Search Documents

By Edwin Ludlow

EDWIN LUDLOW, president of the American Institute of Mining and Metallurgical Engineers for the year beginning Feb. 15, 1921, is a well-known figure in the state that was the birthplace of the Institute-Pennsylvania-although he was born and educated in New York and is again one of its residents, after years of active work in the field. Mr. Ludlow was born at Oakdale, Long Island, and was graduated from the School of Mines at Columbia University with the class of 1879. After graduation, he became a civilian worker with the U. S. Engineer Corps under General William Ludlow, his brother, and for two years did river and harbor surveying along the New Jersey coast.

Jan 1, 1921

By C. G. Dunn, P. K. Koh

THE primary recrystallization texture in cold-rolled silicon iron, which is the matrix texture for developing the Goss texture or the cube-on-edge texture by secondary recrystallization at temperatures near 900°C,1-5,21 has not been adequately described. Thus from the present available information, it is not possible to explain satisfactorily both the grain-growth selectivity of the matrix and the often observed magnetic torque curve, which itself provides some information on the texture. Also lacking is information on the special annealing texture that develops in this material when the annealing temperature is 1200°C or higher and the rate of rise to temperature is extremely rapid. From the work of May and Turnbull5 and from unpublished work, it was known that isothermal annealing near 1200°C tends to reduce the extent of secondary recrystallization and that a much weaker cube-on-edge texture results if appreciable normal grain growth replaces secondary recrystallization. Koh and Dunn6,7 have obtained additional information on complex primary recrystallization textures from further studies made after normal grain growth. In these instances the initial textures were retained during normal grain growth. A similar result reasonably could be expected in the present study except for the presence of a grain growth ihibitor1-5,8,9.21 and its tendency to allow only a few grains to grow. However, any information on the orientations of grains in the special annealing texture, even if far from representative of the initial matrix texture, would provide useful information on the nature of the matrix texture. In the present texture study the method of Newkirk and Bruce,10 which is based on the methods of Geisler" and Schwartz, 12 is used to obtain a complete (110) pole figure of the primary recrystallization texture. The high-temperature annealing texture is determined simply from the orientations of a large number of selected grains. The kinetic nature of the process that produces the annealing texture is treated elsewhere13 and it is shown that a form of secondary recrystallization with a very high rate of nucleation occurs during rapid annealing at high temperatures. EXPERIMENTAL PROCEDURE Commercial 0.014-in. cold-rolled silicon iron strip (3.16 wt pct Si), prepared by two stages of cold rolling with an intermediate short anneal, was given a decarburizing 3-min anneal at 800°C. Me-tallographic studies indicated complete recrystallization. Short-time anneals at 900° C and at higher temperatures proved that secondary recrystallization had not begun at 800°C, in fact, the short additional anneals were still in the induction period of secondary recrystallization. A rapid rise to an annealing temperature of 1260°C (2300°F) was obtained in a BaC12and NaCl fused salt bath. The structures that resulted from anneals in the range 12- to 1000-sec duration were relatively finegrained, even though the growth was a form of exaggerated grain growth13 or secondary recrystallization with a high nucleation frequency.= Many of the grains were large enough for an X-ray study using a 5-mil X-ray beam. A transmission Laue Camera and an optical-mechanical stage for moving the grains into the X-ray beam were used. A total of 325 grains were X-rayed in this manner and the grain orientations determined. Complete (110) pole figures were obtained for the primary recrystallization texture using CoKa radiation at 30 kv in the back-reflection range, such as (220) for (110) poles, as described recently by Newkirk and Bruce.10 The low voltage serves to reduce the spurious white radiation to a minimum. A filter of 0.001-inch iron foil was located in front of the detector slit for transmission and in front of the beam slit for back reflection. A new and improved specimen holder extended the useful tilting angle range for transmission to 70 deg instead of 60 deg as previously reported.' A torque magnetometer was used to obtain the magnetic torque curves for a number of l-in. diam disk specimens. RESULTS The (110) pole figure of the material after recrystallization at 800°C is shown in Fig. 1. The positions of the pole concentrations are found to be

Jan 1, 1961

The Lead-Line Update held in conjunction with the 1977 SME-AIME Fall Meeting in St. Louis provided sessions on mining, mineral processing, extractive metallurgy, and economies to brief the record on the industry's activities and developments since the 1970 World Symposium on Lead and Line convened, also in St. Louis. Changes in the industry since 1970 have not been profound, notes the program committee, consisting of D. O. Rausch, F. M. Stephens, and B.C. Mariacher, cochairmen; and H. L. Clifford, S. C. Fall), and M. Snedeker. However, various environmental and conservation factors have had a direct impact on process consideration and operating practice; the result has been new mines, improved technology, and changing market opportunities. The general consensus of the participants is that the future for the Lead-zinc industry looks promising as new applications are found and new products resulting from intensive research reach the marketplace. The highlights of the HS technical papers presented at the 1977 session follows.

