Search Documents

By Charles W. DeWitt

The ore treated at the reduction plant (called Yangdei) of the Chiksan Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments come from Sajunkohl mine, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The average assay value in gold is $6.95 per ton. At the mine the ore is put into bins, and is then trammed over an 8 per cent, grade to the tipple bins above the mill, where the ore is drawn through the mill holes as desired. The capacity of the tipple bins is about 3,500 tons. Ore from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 1b. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore is brought in from the outside mines, and this method of sampling is

Jan 1, 1916

By R. I. Jaffee, F. C. Holden, H. R. Ogden, A. G. Imgram

The tensile and notch tensile properties of four refractory metals (molybdenum, tungsten, niobium (columbium), and tantalum) and one alloy (Mo-0.5Ti) were investigated. All the materials were evaluated in bar form, and the molybdenum and Mo-0.5Ti also were studied in sheet form. The notch sensitivity of each material was evaluated on the basis of several criteria, including the notch-unnotch strength ratio, the ductility transition, and the fracture transitions. USE of refractory metals as structural materials in aircraft and space vehicles may subject them to low-as well as high-temperature environments. At elevated temperatures, the usefulness of a material usually is limited either by strength considerations

Jan 1, 1962

By Henry Howe

1. Introduction.-This paper is based in large part on the examination of two rings, shown in section in Fig. 4 to 15, cut from an eroded 14-in. (35.56-cm.) gun, liner, and containing, according to Booth, Garrett, & Blair: Carbon, 0.380 per cent.; manganese, 0.655 per cent.; nickel, 2.810 per cent.; vanadium, 0; chromium, a few hundredths of 1 per cent.; tungsten, 0; molybdenum, 0. These rings were received from Admiral Joseph Strauss, then Chief of Ordnance, U. S. Navy, through the kindness of Mr. Hudson Maxim, Chairman of the Committee on Ordnance and Explosives,, of the U. S. Naval Consulting Board.

Jan 2, 1918

By Albert W. Giles

The splitting of the coal by partings is a familiar feature of many coal beds. The partings are normally argillaceous, more rarely sandy or calcareous. The material is usually fine-grained, less frequently coarse-grained to conglomeratic. Many partings are wedge-shaped, others are lenticular, and in some coal beds thin partings but one or two inches thick persist as thin sheets throughout areas of regional extent. The origin of the partings differs, and in some cases is obscure and uncertain. Origin of Thick Partings Wedge-shaped Partings Wedge-shaped partings are normally of indefinite linear extent but of short transverse section. They are developed adjacent to the borders of the original peat-forming swamp or around islands formed within the swamp, hence their presence is indicative of the approximate limit of the coal bed or of an interruption in the continuity of the coal bed. Following deposition of the parting gradual reestablishment of swamp conditions is followed by burial of the parting with accumulating peat. Partings developed adjacent to the borders of swamps normally thicken toward the periphery of the swamp and represent either detrital materials carried in from adjacent land areas during floods or materials carried in by advancing waves and currents after a barrier confining the swamp had been breached by the waves. Partings formed in the manner first mentioned should become coarser and more arenaceous toward the source of supply of the detrital materials, and the overlying and underlying coal should gradually grade into carbonaceous shale as the margin of the original swamp is approached. Partings formed by advance of waves across a barrier should be largely or entirely arenaceous, thin wedges of short longitudinal section, possibly with fossils of marine or brackish affinity. The subjacent coal normally should "pinch out" against the barrier, and the overlying coal continue to the barrier, or even extend across it, depending on the geographic conditions established following the breaching of the original barrier. Islands may be formed in swamps in a number of ways. They may represent local uplift of the swamp floor during earthquakes, or

