Search Documents

By Ronald E. Versaw

Environmental legislation, both existing and proposed, requires that mills, tailings dams, evaporation ponds, and related processing facilities be located, constructed, and operated within stringent guidelines. An early step in planning a new processing facility is performing a site selection study in which topographic, hydrologic, geotechnical, and environmental parameters are evaluated for several alternate sites. Once a site is selected, then an environmental report, including a description of the proposed action, alternatives, baseline surveys, and discussions of potential environmental impacts, mitigation measures and monitoring programs is required. The federal legislation, siting studies, and environmental studies (along with the implications of these as they affect design) are discussed. In addition, costs for performing these studies and implementing control of effluents are discussed.

Jan 1, 1978

By Olin G. Bell

During the year 1928 ten new producing areas have been discovered and several extensions in oil and gas fields have been found in southwestern Texas. This year, however, will reveal itself as one of small profits in spite of considerable increase in production for the area as a whole over the previous years. At the beginning of 1928 the fields in this area (Fig. 1) were producing a daily average of 7500 bbl. from 730 wells, whereas at the close of the year the daily average had increased to approximately 14,000 bbl. from 827 wells. Production for the year was 3,453,938 bbl. The total oil produced in Southwest Texas since its discovery has been 16,955,-388 barrels. (Table 1.)

Jan 1, 1929

By F. C. Farnham

In this paper it is shown that the vertical component of the earth's magnetic field for the area of the United States can be very closely approximated by assuming it to be the sum of the vertical components of two magnetic fields. The first of these is the field of the centered dipole described by J. Bartels,l the axis of this dipole intersecting the earth's surface at two antipodal points, the one in the Northern Hemisphere being at latitude 78.5°N. and longitude 69°W., and the dipole having such strength that the vertical component of its field at its axis pole is 0.63 oersted. The second field is that due to a second dipole situated halfway between the center of the earth and a point on the earth's surface at latitude 38.5°N., longitude 91.5°W., the axis of this dipole being along this radius, the south pole being toward the surface, and the dipole being of such strength that its field at the point on the surface mentioned above is 0.069 oersted. Using the field computed on this basis, tables of latitude and longitude correction factors were computed and are included in the paper. It is also shown that the secular variation in the earth's magnetic field may be roughly accounted for by assuming it to be due to motion of the second dipole described above. Although there is an error in the equation used for computing the strength of the field due to the second dipole, the distribution of the field computed is very nearly that of the assumed arrangement of dipoles. Subsequent work by the author reveals that minor changes can be made in the location of the second dipole, which will make the computed field fit the observed field even more closely. It has also been found2 that the vertical component of the field may be represented equally well by a purely empiric relationship.

Jan 1, 1940

By F. C. Farnham

In this paper it is shown that the vertical component of the earth's magnetic field for the area of the United States can be very closely approximated by assuming it to be the sum of the vertical components of two magnetic fields. The first of these is the field of the centered dipole described by J. Bartels,l the axis of this dipole intersecting the earth's surface at two antipodal points, the one in the Northern Hemisphere being at latitude 78.5°N. and longitude 69°W., and the dipole having such strength that the vertical component of its field at its axis pole is 0.63 oersted. The second field is that due to a second dipole situated halfway between the center of the earth and a point on the earth's surface at latitude 38.5°N., longitude 91.5°W., the axis of this dipole being along this radius, the south pole being toward the surface, and the dipole being of such strength that its field at the point on the surface mentioned above is 0.069 oersted. Using the field computed on this basis, tables of latitude and longitude correction factors were computed and are included in the paper. It is also shown that the secular variation in the earth's magnetic field may be roughly accounted for by assuming it to be due to motion of the second dipole described above. Although there is an error in the equation used for computing the strength of the field due to the second dipole, the distribution of the field computed is very nearly that of the assumed arrangement of dipoles. Subsequent work by the author reveals that minor changes can be made in the location of the second dipole, which will make the computed field fit the observed field even more closely. It has also been found2 that the vertical component of the field may be represented equally well by a purely empiric relationship.