Jan 11, 1977

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Sept. 10 to Oct. 10, 1914: James D. Mooney, Akron, Ohio. J. Kojima, Ashio Copper Mine, Japan. Bernard A. Wilkinson, Guadalajara, H. Starkweather, Cripple Creek, Colo. Mexico. S. S. Langley, New York, N. Y. A. B. Parsons, Candor, N. C.. J. H. Warder, Chicago, Ill. Arthur Feust, Santo Domingo, Nicaragua. Lloyd T. Buell, Butte, Mont. G. B. Marshall, New York, N. Y. George R. Rogers, Gowganda, Canada. Henry Krumb, Salt Lake City, Utah. H. 0. Hammond, Douglas, Ariz. Herbert S. Kohlberg, El Paso, Texas. Percy E. Hohne, El Oro, Mexico. Wilbur L. Cross, Jr., Glen Carbon, Pa. Percy E. Barbour, Candor, N. C. Thomas H. Leggett, formerly-in charge of the mining interests of the American Smelting & Refining Co., has resumed practice as consulting engineer with offices in the Singer Building, New York, N. Y.

Jan 11, 1914

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Aug. 10 to Sept. 10, 1914: William Huff Wagner, Milford, Del.. Stanley C.- Herold, San Jose, Cal. Charles W. Hamilton, Tampico, Mexico R. J. Grant, Denver, Colo. A. M. Van Rensselaer, New London, Conn. John Lloyd, Wilkes-Barre, Pa. . Henry C. Carr, New York, N. Y. D. M. Riordan has been appointed to act as special adviser to the Secretary of the Treasury and has sailed on the U. S. S. "Tennessee" for Europe, where he will assist in aiding Americans in returning to the United States.

Jan 10, 1914

By Jerry R. Johanson

The practical application of rolling theory to the design of roll presses is reviewed along with aspects of plant operations which must be considered to produce the required product economically. Appropriate parameters to scale up from laboratory tests to full- scale press operation and improvements possible in existing operations are discussed.

Jan 1, 1977

By M. M. Rao, P. G. Winchell, R. J. Russell

A detailed analysis has been used to correlate the avalable thermodynami c da In on iron-ric11 Fe-Ni (41loys in the body-centered a, and the face-centered y phases. The inp ut injovrt~ation required by the a am lysis consists of tile heat of the a, to y transformation at 1123°K, the heat of mixing of y at 1123°K, tile specific heats of both a, and y (decomposed into Debye, electronic, and magnelic contributions), and the positional and magnetic entropies of both a, and y. PYLrrzary oirt.bul of the analysis is the free energy of each phase as a Junction of temperature and composition. FOr Fe-Ni alloys the adjustment of twenty-one parunletevs allows the accurate reproduction of enthalpy data for both phases, the heat of mixing- for y, the a/y equilibrinm compositions in the Fe-Ni phase diagram, and the usually accepted enthalpy and entropy of a and y iron. Also obtaitzed are fuirly accurate reproductions of electronic specific heat coefficients predicted from electron- to-atom ratio interpolations and To temperatuves eslimanted from transformation studies. Also considered in the calculation are the elastic constants, Curie temperatures, saturation magnlelizalion values, and indications of short- range order. The measnred activity coefficient of iron in anstetnite could not be accurately matched. The major source of uncertainty in the model is thought to be the magnetic contribution to the entropy of austenite. Calcrclations were extended to Fe-ni-C alloys using available carbon-acliuity data. The free energy of transformation from martensile to r at fixed composition was obtained as a function of nickel and carbon contetzt, and binary thetal-carbon phase diagrams Were estimaled as a function of nickel contenl. We needed thermodynamic information for Fe-Ni and Fe-Ni-C alloys at temperatures between 400" and 800°K in order to interpret the results of several phase-transformation studies. The most recent theoretical analysis of the thermodynamics of Fe-Nialloysl was based on a lumped-parameter, regular-solution model and used the Fe-Ni phase diagram available at that time.' Because significant difficulties were encountered in attempting to extend this analysis to Fe-Ni-C alloys, and because more experimental data has become available recently, we decided to attempt a new correlation. The analysis used here allows the extrapolation of measured and calculated thermodynamic values to lower temperatures and the extension of the thermodynamic analysis to Fe-Ni-C alloys. The structure of this correlation consists of expressions containing a total of twenty-one adjustable parameters. The forms of these expressions are discussed in the next section; however, a less formal summary is presented now to provide a physical overview of the model and to indicate its connections to prior work. Primary input information for this correlation is described below. The measured values of the specific heat of iron3 and its analysis475 and theoretical estimates of the specific heat of y* iron at low tempera- loys at 1123°K has been measured by solution calori-metry.7 The enthalpies of both a, and y have been measured most recently by Scheil and Saftig,B who used a dry-ice calorimeter. These data are used to formulate expressions for the heat of mixing of y and the heat of transformation of a, to y both at 1123°K. The a and y solubility limits in the Fe-Ni phase diagram have been redetermined recently9 by methods which assure a close approach to equilibrium. The a to y transformation can occur without change in nickel content or free energy at a temperature called TO; TO temperatures for various nickel contents have been estimated from transformation studies. The computed free-energy functions are adjusted by means of the parameters to fit both the phase diagram and the TO temperatures. Primary emphasis is placed on the phase diagram fit. Iron activities have been measured in Fe-Ni austenite10 between 973" and 1173°K. These activity data, which cannot be fitted accurately with our model, indicate that iron is substantially ideal in iron-rich austenite. Secondary, but helpful, information for the present correlation is provided by neutron diffraction and saturation magnetization measurements on both body-centered and face-centered Fe-Ni alloys."-'3 These results were interpreted11 in terms of composition-insensitive, localized magnetic moments on both iron

