan performances, and the application of these matters to mines in Western Australia.UNDERGROUND CONDITIONSIn approaching the question of mine ventilation one naturally searches for some standard by which to measure the conditions in a mine.There are several clauses in the Mines Regulation Act defining the conditions which are permitted. The quantity of CO2 is limited to 0·25 by volume, but the estimation of CO2 involves a chemical determination and is not suited for general use in a mine.The maximum temperature is fixed at 87 0 F. (dry bulb), and at 80° (wet bulb). The reading of temperature is easily done in the working places, and this is a very valuable and practical test of the conditions in a mine.The wet bulb temperature is probably the most important factor in determining working conditions. It is obvious that human life cannot be sustained for any appreciable period if the wet bulb temperature is above blood heat (about 97°F.). In places where the wet bulb temperature is 90°F. there is danger of heat stroke.In places where the air in a mine is still, the wet bulb temperature rises to a value close to the rock temperature.Adequate ventilation cools the workings by transference of heat from the rock to the air stream, and the temperature...

Jan 1, 1939

Christmas Island "C"-grade phosphate consists essentially of the minerals crandallite and millisite. Although containing over 25% P205, this material is not suitable for the manufacture of water-soluble phosphate fertilizers by conventional processes, because of its high iron and aluminium content Cover 25% total R203). In order to produce a water-soluble fertilizer from such material it is necessary to separate the iron and aluminium from the phosphate, which must report in a product acceptable as a fertilizer. Several processes were studied in detail. The first used ion exchange for dissolution and separation and yielded diammonium phosphate; processing costs were high compared with conven- tional processes based on apatite. The latter processes have basically simple flowsheets and cost of processing is low when compared with the costs of the raw materials. The need to separate iron and aluminium from the phosphate introduces additional complexity into the treatment of the C-grade material. The higher processing costs might be justified, however, if alumina could be produced as a byproduct. Two proposed processes have been developed in which: 1. hydrochloric acid is used for dissolution, and solvent extrac- tion for the separation of ferric chloride from phosphoric acid. Aluminium chloride is precipitated and hydrolysed to recover alumina and hydrochloric acid. 2. sulphuric acid is used for dissolution and aluminium is crystallized as ammonium alum. The phosphate is produced as an ammonium phosphate-sulphate fertilizer. High purity alumina can be obtained by treatment of the recrystallized alum. The technology of these processes is described, and their broad economics discussed briefly.\

Jan 1, 1971

Based on twenty years of experiences of applying computers in mine water engineering in Hungary, a program package was developed for home utilization and for other users abroad as well. This program package has been adapted to the CAD System of Coal Mining of COMECON countries. The main features of the "mine water subsystem" in the CAD System of Coal Mining and short descriptions of the key programs of the package are presented in this paper. Foreword The serious water problems of Hungarian mining pressed and/or stimulated its professionals to apply computers for supporting their problem-solutions. The first trials of these computer applications in mine water engineering were dated from the sixties. Owing to its twenty years of experiences in computer appli- cations in mine water engineering the Central Institute for the Development of Mining in Hungary was requested to work out the "Subsystem of Mine Water" for the Computer Aided Design System ('CAD) of Coal Mines in COMECON countries. This paper gives a brief presentation on the main features of this "subsystem"with reference to significant components.

Jan 1, 1988

Neutralisation, normally using lime, is the most widely used method for treating high flows of acid mine drainage (AMD). Lime costs can be very high however. If carbonate sources could be used to achieve pH values above six, costs could be greatly reduced. For example, use of locally quarried limestone at Mt Lyell could potentially reduce alkali costs from about $A 3.5 to $A 1 million/year. Methods for enhancing the effectiveness of limestone and magnesite for neutralising Mt Lyell and Savage River AMD respectively have been examined through a series of investigations. Small-scale testwork found that the maximum pH economically achievable with ground limestone was about five, due to slow dissolution rates and surface armouring. The problems of surface armouring were greatly reduced by the use of crushed limestone or magnesite at high pulp densities (75 per cent solids w/w), enabling pH values >6 to be achieved in a practical time frame. The use of particle sizes in the range 6 mm and finer also reduces costs by avoiding the need for grinding, and reduces the problems of solid-liquid separation and solid recycling that arise if large additions of ground carbonate are used. Pilot scale tests were carried out using tumbling drum reactors with limestone and Mt Lyell AMD and a pulsed-bed static reactor with magnesite and Savage River AMD. pH values averaging 6.2 and 6.4 were achieved with Mt Lyell and Savage River AMD respectively. Approximately 80 per cent of feed acidity was neutralised. A preliminary engineering design and cost estimate has been completed on the pulsed-bed reactor and shows that the concept is technically feasible and, if results are confirmed, economically attractive. Further pilot testing is planned.

