Search Documents

By S Q. Zhao, J H. Wei

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Xitieshan lead-zinc deposit is located in the north margin of the Qaidam Basin, Qinghai Province, China. It is one of the largest massive sulfide deposits in China and is supposed to be of the sedimentation-exhalation (SEDEX) type. Based on the main ore mineral and sulfur isotopic compositions in sulfides found in the wall rock, the S of the deposit is considered to originate from the mantle, but the fluid potentially mixed with sea water during the hydrothermal circulation exchange. The study of lead isotopes shows that the metallogenic material is characterised by the mixture of orogenic and upper crust sources. The lead isotopic signature of the wall rock is similar to that of the ore, which shows synsedimentary characteristics. According to the composition of the rubidium and strontium isotopic signature, the value of 87Sr/86Sr is lower than the average value of that in the crustal rock, which is larger than that of the mantle. Hence, the metallogenic materials of this deposit mainly originate from the crust, which is related to materials of volcanic rocks activation and migration of the deep hot circulating water. The process of the metallogenic fluid circulation shows continuous interaction with crustal material and lead to continuous enrichment of the ore forming fluids. From the study of the fluid inclusion microthermometry of the ore and the associated minerals combined with the C, H-O, Si isotopes, it is believed that the metallogenic fluid is mainly coming from the mantle or the deep magma chambers. The rising deep fluid then mixes with the sea water. The carbon dioxide escaping and mixing with sea water during the hydrothermal exhalation process leads to the rapid precipitation of the hydrothermal fluid to deposit metal. That is proposed as the principal formation mechanism of the Xitieshan deposit. Further studies are proposed, including obtaining geochronology data from this deposit.CITATION:Zhao, Z X, Wei, J H, Liang, S N and Zhao, S Q, 2015. Advances in research on metallogenic mechanisms for the Xitieshan sedimentation-exhalation lead-zinc deposit, Qinghai Province, China, in Proceedings PACRIM 2015 Congress, pp 487–494 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Dunbavan M, Mallett C. W

The sequence of development and back analysis of the failure of a spoil pile in the 1B pit of the Moura Mine are given. The mode of failure was a two-wedge mechanism with a basal slip plane passing through a clay band about 2 m below the pit floor. Remedial actions for improving spoil pile stability are discussed.

Jan 1, 1981

By Fabjanczyk MW, Aziz NI, Hii J

The paper presents the results of a series of pull out tests performed on roof reinforcement systems currently being adopted in mines in Australia 7mm wire, dividag bar, 15.2mm strand cable, and birdcage cable. The study also investigated the load deformation chara- cteristics and the various design parameters controlling the effectiveness of a cable-grout system. Suggestions for continued work are Highlighted.

Jan 1, 1986

By Hughson B

At present sane man-made Improvements and natural features are constraints on unlimited underground mining. 7 hey will continue to remain, as constraints on the future high production mining systems as wall. Unless these constraints are overacTe by research, where possible, future high production systems may became unacceptable. 7 he areas of future research include improved subsidence prediction techniques applicable to future mining systems, subsurface subsidence behaviour, mining systems capable of producing no surface subsidence and subsidence damage assessment.

Jan 1, 1988

By T M. Campos, J Silva, L M. Tavares, J Lichter, L P. Alves, B K. N Rocha, H D. G Turrer

The depletion of the richest ore deposits and the increase in number of mining projects involving deposits with complex mineralogy, higher competence and lower grade has led to an eminent need for improving understanding on multicomponent behaviour in mineral processing. One particularly relevant case is the ball milling of itabirite iron ores fed to the processing plant of Minas-Rio operation in Brazil. Dealing with the two main mineralogical components of the ore, namely hematite and quartz, the operation faces some challenges to improve understanding on how the two components behave in the process. Mathematical models have showed potential to give support in this task, but its applications to describe this type of industrial-scale grinding is still missing. The present work demonstrates the application of a multi-component ball mill model to simulate a closed ball mill circuit with hydrocyclones using the commercial software Integrated Extraction Simulator (IES). Model was calibrated on the basis of bench-scale tests and industrial surveys. Multi-component simulation results are then compared to those considering a single component in the feed, demonstrating the value and great insights that can be achieved by using the former in optimising plant operation.

Aug 24, 2022

By Jones KW, McClelland RA, Denholm WT, Taylor RN, OÆShea J

Associated Tin Smelters, Sydney, are developing tin smelting operations in a prototype commercial SIROSMELT plant comprising two furnaces of 5 to 8 tonnes capacity. Features of the plant and its operation are discussed and results of its application to tin slag reduction and high-grade tin concentrate smelting are presented. Development work is still in progress but experience indicates that the technology has potential for lowering the costs of tin smelting and relieving constraints on grade and iron content of concentrate imposed by conventional technology.