Jan 1, 1940

By L. L. Brundred

The major portion of the production of the Gulf Coast area, represented by South Texas and South Louisiana, comes from the flanks of well-defined salt domes. This oil, containing an excellent lubricating stock, ranges from 17° to 28° Be. gravity. Some lighter oil is encountered but the life of such fields is, in general, an open question. In fact, there are few light-gravity fields which have proved of much value. In all of the fields water encroachment, or, more properly, water produced with the oil, is a vital factor. After the first head of high-pressure gas is removed, ever-increasing percentages of water appear, and naturally the life of the wells is materially affected thereby. The sands are, as a rule, extremely fine, very soft, and must be carefully excluded from the hole by the use of fine screen to prevent sanding up. All sands are tipped at such extreme angles as to make coring essential for the location of water strata, oil-bearing sands and important shale. beds. Even with modern coring, the correlation of logs is a difficult problem. Due to the fact that the bulk of the oil is refined for its lubricating properties, little attention has been paid to losses by evaporation in the field. This is largely influenced by the fact that the major companies have set a price schedule, showing but two grades, "A" and "B." The average oil company, therefore, does not attempt to use the gas-lift but relies primarily on the air-lift and then only on wells considered to be particularly adapted to its use, namely those capable of producing large quantities of fluid and yet not having sufficient "kick" to flow. Furthermore, as the gas contained in the reservoirs is mostly ricthane such gas being very quickly vaporized and produced in large quantity in the early life of the fields, there is little gas left after the first flush flowing period of the wells. In fact, it is very generally conceded that gas is a precarious fuel to depend on in any of the coastal fields. This situation largely accounts for the fact that air, as the lifting medium, is almost universally used. In the average field, wells are drilled on the flanks of the domes in close proximity to one another, largely on account of the extreme dips of the formation and "town lot" leases, and space to set up machinery and

Jan 1, 1928

By P. C. Kelly

The processes involved in turning a set of seismograph records into a geological structure map may be divided into three classes; (1) picking reflections on the records, to be used for the computations; (2) determining the basis on which the computations should be made in order to arrive at correct results; (3) making the necessary computations and plotting sections and maps. The first is usually done by the crew chief, or at least checked by him. The computing system usually originates in the head office, occasional consultations with the party chief providing modifications as necessary to meet special conditions. The computations and plotting are done by the party computer, with possibly one or two assistants if the calculations require much time. Picking the Rejleclions Marking of the reflections on the records is perhaps the most important step and the one most likely to determine the reliability of the final results. Making the "picks" is important because most of the problems that come up in practical work are connected with the problem of what can be done with poor records. The lack of any definite criteria by which to judge what are good and usable reflections is at the bottom of the difficulty. Give the same set of records to several people to mark and they will probably come out with a variation in the number of reflections per record that are deemed usable. With good records the correct picks are obvious to all, but with poor records experience seems to be the only reliable guide as to what picks are reliable and what are merely born of imagination and desperation. Experience in marking records and seeing how the structures eventually check out is more important than training in physics or geology. Different types of equipment and shooting methods may produce records quite different in appearance, from the same territory, and the computer can do his best work with records of a type on which he has had considerable experience, and has learned the limitations and shortcomings as well as the virtues of the data with which he is working. Reflections may be picked for dips only, in which case the particular reflection picked is not recognizable with certainty on records from any other spread. For the purpose of computing dips it is necessary that the reflection be marked on a11 or nearly all of the strings of the records, as