Jan 1, 2002

By Kohra A, Shoji S

The amount of copper production by flash smelting process occupies about 17% (equivalent to 1.4 million t/year) of total free world production. In Japan, 650,000 tons of copper is produced annually by flash smelting. This is 65% of the gross copper production of Japan. To reinforce pollution control, promote energy saving, and enhance production efficiency by increasing the size of furnaces, conventional blast furnaces and reverberatory furnaces are being replaced with the flash smelters worldwide. The Ashio Smelter started copper production in 1884 and developed in association with the Ashio mine. In those days, the Ashio smelter produced copper by using the blast furnace process designed for the high-grade ore from the copper mine. At that time, this process was specialized in Japan. In 1956, for the first time in Japan, the Ashio Smelter introduced the flash smelting process developed by Outokumpu Oy of Finland (it is suitable for treating the copper concentrate, producing sulfuric acid and improving production efficiency). The flash furnace in Ashio, the first ever in Japan, had a capacity of 230 t/day for copper concentrate and was operated up to 1962. During this period, various operational troubles were solved, and further improvements were made; and, in 1962, a Furukawa-type flash smelting furnace was completed in Ashio. This improved version of a flash furnace had a capacity of 450 t/day. There was one flash furnace and one waste heat boiler, which were arranged in a unique pattern for that time. This furnace may be said to be the prototype of the present flash smelting process in the world.

Jan 1, 1987

A metallurgical balance drawn around a mineral processing plant or smelter must involve all process streams crossing the plant boundary. Modern sampling theory, as formulated by Gy, and sound statistical method can be used to determine the uncertainties in the observed assays for the set of balance analytes and in the mass flow rates of the process streams for the balance period. These uncertainties can then be used together with the material balance equations to arrive at adjusted component mass flows that satisfy the material balances exactly. To determine whether or not the data is consistent with the level of uncertainty in the data and with the material balance equations, a goodness of fit test is applied. This goodness of fit criterion is the principal tool to quantify the quality of the material balances. The mathematical structure of the statistical material balance problem poses a number of challenges. For example, while the variances of the adjusted component mass flows do not vanish, the variances of the sums of the adjusted component mass flows about each balance node do vanish, simply because the balancing computation demands that the balances close exactly. Even though it can be shown that the variances of the adjusted component mass flows are always lower than the estimates for the corresponding unadjusted component flows, it is still not possible to construct a confidence interval on the component mass flow into (and out of) a balance node using the adjusted component flows. On the face of it, such a confidence interval is exactly what is most desired from the balance calculations. The problem arises because the balance problem is a data adjustment rather than a parameter estimation problem. It is possible, however, to calculate the recovery of a component to a product stream and determine a confidence interval for the recovery value. It is also possible to calculate an uncertainty in the mass flow of any balance species in any process stream, before and after balancing.

Jan 1, 2005

Using a Jarrell-Ash "Compact" direct reading spectrometer, analyses were made of a wide variety of rocks ranging from acidic to ultrabasic types. Statistical evaluation suggests that accuracies comparable with the values obtained by the rapid chemical methods used by the United States Geological Survey will be obtained.The spectrographic method involves fusion of the rock with lithium tetraborate, strontium being incorporated in the flux as the internal standard. The resulting bead is ground with graphite and pressed into a pellet. The counts obtained on two standard pellets are used to correct for instrumental drift.Background readings are made at 4109 Å and corrections for background are made to all lines. Corrections for matrix interferences, both by chemical suppression and optical enhancement, are made. The three corrections of drift, background, and matrix are incorporated into one general expression which has been programmed on magnetic cards, each element requiring a separate card. The cards are placed individually into a desk top computer (an Olivetti Programma 101), which enables true counts to be calculated from the "readout" counts, and the element concentration is then obtained from computer-printed tables by referring to the appropriate value of true counts versus concentration. These tables were prepared by making a polynomial regression analysis of the spectrographic results from 50 standard and analysed samples, a curve of best fit being chosen for each element.The regression coefficients, usually of a fourth or fifth degree equation, together with other relevant data, were fed into a large computer, programmed to print out tables of concentration versus true counts. This technique enables the results obtained to be based on mathematically-derived values rather than on hand-drawn calibration graphs, giving greater inherent accuracy. The technique has been shown to give results of good accuracy and acceptable precision suitable for many geological and geochemical exploration programmes involving the analysis of many rock samples of different types.

