Search Documents

By S Mitchell

Jetcrete Australia Pty Ltd, shotcrete contractor took the initiative in 2008 to discontinue the use of ‘road registerable’ concrete trucks for all underground works in Australia and internationally.The rationale for this decision was basic, safety. Historically these vehicles have been and still are involved in far too many accidents; this obvious trend needs to be addressed by engineering out the root cause of the problem which in this case is suitability for purpose.Road registerable concrete trucks have been widely used for the delivery of concrete in Australian mines for many years prior to and after the inception of wet shotcrete as ‘in cycle’ ground support in underground excavations around 1992. With this inception came a wide interest in the shotcrete process and an influx of new shotcrete contractors, all using road registerable concrete trucks to deliver the large volumes of Shotcrete required for these services and in turn largely increasing the use of these vehicles underground. The road registerable concrete trucks were difficult to control and each trip underground required the operators to maintain good management of the inherent risks. We virtually had no reasonable alternative for the industry and could only encourage the operators to drive with soft controls such as, reducing overall speed to a maximum of 15 km per hour when declining, regardless of the road conditions, coming to a complete halt prior to turning into any sharp corners, remaining in the same gear both inclining and declining.

Mar 21, 2011

By T Leidich, M Van Zyl, H Lacy

Mining ‘as usual’, until the most recent decades has resulted in limited landform planning and a general lack of mine waste landform design. Material characterisation, mine planning and dedicated professionals undertaking these tasks were rarely available or in place at the majority of mines. This has led to landform instability, erosion, sediment and poor quality water emanating from mine landforms. In many cases rehabilitation and reclamation failed and these sites have ‘landform features’ that are difficult to relinquish or leave and have little or no apparent land use. In many cases mined landscapes around the world have resulted in a less functional and degraded environment, with deleterious impacts on surrounding ecosystems.This situation is now slowly being addressed, as global companies, academics and practitioners and their organisations have started to exploit the ideas from an integration of earth sciences and mining through the application of planning software dedicated to the design of landforms.This development has had its genesis primarily in the United States. We suggest that process has been driven, in recent decades, by the application of resources in response to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), (USA Congress 11 December 1980) and other mine reclamation legislation enacted by federal and states regulators in the USA. The combining impact has seen a huge transfer of capital back from the public purse and ‘potentially responsible parties’, into abandoned mines to affect control, remediation, and reclamation/rehabilitation of those mines.Given this investment in rehabilitation and reclamation, people engaging in the business of landform planning have had the opportunity to address landform reclamation of historic and active sites. The skills of engineers and scientists with improved technology, waste rock characterisation and modelling tools have been combined resulting in the evolution of landform design and in mine planning of active mines. This has delivered cost-effective, sustainable mine closure designs for over 30 years. Integration of mine design with an understanding of geomorphic principals and the natural landscape, coupled with waste and soil characterisation, yield a positive result. Recently work has been applied across large and small-scale projects by companies. As these processes develop, ideas and concepts are evolving that active mines, or mines in the early planning stages, could use to help reduce double handling, and in the long run reduce overall project and closure costs, more effectively attain the desired final land use, and enhance the industry’s reputation and licence to operate.CITATION:Leidich, T,?Lacy, H?and Van?Zyl,?M,?2014. Application of design concepts and engineering controls necessary to deliver well-designed and rehabilitated landforms, in Proceedings Life-of-Mine 2014 , pp 55–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By P Marlow

Raiseboring is an attractive method of constructing shafts, being safe, fast and comparatively cheap. But this means back-reaming through weathered ground. However in the gravels and weathered near-surface rocks typical of the Western Australian goldfields, back reaming large diameter shafts through to the surface is risky and conventional sinking from surface has normally been required.An alternative construction approach has recently been used to stabilise the weak surficial materials and allow raiseboring through to the surface. The method is based on first installing rings of non-contiguous reinforced bored piles around the shaft perimeter, for temporary support, then back reaming shafts at full diameter through to the surface. Immediately after the reaming head is removed, the weak exposed materials are supported using remotely sprayed fibrecrete.The method has been successfully applied to four shafts since July 2007; 3 m and 4 m diameter shafts at Trident Mine, a 3 m diameter shaft at Wattle Dam and a 4.5 m diameter shaft at Athena Mine.Bored pile layout designs have varied from eight to 24 piles, of diameters 120 to 270 mm, in one or two rings. In one case, the top 10 m of the proposed shaft was pregrouted. Subsequent surveys have confirmed that fallout occurred in some shafts, out to the ring of piles, implying that the piles inhibited collapse.The practical implementation of the method was not always easy and many valuable lessons have been learnt. This paper documents key aspects of the method and the critical elements for its application.