Jan 1, 1934

By P. C. Kapur

A principal first-order and a minor summation term contribute to the solution to the discretized batch-grinding equation when formulated in cumulative retained mode. Depending on the inter relations hips between the selection and breakage parameters, the minor term may be advantageously modified in a number of ways. The reduced grinding equations thus obtained are solved by iterations to give relatively simple solutions which are tested against experimental data. The irn-plications and advantages of the reduced grinding equations are briefly discussed. In many instances, the trajectory of the particle-size distribution in a batch mill may be extracted from a set of particle mass balance equations as follows

Jan 1, 1971

By Leroy Palmer

ALL the domestic. production of magnesite during 1925 came from two states, California and Washington. Of a total of 120,660 tons of crude ore, 64,600 tons, or 54 per cent., were produced in California.1 Of .this quantity California produced about 99 per cent. of the caustic calcined, but only 10 per cent. of the dead-burned. The largest producer was C. S. Maltby, of San Francisco, who operated the Red Mountain mine, in Santa Clara County, and the Sampson mine, in San Benito County, under lease. These two mines have been studied by the author, and offer interesting comparisons as to mining and treatment methods and final products. GEOLOGY The general geology of the magnesite deposits of California has been described by Hess,2 Bain3 and others,4 and although a detailed discussion is not necessary here, a brief summary will assist in understanding mining conditions. California magnesite, when comparatively pure, is usually a white, fine-grained rock, with a conchoidal fracture, occurring in veins and lense-like masses in serpentine. The veins vary considerably in width, and usually occur in a series of more or less parallel veins intersected by other series or systems of veins, probably following original or secondary fissures in the enclosing serpentine. The most generally accepted theory of origin is that the magnesite was formed by the action of surface waters charged with C02 percolating downward through fissures and changing the magnesium silicates of the serpentine into magnesium carbonate.

Jan 1, 1927

By F. L. Ransome

The dike here described is exposed in the workings of the Wedge and Bachelor mines, on the southern side of Red Canon, north of the town of Ouray, Colorado. Its course is north 80° east, or nearly east and west, and it hades to the north about 10°. It rarely outcrops, and was nowhere seen at the surface near the mines. A specimen collected by Dr. A. C. Spencer about two miles to the westward, near the mouth of Red Creek, indicates, however, a probable exposure of the dike near this point. The Wedge and Bachelor mines lie in a nearly horizontal series of fine-grained, light-grey sandstones, alternating with beds of very fine-grained shale of the same color. The shale as encountered underground is unusually compact and massive, but weathers readily on exposure, and splits much after the manner of ordinary shale. When fresh it closely resembles some finely arenaceous limestones, but it does not effervesce with acids, and is eseentially a fine, indurated, siliceous silt. Near the surface, and near the top of the sedimentary series as

Jan 1, 1901

Jan 1, 1955

By W. S. Potter

The proportions of manganese and carbon in manganese steel are familiar to all…

Jan 1, 1915

By David Reger

LITTLE new oil was found in West Virginia, during 1923, but there were important discoveries of gas. Most of the large oil producers have contented themselves with pumping old wells or in drilling only enough new wells in defined territory to maintain a fairly constant production, the attitude being that no, profit is made in producing high-grade oil at a low price and that an eventual loss is sustained by draining the reserves of a limited commodity that, at some more favorable time, will be of much value. The representative of one large company said: "We have done nothing but pump old wells during 1923 and we have made no plans for 1924." Careful attention to producing wells has been the rule, there having been few abandonments; the belief is prevalent that small wells will eventually become profitable under more favorable marketing conditions. In natural gas, the opposite point of view prevails. Because of the vast capabilities of the state for producing gas, its output being ahead of all others, great systems of transportation and distribution into the markets of four adjoining states have been built and a demand has been created that no present, or apparently potential, production can satisfy. This demand has become so great that large distributing companies not only discourage new applications for service but advise old customers to install coal furnaces for auxiliary fuel; some have requested public-service commissions to grant higher 'rates against large industrial consumers than those allowed for domestic heating. The response to this known market has been a rapid increase in price, both at the well mouth and at the door of the ultimate consumer, and the industry has become so stable that the only uncertainty, or hazard, appears to be the question of the presence of gas in fair quantity in a given territory under consideration. Several oil companies have now forsaken their policy of selling gas, wells outright when drilled and ;have organized gas departments to drill for gas and to dispose of the daily output by meter to distributing corporations. With such companies and with other producers whose interest is chiefly gas, the year has been busy and profitable. Some new territory of apparently large value has been proved and deeper producing sands in old fields have been tapped.