Jan 1, 1969

By M Thomas, M Caccetta, C Laukamp, A Hacket, M Jones, A Rodger, M Verrall, R Hewson

A mineral systems approach was used to interpret precompetitive airborne mineral mapping geoscience data for iron oxide copper gold (IOCG) exploration in the Starra area, Eastern Succession, Mount Isa Inlier. Selected minerals were chosen to map possible source rocks/fluids as well as intersecting structural/fluid pathways that could have transported mineralising fluids into domains of contrasting rocks/fluids where there was potential for physicochemical gradients to precipitate metals. Ferric and ferrous iron contents and white mica abundance were useful mineral criteria to identify theMount Dore Granite of theWilliams-Naraku Batholith as a potential source of æoxidisedÆ fluids rich in Fe, K and potentially Cu-Au. The Mount Dore Shear Zone (MDSZ) intersects the western margin of this granite with the highest contents and changes in composition of the white mica are peripheral to this contact within the granite. This together, with the fact that the entire N-S length of the MDSZ in the study area (~16 km) is abundant in white mica are evidence of K-rich fluids had preferentially moved along this pathway. To the south, the MDSZ intersects a domain comprising massive ironstone bodies as well as numerous graphitic horizons. This interpreted æreducedÆ domain is well mapped using the æopaqueÆ mineral products, as well as by white mica, which is pervasively developed and extends 2 km either side of the MDSZ fault into the meta-sedimentary sequences. The chemistry of this white mica also changes progressively away from the MDSZ, becoming more Si-rich (longer wavelength) towards the contact with massive ironstone bodies in the west and the graphitic units in the east, both of which represent sites of known Cu-Au mineralisation. Beyond these contact zones of interpreted æoxidised fluidsÆ with reduced rocks/fluids, there is either a rapid change to Si-poor white mica and/or no white mica developed, ie major æchemicalÆ gradient change. These mineral mapping results provide evidence for a direct link between possible source rocks and sites of IOCG metal deposition as well as extending the associated alteration zonation which had previously been mapped/published at the metre-scale to the kilometre-scale. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By M J M Cunningham, M Greentree, J H Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Palaeozoic rocks of north-eastern Laos are an attractive target for gold explorers due to the complex tectonic history and lack of past exploration in the region. Alluvial workings along the Nam Xiang River and its tributaries have highlighted the potential for gold mineralisation in the Vieng Kham region. The Nam Xiang River follows a regionally-extensive NNE-striking thrust fault. Adjacent to the Nam Xiang fault, the dip of the main foliation steepens, and in many places the stratigraphy is overturned as a result of this faulting.United Minerals and Mining Company conducted a regional exploration program to explore for gold. This included stream sediment and rock-chip sampling, and airborne geophysics. Geochemical anomalies were followed up with more detailed exploration, including geological mapping and soil sampling. Despite the relatively deep weathering profile, gold mineralisation is associated with a low-level but well-defined gold-in-soil anomaly. Drilling has shown that gold mineralisation occurs on structures and fabrics parallel to the main Nam Xiang fault. The highest gold grades are associated with brecciated sandstones that have experienced strong carbonate alteration. This suggests that late-stage structures such as the Nam Xiang fault are the major control on gold mineralisation in the region.CITATION:Greentree, M, Cunningham, M J M and Liu, J H, 2015. Gold mineralisation along the Nam Xiang fault, Vieng Kham Project, North-east Laos, in Proceedings PACRIM 2015 Congress, pp 177–182 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Cerutty L

