Search Documents

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By C. S. Barrett

It has been observed that deformation in iron takes place by slip on (110) + {112) + (123) planesl, 2, but in silicon ferrite with low deformation temperatures or high silicon contents (exceeding 4 per cent) the authors have found that slip is confined wholly to (110) planes, at least with small amounts of deformation. The purpose of the present investigation was to determine the effect of this alteration of slip mechanism on preferred orientations in cold-rolled and recrystallized strips. Incidental observations on the effect of the recrystallization temperature were also made. The numerous determinations of the texture of cold-rolled iron and steel have been in satisfactory agreement as to the principal features of the texture (with the exception of a few conclusions that apparently have been based on insufficient data). The texture is chiefly one in which 11101 directions of the grains lie along the direction of rolling, with a deviation of a few degrees, and in which the (100) planes lie in the plane of the rolled sheet, with a deviation from this position chiefly about the rolling direction as an axis. This deviation about the rolling direction as an axis has been measured by different observers and lies between about 45" and 50" or 60" for iron5, 6, 9 and is usually in the neighborhood of 50" for mild stee16, 7, 8. The range of this deviation is a function of the percentage of total reduction8, 10. Post8 reported that it decreases with increasing percentage reduction, but apparently he studied only the surface material, which Gensamer and Meh17 found to be somewhat differently oriented from the material in the inside of the sheet. McLachlan and Davey10 found that the deviation also decreases with increasing percentage of total reduction for the material in the interior of the sheet and is independent of the percentage of reduction per pass. The deviation about the cross direction as an axis (the direction in the

Jan 1, 1937

By Louis Doremus Huntoon

HAVE been asked many times by financial men in New York as to the best way of securing an interest or control of a gold mine in Canada. It must be understood at the start that prospectors and early owners will not sell a 100 per cent interest. They not only retain from 10 to 25 per cent interest, depending upon the work done, but usually demand more or less cash to reimburse them for expenses. These conditions are accepted by Canadian capital and operating mines looking for new properties. The winter is not a hindrance to work but may be of great advantage. The overburden of soil and gravel is generally wet and most difficult to trench in the summer time especially if at all deep. The snow also permits easy transportation of freight. Properties distant from rail transport all of their machinery and supplies during the winter months.

Jan 1, 1933

By L. I. Cothern

THE introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various "wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these, advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By L. I. Cothern

The introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various ''wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By L. I. Cothern

The introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various ''wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

THE first mention of the mining and use of coal in the Pittsburgh district refers to the mine under Duquesne Heights that furnished coal for the garrison at the fort at Pittsburgh in 1760. Coal had been dug and used as fuel just outside of Brownsville, Fayette county, in 1759, but this was not a regular mine as the opening was in an outcropping. Maps of Ohio in 1770 showed "Cole Mines" at various points. The Penns purchased all the coal south of Kittanning in southwestern Pennsylvania from the Chiefs of the Six Nations for a reported price of $10,000. During the Revolution, coal from Herron Hill, Minersville, and Coal Hill, all within the present city limits, was used in Pittsburgh. There is today one custom pit opened in Coal Hill (Duquesne Heights). The first steam engine was set up in Pittsburgh in 1794 and used coal as fuel. The first mine in the Youghiogheny gas district was opened in 1796. In 1803, the first shipment of coal by water was made from Pittsburgh down the Ohio river and landed at Philadelphia, where it sold for approximately $9.50 per ton. The mines along the Monongahela were naturally the first to be opened. With the completion of locks and dams in 1844, permitting slack-water navigation, the industry began to thrive. The No. 8 field of Ohio and the Fairmont region of northern West Virginia were opened in the period 1840 to 1855. From that time on there has been a continuous development of the coal resources of this district, until at present-productive capacity is enough to supply 30 per cent. of the country's needs of bituminous coal. The original method of working the Pittsburgh seam was to drive under cover at some .easily accessible point on the outcrop with a single entry, usually 1 1/2 yd. wide. Rooms or gangways were turned to the

