Search Documents

By Manlapig E. V

ABSTRACT- I Results are given for a series of tests in which a 300 mm pilot-scale Jameson cell has been used in copper recleaner flotation, and for the flotation of a lead rougher feed. the results indicate that the production rate of solids, at the same superficial air velocity Jg, is higher than in conventional columns. Thus in the copper recleaner application, the pulling rate reached 14 gm/cm2/min compared with between two and three for an operating column, while in the lead cleaner application the comparable figures were 12 - 14 gm/cm2/min for the Jameson cell vs 8 - 9 gm/cm2/min for a test column. A froth crowder was used to increase the air superficial velocity Jg in the Jameson cell in the copper recleaner, while holding the collection mechanism and pulp feed rates constant. The recovery increased from 50 per cent to over 90 per cent, suggesting that recovery is controlled mainly by the froth conditions, rather than the particle-bubble interactions in the Downcomer.

Jan 1, 1991

By A K. Bayer

When the human eye fails in the evaluation of quality parameters in the extraction of minerals the use of laser-induced fluorescence analysis (LIF) can supply more detailed information on the composition of rocks. On the basis of measurements of selected raw materials engineering concepts for the use of this method in the mining industry as an innovative system for horizon control of mining machines will be described and the most important analysis parameters, influencing factors and interference variables are presented.

Jan 1, 2003

By B, T Norgate, S Sanetsis, R Davidson

Global cement production accounts for about five per cent of man-made CO2 emissions (WBCSD, 2002). Such operating practices will increasingly be considered unsustainable, unless significant reductions in environmental impact can be realised by the industry.Slag is a high volume waste product from ironmaking, with about 300 kg of slag being produced per ton of iron. Critically, one ton of slag waste, if used as a replacement feedstock for Ordinary Portland cement (OPC), can prevent around one ton of emitted CO2 since no calcining is required. Slag cement blends can also show superior properties compared to OPC, such as lower heats of hydration and higher late strengths, but more development is needed to overcome their low early strengths. Rapid quenching of molten slag is required to produce æhydraulically-activeÆ binder when reacting with OPC; but water quenching can also require between five to ten tons of water per ton of slag at the plant. æDryÆ granulation (atomisation) is emerging as an alternative technology, the resulting solid product does not require drying, and possibilities exist for recovering heat energy from the hot slag.CSIRO Minerals has well-developed skills and equipment in pilot-scale pyrometallurgical treatment, and granulation of molten slag, including traditional wet, and also dry methods. Techno-economic desktop studies can also be used to help quantify factors such as value-adding of treated waste products, potential reductions in CO2 emissions and carbon credits, reductions in water consumption, and the possible decreased energy costs associated with fine grinding of dry slag granulate.The authors will present preliminary results from slag atomisation/dry granulation testwork (0.5 - 2.5 kg scale) and associated modelling studies, conducted using a æsyntheticÆ and industrial ironmaking slag. Outcomes from a techno-economic study on production of cement utilising wet or dry atomised slag granulate will also be discussed in detail.

Jan 1, 2004

By Van Hoorn PD

For the development of BHP's Gregory open cut coal mine in Central Queensland a mini computer was successfully used to assist staff in the evaluation of the deposit and the planning of the mine. The Gregory deposit is essentially a single mineable seam deposit, however the systems developed may be applied to other coal deposits including multi seam occurences. The first phase of the Gregory computer evaluation and planning project involved the establishment of a borehole data base for the storage, retrieval and analysis of both strata and quality data. During the second phase a numeric block model of the coal deposit was created. Using this model reserve calculations were carried out by specifying the area with the aid of a digitizing tablet. The third phase involved the develop- ment of systems to simulate the dragline stripping operations including the rehandle percentage calculation, a dragline production schedule showing coal quantity and quality exposed, and a combined multi dragline operation schedule that can produce figures and graphs for up to 20 variables. A derivative of the operating plan was a programme that gave productioh cost estimates

Jan 1, 1978

City Resources Limited selected Vanuatu as a target area for epithermal gold mineralization because of its relatively unexplored character and its location on the southwest Pacific rim. During 1985 a systematic program of reconnaissance prospecting was completed on six islands within the Vanuatu group, using a helicopter and a specially designed exploration support vessel with on-board assay laboratory. Within a period of 4 months, reconnaissance prospecting of all six islands was completed, two previously unknown epithermal gold provinces had been discovered, and six major prospects warranting detailed exploration had been identified. Factors which contributed to the success of the program include (i) a flexible management approach, (ii) the mobility and access provided by the support vessel/helicopter combination, (iii) rapid assay turn-around, and (iv) adherence to basic prospecting techniques. The relative merits of various sampling media are discussed.