To those who have been engaged in the construction of mining and metallurgical plants during the war and post-war periods, it is quite unnecessary to point out the large increases and violent fluctuations in prices of basic commodities and the steady and persistent rise in labour costs. It may, however, be of interest to present these facts in graphic form, and survey the relative heights of the various maxima and the lead and lag of individual waves. Since Descartes demonstrated for us moderns the analogy between geometric form and algebraic statements, the two-dimensional graph has found widespread application. Mathematicians have developed for our information, if not for our confusion, the triangular diagram and the solid three-dimensional figures, which have proved so useful, at least in the hands of the metallurgists at Port Pirie. The model (Plate 1.) which is exhibited here does not pretend however, to indicate the connection between any three inter-related variables, and it is not proposed to burden members with any abstruse mathematical expression for the irregular surface of the blocks. While time is an ordinate common to all sections of the model, each illustrates separately the variation in cost of some particular quantity between the years 1914 and 1922. It is an easy matter to record such individual variations, but it would be an impossible task to state any equation describing accurately the dependence ot the prices, say, of hardwood or of galvanized iron upon that of labour at any particular point of time. The cost of living curve, which has attained such prominence, if not notoriety, in the last few years, is the result of an attempt to show the mass-effect of the components. It is the difficulty found in "assigning the correct weight to the separate items which makes the aggregate curve somewhat misleading at times.Turning to the model, it will be noticed that each section consists of half a dozen pegs.. The first in each row,that coloured red, represents the cost of some particular quantity, such as bricks, timber or coal, at Broken Hill in 1914. The next peg, that coloured blue, represents proportionately prices for that quantity in Hobart during...

Jan 1, 1922

By Robinson WB

An accurate and rapid assessment of coal resources, such as that provided by computer modelling, forms an intergral role in evaluating CSR's coal deposits for future development. An in-house system utilising a number of geological, engineering, costing and financial evaluation routines has been developed for DEC VAX computers. The system is currently being upgraded and enhanced to meet the demands at the various mine sites. Computer modelling of the geology is performed on encoded drillhole information and coal core chemical and physical analyses. A conceptual mine plan is formulated then digitized and superimposed on the geological model. Insitu and product coal reserves and qualities as well as overburden and parting quantities are then calculated for each strip or block. These strip parameters are then transferred to the mine scheduling routines to determine the most efficient mining sequence for the mine plan. Cost factors and scheduling data for equipment specified in the conceptual mine plan are used in the mine costing subsystem. The financial subsystem then evaluates the likely return on investment. Future enhancements to the system include improvements in the response time through the introduction of interactive graphics, the direct interfacing of geophysical and analytical data, and further development of a geotechnical'database.

Jan 1, 1983

By Derham DW, Newcombe LA

The operations of the Mount Morgan gold tailings retreatment plant were significantly improved in 1984 by the desliming of the CIP plant feed, which reduced cyanide consumption and increased percent gold dissolution. Subsequently, the development of slimes treatment, incorporating gold leaching from slimes solids by copper cyanide complexes in the process water, and gold adsorption on to carbon in an environment lacking free cyanide was successfully implemented. Mount Morgan was initially mined for gold commencing in 1882 on the auriferous ironstone cap to the sulphide ore body. During the history of mining and processing at Mount Morgan the operations have developed through numerous phases of gold and copper production, operating almost continuously through until the final closure in late 1990. The final phase of processing was the retreatment of tailings, predominantly flotation tailings accumulated since the 1930s, for the recovery of gold and minor silver. Tailings retreatment commenced in 1982 with the commissioning of a 10 000 tonnes per day CIP plant to treat some 40 million tonnes of tailings at an average grade of 1.08 g/t Au. The initial operations were hampered by high cyanide consumption and poor gold dissolution on the mixed siliceous/pyritic tailings. The successful development and implementation of the desliming of the CIP plant feed in 1984 (as described by Parsons and Hampshire, 1986) reduced cyanide consumption by 40 per cent, and raised gold extraction by 13 per cent points by virtue of significantly higher dissolved oxygen levels. The finer portion of the reclaimed tailings were deslimed by eighty 100 mm diameter AKW cyclones, with the desliming cyclone overflow thickened in a Warman 30 in diameter thickener for water recovery and slimes disposal. Operation of the desliming plant involved the discarding of a slime fraction representing about 15 per cent of the reclaimed feed. Although gold-bearing, the high content of cyanicides and oxygen consumers within the slime negated any conventional treatment of this stream with free cyanide for gold recovery. The natural lixiviant behaviour of the soluble copper cyanide complexes for gold, which was extremely evident at Mount Morgan, directed efforts in this area. Enhancement of gold leaching with a deficiency or near absence of detectable free cyanide, but with significant levels of copper cyanide complex from recycled process water were examined. Adsorption of this solubilised gold onto carbon in a similarly difficult environment required close examination.