Jan 10, 1926

The first mention of the mining and use of coal in the Pittsburgh district refers to the mine under Duquesne Heights that furnished coal for the garrison at the fort at Pittsburgh in 1760. Coal had been dug and used as fuel just outside of Brownsville, Fayette county, in 1759, but this was not a regular mine as the opening was in an outcropping. Maps of Ohio in 1770 showed "Cole Mines" at various points. The Penns purchased all the coal south of Kittanning in southwestern Pennsylvania from the Chiefs of the Six Nations for a reported price of $10,000. During the Revolution, coal from Herron Hill, Mincrsville, and Coal Hill, all within the present city limits, was used in Pittsburgh. There is today one custom pit opened in Coal Hill (Duquesne Heights). The first steam engine was set up in Pittsburgh in 1794 and used coal as fuel. The first mine in the Youghiogheny gas district was opened in 1796. In 1803, the first shipment of coal by water was made from Pittsburgh down the Ohio river and landed at Philadelphia, where it sold for approximately $9.50 per ton. The mines along the Monongahela were naturally the first to be opened. With the completion of locks and dams in 1844, permitting slack-water navigation, the industry began to thrive. The No. 8 field of Ohio and the Fairmont region of northern West Virginia were opened in the period 1840 to 1855. From that time on there has been a continuous development of the coal rcsources of this district, until at present productive capacity is enough to supply 30 per cent. of the country's needs of bituminous coal. The original method of working the Pittsburgh seam was to drive under cover at some easily accessible point on the outcrop with a single entry, usually 1½ yd. wide. Rooms or gangways were turned to the right and left from this entry and ventilation was usually poor and inade-

Jan 1, 1927

By Richard W. Markley

A centralized online data acquisition system has been developed by the U.S. Bureau of Mines Pittsburgh Mining and Safety Research Center for rapidly digitizing, storing, and processing experimental signals originating up to 1100 feet away from a central computer. This system, which services seven laboratories, is currently based on a CDC System 17 1/- computer with 56K of semiconductor memory, four disk drives (one shared online with a CDC 1700), two magnetic tape drives, high-speed A/D hardware, and other input/output peripherals. The laboratories are linked to the central computer by 15-pair cables and signal conditioners and to the computer's communications controller by modems and current loops. The A/D throughput rate is approximately 30,000 samples per second (9 bit plus sign resolution) and permits scanning about 30 instruments once every millisecond for up to 100 seconds, being limited only by disk capacity. The laboratories serviced by this facility conduct explosions research and include such facilities as an Experimental Coal Mine Explosion Facility (45 channels), a Constant Volume Combustion Laboratory (4 channels), and a Simulated Coal Mine Laboratory (15 channels). Personnel support includes one systems analyst, two applications analysts, one operator, and a hardware technician. The system has performed adequately for burst-type data acquisition, but due to a lack of long-term reliability (24 hours) of the real-time multiprogramming operating system and unpredictable power failures, slow phenomena signals are generally digitized and stored offline. This latter data is input to the computer through peripherals such as a high-speed paper tape reader, or high-speed asynchronous communications ports. Processing of data is done either in real-time (as soon as data is collected) or in batch mode. Smaller batch jobs are run on this computer, and all others are transmitted by means of the system's high-speed UT 200 terminal simulator to a CDC-6000 series computer.