Mar 21, 2011

By F Flitti, M Haest, O Dominguez, D Mittrup, G Hird

The automated geology interpretation (AGI) tool has been developed in BHP Billiton to automate stratigraphy logging of drill holes, using any available quantitative data sets. At present, AGI is set-up to utilise geochemistry and mineralogy from infrared spectroscopic data to predict stratigraphy. Once the AGI tool is calibrated, results show that the tool is capable of automatically defining stratigraphy across all of the deposit types, encountered by BHP Billiton Iron Ore in the north-west of Western Australia. Accuracy of AGI at predicting stratigraphy is on average better than 75 per cent, with average accuracies exceeding 85 per cent for some deposit types. The AGI tool can deliver fast, accurate, consistent and objective geological interpretations.AGI is currently being implemented in BHP Billiton Iron Ore Exploration to streamline the drill hole logging process and allow geologists to spend less time defining stratigraphy at the drill hole level and more time investigating stratigraphy in 3D. This will deliver improved geology models, with significant downstream benefits in terms of better resource models, more accurate mine plans, higher plant efficiencies and more consistent ore products, driving productivity in BHP Billiton Iron Ore over the next decade.CITATION:Mittrup, D, Flitti, F, Hird, G, Haest, M and Dominguez, O, 2015. Semi-automated geological interpretation using assay and infrared spectroscopic sensing parameters towards improvements in geological modelling, in Proceedings Iron Ore 2015, pp 313–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M Brockman, M Cowan, A Robeson

"Sunrise Dam Gold Mine (SDGM) is located 820 km from Perth, 220 km from Kalgoorlie—Boulder and 55 km south of Laverton in Western Australia. The SDGM main pit had successfully operated since 1997 and was due to be completed during 2012. An opportunity existed to extract the high-grade crown pillar – 600 kt @ 7 g/t for 135 koz by either open pit or underground methods.The crown pillar was the 60 m (vertically) thick remaining part of the high-grade Cosmo orebody between the top of the paste filled underground mine stopes and the planned base of the final open pit shell.There were two major difficulties being considered when choosing the underground or open pit options:a major wall failure in the upper section of the main pit wall directly above the crown pillar restricting access from the base of the open pit to the top of the crown pillarimpact of a high rainfall event while the crown pillar was being mined from either surface or underground resulting in flooding of the underground mine workings.This paper will discuss the following issues:the process to identify and evaluate the risks in both options using knowledge based modelling software; this technique allowed the evaluation of a complex set of assumptions to arrive at the preferred optionremediation of the Watu failurethe selection of the preferred option and the challenges encountered before, during and after the extraction of the crown pillarthe planning and geotechnical work to ensure the safe extraction of the crown pillarsuccessful outcomes transitioning from open pit operation to a solely underground operation.Citation:Robeson, A, Cowan, M and Brockman, M, 2016. A Case Study on the Assessment, Planning and Extraction of the Crown Pillar at Sunrise Dam Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 115–136 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Billington WG

A structural study of northwest Fergusson Island, part of the D'Entrecasteaux Group, was undertaken using colour and monochrome aerial photography and Landsat imagery. The resulting interpretation shows an upstanding, in part, dome-like metamorphic core complex, which is bound on three sides by an en echelon series of low-angle, thrust faults. Faceted gneissic layers occur throughout the complex. These facets are triangular in plan view and range in size from a few tens of metres, to massive composite zones which traverse the entire uplifted zone, The lower surface of each of the facets are, in fact, low-angle decollements which, during uplift, slid one upon the other to accommodate the vertical and extensional movements. As a consequence, deep structural valleys developed which widen towards the zone of maximum uplift. In many places, recognisable topographic features are replicated on both sides of these valleys, and under the stereoscope can be visually reconstructed to their original pre break-up positions. The southern margin of the core complex is less dome-like and falls away, via a series of deeply-entrenched structural valleys, towards a volcano-studded lowland. The lowland appears to belong to a rift or arm, stemming from the more southerly located Goodenough Bay Infrabasin.