Jan 1, 1940

By P. C. Kelly

The processes involved in turning a set of seismograph records into a geological structure map may be divided into three classes; (1) picking reflections on the records, to be used for the computations; (2) determining the basis on which the computations should be made in order to arrive at correct results; (3) making the necessary computations and plotting sections and maps. The first is usually done by the crew chief, or at least checked by him. The computing system usually originates in the head office, occasional consultations with the party chief providing modifications as necessary to meet special conditions. The computations and plotting are done by the party computer, with possibly one or two assistants if the calculations require much time. Picking the Rejleclions Marking of the reflections on the records is perhaps the most important step and the one most likely to determine the reliability of the final results. Making the "picks" is important because most of the problems that come up in practical work are connected with the problem of what can be done with poor records. The lack of any definite criteria by which to judge what are good and usable reflections is at the bottom of the difficulty. Give the same set of records to several people to mark and they will probably come out with a variation in the number of reflections per record that are deemed usable. With good records the correct picks are obvious to all, but with poor records experience seems to be the only reliable guide as to what picks are reliable and what are merely born of imagination and desperation. Experience in marking records and seeing how the structures eventually check out is more important than training in physics or geology. Different types of equipment and shooting methods may produce records quite different in appearance, from the same territory, and the computer can do his best work with records of a type on which he has had considerable experience, and has learned the limitations and shortcomings as well as the virtues of the data with which he is working. Reflections may be picked for dips only, in which case the particular reflection picked is not recognizable with certainty on records from any other spread. For the purpose of computing dips it is necessary that the reflection be marked on a11 or nearly all of the strings of the records, as

Jan 1, 1940

By C. Goldberg, R. H. Wynne

WHEN using an optical goniometer to determine crystal orientation' it is advantageous to use a preferential etchant so that the etch pits have plane faces which are parallel to crystallographic planes, all of which are of the same "form." "Westinghouse Silver Etch" (WAg), a preferential etch for germanium, is made up as follows: 40 ml of 49.7 pct hydrofluoric acid, 20 ml of 70.7 pct nitric acid, and 40 ml of distilled water containing 2.0 g of silver nitrate. Examination of metallographs of WAg etched surfaces (Fig. 1, for example) indicates that, regardless of crystal orientation, the faces of the etch pits are (111) surfaces. Optical goniometer examination of these WAg etched surfaces also indicates that the faces of the etch pits are (111) surfaces, i.e., all bright reflections are from (111) planes. When using an optical goniometer of the type described by Barrett,' not only (111) reflections from a WAg etched germanium surface but also other reflections of lower intensity will be observed. These latter reflections can cause confusion. We have used an optical goniometer made from a war surplus astrocompass and a galvanometer lamp. The reflections are observed by using the goniometer in a darkened room and letting the reflected light be in- cident upon a piece of white paper. The resulting decrease of goniometer sensitivity enables (111) reflections only to be observed. This in turn permits the crystal orientation to be determined in a matter of minutes, since only two measurements are necessary. The authors wish to acknowledge the help received from R. E. Davis who assisted in making the metallographs and aided the authors in the interpretation of the metallographs.

Jan 1, 1954

By W. L. Grose, J. E. Nealy

A device developed by the U.S. Bureau of Mines for the detection and quenching of coal mine explosions suffers from the inability to discriminate between the light emitted from hydrocarbon combustion and that emitted by electrical sparks and miner's cap lamps1. Since the quenchant device is activated by an internal explosive charge, the possibility of serious injury to nearby personnel demands a detector which can reject false signals. Described herein is a detector which can provide a rapid response signal upon the emission of radiation from hydrocarbon combustion and concurrently reject spurious signals from such sources as sparks and cap lamps. It was suggested that a detector might be developed to operate on the principle of monitoring the radiation intensity emitted from two separate spectral regions and ratioing the intensities2. A series of experiments was conducted for combustion of methane-air mixtures which demonstrate the ability of such a detector to discriminate between combustion and spurious signals. Experimental Apparatus A cylindrical (3.8 in. diam by 12 in.) stainless-steel shock tube test section was used as a combustion chamber. The test section was equipped with quartz windows (2 in. diam) on either side, a piezoelectric pressure transducer, and two steel electrodes. A 10-kv capacitor discharged across the electrodes provided a submicrosecond duration spark to ignite the gas mixture within. The desired partial pressures of methane and air were obtained by using a Wallace and Tiernan 0-800 mm Hg pressure gauge with which pressures could be determined to an accuracy of % mm Hg. All tests were conducted with a total pressure of 1 atm in the chamber. To