Jan 1, 1977

By B. C. Burgess

AFTER many years of close and friendly association with talc and soap-stone, this orthographically distinguished mineral steps forth in this edition, for the first time in a chapter of its own. Pyr, the Greek for fire, and phyllite, a rock or stone, form its name and at the same time refer to the first recorded use of pyrophyllite as firestones or hearthstones. Another derivation of "phyllite" is from the Greek phyllites, "of leaves," alluding to the beautiful white radial crystal aggregates that form when pyrophyllite is heated. Pyrophyllite used by the Chinese for carving is called agalmatolite, from the Greek agolma, meaning an image. COMPOSITION AND PROPERTIES Pyrophyllite has previously been grouped with talc because of the close similarity of the minerals in physical and optical properties. They have the same space group; and chemically they are closely related, pyrophyllite being the aluminum silicate A12Si4010(OH)2 and talc the magnesium silicate Mg3Si4010 (OH) 2. Another arrangement of the pyrophyllite formula is generally given as A12034Si02H20 because it expresses the chemical composition as usually determined (alumina 28.3 pct, silica 66.7 pct, water 5.0 pct). Vanderbilt gives pH values of pyrophyllite 5.6 to 8.4.29 Pyrophyllite usually is white, pale green, cream or pale yellow, buff or light gray. It is found in darker shades and other colors principally due to oxidation of contained iron minerals. It is translucent in thin sections. In hardness it is 1 to 2 in the Mohs scale. Its specific gravity is 2.8 to 2.9. In bulk specific gravity, the powdered mineral ranges from 0.4 to 0.7. Its luster is pearly to dull; it is infusible in the Bunsen burner flame, slightly affected by aqueous solutions of sodium carbonate and hydrochloric acid. It is decomposed by sulphuric acid, with separation of gelatinous silica. It is characterized chiefly by its micaceous structure and cleavage, its softness and greasy feel. Two other varieties occur

Jan 1, 1949

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

In magnetic taconite of the East Mesabi range, quartz, magnetite, and cummingtonite (OH}(Fe, Mg)(Si4O11)2) are the three major ore-forming minerals.' Fine grinding and magnetic separation of the taconite leads to a concentrate analyzing 64 to 65 pct Fe and 8 to 9 pct insoluble; the gangue content of the concentrate arising from the presence of locked magnetite-gangue particles, and of occluded gangue particles in magnetic floccules. To further upgrade such taconite concentrates, flotation appears to offer a particularly promising approach. To evaluate its effectiveness in separation, a knowledge of the flotation characteristics of each mineral comprising the concentrate becomes desirable. The floatability of magnetite and of quartz have already been reported in a previous paper,2 in which the flotation characteristics of the two minerals were correlated with the electrokinetic properties at the mineral-solution interfaces. Since cummingtonite has somewhat intermediate chemical composition between the above-named oxides, the electrokinetic and the flotation behavior of this mineral becomes of interest for both practical and fundamental reasons. In the present article the results of electrophoretic mobility measurements and of Hallimond tube flotation tests on cummingtonite are reported and are compared with those of quartz and magnetite. MATERIALS AND METHODS A sample of cummingtonite-rich taconite, received from the Mitchell pit, near Babbitt, Minn., was crushed and ground through 100 mesh, and the product was fractionated magnetically into three portions. First, a drum-type laboratory cobber was used to separate a highly magnetic portion, consisting mainly of free, but also containing locked, magnetite particles. The cobber tailing was then passed in two stages through a Franz isodynamic separator. The middle fraction was isolated, and, upon examination petrographically, was ascertained to be principally cummingtonite. The 100 to 150 mesh fraction of this sample was selected for the present study. It was cleaned by leaching briefly with hot, dilute HC1 and then by rinsing repeatedly with demineralized water. A ground and elutriated fraction of -5p cummingtonite was used for the electrophoretic measurements.