Jan 1, 1987

By J D. Illescas, S N. Arnold, D R. Shaw

Ion exchange (IX) as a primary production technique has been applied commercially since the 1950s; its application in the uranium industry continues to be widespread and is utilised to a lesser degree in the gold industry. The majority of ion exchange applications, outside of gold and uranium, have primarily been for secondary metal recovery and impurity removal. Newer developments in the application of ion exchange, as well as changes in regulatory requirements, are bringing about the wider use of ion exchange as a primary production technique not only for high value metals such as uranium, platinum group metals (PGM), refractory metals and rare earths, but also looking at base metals such as nickel and copper. The ability to build lower-cost, safer, less polluting processing plants with smaller footprints is driving a greater interest in IX, with the main competitors remaining solvent extraction and carbon-in-pulp/leach. This paper discusses a number of areas where IX has been applied and its advantages compared with other techniques.CITATION:Shaw, D R, Arnold, S N and Illescas, J D, 2012. Ion exchange in hydrometallurgy - Secondary metal removal or primary production technique?, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 17-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S Grant, S Emeric, P Baker, E Jones, D Clark

As we strive for a sustainable and resilient future, repurposing assets has become a top priority. In Australia alone, we have a significant number of mineral projects in the pipeline, extensive existing operations, and over 50 000 legacy sites. Collectively, this presents a unique opportunity to be a world leader in mine rehabilitation. Complex stakeholder landscapes, inflexible policies, aged regulatory frameworks, technical uncertainties and increasing liabilities are all barriers hindering effective transition of legacy assets. The impetus for change is further catalysed by shifting consumer preferences, workforces in flux and regional Australians questioning what the transition means for their local community. We need innovative approaches to take a leading role in the industry and support global efforts more broadly. Co-designing an ambitious, shared vision spanning projects, operations and legacy assets with all key parties is a fundamental step to unlock and realise maximum societal, environmental, economic and reputational value. Serious play and gamification can further enhance this visioning process.

Aug 2, 2023

By J Jackson, K Nguyen, A Nguyen, E Manlapig

"With the recent advancement in drill core imaging systems, a large volume of high resolution drill core images can now be rapidly collected and mineralogically classified. This paper introduces a novel semi-automated method for rapid prediction of process engineering parameters from this type of image. The aim is to allow for a rapid and low-cost assessment of the ore processing variability within a mineral deposit with a reduced amount of metallurgical test work. This method will see its application primarily in the project evaluation phase, where proper evaluation of the processing variability of the orebody normally requires a prolonged and costly metallurgical test work program. Applying this image-based texture analysis method on the mineralogical classified drill core images, the ores are classified according to their textures. For each engineering parameter, a small number of physical test work is required to produce a data set for training and testing of the predictive model. The paper also presents a case study in which this method has been applied to predict the A*b parameter used in mineral process plant design.CITATION:Nguyen, A, Jackson, J, Nguyen. K and Manlapig, E, 2016. A New Semi-automated Method to Rapidly Evaluate the Processing Variability of the Orebody, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 145–152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D Zielinski-Nicolson

The emergence of affordable, portable and versatile wireless devices has enabled a new frontier in mine safety equipment. Existing solutions provide methods for tracking personnel and assets in underground mines but are not designed to optimally integrate into existing and emerging systems. Mine management are often required to coordinate primarily independent emergency, personal protective equipment (PPE), tracking and collision avoidance systems from multiple vendors. These systems involve a variety of wireless technologies that require separate integration projects that discourage adopting new services and policies.