Jan 1, 1968

Three. meetings for the presentation and discussion of papers were held in 1914, as follows: The 107th Meeting, including the Annual Business Meeting, in New York, Feb. 16 to 19; the 108th Meeting, Aug. 10 to 14, in Salt Lake City, and the 109th Meeting, Oct. 8 to 10, in Pittsburgh, Pa., under the auspices of Iron and Steel Committee, Committee on Coal and Coke, Committee on Petroleum and Gas, Committee on Non-Metallic Minerals. Local Sections ' Three new local sections were established during the year, namely; / Pennsylvania Anthracite Section, Chicago Section, and Utah Section.

Jan 1, 1917

Three meetings of the Institute for the presentation and discussion of technical papers were held in 1913: The 104th meeting, comprising the Annual Business Meeting as well as technical sessions, was held at New York, Feb. 18 to 20, 1913; the 105th meeting was held at Butte, Mont., Aug. 16 to 21, 1913, at which papers obtained largely through the efforts of the Committee on Precious and Base Metals were presented; and the 106th meeting was held at New York, Oct. 16 and 17, 1913, under the auspices of the Iron and Steel Committee.

Jan 1, 1917

By N. LILIENBERGS

DURING the past few years, the requirements for steel have been raised so high that soundness is more important than ever before. The old practice was to mike steel ingots of sufficiently large sections to permit a considerable reduction of area in rolling and hammering to a given size, relying on the fact that by such rolling and hammering all cavities will be squeezed together and practically eliminated. The finished sizes, if found by inspection of the surface to be faultless, were therefore pronounced to be sound. But when such steel is ?worked up,? the manufacturer is surprised and disappointed to find that it splits, or that streaks and seams make the product unmarketable. Large sections, such as rails, beams or heavy forgings, may, within certain limits, be sufficiently strong, even if the sides of the cavities are only squeezed, and not welded together. But it is well known that, in the interior of heavy articles, under certain conditions, forging may develop small streaks into large cavities. Small sections, steel for ordnance and tubes, and numberless articles in the tool-trade, always show up the defects. It may be doubted whether cavities in steel ingots can ever be completely welded. The old theory, is, that the silver-clear blow-holes, without the blue oxide, can be welded by sufficient working. They are, however, not empty, but are filled with carbonic oxide. It is admitted that the "blue" cavities, resulting from air mechanically drawn down into the mold during the casting, can never be welded, because the oxide does not melt, and there would be no escape for it if it did. The only way in which steel can be made satisfactory for the above-named particular purposes is by having it ?dead molten." But then the trouble of piping is encountered. As is well known, a pipe is the result of the contraction of