Jan 1, 1993

By J Lane, D J. Barker, B Pei

Queensland Alumina Limited (QAL) is the worldÆs largest producer of smelter grade alumina, located in Gladstone, Queensland, Australia. The plant employs evaporative cooling towers for waste heat rejection. Process water requirements include red mud residue disposal, steam venting to the atmosphere and Calcination feed moisture. Raw (untreated) water consumption in 2001 was 37 700 m3/d or 3.8 m3 per tonne of production. The Gladstone region experienced a water shortage in the period 2001 to 2003, resulting in progressive water restrictions. Industry operated under a ten per cent restriction from April 2002 and in November 2002 a 25 per cent restriction came in force. The maximum restriction level of 50 per cent was anticipated for the middle of 2003. Water restrictions of these magnitudes have the potential to result in significant production limitations, which would have major economic consequences for QALÆs owners, customers, suppliers and employees. Therefore it was imperative that measures be found to mitigate the impact of these restrictions. Furthermore, as one of the largest water users in the Gladstone region, QAL had an obligation to the community to minimise water usage as much as possible. A thorough analysis of water usage on site was conducted, focussing on all water streams leaving the plant. The philosophy used was that by minimising water outputs, the inputs would follow suit. Where possible, preference was given to solutions that provided lasting water savings. This occurs when the value of the water saving justifies the project cost, irrespective of water restrictions. By June 2002 an average water saving of 19 per cent was achieved, almost double the required saving. By end November 2002 further projects had increased the total water saving to 29 per cent, mainly through the re-use of GladstoneÆs municipal treated effluent as wash water. Further measures to reach the target of 50 per cent reduction were investigated. The evaporative cooling system was to be replaced with seawater cooling, using cooling towers to minimise the seawater pumping cost. Another benefit of this concept was the ability to dispose of the cooling tower bleed stream with the existing system for neutralised red mud disposal. This would avoid the need for an additional environmental outfall from the plant. In February 2003 the Gladstone region received over 500 mm of rain, which boosted water reserves to five years supply at forecast usage rates. This led to the lifting of all water restriction. As most of the implemented water savings measures are economically viable in the absence of water restrictions, raw water usage at QAL is still less than 75 per cent of pre-2002 levels.

Jan 1, 2003

The decision to contract or owner mine should be independent of, and should be made before, definitive estimated cost comparisons could be available. There is substantial potential risk of estimated cost comparisons being flawed due to difficulties in compiling comparable estimates for differing business objectives, errors and omissions or because of significant bias. In the current economic environment, escalating cost pressures potentially lead to increased incidence of disputes in mining contracts. The apparent cost of contractorÆs profit and overheads has tended to become more significant to owners. Economy-driven trends towards higher levels of performance and commercial risk for contractors, and the potential for more adversarial, difficult management; with attendant disputation between contractors and owners, have encouraged development of so-called ærelationship contractsÆ û partnering or project alliance contracts. The paper discusses the issues, circumstances when owner mining or contract mining is favoured and perceived advantages and disadvantages of contract mining. The implications of owner-perceived core business and core skills and outsourcing are also discussed. Techniques of introducing objectivity into the decision to owner or contract mine using matrix analysis or benefit comparisons are described. A disciplined procurement process should deliver a decision to owner or contract mine independent of, and prior to, any definitive comparison of estimated costs. A generic procurement process model is provided as a basis for discussion. Risk is discussed generally and as a significant factor in comparison of estimated operating costs. Consideration of risk and any prudent cost treatment are promoted as necessary pre-requisites to any comparison of estimated costs. The paper develops the concept that the decision to owner or contract mine should be based on real benefits that become obvious in the early stages of the development, particularly the procurement process; and before definitive estimated cost comparison can be available. In the context of this concept estimated cost comparisons tend to be confirmatory. Problems with comparing estimated ownerÆs operating costs with tendered contract prices are also discussed, particularly recovery of capital cost of equipment; and the owner minerÆs trade-off of operating risks for the residual contractorÆs margin attributed to overheads and profit. The paper concludes that sole reliance on a comparison of estimated ownerÆs operating costs with tendered contract prices in deciding to owner or contract mine is questionable and likely driven by a need to satisfy specific in-house customers.