May 5, 2022

Investigations of the Mineragraphic Section; Commonwealth Scientific and Industrial Research Organisation, have included most of the known stannite-bearing ores in Australia, and have revealed several new occurrences of this relatively uncommon mineral. They provide information about its paragenesis, and its possible effect on tin recovery, that may be of general interest.Several of the investigations used in the preparation of this paper, were made in the first instance by pr. F. L. Stillwell or in collaboration with him.CASSITERITE-SULPHIDE ORES IN NORTH-WEST- TASMANIA Stannite is a minor component of most of the cassiterite sulphide ores of north-western Tasmania. These include the orebodies of Mount Bischoff, the Cleveland mine, Moina, the Stanley River district, Renison Bell, and the Heemskirk-Zeehan district, and form a well defined metallogenetic provence which is related to the Devonian granites of this part of Tasmania.In these ores mineralisation began. with deposition of cassiterite, a little wolfram, and quartz, topaz and tourmaline. With falling temperature, deposition of cassiterite ceased and arsenopy-rite, pyrite, and especially pyrrhotite, formed in abundance, tending to give massive sulphide ore. A little chalcopyrite; stannite, sphalerite and native bismuth accompanied the pyrrhotite. Deposition of quartz ceased after the pyrrhotite, was formed, and the later-formed nonsulphide gangue consists chiefly of carbonates and fluorite. With, the advent of the carbonates the pyrrhotite was altered to fine-gained intergrowths of marcasite and pyrite. Excess iron from the pyrrhotite entered the intergrown carbonate, or was precipitated as magnetite. Some solution of the cassiterite occurred at this stage, the tin being redeposited chiefly as stimnite replacement rims around the residual cassitellrite grains. Varying, but small, amounts of sphalerite, galena, tetrahedrite and silver minerals were depoSited at this stage, bringing the mineralisation to a...

Jan 1, 1951

By D Chalmers, C C. Harb

The detection and control of gas levels in mining is a continuing challenge for the industry. Standard detectors have many problems that could be overcome with laser based spectroscopic instruments, but to date these systems have not been suitable for mining conditions. This paper reports the development of a new digital data extraction scheme to modernise traditional cavity ring down spectroscopy (CRDS). CRDS is a direct cavity enhanced laser based absorption technique, which is used to allow the identification of an unknown substance by their molecular fingerprint; this unknown substance is identified by analysing the ring downtime of the light exiting the optical cavity. Traditional CRDS has many issues when analysing substances in hostile environments, or when multiple species may be present. This presents an alternative approach, called real-time CRDS (rtCRDS) that has the potential to overcome many of these issues and produces systems that could be used in the mining industry. The system utilises newly developed widely tuning quantum cascade lasers combined with improved optical cavities and novel digital data extraction to produce spectra over a 1500 nm range in a few seconds. The ring downtime measurements produced are accurate and have high sensitivity and maximum signal to noise ratio. This paper discusses the technique, illustrating the advantages compared to traditional systems and show real-time spectra for a set of molecules of interest to the mining industry. This paper also provided an analogy between this approach and that used in digital communications systems, and shows that this scheme is ideally suited to provide a network of sensors in hostile environments.CITATION:Harb, C C and Chalmers, D, 2015. Real-time methane detection – modern digital laser spectroscopy for hostile environments, in Proceedings The Australian Mine Ventilation Conference, pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Sloan GJ, Lysnar RD

Since the of Bergstrand's Geo-dimeter in 1946, and Wadley's Tellurometer in 1956, there have been numerous Electromagnetic Distance Measurement (EDM) instruments produced throughout the world by a variety of companies.This form of measurement has not merely replaced other methods of measurement, but has caused considerable change of emphasis in survey techniques. Major control surveys are now being accomplished using trilateration instead of triangulation. The surveying of open cuts or engineering work may be done in a fraction of the time and, in the majority of cases, to a greater degree of accuracy than with older methods.It is surprising that with this new tech-nology and development of EDM equipment which is compact, easy to use and no longer so expen-sive, no advance has been made in underground surveying. If we look at equipment being used by the majority of mining companies, we see that there have been very few changes since the Second World War. Very little research has been carried out to enable the surveyor to do his work more easily in conditions which, at the very least. are hazardous.

Jan 1, 1984

By J-P Franzidis, M Esvelt, E V. Manla

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant that is able to treat up to 2 tph solids. It consists of a bank of six 130 L WEMCO« SmartCells« and a bank of six 50 L WEMCO« SmartCells«. It was developed as part of the AMIRA P9 Project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. However, it may also be used to carry out pilot-scale flotation test work. This paper briefly describes the circuit modelling, simulation and scale-up test work performed using the FCTR and the use of the FCTR in pilot-plant test work performed by the metallurgical staff at WMCÆs Kambalda Nickel Operations and Mount Keith Nickel Operation. At both Kambalda and Mount Keith the FCTR was found to be very flexible and straightforward to run, with an easily changeable circuit configuration and stable operation. Testwork was facilitated through having full stream sampling on all streams, and a high degree of instrumentation providing accurate measurement of process variables. The results obtained from the FCTR testwork were highly repeatable. As a consequence of using the FCTR, WMCÆs Kambalda Operation and Mt Keith Operation were able to complete a rigorous programme of pilot plant testwork more quickly than in the past, and with a high degree of confidence in the results.