Jan 1, 1961

By Paul L. Russell

7.5-1. introduction. The possible engineering uses of nuclear explosives were recognized with the first nuclear detonation. Subsequent experiments have demonstrated the ability of nuclear explosives to move very large volumes of rock and earth efficiently and at costs below conventional earth-moving methods. The ability to package a quantity of energy equivalent to a few million tons of conventional explosive in a container approximately 20 ft long and 36 in. in diameter enables easy emplacement and thus provides the potential for excavation on scales heretofore impossible. Space does not permit detailed discussion of the many experiments with conventional high explosives and with nuclear explosives that were performed in developing the information presented here. A bibliography is included for those wishing detailed information. Material from those sources and from personal experience has been used freely. 7.5-2. Nuclear Explosives. An explosion, in general, results from the very rapid release of a large quantity of energy within a limited space. This is equally true for both conventional and nuclear explosions, although the energy is produced in quite different ways. In the case of a conventional explosive, this energy arises from chemical reactions. In a nuclear explosion, the energy is produced as a result of the formation of different atomic nuclei by the redistribution of the protons and neutrons within the interacting nuclei. Nuclear energy is of a much higher order of magnitude than chemical energy when equal masses are considered, and the release of this energy is a thousand times more rapid than the fastest chemical detonations. Explosions may be produced by fission or fusion reactions. FISSION. When a free (or unattached) neutron enters the nucleus of a fissionable atom, it can cause the nucleus to split into two smaller parts. This fission process is accompanied by the release of a large quantity of energy. The complete fission of 1 lb of uranium can produce as much energy as an explosion of 9,000 tons of TNT.

Jan 1, 1968

By T. A. Klinefelter, R. G. O’Meara, Glenn C. Truesdell, Richard W. Smith

THE investigation of domestic tales was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. I, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." HISTORY The use of steatite and talc in ceramic bodies goes back a great many years. If pure, tales shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a large business was carried on in the manufacture of tips for gas burners.1 With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Manchurian tales. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1943

By D. G. Brubaker

IN the history of geophysical exploration by the electromagnetic method many procedures and types of equipment have been used. Source arrangements for surveying on the ground have included long wires grounded at both ends, large loops laid on the ground, small horizontal loops, and vertical loops of moderate to small sizes. Receivers have ranged from simple direction-finding coils to combinations of coils and a bridge circuit to measure quantities related to both amplitude and phase of the received signal. Primary considerations in choosing a survey method are effectiveness, speed, and economy. In work on the ground in which locating and outlining conducting bodies is the objective, methods using a vertical coil and a simple direction-finder have been found the most satisfactory. Mason1 and his associates applied such a method by setting up a vertical source loop, fed with low frequency alternating current by an engine-generator set. With a direction-finding receiver they surveyed lines along the ground in the plane of the loop, taking measurements at each station of the azimuth and inclination of the magnetic field direction. Deviations of this direction from the normal direction, that is, from horizontal and perpendicular to the traverse line, indicated a conducting body. Recent advances in design of light-weight generating equipment have encouraged using this and similar methods. In 1950 W. H. Westphal and the present writer developed a variation of this method and the apparatus for carrying it out. Their ideas were also based on experience with the Boliden Mining Co. method, which uses a small source coil and a vac- uum tube oscillator. The new procedure uses a small vertical source coil, powered by a vacuum tube oscillator, apd a direction-finding receiving coil. Source and receiver are kept a fixed distance apart and move as a unit along the survey lines. At each receiver station only the inclination of the magnetic field created by the source is measured. Source Unit: The source coil and a small vacuum tube oscillator together weigh about 45 lb. The source coil consists of about 60 turns of 10-gage