May 1, 1906

By H. W. Schadler

The superplastic behavior of low carbon and manganese bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests are reported which indicate that high strain rate sensitivity (>0.5) and adequate elongations are achievable in ultrafine-grained steels 1 to 2 p, but at strain rates which are not commercially attractive. It has been demonstrated that the fine grain size is retained after long times and high strains if the temperature is kept within the range of the two-phase (a + ?) field. INTEREST in superplasticity has been stimulated by the desire to: 1) understand the origin of, and mechanisms responsible for, the large uniform elongations observed, and 2) exploit this property for commercial advantage in metal forming operations. Although the Zn-22 wt pct Al alloy presently being studied as a model material1-5 may find application in sheet forming and extrusion, the potential of super-plasticity should best be realized in large tonnage materials, such as steel and aluminum alloys. The degree of superplasticity in low-carbon and manganese-bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests on ultrafine grain size material are reported. Avery and Backofen6 and Hart7 have shown that geometrically stable flow leading to extensive uniform elongation in the tension test is associated with high values of the strain rate sensitivity, m, defined: Lozinsky had reported that titanium and zirconium experience permanent deformation if subjected to a constant load and cyclic heating through the temperature range of the phase transformation. Although strain rate sensitivities in excess of about 0.2 had not been reported previously for steel, permanent deformation had been observed11-13 in a wide variety of steels subjected to a constant load and cyclic heating through the temperature range of the a-? phase transformation. Thus by analogy, steel could be expected to exhibit high strain rate sensitivity but only in the a + ? condition. High strain rate sensitivity has been observed at 650°C (a + Fe3C), but not reported as such, by Bailey, Dickenson, and pearson14 in 1931 at a strain rate of about 10-9 per min. It then remained to determine whether high tensile elongations would be observed in a rate-controlled test at constant temperature and at what strain rate strain rate sensitivity values greater than 0.5 would be observed. Since previous experience8 had indicated the importance of fine grain size to realizing high m at reasonable strain rates, it was first necessary to produce an ultrafine grain size and then keep the grains from growing during the test. The results of this investigation show that fine grain size can be readily produced16 and maintained by restricting the temperature of testing to below the ? transus. Further, superplasticity (high m and large uniform elongation) is observed. However, the strain rate range is only marginally useful for commercial forming operations with the finest grain size produced. MATERIAL The material investigated initially was a 1.9 wt pct Mn, 0.42 wt pct C, hot-rolled bar previously used by Low and Turka1015 and available in the laboratory. The 0.500-in. round was cold-rolled to a 0.090-in. flat, annealed for 4 hr at 850°C in argon, air-cooled, and cold-finished to 0.050 in. Subsequently, four additional steels of the compositions given in Table I were investigated to explore the effects of manganese, carbon, and test temperature on the observed stress-strain rate behavior. These steels were melted under argon, cast to 0.75 by 2 by 5 in. slabs, hot-rolled at 850°C, surface-finished to 0.13 in., and cold-finished to 0.050 in. Sheet tensile specimens 0.200 in. x thickness with 1- or 2-in. gage length were cut parallel to the rolling direction. Table I also includes the nominal transformation temperatures for the AISI 1340 and the four experimental steels. EXPERIMENTAL PROCEDURE Production of Fine Grain Size. Ultrafine grain size (1 to 5 p) was considered essential for this studv. Grange16 has described two techniques for producing

Jan 1, 1969

By D. L. McDanels, J. W. Weeton, R. W. Jech

An investigation was conducted to determine the stress-strain behavior and tensile properties of metallic composites and to relate them to the properties of the base materials. Tungsten fibers in a copper matrix were chosen as the model sys-tem to investigate these properties. Room-temp-atzcre tensile and dynamic -modulus tests were used To meet the demand for improved structural materials, considerable effort is being directed toward the creation of composite materials. One such material under investigation is the fiber-reinforced composite, in which a ductile, relatively weak matrix is reinforced with high-strength fibers. Some work has been done on the reinforcement of metallic matrices with metallic fibers1"5 as well as with ceramic-whisker reinforcement. Summaries of much of this work have been published by Mach-lin7 and Baske~.' Work done at the Lewis Research Center of NASA-" has involved the making and testing of composites composed of a fiber, tungsten, and a matrix, copper, which were insoluble in each other. An equation was presented that showed the relation between the ultimate tensile strength of the composites and the strengths and relative volume percents of the components. This relation was verified experimentally for composites containing fibers extending the full length of the specimen as well as for composites reinforced with short-length or discontinuous fibers. Since the publication of the preliminary results,9'10 additional data have been obtained. This paper presents these data as well as analyses of the stress-strain behavior and the mechanics of deformation of uni-axially oriented, fiber-reinforced metallic composites, in which both components are mutually insoluble. EXPERIMENTAL PROCEDURE Composites were made with high-purity copper as the matrix and 3-, 5-, and 7-mil-diam tungsten wire as the reinforcing fiber. Some specimens were made in which the reinforcing fiber extended completely through the full length of the composite test section. The fibers were placed in ceramic to determine these properties. The composites were reinforced with either continuous or discontinuos tungsten fibers. The tensile properties and stress-strain behavior of composites reinforced with either type of reinforcement were similar, and in both cases the full strength of the fiber was utilized. tubes to insure axial orientation and infiltrated with copper at 2200°F for 1 hr. Composites were also made with short-length (3/8 in. long) 5-mil-diam tungsten fibers as discontinuous reinforcement and infiltrated under the same conditions. The reinforcing fibers in both cases were longitudinally oriented in the direction parallel to the tensile axis. Room-temperature tensile tests were conducted on the composites, stress-strain curves were obtained, and ultimate tensile strength and elongation were measured. Dynamic modulus of elasticity, based upon the resonant frequency induced in the flexural mode of vibration, was also determined for the composites and the components. A more detailed discussion of the experimental procedure employed in this investigation may be found in Ref. 11. RESULTS Room-temperature tensile tests were conducted on 3-, 5-, and 7-mil-diam tungsten wires which had been annealed for 1 hr at 2200°F and show the tensile strength of the wires to be 331,000, 327,000, and 290,000 psi, respectively. Since all the composites were infiltrated under these conditions, the strengths were considered to represent the strength of the fibers in the composites throughout this study. The average tensile strength of the annealed copper used as the matrix in this investigation was 27,800 psi. Results of room-temperature tensile tests on composites reinforced with 3-, 5-, or 7-mil-diam tungsten fibers are plotted as functions of composition in Fig. 1. These data represent previously reported datag,l0 as well as data more recently obtained. The line shown on each curve represents a prediction of tensile strength as a function of composition; the calculation of this line was explained in Refs. 9 and 10. A similar plot is presented in Fig. l(d) for composites reinforced with short-length, discontinuous 5-mil-diam tungsten fibers. Again, both the previously reported and the recent data are presented, and the line shown is identical to that shown for