Jan 1, 1984

By S K. Schwank

Trench cutter systems have been used in civil engineering for the least 30 years for the installation of deep cut-off walls, retaining walls and foundation systems. The systems are constantly advanced to achieve greater depth, penetrate through harder rocks a provide a bigger footprint of the cutter. The state-of-the-art equipment can reach down to 250 m vertical depth and penetrate all different types of soils and rocks up to 150 MPa unconfined compressive strength.In mining, especially in commodities with a high value and where the ore deposit has a small footprint, cutter mining with vertical attack from the existing ground level will be a new, cost-efficient approach where conventional open pit mining is not economically feasible due to a high stripping ratio. The same applies for open pit mines that have reached the end of their conventional mine life and where going underground is also uneconomical. The BAUER Cutter Mining System, which has been adapted to the special needs of mining, is a new technology that will allow mining at depths of up to 250 m.The same system can be also applied to ore dykes, be it vertical or slightly inclined, concentrating the excavation on the actual orebody and minimising the strip ratio and the contamination of ore. The system can be adapted to the dimension of the dykes or veins and to the rock conditions.BAUER’s latest approach is to use the vertical cutter mining technology for the extraction of sea floor massive sulfides from the seabed in deep ocean waters. Due to the compact footprint of the system and the vertical attack for mining, extraction of the ore can be concentrated on the hot spots, minimising the environmental impact on the sea floor both for mining and manoeuvring the remote-controlled mining tool.CITATION:Schwank, S K, 2015. Cutter mining – crossover technology from civil engineering to mining, in Proceedings Third International Future Mining Conference, pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

In the first half of 1987 two four metre diameter raise bore holes were drilled at the Olympic Dam Project for ventilation purposes. The first hole, 476 m x 4.0 m diameter was completed in 96 days, 35 days longer than scheduled. The second hole, 407 m x 4.0 m diameter was completed in 39 days, 2 days ahead of schedule. Both holes were drilled with a Robbins 121R rig using a Wirth head that consisted of 23 face cutters and 5 side cutters, supplied by a contractor. After the sites were located a grouting program was carried out to help seal off an aquifer between 160 and 180 m below the surface. Cavities discovered in the Andamooka Limestone were filled with concrete. Because of the overlying dune sands and clay both sites were pre-sunk to the competent Andamooka Limestone.

Jan 1, 1988

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022

By Raymond G. F

Geostatistics - a tool used by geologists and mine planning engineers to estimate grades and rapidly evaluate alternative mining strategies has reached an advanced stage of development for the silver-lead-zinc orebodies at Isa and Hilton Mines. Geostatistics has been used for over a decade in the massive copper orebodies but the stratiform lead-zinc orebodies are much more complex and provided a completely different set of challenges. Recent increases in computer processing speed and power provided by the Integrated Mine Planning System (IMPS) has aided the development of the geostatistics package. Also the formation of a project team and the subsequent in-house development which has drawn together the expertise of geologists, engineers and system analysts has contributed significantly to the success of the project.The most important feature of any approach to modelling the lead-zinc orebodies is that the kriging search must consider estimate and sample points according to their positions relative to bedding surfaces. By transforming co-ordinates as perpendicular offsets from a plane representing the local strike and dip, it is possible to elongate the ellipsoidal influence to parallel bedding. By interactively modelling surfaces using CAD facilities and then specifying these surfaces as &apos;hard&apos; or &apos;soft&apos; boundaries, the geologist has complete control over the kriging process.

Jan 1, 1993

By Brett J. R

Some recent and current research and development projects relating to strip type open cut coal mining are reviewed. The projects include a dragline-hopper-truck mining system, an overburden slusher system, improvement of dragline operations, continuous excavation and conveying of overburden materials, and a steep angle coal conveying system. Most of these projects offer prospects for reducing costs in deep strip mining operations, but only the overburden slusher project has the potential for large cost reductions. A project on highwall mining of coal has demonstrated that this coal mining system is viable and capable of achieving high productivity rates. Production highwall mining operations are now starting to become established in Australia.

Jan 1, 1991

By Giuli M, Barnaba P, Sacerdote R, Tammaro F

Following a theoretical consideration of the effect of flooding, fluidisation and softening on blast furnace blowing limits, results are presented which show the effect of these parameters on operation. Industrial trials on Oscar Sinigaglia No. 4 BF are reported and results compared with those obtained theoretically and in the laboratory. It is shown that in these trials the furnace operated at levels of fluidisation very much (80-90%) below those theoretically calculated whereas in some cases (high proportion of sinter) actual hot metal output was near the calculated flooding limit. However, it was observed that as the sinter percentage decreases also actual productivity becomes lower than the one caused by flooding. This gap, which increases as other ferrous components (essentially acidic) replace the basic sinter was explained by the softening of the burden under bosh conditions. Softening indices measured on the individual materials yield support to this explanation. Coke rates data show that for approximately every one percent increase in the basic sinter in place of blended sized ore, a coke rate decrease of 1.1 kg/thm results. For acidic pellets this value is 0.6 kg/thm. Results of breakdown and reduction characteristics are also given and their indices compared with actual pt oduction. Measures to improve operations are proposed.