Jan 1, 1987

By Ryan A, Dennis R, Dekker D, Ellis W, Sowerby B

An automated facility for non-destructive elemental analysis of mine samples has been developed and tested at Mount Isa in association with the CSIRO. The analysis is based on the prompt and delayed measurement of gamma radiation emitted by the sample during and after separate fast and thermal neutron irradiation. No sub-sampling or sample preparation is required and the analyser is operated by one person that would otherwise be splitting drill core in preparation for conventional analysis. The analyser has been calibrated to measure the following (precision in parenthesis): Ag (14 ppm), Pb (0.5 wt%), Zn (0.5 wt%), Cu (0.04 wt%), Fe (0.7 wt%), S (1.1 wt%), SiO2 (0.8 wt%), A1203 (0.07 wt%), Mn (0.05 wt%), specific gravity (0.02 g cmt). Crushed or whole drill core samples that range in size between 0.5 m and 1.8 m of equivalent BQ size drill core can be analysed at a rate of six samples per hour. If required, drill core samples can be re-packed in their original configuration for storage following analysis. Standard samples are measured every day to ensure operational stability. The analyser is controlled by a personal computer which prints the results and stores them along with the raw data on the computer hard disk. This paper reports the performance of the analyser during 1992 for routine analysis of drill core from the lead ore bodies of both Mount Isa and Hilton mines.

Jan 1, 1993

Tumbling mills have been used in the minerals indusu) for occr WO years, with the design changing little, but the size of the individual pieces of equipment increasing significantly with the lowering of head grades, and the push for greater

Jan 1, 1997

This paper briefly reviews the background of mobile primary crushers and their current main areas of application. The benefits of applying mobile primary crushing and belt conveying systems are analysed. The impacts of applying such systems to different steps of the mine process are discussed, including mine development and planning. Application examples are used for demonstrating further possibilities to apply mobile primary crushing and belt conveying systems in mining projects successfully.

Jan 1, 2007

By P Warner

Mines are often located in remote areas that are not well served by æstiffÆ power grids. Radial transmission networks, high lightning incidence (eg in South Africa the Witwatersrand experiences seven to ten strikes/km2 per year), low short circuit strengths and diesel generation are not uncommon. All these factors result in the electric power supply to many mines being unusually prone to dips and disturbances. æLegacyÆ winder drives û cyclo converters and dc drives û convert power directly from the supply to the motor, with no intermediate energy storage element. Further, they rely on the supply network for commutation and are therefore sensitive to supply voltage disturbances. There is a high probability that a dc or cyclo mine winder will trip during a supply disturbance, often resulting in lost production time and call-outs for technical staff to reset or even repair equipment. In contrast, a voltage source inverter (VSI) ac drive stores a large quantity of energy (in the dc link capacitors) and is fully self-commutating. Hence, this topology is inherently more immune to supply voltage disturbances. Indeed, vendors of ac VSI mine winders make general statements about the superior performance of their drives during supply disturbances. However, the advantages have apparently not been previously quantified. This paper compares different winder drive topologies and their sensitivity to supply disturbances, considers categories of supply disturbances and quantifies the cost of the effects on the different drive types.

Jan 1, 2005

In October 2005 Phelps Dodge mining, a US based company, visited several Australian mining companies and mine sites to ascertain the current applications of risk management methods in the organisation. The results of this review, documented by the author, indicated a ælayeredÆ approach from high level site or major hazard analysis through to face level, æstop and lookÆ, methods. The approaches of several companies were summarised in one simple layered model. This model is helpful to other sites and companies to identify potential improvements but also offers an image of best practice that may assist with the governance of OH&S by both company boards and community regulators. The issue is particularly relevant as we discuss national consistency in mining regulation. This paper examines the layered model, the company and site approaches that helped define the model, as well as the suggested implications of the layered model to governance.

Jan 1, 2006

By Mostyn G. R

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

Arrow Energy NL has been operating a number of coal seam gas wells in the Darling Downs region of Queensland. At the time of writing this paper, the region is enduring an extended drought period. The local aquifers are depleting and have not been significantly recharged in over a decade. The local communities (both rural and townships) are struggling to obtain water. Currently, coal seam gas (CSG) operators (under licence) draw water from the coal seams as part of the gas production process and the majority of operators choose to evaporate this water, as it is characteristically brackish to saline in quality and as such must be contained. Although the water produced from one CSG operator is not sufficient to drought-proof the greater area of the Darling Downs, there is potential to supply smaller local areas and contribute to the sustainability of these communities. This paper outlines the work completed by Arrow and its local community partners on the Darling Downs to date, and discusses the application of the produced formation water for:stock watering in feedlots, as a feedstock for coal washing, as a potable water supply for Dalby, as an agricultural water supply for cotton farming, and use as a medium for growing salt-water fin fish.