Jan 1, 1965

By S. Dinda

A series of as -quenched 4340 bars were drawn through a carbide die to various reductions. The X-ray diffraction technique of Lopata and Kula was employed to detect preferred orientation in drawn martensitic steel bars with low amounts of deformation, as lord as 0.8 pct The specimen face of each bar examined was cut at a 45-deg angle to the bar axis. The reflecting planes in the 45-deg face were varied by appropriate rotation of the sample using a spectrogonionzeter. TIE X-ray bean of a diffractometer was reflected from the center of the bar and the diffracted intensity was delected with a proportional counter and recorded. Intensity peaks were developed by cold working for 110 planes oriented at 0 and 60 deg to the bar axis. The intensity peaks increased with increasing defortnalion us a preferred orientation with a 110 texture developed parallel to the drawing direction. The intensity peaks for deformed as-quenched specimens remain unchanged after tempering at temperatures as high as 1000°F. The same amount of preferred orienlalion was observed both inferritic (hot-rolled) and martensitic (as-quenched) structures after an equivalent amount of deformation. THE deformation of martensite with medium carbon content. less than 0.5 pct, has been studied by Breyer et a1.1,2 It was reported that changes in properties such as resistivity, carbide precipitation, and the introduction of a yield point phenomenon were produced after cold reduction of as-quenched AISI 4340 steel bars. Later, Breyer and Nachtman3 studied the effect of cold reduction upon X-ray line intensity. They showed that the integrated 110 line intensity increased with increasing deformation when the planes examined were perpendicular to the die drawing direction. The integrated 110 line intensity for planes oriented at 45 deg to the die drawing direction, in contrast, were found to slightly decrease. These changes were proposed to be consistent with the previously proposed model of a stress-induced ordering of carbon atoms in the vicinity of dislocations.1,2 Objections can be raised to the above interpretation of the X-ray results on two grounds: a) Rough structure factor calculations indicate that the intensity changes are too large (50 pct observed vs 2 pct calculated4,5) to be the result of changes in the location of iron atoms produced by the stress-induced ordering of the carbon atoms. b) The results might be explained in terms of preferred orientations, although X-ray evidence of the development of texture has not been reported in the literature for deformations as slight as 1 or 2 pct. The aim of the present work was to determine if preferred orientation was present in such cold-drawn martensitic steel bars. In drawn rod or wire there is generally a certain crystallographic direction which is aligned in the direction of the wire axis, and the crystallographic planes are distributed symmetrically around this "fiber axis".6-8 This type of cylindrical specimen, with the fiber axis located at the center, will show rotational symmetry. Lopata and Kula9 proposed an experimental method utilizing a specimen cut at 45 deg, see Fig. 1. The X-ray beam is diffracted from the center of this bar cross section. The specimen is rotated around an axis perpendicular to the bar axis and lying in the 45-deg cut face. This permits the angle between the normals to the reflecting planes and the bar axis to be varied from 0 to 90 deg.9 With this arrangement the errors due to absorption and irradiated volume compensate each other.' This greatly simplifies analysis of the data and is of considerable advantage for quantitative measurements. If there is preferred orientation in the specimen, more planes are oriented in a particular direction in the bar. When the bar is rotated to the favorable Bragg condition for that particular orientation, the intensity will be higher than that for some other angle. This technique was adopted for the present investigation.