Jan 1, 2003

By A Murphy

Mining plants and infrastructure, and the decisions made by their designers, can have large impacts on their environmental and social context, commonly referred to as the site or plant footprint. They can also be the source of constructive contributions to sustainable development when designers are enabled via the information, systems and tools to incorporate sustainability in engineering processes. A facility’s footprint and the project’s contribution to sustainability – economic, environmental and social aspects – are now key considerations in regulatory approval processes and are the fundamental drivers of support, or opposition, from the project’s stakeholders.Historically, plant and infrastructure designers have not been well integrated with the environmental and social professionals who are engaged to pursue regulatory approvals. Despite this, many objectives central to technical and process engineering have in fact contributed positively to a facility’s footprint and indeed its contribution to sustainable development. Examples of these objectives include increasing process and energy efficiency, and minimising the quantities of waste requiring disposal. With the framework of sustainability, mining plant and infrastructure designers are indeed at the forefront of incorporating sustainability into resource industry projects and are central to the process of obtaining regulatory approvals and ongoing stakeholder support. The process of incorporation starts with a shared understanding of sustainability and sustainable development, and continues with project processes that facilitate information and knowledge exchange throughout the project life cycle.CITATION:Murphy, A, 2014. Incorporating sustainability into mining plant and infrastructure design, in Proceedings Life-of-Mine 2014 , pp 637–646 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By F Butler, G E. Batley, A C. Hogan, A R. Butler

The ANZECC/ARMCANZ (2000) Water Quality Guidelines (the Guidelines) are the primary reference used in Australia and New Zealand for managing and regulating water quality. For most mining operations in Queensland, the environmental authority (EA – licence) incorporates the national default guideline values (GVs) for ecosystem protection as trigger levels (TLs). Exceedances of TLs ‘trigger’ further investigation and reporting. A review of the surface water compliance history at a metalliferous mine in North West Queensland identified minor exceedances of the cobalt GV as a common trigger for investigation and compliance reporting.The reliability of GVs is dependent on the availability and quality of ecotoxicology data for the relevant contaminant. The current national default GV for cobalt of 1.4 µg/L is classified as a low reliability GV due to the lack of available data at the time it was derived (ANZECC/ARMCANZ, 2000).The Guidelines are presently being revised and the toxicant GVs will be available as a set of web-based values and associated technical briefs. The new platform will enable the timely revision of existing GVs and inclusion of GVs for additional toxicants. Cobalt was considered a priority toxicant for the Guidelines’ revision, but was not included in the revision process.A preliminary review of the international literature indicated that at least 15 additional chronic cobalt toxicity studies had been published since 2000, sufficient to derive a high reliability cobalt GV using the protocols developed for the revision of the Guidelines (Batley et al, 2014; Warne et al, 2015). This presented an opportunity to improve environmental management by increasing the reliability of the performance measure.CITATION:Hogan, A C, Butler, A R, Butler, F and Batley, G E, 2016. Derivation of high reliability water quality guideline values for cobalt in freshwaters – improving water quality guidelines for better water quality compliance management in mining, in Proceedings Life-of-Mine 2016 Conference , pp 205–208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Umar N

Traditional exploration has been undertaken by both local and overseas experts to discover tin deposits in Indonesia over almost 300 years. Indonesia is part of a tin belt which runs from Myanmar in the north through Malaysia to Singkep, Bangka, and Belitung islands in Indonesia in the south. The discovery of alluvial tin deposits is becoming harder as the more obvious geological targets are exhausted and topographical conditions become more difficult. New approaches are required to sustain successful exploration. There are indications that tin deposits can be found at depth on-shore as well as off-shore. These deposits are found associated with tough clays. On-shore tin exploration is hampered by swampy areas, while the off-shore search is often affected by difficult sea conditions. These factors lead to increases in the cost of exploration as well as the cost of subsequent production. Tin price fluctuations and environmental issues are also of major concern in the planning of the future operation of tin mining in Indonesia.