Jan 1, 1972

* A demonstration pipeline for transporting coal will be constructed by Pittsburgh Consolidation Coal Co, at the Georgetown strip-mining operation near Cadiz, Ohio, The 12-in., 17,000-ft line, special crushing and preparation equipment, and pumps especially designed for the operation will cost about $550,000. A slurry of fine coal and water will be fed into the line and moved through it under pressure. * Sulphur resources in the U.S. are being rapidly exhausted with no new major deposits being found, This common mineral may become one of the most strategic items during the next five years. Recovery of sulphur from pyrites is being considered in case of an emergency. Already the British have adopted stringent measures to conserve sulphur supplies.

Jan 3, 1951

By W. R. Opie, O. W. Mole

By confining the electrolytic reduction of TiCl4 to the interior of a porous basket-cathode the electrolyte between the anode and the cathode can be kept free of reduced chlorides of titanium eliminating undesirable reactions of reduced titanium chlorides with brickwork or oxygen in the cell atmosphere. Semiwalls are not needed. Operating conditions are given and discussed. Titanium yields based on TiCl4 introduced are 93 pct. Cell voltage and amperage characteristics are adaptable to multiple cathode-series cell urmngements. EXPERIMENTS conducted in the National Lead Co., Titanium Division, Research Laboratories showed that titanium metal could be deposited in an electrolytic cell in which titanium tetrachloride was introduced through a tubular cathode.' The reduced chlorides as formed were confined to the vicinity of the cathode. They were reduced to form a cocoon-shaped growth of sponge titanium metal at the end of the cathodic tube below the surface of a sodium chloride-strontium chloride electrolyte. No diaphragm was needed.' Although high-purity, coarse crystalline metal was produced in the cocoon growth, the yields of metal removed from the cell, based on the amount of titanium introduced as TiCl4, were usually only 40 to 60 pct. The growth of the cocoon deposits was away from the cathodic tube for introduction of TiC14 toward the anode following the flu lines. The reduced chlorides of titanium diffused through the deposit and were reduced to titanium electrolytically within the deposit or on the outer surfaces. Deposition within the pores of the cocoon was detrimental to further deposition because it plugged the passages used by the reduced chlorides to diffuse away from the point of titanium introduction. As plugging due to deposition in the pores proceeded, the reduced chlorides in the center of the cocoon would force their way out by forming a channel and would escape from the vicinity of the cathode without being reduced to metal. Some work had been done previously1, 2 which indicated that if the end of the cathodic tube for introducing TiC14 was surrounded by a screen connected to the tube so that it too was cathodic, growth could be made to occur within the screen. Direction of growth was observed to be from the screen toward the point of TiCl4 introduction. Through a series of design modifications a cathode evolved which consisted of an introduction tube surrounded by a perforated metal basket as shown in Fig. 1. Modifications of this design are described in Refs. 3, 4, and 5. This basic cathode designa" was incorporated in electrolytic cells containing graphite anodes and constructed of high-silica brick refractory for containing the electrolyte (see Fig. 2). The inner crucible was surrounded by insulating brick and the entire unit contained in a welded steel shell. Suitable cooling chambers with inert gas atmospheres were devised so that the cathode could be removed from the cell without exposing the deposit to air while hot. Various alkali and alkaline earth chlorides were used as electrolytes.

