Search Documents

[Note.—The paper of Mr. W. H. Hoffman (Glen Summit, October, 1891; Trans. xx., 602), on "Practical Results in the Magnetic Concentration of Iron-ore," together with a paper by the same author (Baltimore, February, 1892; Trans. xxi., 126), on "Granulating Magnetic Iron-Ores with thesturtevant Mill atCroton Magnetic Iron-Mines, N. Y.," and also the papers Presented at this meeting,

Jan 1, 1893

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metal-lurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial invest-ment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding.

Jan 1, 1939

By H. W. McCue, Henry Rogatz

Oil.—During the year 1939, there were 365 oil wells drilled in the Texas Panhandle, with a total daily initial production of 130,968 bb1.— that is, 69 fewer oil wells drilled than in the previous year, with a decrease. in total daily initial production of 61,738 bbl. The total daily potential of the field on Dec. 5, 1939, as determined by the Texas Railroad Commission, was 1,344,677 bbl., an increase of 94,032 bbl. over the previous year. On Dee. 5, 1939, a daily allowable of 130,527 bbl., which was an

Jan 1, 1940

By Henry Rogatz, H. W. McCue

Oil.—During the year 1939, there were 365 oil wells drilled in the Texas Panhandle, with a total daily initial production of 130,968 bb1.— that is, 69 fewer oil wells drilled than in the previous year, with a decrease. in total daily initial production of 61,738 bbl. The total daily potential of the field on Dec. 5, 1939, as determined by the Texas Railroad Commission, was 1,344,677 bbl., an increase of 94,032 bbl. over the previous year. On Dee. 5, 1939, a daily allowable of 130,527 bbl., which was an

Jan 1, 1940

By J. C. Smock

The magnetic and polaric properties of magnetite, or magnetic iron ore: are fundamental facts in magnetism. The disturbing erect of this mineral upon the magnettic needle in land surveying must have been very early observed. The difficulties arising from this source are still almost insurmountable in making accurate surveys in districts where this ore occurs to any extent, either as a rock

By Julien Deby

The sinking of a deep shaft is always a serious undertaking, especially when the strata to be traversed are of great hardness, or when they are feebly coherent or highly saturated with water. In the. first case, that of solid rock, modern appliances, such as the rock-drill, put into motion by air-compressors, along with suitable explosives, will generally answer the purposes of the mining engineer until he has reached the main water-levels. When these have

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metal-lurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial invest-ment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding.

Jan 1, 1939

By Harrison Schmitt

DURING the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. HANOVER, NEW MEXICO The Hanover; New Mexico, zinc deposits were briefly described by Lindgren and others,1 Paige2 and recently in more detail by Schmitt.3 These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive 3/4 mile wide and 2 1/2 miles long (Fig. 1). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike; thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1933

By Franklin H. Sharp

The operation of the Magmont Concentrator located on the New Lead Belt of Southeast Missouri is described. Ore characteristics affecting lead-copper-zinc separation are enumerated, and the cur- rent methods of separation are detailed.

Jan 1, 1976

By S. F. Bartram, G. A. Chase

COMPUTED X-ray diffraction powder patterns of YNi3, YNi5, and CbBe3 are available on request from either author.

Jan 1, 1968

By S. C. Oliphant, C. R. Houssiere, George H. Fancher

DRILLING mud can be an item of great expense on the Gulf Coast. In order to understand the nature of a drilling mud, it is desirable to know the composition and size of the mineral particles that are present, The supercentrifuge has been adapted to the fractionation of mud, and this paper discusses the calibration and methods of operation and control. An alignment chart has been prepared, which was found useful in this work. Typical data are included, showing the comparative reliability of the method.

Jan 1, 1942

By E. Mcl. Tittmann

Deep-seated human instincts urge us to positively mark the passage of time. We celebrate the passage of each year. Years give way to decades, and decades to half centuries and centuries. At all these mileposts we are inclined to pause, take a look around and catch our breaths before embarking on the next leg. We are at such a point now and this meeting I am sure will give direction to the road ahead into the decade of the seventies. In looking around at this point, 1973, it is obvious to all of us that the environment in which we must mine, mill, smelt and refine lead and zinc has radically changed. These changes have, of course, occurred over a long period of time. They have, however, all been in the same general direction. They have all had the same motivation. The period of greatest contrast is probably the fifteen years just before World War II and the fifteen years following the end of that war. I thought that I might review briefly with you what seems to me to be four of the more important changes that have developed since World War II that profoundly affect our activities in the lead and zinc industry. I mentioned before that all these changes have been in the same direction; that is, they have all tended to restrict our freedom of action in pursuing our objective of producing lead and zinc on a competitive basis at a profit. Consequently, in discus- sing them you may think that I am merely viewing with alarm. This is not the intent. This is merely supposed to be an objective analysis. I think it appropriate before discussing these trends in de- tail to examine the position of lead and zinc today.