Jan 1, 1958

By W. J. Romanow

RECENT papers by Williams, Sherwood, and Boothby,1 Seybolt et al.2 Heikes; and Roberts4 attest to the increasing importance of the hexagonal ferromagnetic compound MnBi. Since the magnetic properties of MnBi crystals are highly anisotropic, it is useful and necessary to have appropriate aids for determining their orientations—a (00.1) standard stereographic projection and a corresponding table of crystallographic angles for this structure. The tables of crystallographic angles for the hexagonal system available in the literature5 are computed for c/a ratios greater than that of MnBi and cannot satisfactorily be used to find the crystallographic angles of MnBi. A table of angles between the crystallographic planes (HK.L) and (hk.1) was calculated for MnBi from the formula0 F=are cos Hh+Kk+ 1/2(Hk+hK) + 3/4 (a/c)2Ll/v(H2 + K2 + HK + 3/4 (a/c)2L2) (h2+ k2+hk + 3/4 (a/c)2l2) on an IBM Type 650 Magnetic Drum Data Processing machine. The lattice constants used are listed in Table I and are those determined by Willis and Rooksby7 at 20°C. More recently published values obtained by both X-ray and neutron diffraction"' show no difference from these significant to the calculation. From the crystallographic angles between the basal plane (00.1) and the general plane (hk.1) in Table I, an (00.1) standard stereographic projection was made for MnBi which is shown in Fig. 1. Acknowledgments The author wishes to thank R. G. Treuting and J. N. Hobstetter for their technical assistance, and Miss D. P. Booth for programing the IBM machine for the calculations. He appreciates the opportunity to read the paper of B. W. Roberts of General Electric Co. prior to its publication. References 1H. J. Williams, R. C. Sherwood, and 0. L. Boothby: Bulletin Amer. Physical Soc., 1956 vol. 1, p. 132. 2 A. U. Seybolt, H. Hangen, B. W. Roberts, and P. Yurcisin: AIME Trans., 1956, vol. 206, p. 605: Journal oF Metals, May 1956. 3R. R. Heikes: Physical Review, 1955, vol. 99, p. 446. .B. W. Roberts: A Neutron Diffraction Study of the Structures of Manganese B.W.Roberts:ANeutronDiffractionBismuthide, Physical. Review, 1956, vol. 104, p. 607. 5 A. Taylor and S. Leber: AIME Trans., 1954, vol. 200, p. 190; JouRNal of Metals February 1954. « C. S. Barrett: Structure of Metals, 2nd Ed., p. 635. McGraw-Hill Book Co. New York and London, 1952. 7B. T. M. Willis and H. P. Rooksby: Proceedings Physical Soc., London, 1954, vol. 67B, p. 290.

Jan 1, 1958

Following closely Marcona Corp.'s announcement of its new Marconaflo process for transporting mineral slurries by ship (see pp. 96-97, Sept. 1969 [ ]), Midland-Ross Corp. (M-R) now heralds its metallized iron pellet process which supplements Oregon Steel Mills1 (Oregon Steel) new Portland, Ore., plant. Harry J. Bolwell, president of M-R describes the company's M-R Pellet as "the most exciting advance in steelmaking in a decade, one which will profoundly affect the industry." In fact, other knowledgeable industry spokesmen believe that with these developments the mini-steel plant era is now here and that this technical development along with the Marconaflo process will revolutionize iron ore shipments and steelmaking. The M-R president predicts that electric furnaces can account for 20% of the annual U.S. steel production by 1975, compared with 14% at the present time because of these developments.

Jan 12, 1969

By Richard J. Gowen

THE FUTURE The environment in which we live appears to change so slowly that most of us are unaware that any change has occurred at all. As the years pass, we notice increasing smog in our cities, new variations in weather, the shifting landscape with changing populations, and subtle but ever present alterations in the quality of life. In considering the future of our environment, we find we must grapple with questions concerning the very future of life as we know it today. Questions of resources, technology, society, governance, and purpose. Let us focus on the future of our environment and, in particular, raise the question of who is responsible for the environment. We know that action, or lack of action, will clearly influence our future environment. It is fashionable to catalog the many short-sightedness of our forefathers in developing the technologies which support the style of living to which we have become accustomed. However, I shall struggle to resist the temptation to list the well known ills of our present environment. Rather, let us concentrate on the future in our consideration of the priority of the multitude of options proposed to relieve our current energy crisis. We have recently witnessed the dramatic effects of air pollution produced by Mount St. Helen's eruptions. In the state of South Dakota, we watched our blue skies turn hazy and felt our eyes sting with the presence of volcanic ash. We were appalled at the dramatic effects on the landscape, crops, transportation, and all aspects of life in communities immediately downwind of the volcanic eruption. But in a few weeks, life had returned to near normal on the earth's surface leaving the volcanic ash in the atmosphere to ultimately