Jan 1, 1975

By E Amini, M Scott

Grade Engineering® involves the planning, integration and operation of coarse preconcentration techniques to reject uneconomic material as early as possible in the mining value chain to improve the quality of ore delivered to mineral processing activities. These preconcentration techniques include screening for natural and induced deportment of grade to finer size fractions during blasting and coarse breakage, sensor-based measurements of grade and mechanised sorting at particle or bulk scales and coarse gravity separation. Over the last decade, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE), with the support of its participants, has developed a framework for the holistic evaluation of economic and production impacts attributable to these preconcentration techniques. The framework combines the characterisation of preconcentration responses, geostatistical modelling, process modelling and simulation of downstream and upstream production impacts and the optimisation of strategic mine plans to quantify changes in net present value due to different preconcentration strategies. This framework has been applied to evaluate preconcentration techniques at numerous metalliferous operations and can also be used to quantify changes in the environmental metrics for energy, water and steel consumption and emission, tailings and waste rock production. This paper collates the results of these Grade Engineering® studies to show the range and magnitude of economic and environmental impacts attributable to preconcentration. The studies have shown that rejection of uneconomic material prior to mineral processing activities can have a pronounced improvement in energy, water and comminution steel productivity, emission intensity and the profitability of metalliferous mining.

Nov 10, 2020

By M F. Lee

Although the Mt Charlotte gold resource was discovered in 1893, it was only in 1954 that geologists correctly interpreted drill data and defined a large low-grade orebody. The mine has been a large, low-cost and profitable producer since 1962 when bulk mining commenced using cut and fill. From 1968 a combination of long hole open stoping with delayed mass blasting was used. This proved to be an excellent mining method for the large, separate subvertical orebodies. The structured but otherwise good quality rock allowed very large stopes to stand unsupported. Exceptionally large equipment, for its time, was used to efficiently mine, muck and move the ore at low-cost. The mine only just survived severe cost pressures in 1974-76, due to very low gold prices. Better gold prices in 1979 and a need to access deeper ore meant a bold commitment to sink the Cassidy Shaft and refurbish the mine to sustain future profitability. In 1997 the Sam Pearce Decline connected to the underground workings, making it profitable to mine upper level remnant ore. Mining-induced seismicity has been a feature of mining at Mt Charlotte. The main cause has been shearing on structures. A mine-wide seismic system was installed in 1994. Large seismic events have occasionally made management question whether a safe working environment can be maintained. Thorough investigations led to an understanding of the problem and development of procedures to minimise seismicity.

Jan 1, 2000

During the past 18 months a rock mechanics project has been in operation at Renison Limited. The project was established to identify and investigate key problem areas that would affect future production at the Renison mine. An in-house approach was adopted, using shall compact equignent, to investigate ground behaviour. Information on the rock stress field was considered to be particularly important for an understanding of ground behaviour. A high horizontal stress component exists, which enables large flat dipping spans of hanging wall to be opened up, with support being provided by post pillars. The amount of support provided by these post pillars has been found to be low.

Jan 1, 1982

By Neill A. O, Worth I, O&apos

The formation of Kalgoorlie Consolidated Gold \lincs 1&apos;t% Ltd hati pla,xd all the major the gold producing areas adjacent to the city of Kalgoorlie/Boulder under one management, enabling the development of the &apos;Super Pit&apos;. This has facilitated the economic optimisation of the resource. Optimisation has been achieved by the timely collection and presentation of data and the use of these data to reduce costs and improve planning procedures.In particular the following issues have been addressed:ò the reduction of the impact of the mining activity on the adjacent urban population centre,ò implementation of safety procedures for mining through underground voids,ò the determination of the optimum bench height and mining method for ore production benches and blast design. This system is fundamentally based on maintaining a high degree of selectivity while achieving a balance of relatively low unit operating costs,ò assessment of the comparable benefits of contractor versus owner operated earth moving equipment, andò the development of effective ore body models, production reconciliation and the long term mine planning procedures to facilitate effective strategic planning.