Jan 1, 1970

By R. W. Raymond

I desire to call the attention of members of the Institute to a new method of plotting and determining faults in mineral deposits, suggested by Prof. Hanns Hoefer, lately of the Mining School of Przi-

Jan 1, 1882

By M. J. Taffanel

I AM very much impressed by this manifestation of international brotherhood; the mining engineers on both sides of the ocean have similar subjects to deal with, meet with the same difficulties, expose themselves sometimes to similar dangers; they are like companions in arms in the battle fought by mankind in order to subjugate the natural forces and to draw profit therefrom. There is no other field where this fraternity must manifest itself more actively than in the studies pursued with a view to improving the safety of mines and to rendering impossible in the future these mining disasters, which every year claim hundreds of victims. These are very difficult problems, the solution of which requires numerous and laborious experiments accompanied by very arduous scientific investigations; it is extremely desirable that the various mining countries, which have undertaken to solve these difficult problems, should unite their efforts in order to succeed as soon as possible and as well as possible. This idea has been fully grasped by your Bureau of Mines, which has brought me to Pittsburg; the daily exchange of views with the distinguished chief of-the mine investigation division, George S. Rice, and with his excellent collaborators, the comparison of the results obtained at Lievin and Bruceton, the checking of these results by means of new tests, the profound study of the measurements, diagrams, measuring and laboratory apparatus, the cooperative investigation of new apparatus, or the preparation of new investigations, are, I hope, of such a nature as to bring about great progress. I think that it will be interesting to you to know what has been done in France along this line.

Jan 9, 1914

ALBERT SAUVEUR, Chairman. A. A. STEVENSON, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, William Kelly, J. S. Unger, William H. Blauvelt, Charles Kirchhoff, Felix A. Vogel, James Gayley, Richard Moldenke, Leonard Waldo, Henry D. Hibbard, Joseph W. Richards, William R. Walker, Henry M. Howe, C. F. W. Rys, William R. Webster, Robert W. Hunt, E. Gybbon Spilsbury, Frederick W. Wood. J. E. Johnson, Jr., The innovation of a special meeting under the auspices of the Iron and Steel Committee was well justified, if we accept as a criterion the number of papers presented at the meeting held on Oct. 16 and 17 in New York and the attendance at that meeting. Twenty-four papers were read, and most of these were widely discussed orally, while doubtless the written discussions will be even larger in extent. Discussions will be received up to Dec. 1, 1913. The attendance at the meeting of 106 members and 75 guests is an evidence of the wide anti growing interest in the Institute of men interested chiefly in iron and steel. It is especially interesting to note this large attendance at a meeting where very little of a social nature was introduced into the program. An informal dinner for the men at the Engineers' Club closed the meeting. At this dinner were present about 70 members and guests. One of the Vice-Chairmen and the Secretary of the new Committee on Petroleum and Gas told of the important plans in prospect of that Committee. Brief impromptu speeches by a considerable number of the members and guests were enjoyed. Professor Marburg reiterated his previous assertion that he believed that the Institute and the American Society for Testing Materials, as well as some of the other technical societies, were all fighting for one good cause; that there was room in the field for all of these societies with their various points of view; and that they should march shoulder to shoulder. The success of this dinner was due largely to the efforts of Mr. Johnson who had the affair in charge.

Jan 11, 1913

By S. P. Kinney, C. E. Wood, T. L. Joseph

In connection with its investigations of the blast-furnace process, the Bureau of Mines, in cooperation with the Minnesota School of Mines Experiment Station, developed a 6-ton experimental furnace. Such a furnace was needed to determine the feasibility of producing ferroman-ganese from Minnesota manganiferous iron ores, a problem of national importance because of the present need for manganese in the steel industry and our small reserves of ferro-grade ores. Furnace operators are reluctant to use new or untried raw materials or to make decided innovations in practice on account of the financial hazard of experimenting with full-scale equipment. A small furnace which can be operated at a relatively low cost is particularly adapted for testing new raw materials and for determining the feasibility of decided innovations in practice. Laboratory experiments, plus whatever information may be available, are valuable but often do not indicate the net result of changes in an operation involving a large number of interrelated variables. From time to time the cooperation of the Bureau of Mines is solicited in connection with problems involving departures from normal procedure. Under these circumstances some sort of a practical demonstration is a desirable forerunner to full-scale operations which appear feasible after small-scale tests. The Aluminum Co. of America was interested in knowing the practicability of smelting a charge of bauxite, iron ore, and limestone, of proportions that would produce slag of the following composition: A1203, 47 to 48 per cent.; CaO, 41 to 42 per cent.; SiO2,4 to 5 per cent.; TiO2, 2 to 3 per cent.; FeO, 1 percent., and MgO, 1.8 percent. In addition to determining whether it was feasible to operate a blast furnace on slag approaching the composition given above, a quantity of slag was needed for a series of experiments that would show the relative ease and cost of extracting alumina from slag which could be made in the blast furnace, as compared to extracting it from raw bauxite. The value of the slag as a raw material