Jan 1, 1969

By Eugene Grace

IN THE careers of the men to whom I have referred we find typified the development of the chief prob-lems of engineering. The first is to shape and direct the forces of nature and thus to bring the world's resources to add to the comfort and welfare of man-kind. That, in a word, is the problem of production. Engineers have made a supreme contribution to the solution of that problem. But I feel that we have two somewhat newer branches of engineering which must command more and more of our attention. Those are what might be termed commercial and human engineering. Of what value is all our efficiency in pro-duction if we do not distribute efficiently, economically and effectively? And of what value is any of it unless we can add to the happiness and deeper satisfaction of those engaged in industry, as well as those who enjoy its -products? I predict that the outstanding advances in business over the next ten years will be in improved merchan-dising and distributing methods. Herein lies a wide field of opportunity for the engineer. We have briefly reviewed certain qualities of engi-neers who have become successful business executives. Is it possible for us to say that the material success of all these men was due to any one characteristic com-mon to each one of them? Indeed, I venture to assert that there is one quality which, in the last analysis, is determining as to whether any roan shall realize material success in this world of ours. That quality-so notable in the character of each one of the men I have named-is sound judgment. Moments arise in every life when it is necessary to say "yes" or to say "no" to a particular proposition or to a proposed line of action. It is the man who says "yes" at the proper time and "no" at the proper time who, in the final analysis, realizes business success. The ability to do this wisely is the mark of sound judg-ment, which is necessary in a business executive. I have known many business men seemingly slow in their mental processes, possessed apparently, of little imagination and of none of the flair which gives fasci-nation to so many characters, and yet who, when crises come-be they big or be they little-are able so to steer their business courses that they move in the right direction instead of into shallow waters or upon the rocks of trouble.

Jan 4, 1928

PRESIDENT AND DIRECTOR JOHN R. SUMAN HOUSTON, TEXAS PAST PRESIDENTS AND DIRECTORS DONALD B. GILLIES CLEVELAND, OHIO H.- G. MOULTON NEW YORK, N.Y. TREASURER AND DIRECTOR KARL -EILERS SEA CLIFF, N. Y. VICE-PRESIDENTS AND DIRECTORS W. B. HENRY HOUSTON, TEXAS HENRY KRUMB NEW YORK, N. Y. ERIE V. DAVELER , NEW YORK N Y W. M PEIRCE PALMERTON, PA. PAUL D. MERICA NEW YORK, N. Y. LEROY SALSICH DULUTH, MINN.

Jan 1, 1941

PRESIDENT AND DIRECTOR DONALD B. GILLIES CLEVELAND, OHIO PAST PRESIDENTS AND DIRECTORS R. C. ALLEN CLEVELAND, OHIO D. C. TACKLING SAN FRANCISCO, CALIF. TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS H. G. MOULTON NEW YORK, N. Y. HARVEY S. MUDD Los ANGELES, CALIF. PAUL -D. MERICA NEW YORK, N. Y. WILFRED SYKES CHICAGO, ILL. WILLIAM B. HEROY HOUSTON, TEXAS HENRY KRUMB NEW YORK, N. Y.