Jan 3, 1924

The opening session* was held in the hall of the Franklin Institute, on Tuesday evening, June 20th, President Holley in the chair. The President introduced Mr. Franklin B. Gowen, who addressed the Institute as follows: Mr. President and Gentlemen : It has been made my pleasant duty to welcome you to the city of Philadelphia, but in so doing I shrink, with some natural reluctance, from appearing before an audience so much better fitted than I am to cope with the subjects which are usually presented to your association, and I can assure you that no trembling neophyte, first venturing within the groves of the Academy, or walking, with sacred reverence, in the gardens of Plato, felt more natural dread at the consequence of his own temerity than I do in appearing before an audience composed of geutlenlen belonging to a scientific society of which I am but too sensible that until now I have been a member only in name. In olden times, upon entering a temple sacred to the worship of any deity, it was customary to lay some offering upon the altar, and, in following this custom, it will be my duty, before entering upon the more pleasant part of the task which is assigned me, to call your attention to a subject with which I have been somewhat familiar, and which is entirely within the scope of your investigations, in the belief that I may throw out some hints or some suggestions of a process that may be fully developed by some of you, and eventually lead to the introduction of that which may be of service to the human race. The satirist who described the philosopher whom he met, as engaged in the process of extracting sunbeams from cucumbers,

By J. T. Michalak, H. W. Paxton

The recovery of the initial flow stress of poly-crystalline iron is characterized by a) a logarithmic time dependence; b) an increasing activation energy with increasing recovery; c) an increased ?,ate and fraction of recovery with decreased temperature of deformation; and d) an increased rate with increased deformation. Isochro)ml studies of the recovery of single crystals revealed more sluggish recovery. The original flou3 stress of single crystals could be regained by recovery anneals at 800"or 900°C. ThE great majority of the theoretical treatments and experimental studies of strain-hardening have been concerned with the close-packed lattices.' Very little effort has been expended on the bcc structure so that the theory of work-hardening of this lattice is essentially nonexistent. The limited amount of experimental data resulting from the direct studies on silicon-iron,2 low-carbon steel,3 and purified irons4"7 does not as yet permit a detailed analysis of the strain-hardening. Studies concerned with the effects of annealing following deformation have been few in number," have been somewhat limited in extent, and have had the disadvantage of using irons containing a substantial impurity content. The present research was undertaken to augment the limited knowledge we have of the characteristics of a bcc metal as regards strain-hardening and recovery from the strain-hardened state. The recovery of the flow stress has been employed since it was felt that the stress associated with the hardened state gives at least a fair qualitative description of the state of the imperfections causing the hardening. The study was concerned primarily with the recovery of flow stress following strain-hardening of polycrys-talline, zone-melted iron as a function of the amount of deformation, the temperature of deformation, and the time and temperature of the recovery anneal. A limited investigation of the recovery of the initial flow stress of single crystals of this same material as a function of the recovery temperature was also conducted in conjunction with the Lambot X-ray technique." MATERIAL The zone-melted iron used in this investigation was obtained through the courtesy of the American Iron and Steel Institute and Battelle Memorial Institute. The analysis, as given by the supplier indicated a maximum impurity content of 0.02 wt pct excluding those impurities listed in Table I. (The actual impurity content is very probably less than this since detection limits were considered as the amount of a particular impurity level.) Also listed in Table I are the interstitial impurity contents of the iron at various stages of experimental work indicating that these im-