By W. Tovote

This paper is based upon 12 years' experience in the Southwest, including three years that were spent in constant traveling as examining engineer for the Phelps-Dodge Corporation. The material was gathered during rather extensive work in Bisbee, Clifton-Morenci, Globe, and Tombstone, and also on short and rapid trips into most of the mining camps and prospect fields of New Mexico, Arizona, the desert country of California, and as much of Sonora as was safe at the time. My methods of observation and my deductions are not put forward as new or scientific; they are simply rough field methods, based upon short notes, rough sketches, and largely upon memory, which I have found useful for coördinating geological data for the purpose of passing quick judgment on mining possibilities in certain districts exhibiting uniform characteristics. The opportunities for observation have been better these last few years than ever before, due to the unprecedented activity in mining, which has caused the reopening of hundreds of old mines and the starting of even more numerous prospects all over the mining states. Possible Systems of Classification By Geological Provinces There are a number of well defined geological provinces in the territory under discussion, and a study of their individual features is of interest. The following are a few of those that are most striking in their uniformity. 1. The "Desert province," extending roughly from Wickenburg, Ariz., to and beyond Barstow, Cal. In its north-south extent it reaches up to the Colorado River and down into Sonora, but overlaps other provinces. It is characterized by a worn-down basement of schistose and granitic rocks, on which rest remnants of Paleozoic and pre-Paleozoic sediments, including very old limestones. The sediments are disrupted and contorted. Alteration in the mineralized areas is very prominent, especially in the schists and limestones. Cenozoic volcanic rocks, principally of semi-basic composition, have been intruded into this complex and sometimes cover it as lava flows. 2. The "Yavapai schist" province, similar to the one first mentioned, consists of metamorphosed basic and semi-basic rocks. It lies in northern

Jan 1, 1920

By Arthur Anderson

OUT of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Inno-vations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these fea-tures that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the season of 1936 the first effort. was made to use heavy truck haulage in the trans-portation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in low gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1938

By W. R. Ingalls

THE manufacture of zinc oxide directly from the ore is one of the most important contributions that America has made to the metallurgy of zinc. Heretofore, this has been clone chiefly for the production of zinc and zinc-lead pigments, and the method has been known as the Wetherill process. While that term may properly be applied to the process for pigment manufacture, it must be recognized that the principles of the process are of far wider application; and that there is going to be wider application in the immediate future is more than an expectation. I have in mind the use of the process as a method of igneous concentration. Igneous concentration is broader in its scope than the Wetherill process, for it may be done in the blast smelting furnace, or in the reverberatory, or by other means. Igneous concentration is a rather clumsy term, and I prefer to introduce the new generic expression of "zinc burning," which is convenient, readily understood and precise, for in all cases the zinc oxide is reduced to metallic form, is volatilized and is then burned to zinc oxide, the latter happening, however, after the zinc has been separated from the residue of the ore. As previously indicated, zinc burning may be done either in blast or reverberatory smelting, the gangue of the ore being scorified and drawn off as slag, while other metallic minerals are reduced to matte or metal. Such processes have heretofore been practised on fairly large scales. Thus, F. L. Bartlett smelted zinc ores at Canyon City, Colo., in specially designed blast furnaces, wherein the smelting column was only about 18 in. high. Such a limitation was necessary in order to prevent zinky accretions in the shaft of the furnace, which in course of time would have interfered with its operation. In running the Bartlett furnaces it was easy to bar them off, indeed, to poke right down into the smelting zone, and keep things going freely. Some iron blast furnaces in Virginia and the spiegeleisen furnaces of the New Jersey Zinc Co. afford other examples of zinc burning in blast-furnace smelting, although in their cases the happening is incidental rather than a primary purpose.

Jan 9, 1917

By F. Cadena, Fred C. Bond, Walter L. Maxon

Grinding is one of the major problems in present-day milling practice, and in many cases, it represents one of the main items of expense. It becomes necessary from time to time, to compare grinding practice in one plant with that in another plant, and in making such comparisons, it would be very desirable were there available accepted standards of grinding resistance for the materials involved. Such a set of grinding constants would also be of considerable value in planning new grinding installations. There have been some tests published, notably those of Lennox,' which have been generally cited as a basis for such comparisons. Most of the tests made have been based upon open-circuit grinding, in which a weighed sample of the ore was crushed to pass a certain mesh, and was then ground under certain conditions, either wet or dry. Grinding was continued until a certain desired fineness was attained, and the comparisons based on the grinding time, or the samples were all ground for a certain specified length of time and comparison based upon the screen analysis of the products. Such methods have been acceptable where the ore was to be ground in open circuit. However, in modern milling practice, many grinding problems involve closed circuits wherein the oversize returns to the mill and a large circulating load builds up. A method of testing that does not take the circulating load into consideration might yield results quite different from those to be expected in practice, because the minerals in the ore that offer maximum resistance to grinding will accumulate in the circulating load up to an equilibrium value. Thus the nature of the ore charge in the mill at any instant may differ greatly from that of the new feed, with a consequent error in the rate of grinding determined by such a method. For example, let it be assumed that an ore to be tested consists of equal parts of difficult grinding mineral and easy grinding mineral. This is to be compared with an ore used as a standard, and consisting of minerals which are all of about the same grindability. If a comparison

Jan 1, 1935