Jan 1, 2006

By Hempenstall J, English W

Mine management has a responsibility under the various acts of state parliaments for the adequate ventilation of existing workings. It also has a need to plan adequately for the ventilation of proposed workings. Future workings alternatives have become progressively more complex and ventilation planning of the various possibilities must be undertaken within an atmosphere of rapidly changing market circumstances, etc. Any non-optimal solution will prove more expensive than necessary on both capital and cost bases. Clearly these increasing and alternative ventilation demands of coal mines in Australia have multiplied the work load of ventilation engineers. Management in general has for some time been aware of the advantages of using computers for commercial applications such as payroll and stores inventory. However, while the hand held calculator has replaced the traditional log tables and slide rules for smaller engineering calculations, the larger digital computer has not made the same

Jan 1, 1983

Traditional methods for the production of transition metals from their ores usually include the electric arc smelting of the ore or concentrate to produce a ferroalloy. This is subsequently refined to produce either a ferroalloy or to produce the metal or metallic carbide. Recent trends in the treatment of iron ores have seen the development of many processes for solid state carbothermic reduction followed by melting of the prereduced iron to produce steel and similar types of processes are under consideration for the production of ferroalloys. There are clear potential savings in energy and control of emissions from such processes. This paper discusses some research which is currently underway at La Trobe University into the solid state carbothermic reduction of chromium and tungsten ores to produce the metallic ferroalloy or the carbide for subsequent further processing. The kinetics of the carbothermic reduction of both chromite and scheelite were found to be dominated by gaseous CO rather than by direct carbon reduction. However the diffusion of carbon into the ore is certainly an important feature of the process. The production of tungsten carbide from the metal is the slow step in tungsten reduction. The development of phases during reduction were studied using a scanning electron microscope and an electron probe and knowledge of the phases produced allows analysis of the reduction process.

Jan 1, 1997

The design and operating characteristics of the hydraulic cyclone elutriator were described in detail by Kelsall and McAdam (1963), and the method of operation of the commercially available version, the Cyclosizer, is described in the manufacturer's pamphlet (Anon). Complete details of the operating procedure are given in the relevant operating manual (Anon, 1964).The cyclones which form the basis of the Cyclosizer (Fig. 1) under normal operating conditions produce typical cut sizes of 44, 33, 23, 15, and 10 µm for cyclones one to five respectively for material with a specific gravity of 2·7. At the end of the selected elutriation period each sized fraction is discharged and collected for subsequent assay or analysis but all material rejected by the fifth cyclone (e.g. minus 10 \lm quartz) normally passes to waste. When this material is needed for separate study, although its amount and average analyses can be calculated by difference, it may be necessary to collect more than 250 I. of very dilute suspension, flocculate the solids, allow to settle, and decant off the supernatant liquid.This procedure is cumbersome and inconvenient and the simple technique to be described may offer some advantages. The temperature of the water fed to the Cyclosizer is maintained at a constant value for added reproducibility.PROCEDUREThe present overall treatment of the subsieve material (minus 37 \lm) fed to the Cyclosizer incorporated several refinements compared with normal operation and these may be best illustrated by anactual example. Material to be cyclosized (25 to 100 g depending on size distributIOn and specific gravity) is completely dispersed in water at 23 QC by vigorous stirrmg, using suitable dispersants if necessary, in a...

Jan 1, 1974

The theme i wish to develop in this talk is how we might make use of the scientific and technological knowledge we now have ofextraction metallurgy to meet the present-day needs of the production industry.Before doing so, I would like to say a few words in tribute to Dr. G.K. Williams since he was a past master at precisely what I wish to talk about. I knew G.K., as everybody called him, during the time he spent at Avonmouth in the late 40's and in the 50's. Later, when he was ostensibly retired, I had the pleasure several times of lunching with him when I was visiting Melbourne.When G.K. was at Avonmouth, the Imperial Smelting Process was in that capricious adolescent stage in between the pilot plant and the full-scale commercial unit. G.K. was a great collector of process plant data which hung in cascades from the walls of his office and-from his hand-operated desk calculator. What G.K. understood very well were the basic metallurgical and engineering principles of what was going on in the sinter machine, the shaft furnace and all their ancillaries.