Jan 1, 1962

Jan 1, 1935

By G. F. Jr. Butterworth

THE metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to produce in the stock a physical condition having the requisite properties. The first group consists 'of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat-treated by giving it a quench and a draw. These barrels will be referred to as "heat-treated" barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent. of manganese, show a single very pronounced point between 1300° and 1350° F. (704° and 732° C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure discussed below, Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure, shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under- a low magnification appears

Jan 7, 1919

By W. B. Mather

The object of this paper is to record and interpret data collected during the examination of over 250 barite deposits in the Central Mineral District of Missouri. In the course of this study, the origin of the deposits, which the author believes to be hydrothermal, has been given particular attention. Economic barite deposits occur in two main areas in Missouri: (I) in the Washington County District of Southeast Missouri, from which over 90 pct of the state's production is derived; and (2) in the Central Mineral District, which includes portions of 15 counties in Central Missouri (Fig I). Barite in the smaller Washington County District is mined from widespread low grade, relatively shallow residual deposits, whereas in the Central District, it is mined

Jan 1, 1948

By W. B. Mather

The object of this paper is to record and interpret data collected during the examination of over 250 barite deposits in the Central Mineral District of Missouri. In the course of this study, the origin of the deposits, which the author believes to be hydrothermal, has been given particular attention. Economic barite deposits occur in two main areas in Missouri: (I) in the Washington County District of Southeast Missouri, from which over 90 pct of the state's production is derived; and (2) in the Central Mineral District, which includes portions of 15 counties in Central Missouri (Fig I). Barite in the smaller Washington County District is mined from widespread low grade, relatively shallow residual deposits, whereas in the Central District, it is mined

Jan 1, 1948

By E. N. Cameron, H. M. Bannerman

During the years 1942-1934, about 125 New England deposits were mined for sheet and punch mica, and many others were briefly prospected. During this period the Geological Survey, United States Department of the Interior, carried on detailcd studies of the deposits and the pegmatite bodies that contain them. The primary purpose of the studies was to provide geological information that would contribute toward efficient mine development and operation. The studies were aimed directly at practical production problems. Detailed maps showing the structure of the deposits were prepared, and geological findings were closely correlated with data on specific yields and costs of mining and processing. The result is information that permits a reasonably accurate appraisal of the mica deposits of New England and the mining industry that they support. At a time when the future of the industry is in doubt, it seems desirable to submit this appraisal for consideration. Domestic mica deposits supply only a small fraction of the country's needs in normal times? for only the richest domestic deposits can compete with the low-cost mines of India and Brazil. However, the possibility that this country may be cut off from its supplies in time of war gives domestic deposits an importance much greater than their peacetime production would imply. New England supplied about 22 per cent of domestic output in 1943 and 1944, the peak years of wartime production. Its actual contribution to the war effort was greater, for the proportion of sheet mica of high quality in the New England product is higher than the average for domestic mica. The data analyzed below were collected for the Geological Survey by D. M. Larra-bee, A. H. McNair, J. J. Page, V. E. Shai-nin, G. W. Stewart, and the co-authors of this paper. The cooperation of officials of Colonial Mica Corporation and of mine operators and owners in furnishing information is gratefully acknowledged. D. M. Larrabee, A. H. McNair, and V. E. Shainin have made various suggestions based on critical reading of the manuscript. Analysis oF Warrtime Operations In considering the data presented in this report, it must be remembered that the scale of mica operations is very small compared with that of many other mining industries. The typical New England mica mine of 1943 and 1944 was worked by a crew of five or six men. Equipment was varied but on the whole extremely simple. The first stage of operation at a deposit was normally opencut mining. Drilling was done mostly with jackhammers powered by portable compressors driven by gasoline engines. Muck was shoveled by hand into buckets with a capacity of 45 to 35 ton and commonly hoisted by derrick to a dump adjacent to the cut. As operations were carried to greater depth, and the tram sition to underground mining was made, these methods were modified to a degree depending largely on the attitude of the deposit mined. At steeply dipping deposits,