Jan 1, 1983

By Henry C. Freeman

During the early period of the construction of the Illinois and Michigan Canal, about 1838, in excavating for the canal, where the present town of Utica stands, hydraulic limestone was discovered, and its value was recognized. A kiln for calcining and a mill for grinding were erected, and the cement was used in the construction of the locks of the canal. This property was subsequently bought by the present owner, Mr. James Clark, and the work has been continued to the present time in much the same primitive manner as it was begun. The bed is exposed in the Illinois River valley by stripping off a few feet of the covering rock. It is from 4 feet to 6 feet 9 inches thick, and nearly level, dipping gently to the northeast. The Utica Cement Company's establishment, which is two miles west of Utica and two miles east of La Salle, was an outgrowth of the Illinois geological survey. The writer was in charge of the district which included La Salle county, and, in working out the details of the geology of that county, discovered, below the Utica bed, another workable hydraulic limestone, which makes its appearance in the northern bluff of the Illinois River valley, rising above the water level at the point where the company's works are established. This cement group, of which there are several thin beds, lies just below the St. Peter's sandstone, with a few feet intermediate of transition-rock, which appears to represent the Calciferous, and is exhibited in place, in concretionary form, at the top of the bluff. The hydraulic beds are very regular, and the one worked by the company is 10 feet thick; or, speaking more definitely, there are two beds, separated by 18 inches of sandstone, lying about two feet above the bottom, and the two beds are worked as one, the sandstone being first cut out and removed, to prevent mixture. In 1869 I was invited to join with a company, and to take charge

Jan 1, 1885

By Jei Y. Choi, P. G. Shewmon

The surfrrce-diffusion coefficients (DJ for Aulg8 on (100) and (111) surfaces of copper have been determined between 1050" and 780°C using a new avuzlysis imd experimental procedure. The results are: D, has also been determined fm cua4 at 870°C, and the values found are 4.5 times larger than those measured by the grain boundary grooving technique for the same surface orientations. This difference is felt to result from the approximate nature of the mathematical solution used in the present work. Attempts to measure D, for silver on copper and silver surfaces indicated a means of matter transport different from surface diffision was dominant in moving tracer from the source out over the surface. Cnlculations and experiment both indicate that this is the flow of silver through the vapor phase which completely masks the much smaller flow due to surface diffusion. The previous self-difhsion studies of D, for silver and copper are discussed in terms of our own analysis and found to yield values of D, factors of lo5 or more greater than those found by the grain boundary grooving tech -nique. UNTIL about 5 years ago it was widely believed that the activation energy for surface diffusion, AH, , was less than that for grain boundary diffusion, AHb,, which in turn was less than that for diffusion through the lattice, AHz.' This was concluded from various evidence that D,> Db>Dl, and one tracer study of D, for silver on silver from which AH, was inferred.2 In 1959 Mullins and Shewmon demonstrated that D, could be determined from the kinetics of the growth of grain-boundary grooves.3 Using this procedure, Gjostein measured D, on copper between 800" and 1050°C and found that the activation energy was roughly equal to AHl .4 Subsequent work on copper,5" silver,',' and goldg between the melting temperature T, and 0.87 T, confirmed that AH, as determined using the grain boundary grooving or scratch-relaxation technique was equal to or greater than AHz. During the same period, Drew and Pye again determined AH, for silver on silver using a tracer techniquelo and a mathematical solution similar to that of Nicker son and arker.' Though the values of D, Drew and Pye measured at any given temperature were about 200 times smaller than those reported by Nickerson and Parker, they again found a low activation energy of about 10 kcal, or about one fifth that found at the higher temperatures with the mass transport technique. A distinguishing characteristic of these two previous tracer studies is that they have worked at low temperatures (-1/2 T,) where they felt volume diffusion was negligible and then analyzed these data as if all tracer atoms leaving the source flowed out into and remained in a homogeneous high-diffusivity surface layer of undefined thickness. This is totally different from the model used in the mass-transport studies or the studies of grain boundary diffusion, which assume the high-diffusivity surface layer to be only a few angstroms thick. If this latter model is applied to the earlier tracer studies, it is shown that the tracer has really pe!etrated into the lattice a mean distance of 1000A. Thus the tracer distribution observed after an anneal is thought to be due to the combined effects of surface and volume diffusion. Independent of the relative validity of the two models, it seems evident to us that any comparison of the values of D, as determined in these two ways is meaningless and misleading, since the values of D, and AH, obtained in these two ways would be totally different for the same physical distributions of tracer. Once the fundamental difference in the approaches of the two techniques is established, we are faced with the question of which model better approximates physical reality. Here all the evidence seems to be on the side of the ''thin surface layer" analysis. In fact, the authors of Refs. 2 and 9 do not argue for the "thick-layer model" we have described; they simply invoke it through the equation they use to calculate D, . The primary evidence for the thin-film approach is: a) grain boundary grooves and scratches widen in proportion to tU4 and Mullins' rigorous analysis shows that this is only valid for a surface layer which is quite thin relative to the width of the groove;11 b) all accepted or seriously discussed models of solid-vapor interfaces and high-angle grain boundaries assume that the disturbed region of the interface is at most a few a0 thick. With the above in mind, it was desirable to determine D, using a radioactive tracer and a "thin-