Jan 1, 1996

By N M. Player, R P. Varden, E Jones

"An effective geotechnical design provides an accurate and appropriate assessment, balanced with a mining company’s risk profile. Justifying the cost of slope assessment requires an understanding of the input sensitivities, and resultant risk, to achieve a slope of a required functionality. As a project progresses from Scoping to Feasibility, the geotechnical risk becomes better resolved through increased expenditure on drilling, testing, analysis and modelling as long as the input data is appropriately spatially distributed. Providing accurate and appropriate geotechnical assessments in the early stages provides confidence in all following stages, especially where initial analysis indicates difficult geotechnical conditions. It is also in the early stages of project definition that there is most opportunity to maximise the value of the deposit through investigations into optimal mining methods.This paper examines the advantages of geotechnical engineering input through a project study period. Early geotechnical involvement allows the Scoping and Pre-Feasibility Studies to be more effective. Operational risks can then be better understood and dealt within the Feasibility Study phase, also ensuring that the correct risks and management controls are put in place.With commodity price pressure and cost of resource recovery in a downturned industry, reducing the risk to cash flow, resource recovery and safety should be a primary goal for all mining companies. Reduced risk can be effectively achieved through geotechnical design of slopes to achieve a required performance as part of an integrated study to the Reserve definition and mine design.Citation:Varden, R P, Player, J R, Player, N M and Jones, E, 2016. Justifying Slope Design Risks and Costs, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 185–201 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By P Gleeson, J Coombes, P Suresh, T McLennan

The last 20 years have seen a dramatic rise in the use of 3D visualisation and modelling for geological data, but there has been relatively little effort to do the same for the variogram models that underpin the standard estimation algorithms used by the mining industry.For kriging, one of the most used geostatistical estimation methods, specifying a variogram model is a critical part of the modelling process. Experimental variography is the primary method for approximating the theoretical variogram function from the available sample data, and then determining an appropriate variogram model from the approximations.The traditional tools used for experimental variography are limited to looking at subsets of the data and are often presented without reference to geographic space and geology. It can be difficult to know what input data is being used for a particular experimental variogram, and whether there is enough support in the experimental variograms to propose an appropriate model.To overcome these limitations, an innovative approach called situational variography has been proposed that visualises variograms in 3D alongside contextual geological and geometric data. Presenting variograms in this manner aids understanding of how the spatial variance relates to the underlying data.A 3D extension of the 2D radial variogram maps will be investigated which allows for dynamic exploration of the full experimental variogram cloud. These 3D experimental variograms are much easier to visualise situationally.A workflow for situational variography will be outlined and the advantages of the situational approach will be illustrated using a porphyry copper deposit.CITATION:Gleeson, P, McLennan, T, Suresh, P and Coombes, J, 2017. Situational 3D variography – determining the variogram in the context of geology, in Proceedings Tenth International Mining Geology Conference 2017, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By S Russell

The completion of the $1.1 B Cape Lambert Upgrade project is the second ‘pillar’ in Rio Tinto Iron Ore’s expansion program that has enabled Rio Tinto Iron Ore to effectively double iron ore shipping capacity from the Pilbara between 2003 and 2009 to 220 million tonnes per annum (Mt/a), following the successful completion of the Dampier Port upgrade project two years earlier.The Cape Lambert Upgrade has built on and enhanced many of the engineering achievements of the Dampier Port upgrade project, as well as developing innovative and unique engineering solutions for this complex ‘brownfields’ project that presented its own challenges, particularly in this distinctive open-water port environment.The project was implemented in two phases to achieve an increase in port shipping capacity from 55 to 80 Mt/a – an enhancement phase and an expansion phase.The initial enhancement phase, which provided an increase to shipping capacity from 55 to 60 Mt/a, focused on increasing the utilisation and effi ciency of existing plant and equipment with a relatively small capital expenditure.The expansion phase, which provided the increase in shipping capacity to 80 Mt/a, included extending the existing iron ore wharf by 256 m to create four shipping berths, a new shiploader, an expanded stockyard (including a new fourth bucket wheel reclaimer) and a new surge bin facility to maximise outloading tonnage rates.The Cape Lambert Upgrade project was implemented whilst the port remained fully operational and continued to ship record tonnages of iron ore throughout the project duration. This achievement required signifi cant upfront planning and sequencing of construction activities to support the operation of the port. Innovative design and construction techniques were used to mitigate the impact and enable construction activities in and around the operating plant.Throughout the project, new benchmarks in engineering design and construction practices were established, which have since been adopted for new iron ore port facilities currently in planning phases.

Jul 11, 2011