Jan 1, 1961

By P. Bouéry

This account of a contrivance which has been found serviceable in practice may be of interest to engineers, and especially to those engaged in hydraulic mining. In that process, one feature which seems at first sight to possess little significance, is highly important in its effects—namely, the regular supply of water to the " giants." The chief condition of this regularity is an even flow in the pipe-line from the penstock to the nozzle.' This, of course, requires that the penstock be kept full. Any considerable surplus of water, overflowing at the penstock, is a simple waste, unless it be otherwise utilized in the sluices. At all events, it does not affect the delivery of the nozzles. But a deficiency at the penstock may admit air into the pipe; and this may produce hydraulic recoil, injuring the line by incessant vibrations, giving rise to leaks, and even to blow-outs, and (when a partial vacuum exists at the time of the fracture) the collapse of the pipe. An accident of this sort in our main pipe-line, occasioned partly by a settling of the ground and partly by the presence of air in the pipe, led to the employment of the device here described. The line referred to is made of 30-in. pipe, successively reduced to 18 and 15 in. in diameter, for the supply of two giants. By reason of the causes above mentioned, the 30-in. pipe burst more than 1,400 ft. from the penstock, and, despite the air-valve, the 30-in. pipe was collapsed to such a degree that one length of it, next to the penstock, was squeezed together and positively swallowed by the main pipe, through which it traveled for 750 ft., piercing through a short elbow on the way. This remarkable result was undoubtedly the effect of the vacuum suddenly produced when the pipe burst.

Jan 1, 1907

By H. A. McKinstry, F. F. Lange

A vector analysis of orientating single crystals using the Laue back-reflection X-ray technique is given. Briefly, the analysis involves using a few data taken from a Laue photography and defining the crystal co- ordinate axes in a reference coordinate system. After a few matrix multiplications, the proper goniometer angles can then be determined to orient the crystal coincident with the reference frame. This analysis is easily programed for a digital computer to provide a fast, precise, and efficient method of orienting many crystals which are identical. The general procedure is as follows. The crystal is mounted on a goniometer. Laue photographs are taken until an array of diffraction spots is observed that includes a Laue spot that represents a rotational axis of symmetry. The rotation angles of goniometer are recorded. These angles are defined as positive for a counterclockwise rotation. When the axis of symmetry is located on the Laue photograph, the crystal coordinate axes can be defined in the reference coordinate system* as follows. Two Laue spots are chosen, one of which corresponds to the rotational axis of symmetry and the other to a set of planes whose zone axis is a known crystallographic direction and normal to the rotation axis of symmetry. The Laue spots are used to determine these two crystal directions in the reference coordinate frame. This is done by placing the Laue photograph on a sheet of polar coordinate graph paper and determining the polar coordinates (r, o) of these two diffraction spots in the reference coordinate frame. Their third coordinate is the distance between the crystal and the film (-D). The coordinates Xni of the two crystal directions Nn, (n = 1, 2) in the reference frame are then calculated by the following equations: Xn1 = -D X2n = Ancos on X3n = A, sin on where -tan- 1 rn/D An =Dtan(tan-1rp/D/2) By taking the proper cross products of these two directions (normalized to unit vectors), the crystal coordinate axes 3 (i = 1, 2, 3) can be determined in the reference frame. This is illustrated in Fig. 1. The next step is to determine the relation between

Jan 1, 1969

By J. S. Wakeman

The techniques of testing the physical properties of green pellets produced in a batch balling test are described. It has been found that these physical properties, i.e. drop resistance, wet compressive strength, and plastic deformation under load, are generally related to the moisture content of the wet balls. A "criterion" method of analyzing data from a series of batch tests is discussed. This method facilitates the comparison of results of various test series. A time-sharing computer program, which correlates the test data from a batch series, generates the "criterion" values for subsequent comparison and analysis, and produces X, Y plots of the various moisture-strength relationships, is presented. Examples of computer output and use of the "criterion" evaluation method are given.