Jan 1, 1939

By John F. Elliott, Robert D. Pehlke

The rate of reaction of nitrogen with liquid iron and with binary alloys of iron and Al, Cb, Cr, Ni, O, S, Si, and W were measured. The surface active elements, oxygen and sulfur, decrease the rate markedly. The other alloying elements have very little effect on the rate except when they function as deoxidizers, The rates of absorption and de-sorption were found to be equal. Several possible reaction mechanisms which may control the rate are considered. In order to describe completely the behavior of nitrogen in steelmaking processes, the mechanisms of mass transfer between the gaseous and liquid phases, nitrogen and iron, respectively, must be understood. A kinetic study to determine the nature of these mass transfer processes was undertaken, and the results of that investigation are presented in this paper. Specifically, the study was directed toward determining the influence of alloying elements on the rates at which pure nitrogen gas at constant pressure is absorbed and desorbed by liquid iron solutions: A previous paper1 reported measurements of the equilibrium solubility of nitrogen in liquid binary iron alloys. The experimental data are presented and discussed first and then several possible rate limiting mechanisms are considered. PREVIOUS RESEARCH The results of several investigations on the rate of absorption of nitrogen by liquid iron and iron alloys have been reported.2-14 There is little agreement on the rate coefficients among these studies because of the influence of geometry on the experimental system and of the purity of the liquid iron. The rate was found to be influenced by alloying content for the binary liquid iron systems: Fe-Al,2 Fe-C,4,6 Fe-Cr,4,5,8 Fe-Mn,5 Fe-Ni,5,8 Fe-O,9,10 Fe-O,9,10 and Fe-Si.2,6,7,11 Several investigators12"15 have reported that the rate of nitrogen absorption is increased in a reducing gas mixture and decreased in an oxidizing atmosphere. A mechanism for the retardation by oxygen of the absorption of nitrogen has been described by Naeser18 as the formation of an iron oxide film at the gas-metal interface. The film slows the absorption rate until it disolves in the metal, thus permitting nitrogen to enter the liquid iron. Karwat17 discussed the influence of oxygen in terms of the formation of gaseous molecules of nitrous oxide which represent a higher energy form than the nitrogen and oxygen or the oxidizing gas and consequently constitute an energy barrier for the process. Fischer and Hoffmann10 showed that the oxygen markedly reduces the rate of absorption of nitrogen, the rate constant being one order of magnitude smaller in liquid iron containing 0.15 to 0.24 pct 0 as compared to that in melts containing 0.001 to 0.02 pct 0. Although Chipman and Murphy2 reported that the rate of absorption of nitrogen in liquid iron was essentially independent of temperature, Eklund3 found that the rate increases strongly with increasing temperature as did Kootz4 and Saito.5,6 Karnaukhov and Morozov7 also reported a large temperature coefficient, but related it to increased stirring at higher power inputs in an inductively heated system. All of the authors above have treated their results assuming that the reaction is diffusion controlled, that the surface reaction is in equilibrium with nitrogen gas, and that a "first order" reaction takes place. Karnaukhov and Morozov7 and Humbert; who studied the rate of absorption in a closed system by observing pressure changes in the system as a function of time, concluded that their results best fit a diffusion-type analysis. This was further verified by von Bogdandy, Dick, and stranski18 and Fischer and Hoffmann10 who found the initial rate of

Jan 1, 1963

By Avnulf Muan, Egil Aukrust

The activity-composition curve for cobalt oxide in (Co,Fe)304 solid solutions with spinel-type stmcture has been determined experimentally by studying the equilibrium between the spinel phase and a coexisting cobaltowüstite phase, "(Co,Fe)O", at 1200°C. A large negative deviation from ideal behavior prevails in the spinel at low cobalt oxide concentrations and a positive deviation at high cobalt oxide concentrations. The activity-composition curve for iron oxide in the solid solution is determined from the above curve by integvation of the Gibbs-Duhem equation along the join Co3O4,-Fe3O4. The standard free energy of formation of cobalt ferrite, CoFe2O4, from the oxide components CoO and Fe2O3 is calculated to be -8.2 kcal. ThERMODYNAMIC properties of (CO,Mn)3O4 solid solutions with spinel-type structure have been presented recently.' The present paper deals with similar relations in another spinel solid-solution phase, that represented by the system Co3O4-Fe3O4. The principles involved in measurements and calculations of thermodynamic properties for the system Co3O4-Fe3O4 are analogous to those used and discussed in detail in the work on (CO,Mn)3O4. A (CO,Fe)3O4 solid solution coexists in equilibrium with a (Co.Fe)Ot solid solution over a considerable Here acOo1.33 and aao are the activities of cobalt oxide in the spinel and the oxide solid solutions, respectively, pO2, is the oxygen pressure of equilibration, and pb, is the oxygen pressure at which CoO and CosO4 coexist in equilibrium in the binary system Co-O at the same temperature. The activity-com position curve for cobalt oxide in the (Co,Fe)O solid solution in contact with metal has been determined in a previous investigation by the present authors.' The system shows a small positive deviation from linear behavior. Because of the large defect concentration in wiistite and in (Co,Fe)O solid solutions, one cannot assume that the activity-composition relations in the oxide phase coexisting with a spinel phase at relatively high oxygen pressures are the same as those prevailing in the oxide solid solution coexisting with metal. However, a Gibbs-Duhem integration over the ternary Co-Fe-0 solution can be used to determine activities of cobalt and iron, and hence of CoO and FeO, from a knowledge of the oxygen potentials. Several papers have dealt with the subject of application of the Gibbs-Duhem equation to multi-component systems. 3-6 In the present case, it was