Jan 1, 2003

Exceptionally weak ground, usually associated with faulting, unanticipated groundwater pressures or flows and exceptionally high stress concentrations are some of the hazards which confront the underground excavation engineer. One or more of these hazards can seriously delay or even halt a tunnel or mining project, and methods for predicting these hazards are urgently required, particularly for projects involving high speed drill and blast or tunnelling machine excavations.This paper explores the current availability and the potential for the development of tools and techniques for the prediction of these hazards. It is concluded that systematic and automated geological data collection and interpretation represent the most promising avenue for development. It is suggested that there is room for the use of expert systems in which the computer is used to assemble and organize practical underground excavation experience into an interactive decision making system.

Jan 1, 1985

By M H. Randell, J B. Haines

The Honeymoon Uranium Project comprises the Honeymoon Deposit,Goulds Dam Deposit and Yarramba Prospect in the Southern Lake Fromeregion, South Australia. Both the Yarramba Prospect and HoneymoonDeposit (which includes Honeymoon and East Kalkaroo orebodies) arelocated in the Yarramba Palaeovalley. The Goulds Dam Deposit is about75 km north west of Honeymoon, in the Billeroo Palaeovalley. Exploration for sediment-hosted uranium began in the area in the late1960s, culminating in the discovery of Honeymoon and Goulds Dam inthe early 1970s. In 1982, a 25 L/s demonstration plant was built atHoneymoon to confirm suitability for in situ leaching. The project was put on hold in 1983 due to changes in government policy. Southern Cross Resources Australia Pty Ltd acquired the project in mid 1997. Roll-front deposits form from a migrating geochemical cell, anadvancing reduction-oxidation interface between oxygenateduranium-bearing groundwater and its reduced aquifer host. The source of metal is uranium-anomalous granites, which were eroded fromsurrounding ranges. The weathered granites and resultant sediments are stripped of uranium by oxidised groundwaters, to form solutions carrying uranyl carbonate complexes. The solutions percolate down-slope through permeable sand zones until contacting a reduced environment where uranium precipitates. Uranium mineralisation occurs interstitially between and as thin coatings on sand grains, usually in the form of uraninite or coffinite. The palaeovalleys (previously termed palaeochannels) are incised intounderlying Cambrian/Precambrian basement rocks and filled withsemi-consolidated, largely un-cemented, Tertiary sediments of the Eyre Formation. The late Palaeocene to middle Eocene Eyre Formation is the basal unit of the Tertiary succession in the Callabonna Sub-basin of the Lake Eyre Basin. Further to the north, the Lake Eyre Basin overlies the Jurassic-Cretaceous Eromanga Basin, which comprises much of the Great Australian Basin. Eyre Formation sediments are in turn overlain by the late Tertiary Namba Formation and terrestrial Quaternary units. At Honeymoon, the Eyre Formation includes immature, pyritic,carbonaceous sands and gravels interbedded with lignite andkaolinite-illite-montmorillonite clays. It was deposited by braidedstreams during epeirogenic uplift of the Olary Ranges, accompanied bysubsidence of the Lake Eyre Basin. The Eyre Formation comprises aconsistent stratigraphy of interbedded sand and clay units that arecontinuous over the Honeymoon Deposit but with local variationindicating some hydrological connection between aquifers.In the Honeymoon orebody, uranium occurs within coarse-grained,pyritic sands where the basal sand pinches out between overlyingcarbonaceous clay and the southern palaeovalley slope. Its characteristics are typical of the well-developed, planar limb of a roll-front uranium deposit. Zonal changes related to the reduction-oxidation interfaces across the deposit are readily observable. The orebody extends for nearly 1000 m along the valley margin, is 400 m wide at its maximum and averages about 6 m in thickness. The East Kalkaroo orebody also lies near the southern margin of theYarramba Palaeovalley. It extends discontinuously for approximately 3.5 km and averages 200 m width, with significant uranium present in the Middle as well as the Basal Member. The Billeroo Palaeovalley extends northward for 40 km sub-parallel tothe western side of the Benagerie Ridge, is up to 5 km wide and hasgently dipping banks. Eyre Formation within the palaeovalley isconcealed beneath 90 m of Quaternary and Namba cover, isapproximately 40 m thick, and is sub-divided into three upward-finingunits, which are remarkably similar to the Yarramba Palaeovalleysequence.

Jan 1, 2001

By M Elias

Management of risk has always been an integral part of successfully executing engineering and construction projects although formal recognition of the discipline of risk management is a relatively recent development. This paper describes the establishment and application of a proprietary business risk management framework for FluorÆs global engineering and construction business.

Jan 1, 2003