Jan 1, 1973

By Floyd C. Kelley

The literature of the last decade is rich with information relating to the cause and means of control of grain growth in pure metals, but is deficient concerning the role diffusion plays in grain growth, although during this period many new products that depend on diffusion for their properties and success have been developed. Among these are cementation products, produced by calorizing, chromizing, and carbonizing, or by mixing, pressing, and sintering powdered metals such as Syke's iron-molybdenum die material, Genelite, and Elcon Metal (copper, tungsten) etc. This is a fertile field for new developments, but before it can be utilized to the fullest extent there must be a thorough invest,igation of the processes by which diffusion and grain growth take place. Grain growth plays no small part in the process and certainly the physical properties of these products depend largely on the grain size and state of equilibtiuni produced. The field of investigation does not end here, but may be extended to the effect of diffusion on impurities, segregations and dendrites in the broad field of ferrous and non-ferrous metallurgy. A number of years ago the author investigated several of these cases and noted, with striking regularity, the pronounced effect of diffusion in promoting recrystallization and grain growth. An example of this phenomenon is given in his paper on chromizingl which contained photomicrographs of large radial or columnar crystals produced by diffusion of chromium in the solid state. Another manifestation of this effect was discussed by Austen,2 who showed the part hydrogen plays in the decarburization of steel and the effect of diffusion upon the grain structure. Diffusion of Metals in Iron It seems to be a general law, whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, that a comparatively rapid, or abnormal, grain growth results. The grains

By F. H. McDowell

The electro-magnetic separator of Mr. G. Conkling, Glens Falls, N. Y., described by Mr. Birkinbine* in a paper at the New York meeting of the Institute, in February, 1889, has been in successful operation at the Tilly Foster 'mine for a considerable period, under the disadvantages which seem to be the inevitable attendants of pioneer enterprises in new technical fields. The results of a run of several months, which the Superintendent, Mr. S. P. Tomkins, has taken pains to collate, are here presented by his courteous permission, and that of Mr. E. S. Moffat, the energetic and skilful General Manager of the Lackawanna Iron and Coal Company, to whom our profession is already indebted for examples of bold and ingenious practice in mine-engineering. It is believed that these figures will assist those who are planning similar operations to decide intelligently what they may, and, more important still, what they may not, expect to accomplish. The local difficulties in the way of this experiment at the Tilly Foster mine were many and great. Only about two-thirds of the waste-dump, resulting from the assorting of previous years, is ore; and this varies in content of iron from 20 to 28 per cent. The remainder is rock, some (from horses in the vein) showing particles of adhering mineral, some (from the foot- and hanging-walls) entirely barren. The expense of overhauling the dump and removing this rock is by no means the least of the numerous items which must be charged against the concentration. Associated with the lean ore are hornblende and other minerals, carrying iron in the non-magnetic state, which must necessarily be washed away with the tailings. The waste-dump was originally located without reference to future treatment, and now can only be handled by means of a locomotive,

Jan 1, 1891

By Arthur S. Dwight

The profeseional career of Thomas Septimus Austin, who died at El Paso, Tex., Aug. 23, 1906, was contemporaneous with the growth of the silver-lead smelting-industry of the Far West, to which his talents and zeal contributed in no small degree. Born at Stratford, Conn., Dec. 7, 1853, he was the seventh son in a family of thirteen. His parents were well-to-do; and he received a thorough preliminary training at the Hopkins Grammar School, New Haven, Colin., passing thence to the Columbia School of Mines, in New York, where he was graduated in 1876. His first professional work was that of analytical chemist with a Cuban sugar company. In this position he spent a year, and, whatever else of benefit he may have acquired during that year in Cuba, he gained a facility of speech in the Spanish language which was of inestimable value in his subsequent work in Mexico and the southwestern United States. In 1877, he went to the Rocky Mountains, and, under the firm name of Murphy & Austin, opened an assay-ofice in Lead-ville, Colo., which was just then coming into public notice as a rich silver-lead camp. The next year, however, he entered the service of the Germania Smelting & Refining Co. at Salt Lake City, Utah, where he remained until 1882, first as assayer and chemist, and later as Assistant Superintendent. The Germa-nia bears the honorable distinction of being one of the first of the large " custom" lead-smelters erected in the West. Its founders may be called the pioneers of the modern lead-smeltr ing practice, and the Germania served, to a large extent, as a model for the many plants that sprang into existence during the next few years in Utah, southern Idaho, Colorado and other lead-producing districts. The formulation, for the first