Jan 1, 1964

By G. S. Cole, G. F. Bolling

ThE exact type of fluid flow which occurs in a solidifying ingot is important in determining subsequent grain structure. This has been shown in studies of natural Convection" and of forced stirring or other disturbances of the melt."16 We shall explicitly argue that a complement to the existing natural flow in an ingot should be more effective than other types of flow in promoting the columnar-to-equiaxed transition. The ultimate effects of fluid flow upon structure is one of the topics of solidification that we have investigated in the alloy system Pb-Sb, under conditions simulating casting. In Fig. 1, the essential features of a bidirectional growth apparatus are shown; horizontal freezing from water-cooled faces within a low-thermal-conductivity lavite boat is a reasonable simulation of an ingot section. Details such as the furnace and thermocouples are omitted in order to show the location of four permanent. magnets, each with a pole separation of 21 in. providing a central field of about 1000 Gauss. When coupled with a dc current imposed through appropriate connections made at the cooled faces, a flow of fluid is produced as shown schematically. This technique described by Pfann and ~orsi" is ideal for our purpose since the flow indicated is the same as that we observe to occur naturally in this system. Components of 99.999 pct purity were used for study and all due precautions were taken in alloy preparation to avoid contaminants. Sections of the specimens were taken to ensure results representative of the interior as well as the surface of specimens. All proportions of equiaxed and columnar regions were measured by tracing the etched grain structures onto graph paper and simply counting squares. Four alloys were examined at superheats of 40" * 5°C and 100" * 9°C. Preliminary tests had shown that no appreciable enhancement of structure was obtained with magnetic field alone, so that this condition is not reported; it should nevertheless be noted that other configurations of magnetic field will reduce convection and thus enhance columnar growth.'8 For the tests reported the magnetic field was applied to a specimen by bringing the four preassembled magnets to a position 2 mm from an outer tube immediately after the ingot was poured. The dc current of 30 amps passed through the sample throughout the entire solidification cycle, resulting in a power dissipation of 9 w per sq cm of interface. This may be compared to the evolution of latent heat of approximately 18 w per sq cm. Table I contains the results of this experiment in terms of the total area ratio, equiaxed/columnar grains, as a function of the field interactions, solute concentrations, and superheats employed. The total structure of the ingot is seen to be most influenced when both the field and current are applied simultaneously; when current acts separately, little effect may be noted in spite of the heat supplied. In addition, the change in structure from the no field-no current case to the field-current condition is more pronounced at the higher superheat, and the higher the concentration of antimony. An example of the grain refinement, as well as the increased equiaxed zone, is shown in Fig. 2. It is now important to prove that there is indeed an increase in fluid flow due to the presence of the field-current interaction; this is done by temperature measurements in the liquid metal. Let us consider a bidirectional casting in which heat is applied to and removed from the system, in such a way that rate of solidification is zero.* When a sensitive thermocouple

Jan 1, 1967

By N. Van Wingen

EFFective sand permeabilities can be ascertained from core analysis if the laboratory data are compensated to allow for the presence of connate or residual water. Such adjustments can be made by applying empirically derived correction factors. Effective sand permeabilities can be estimated also from analytical studies of field depth-pressure measurements. In one method the time rate of pressure build-up after a well is shut in from steady-state flow is required, and in the other the direct measurement of a steady-state rate of flow and the corresponding equilibrium pressure. The results of the investigation discussed in this paper demonstrate that these methods for determining mean effective sand permeabilities can be correlated. Introduction In recent years many investigators have demonstrated the practical value of an accurate knowledge of the physical and dynamical characteristics of reservoir sands containing oil and gas. Of these factors, which serve to completely define a porous medium as a container or carrier of fluids, the dynamical characteristics are of particular interest to the production engineer because they afford a direct measure of the rate at which the oil or gas content of a reservoir will become available. The constant that defines dynamically the porous medium as the carrier of a homogeneous fluid in viscous motion is the "permeability." Coke-analysis Method The generally accepted practice in com-piling permeability data has been to analyze in the laboratory core samples taken in the course of drilling through the productive horizon, and to obtain the mean measure of the productive ability or permeability for the interval open to production by graphical integration of the permeability profile. An average permeability ascertained in this manner, however, is useful to the production engineer only for comparisons of wells drilled in the same horizon, as permeabilities determined in the laboratory are measures of only the ability of a porous medium to transmit a single fluid. As a result of many investigations, it has been shown, however, that under actual reservoir conditions water is coexistent with the petroleum and that its presence greatly reduces the permeability of the sand to oil. Empirical relationships showing the effect of the presence of any immiscible fluid A (such as water) in a porous medium on the permeability of the medium to a fluid B (such as oil) have been established separately by Hassler,1 Dunlap,2 and the writer (Fig. I),3 so that the average specific or dry-core permeability as determined in the laboratory can be corrected to give the true measure of the ability of the horizon penetrated to transmit oil, provided the percentage of pore space occupied by connate water is known accurately.

Jan 1, 1942