Jan 1, 1948

By H. M. Bannerman, E. N. Cameron

During the years 1942-1934, about 125 New England deposits were mined for sheet and punch mica, and many others were briefly prospected. During this period the Geological Survey, United States Department of the Interior, carried on detailcd studies of the deposits and the pegmatite bodies that contain them. The primary purpose of the studies was to provide geological information that would contribute toward efficient mine development and operation. The studies were aimed directly at practical production problems. Detailed maps showing the structure of the deposits were prepared, and geological findings were closely correlated with data on specific yields and costs of mining and processing. The result is information that permits a reasonably accurate appraisal of the mica deposits of New England and the mining industry that they support. At a time when the future of the industry is in doubt, it seems desirable to submit this appraisal for consideration. Domestic mica deposits supply only a small fraction of the country's needs in normal times? for only the richest domestic deposits can compete with the low-cost mines of India and Brazil. However, the possibility that this country may be cut off from its supplies in time of war gives domestic deposits an importance much greater than their peacetime production would imply. New England supplied about 22 per cent of domestic output in 1943 and 1944, the peak years of wartime production. Its actual contribution to the war effort was greater, for the proportion of sheet mica of high quality in the New England product is higher than the average for domestic mica. The data analyzed below were collected for the Geological Survey by D. M. Larra-bee, A. H. McNair, J. J. Page, V. E. Shai-nin, G. W. Stewart, and the co-authors of this paper. The cooperation of officials of Colonial Mica Corporation and of mine operators and owners in furnishing information is gratefully acknowledged. D. M. Larrabee, A. H. McNair, and V. E. Shainin have made various suggestions based on critical reading of the manuscript. Analysis oF Warrtime Operations In considering the data presented in this report, it must be remembered that the scale of mica operations is very small compared with that of many other mining industries. The typical New England mica mine of 1943 and 1944 was worked by a crew of five or six men. Equipment was varied but on the whole extremely simple. The first stage of operation at a deposit was normally opencut mining. Drilling was done mostly with jackhammers powered by portable compressors driven by gasoline engines. Muck was shoveled by hand into buckets with a capacity of 45 to 35 ton and commonly hoisted by derrick to a dump adjacent to the cut. As operations were carried to greater depth, and the tram sition to underground mining was made, these methods were modified to a degree depending largely on the attitude of the deposit mined. At steeply dipping deposits,

Jan 1, 1948

Jan 1, 1961

By R. D. Leitch, W. P. Yant, R. R. Sayers

In 1924, the United States Public Health Service was requested to undertake a special study of stream pollution. The Public Health Service asked the United States Bureau of Mines to take up the study because the training and experience of the personnel of the former was considered not to be as well suited to this type of investigation as that of the Bureau of Mines. Under H. Foster Bain, then Director of the Bureau, field investigations were begun in the spring of 1925. Along with mine-drainage wastes, the problem of gas-house and coke-oven waste was investigated in the laboratory and a method of treatment by sodium hydrate and benzol was found to be promising. The idea was obtained by A. C. Fieldner, chief engineer of the Bureau Experiment Stations, on a trip to Germany in 1924. He saw a practical application of the process, but obtained no information as to definite chemical or mechanical processes. Because of the then pending American patent applications by the German firm, we made no attempt to develop our findings further. Shortly afterward, a similar method of treatment was developed in the United States,' and since that time we have devoted our attention entirely to mine drainage. This paper is a presentation of some general facts and information gathered during the past five years on coal-mine drainage. Scope of Work There was such a diversity of opinion at the time this work was begun, on the whole subject and apparently so little accurately known, that it was decided to undertake a basic study from which first, certain definite information might be evident, and second, what might be considered

Jan 1, 1931