Jan 1, 1908

By Horace H. Emerich

PrePatory Note.—The first part of this paper was sent to me by Mr. Emrich nearly nine months ago; and I held it, waiting for the second part, which he had promised to forward soon, so that I might submit the whole to some of his former professional associates, and advise him of their criticisms and suggestions before off'ering his work to the Institute. But, five days before the second part reached me, I received by telegraph the news of Mr. Emrich's sudden death. The paper has therefore not had the benefit of such a revision by the author as might have made it ill some respects clearer and more cornplete. Nevertheless, I believe that experts in the branch of metallurgy with which it deals will find it both original and suggestive.—A. Eilers. I. Partial ReFining iN the ANode-Furnace. During my connection with one of the large New Jersey copper-refineries, and probably before that period, from 15 to 30 per cent. of the copper-bullion received was the very foul, leady blister-copper produced from lead blast-furuace matte. It had been customary to mix a small part of this blister with each charge of purer pig-copper, in the effort to dilute it as much as possible before casting into anodes; but tank-house conditions were such that I was led to try making entire furnace-charges of this blister, and refining it as much as possible in the furnace—afterwards casting to anodes and refining elec-trolytically, in tanks and solution separate from the main bulk of the purer copper. In making this experiment, notes were made, for several furnace-charges, of everything thought to have a bearing on the question, and some interesting facts were brought out, both in the furnace-working and afterwards in the tanks.

Jan 1, 1913

By Anson Hayes, John Chipman

The quality of sheet and strip products made of rimming steel is closely related to the structure and chemistry of the ingots. The variation in composition throughout the ingot, as affected by segregation, is of great importance, as are also the form and distribution of the voids that result from the gases evolved. It is because of this importance that the considerable literature in this field has accumulated. No attempt is made in the present paper to compile a bibliography of the excellent work that has already been done, as this has been adequately covered in the many excellent reports on the heterogeneity of steel ingots prepared by a joint committee and published by the Iron and Steel Institute.' From time to time, in any field of investigation new tools and new technique are developed, which make further progress possible. In the field with which this paper is concerned, this is true. The development of the vacuum-fusion method as a means of following oxygen segregation, and a technique for obtaining the volume and composition of the gases evolved during solidification, have opened the way to obtaining data by means of which some considerable progress has been realized in developing more of the detailed mechanisms of solidification and segregation in rimming-steel ingots. General Theory of Segregation The basic cause of segregation lies in the fact that the impurities are less soluble in solid than in liquid iron. The solid that forms from the impure liquid is more nearly pure than the liquid itself. If solidification proceeds slowly enough, or if the liquid and solid phases are maintained in contact with one another for a sufficient time, a condition of equilibrium is set up, which may be represented by a phase diagram. Portions of the

Jan 1, 1939

By Anson Hayes, John Chipman

The quality of sheet and strip products made of rimming steel is closely related to the structure and chemistry of the ingots. The variation in composition throughout the ingot, as affected by segregation, is of great importance, as are also the form and distribution of the voids that result from the gases evolved. It is because of this importance that the considerable literature in this field has accumulated. No attempt is made in the present paper to compile a bibliography of the excellent work that has already been done, as this has been adequately covered in the many excellent reports on the heterogeneity of steel ingots prepared by a joint committee and published by the Iron and Steel Institute.' From time to time, in any field of investigation new tools and new technique are developed, which make further progress possible. In the field with which this paper is concerned, this is true. The development of the vacuum-fusion method as a means of following oxygen segregation, and a technique for obtaining the volume and composition of the gases evolved during solidification, have opened the way to obtaining data by means of which some considerable progress has been realized in developing more of the detailed mechanisms of solidification and segregation in rimming-steel ingots. General Theory of Segregation The basic cause of segregation lies in the fact that the impurities are less soluble in solid than in liquid iron. The solid that forms from the impure liquid is more nearly pure than the liquid itself. If solidification proceeds slowly enough, or if the liquid and solid phases are maintained in contact with one another for a sufficient time, a condition of equilibrium is set up, which may be represented by a phase diagram. Portions of the

Jan 1, 1939