Jan 1, 1993

By D Mukendi-Ngalula, G Hearn

Beach sand minerals from the volcanic rock structures of the Drakensberg, Kwazulu-Natal, (South Africa) have been processed. Screening, flotation, spiral concentration and magnetic separation methods were used either separately or successively in an attempt to concentrate monazite minerals. Products thereof and those from a long time (up to 72 hours) microwaves treatment of the finally produced ilmenite-bearing minerals have been studied using the M÷ssbauer effect spectroscopy. The 57Fe M÷ssbauer effect spectroscopy has demonstrated its versatility and power in monitoring the ilmenite internal reduction mechanism and products and, in characterising the iron-bearing phases contained in different products from the beach sand minerals processing. Microwaves heating of ilmenite for up to 38 hours reduced internally the Fe3+ from the ilmeniteÆs structure. A more prolonged microwaves heating (up to 72 hours) re-oxidised the mineral. 61 per cent natural ilmenite recovery was obtained in the floating products of a spiral concentrated -212+106 ¦m screened and beach sand minerals fraction. A preferential concentration of hematite with a 62 per cent recovery was found in the sinking products while the combination of screening-spiral separation-magnetic separation and flotation yielded a floating product with the highest ilmenite and the highest hematite abundanceÆs (71 per cent, 19 per cent respectively). A natural ilmenite containing 87 per cent ilmenite and 13 per cent hematite could be produced and extracted from the sinking products of the flotation process collected subsequently to the spiral concentration and the initial screening.

Jan 1, 2000

Recognition is the most important aspect in the use of breccias as an exploration tool. Ore-hosting breccias occur in a wide variety of environ-ments, shapes, compositions and characteristics, but generally present favorable loci for the deposition of ore mineralization in epithermal, porphyry copper-gold-molybdenum, massive sulfide, carbonate-hosted, sedimentary lead-zinc deposits and others.

Jan 1, 1990

In high stress mining environments, production drill rigs are often employed for rapid drilling of boreholes for systematic cable bolting. One outcome of this drilling method is the need for larger boreholes than would normally be drilled using customised bolting machines, such as the Tamrock Cabolter. Past laboratory studies indicate that, under ideal grouting conditions, borehole diameter has little effect on the pull-out strength of cable bolts with high bulb densities. However, the sensitivity of pull-out strength to large boreholes and less ideal variations of grout strength have not been investigated. To explore these sensitivities, industry standard single embedment tests were conducted on large boreholes simulated using steel pipes. Four borehole diameters were tested, namely: 42 mm, 52 mm, 81 mm and 106 mm. In each case the grout water to cement ratio was varied from 0.35 to 0.45 and two cable bolt bulb spacings were considered, namely: one and three bulbs per metre. The results indicate that, across the range of parameters tested, variations in peak axial load at failure corresponding to changes in hole diameter were statistically insignificant.

Nov 25, 2010

The relative contents of Au in a series of groundwaters from water bores and exploration drillholes, located near Au mineralisation at Stawell, Ararat, Clunes and Ballarat in central Victoria, were found to be clear indicators of relative proximity to mineralisation in each region. In the same series, waters with anomalous concentrations of As distinguished Au mineralisation in bedrock from secondary palaeochannel or deep lead Au. In some groundwaters, acid pH values, high sulphate relative to other anions and detectable concentrations of reduced Fe reflected sulphide minerals associated with bedrock Au deposits. Close to some ore zones, locally anomalous groundwater concentrations of Mn reflected the Fe carbonates that accompany Au in these zones. In addition, elevated concentrations of other elements provided geochemical signatures for the aquifer lithologies associated with Au mineralisation. Of the lithological indicators Co and Ni, U and F, Rb and Cs, Mo and Li respectively reflected the mafic, felsic, potassic rich and quartz zones, principally in the Stawell mine area and to a lesser extent those at Clunes and Ballarat. Mineral stability diagrams, based on groundwater activities of K&apos;, Mgt and H`, demonstrated that a series of ore-zone groundwaters follow a trend that conforms with a biotite to sericite to kaolinite alteration sequence in aquifer mineralogy. This is a good illustration of how present day groundwaters under surface conditions can reflect the underlying mineral sequences that accompany these Au deposits. These observations around mine areas suggested that groundwater chemistry could provide a rapid and cost effective method of assessing prospectivity for An of extensive areas in central Victoria. To test this, regional sampling and analysis of 355 bore waters was carried out in a region where potential An bearing rocks are covered by Mesozoic and Cainozoic sediments and volcanics. Contoured elemental abundances and distribution from this program indicated five zones in which groundwaters had elevated Au and despite the cover, appeared to reflect variations in the underlying Palaeozoic rocks. Three of the Au zones could be in terrain affected by extensions or intersections of faults, a feature in common with the established Au deposits in central Victoria. Reflections of concealed Palaeozoic rocks included a possible zone of concealed Cambrian greenstones that coincides with three of the Au zones. It was concluded that each of the An zones represents a groundwater Au focus that warrants follow-up exploration.

Jan 1, 1997