Jan 1, 1985

It is hypothesised that increasing the number of loading passes will produce a reduced range of truck payload outcomes compared with four-pass loading. The paper provides analysis to support this hypothesis. It is shown that, hypothetically, loading trucks with five or more passes will result in reduced tendency for overloading and reduced confidence interval for truck payloads that increase the confidence level of containing high end payloads within safe and commercially acceptable limits. Furthermore, increased number of passes provides for more precise bucket load spotting and so improves distribution of payloads within truck bodies. Truck-loading issues examined by the paper include: Improvement in life of driveline components and tyres. Generally tyre costs are relatively moderate; but tyres tend to become an increasingly sensitive performance/cost component as truck scale increases; Reduction of site severity fects flowing on to suspensions, truck frames and structural components generally with potential for reduced long-term repair costs; Less physical body damage due to smaller load increments; Reduced risk of non-compliance with payload limitations for safe braking standards; Increase in loading cycle times tend to increase with scale of loading machinery within the limits of a specific type of equipment (ie rope shovels or hydraulic shovels). Production increase with increased bucket capacity is, to a degree, offset by slower loading cycle times. This is particularly pronounced with front-end loaders but tends to be less noticeable with hydraulic excavators/shovels and electric rope shovels. Decrease in loading time, as a proportion of total truck-cycle time as open pits deepen and dump reaches increase. The production and cost benefits of four-pass loading tend to diminish as truck cycle times increase. The paper also discusses the implications for loading-equipment philosophy to satisfy the future needs of the industry. Cost benefits from upscaling tend to diminish as truck scale increases, so increasing management diligence and close monitoring are required to ensure that expected outcomes are realised. These truck-loading issues have been researched to assess the benefits positive or negative) of four-pass loading in practical scenarios. An attempt is made to determine whether four-pass loading is a æmust-haveÆ or merely a æmythÆ.

Jan 1, 2003

By S M. W Rajaratnam, P Varma, T L. Sletten

Mining employees undertaking shift work are at considerable risk of experiencing sleep disturbances and circadian rhythm disruptions. In the complex, high-risk environment of mining, these sleep and circadian disruptions lead to adverse impacts on employee health, alertness and safety. Evidence-based tools that effectively target improvements in sleep health amongst shift workers are needed. Variability in work hours and individual differences in the response to shift work mean that a ‘one-size-fits-all’ solution is often insufficient in complex work environments. Currently no interventions provide tailored support for shift workers based on their rosters, personal commitments and sleep habits. Existing technologies, such as smartphone applications and watches, allow sleep monitoring, but their strategies are targeted towards night sleepers, which does not translate to shift work contexts. To address this, our team has developed an innovative digital tool that implements biomathematical models to provide automated, personalised sleep and circadian intervention strategies to optimise sleep, alertness and performance during shift work. The tool uses mathematical models of sleep and alertness regulation that provide physiologically optimal times for an individual to sleep when experiencing circadian disruption. This program of work included co-designed development of a world-first app with shift workers and the examination of the preliminary efficacy of the intervention for improving sleep, alertness and performance.

Apr 16, 2024

By T Vizcarra, G Sandoval, C L. Evans

One of the challenges in the development of mineral processing simulators is modelling the liberation characteristics of particles produced by comminution circuits. Understanding the mineral characteristics of these particles is one of the keys to predicting their behaviour in separation circuits. While more fundamental research seeks to model the non-random breakage of ores this work examines whether we can move forward now by using observed characteristics of ores to model the composition of particles generated in comminution processes. Several researchers have noted the similarity of the liberation characteristics for a selected size fraction of particulate material, whether the fraction comes from a coarse material, such as the product from a jaw crusher, or a more finely ground material, such as the product from a ball mill. In most cases these observations were reported as an aside and were not the main focus of the published work. This observed behaviour has the potential to be a useful tool for modelling the particle characteristics in mineral comminution and separation circuits, particularly as we move towards the development of multi-component models. However, before the behaviour can be used widely we need to understand which ore types follow the observed pattern and which do not. The current work examines a range of ores and identifies which exhibit the pattern of similarity of composition for particles in a given size class that has been produced as the result of a variety of breakage conditions. The impact of mineralogy and texture on the evolution of liberation characteristics for both valuable and gangue minerals is discussed.

Jan 1, 2008

By Koeng R, Richardson M, Hoare R

A discrete event computer simulation model was developed for two of the stoping methods currently used at the Z.C. Mines Broken Hill oper- ations. The objective in undertaking this project was to provide an effective tool for mine planning and design to allow comparisons of alternative extraction strategies and attempt to optimise the allocation of capital equipment and human resources. The Slam II simulation program was used in conjunction with ,a com- monly used data editor, text editor and graphics package to allow the simulation to be done on a personal computer with minimum training requirements. The computer hardware used was a portable computer cur- rently available using 80386/20MHz electronics. Specific logic techniques were developed to allow the Slam II language to simulate mining opera- tions because it was originally developed for manufacturing and com- mercial simulations. The design of the model was based on observations and a data collec- tion campaign. The model was designed with flexibility which allows simple editing of the input data which includes: - Insitu volumes - Development statistics -Loadout efficiencies -Loader speeds, availabilities and capacities -Chute numbers, volumes, distances and blockage statistics -Trucking statistics -Work schedules -Utility statistics

Jan 1, 1988