Jan 1, 1964

By Walter Miller

AFter a year's continued impact of war, the task of the petroleum-refining industry stands out clearly and looms up in larger aspect. This time it is not, as it was so largely in the first World War, simply a matter of increased quantity—more and more of the same petroleum products that had substantially been standard for years. In this era the emphasis is largely on newer and improved materials which had been produced, if at all, in comparatively insignificant quantities, and for which manufacturing equipment was not available on a large scale. At the beginning of 1942 four great product needs (besides a number of lesser ones) confronted the industry: 100-octane aviation gasoline, toluene for T.N.T. production, high-quality lubricating oils for aviation and Army equipment service, and petroleum chemicals for synthetic rubber manufacture. The difficulty in presenting a review of engineering progress in petroleum refining during 1942 is that there is so little one is free to say about so much which has been and is being accomplished. At the opening of 1942 the program was to increase the then existing capacity of 50,000 bbl. a day of aviation gasoline to over 150,000 bbl. daily by building new plants at an estimated installation cost of $150,000,000. Later in the year. after the announcement by President Roosevelt of a large increase in the program for war-plane building, additional contracts were made between the Reconstruction Finance Corporation and rehers to raise the capacity to 250,000 bbl. per day. The greatly increased scope of the war activities in all parts of the world, the obligation of the United States as the arsenal of the United Nations, and the greater importance and use of bomber, transport, and cargo planes will undoubtedly bring about plans and installations for a further increase in production of aviation gasoline over the present announced plan. In this connection, Jesse Jones, Reconstruction Finance Corporation Chairman, announced that as of Oct. 31 the R.F.C. had through its subsidiary Defense Plant Corporation entered into contracts for the construction, expansion, or equipping of 28 plants to increase 100-octane aviation gasoline production, but gave no data on 'capacity involved or completion dates. His list did not, of course, include a number of existing plants, and some installations being made by companies who are themselves financing the construction. Production from existing operating installations was materially increased in a number of instances as a result of pooling knowledge of improvements in operation and also by the exchange of Components going into 100-octane blend to enable greater quantities of aviation gasoline to be produced from the over-

Jan 1, 1943